diff options
| -rw-r--r-- | bsp/imxrt/imxrt1064-nxp-evk/applications/main.c | 2 | ||||
| -rw-r--r-- | bsp/imxrt/imxrt1064-nxp-evk/board/Kconfig | 21 | ||||
| -rw-r--r-- | bsp/imxrt/imxrt1064-nxp-evk/board/MCUX_Config/clock_config.c | 220 | ||||
| -rw-r--r-- | bsp/imxrt/imxrt1064-nxp-evk/board/SConscript | 6 | ||||
| -rw-r--r-- | bsp/imxrt/imxrt1064-nxp-evk/board/board.c | 329 | ||||
| -rw-r--r-- | bsp/imxrt/imxrt1064-nxp-evk/board/board.h | 6 | ||||
| -rw-r--r-- | bsp/imxrt/imxrt1064-nxp-evk/board/ports/phyksz8081/fsl_phy.c | 315 | ||||
| -rw-r--r-- | bsp/imxrt/imxrt1064-nxp-evk/board/ports/phyksz8081/fsl_phy.h | 200 | ||||
| -rw-r--r-- | bsp/imxrt/imxrt1064-nxp-evk/board/ports/sdram_port.h | 49 | ||||
| -rw-r--r-- | bsp/imxrt/imxrt1064-nxp-evk/rtconfig.py | 6 |
10 files changed, 1028 insertions, 126 deletions
diff --git a/bsp/imxrt/imxrt1064-nxp-evk/applications/main.c b/bsp/imxrt/imxrt1064-nxp-evk/applications/main.c index 12c9d0df52..1b373138f2 100644 --- a/bsp/imxrt/imxrt1064-nxp-evk/applications/main.c +++ b/bsp/imxrt/imxrt1064-nxp-evk/applications/main.c @@ -18,6 +18,7 @@ int main(void) { +#ifndef PHY_USING_KSZ8081 /* set LED0 pin mode to output */ rt_pin_mode(LED0_PIN, PIN_MODE_OUTPUT); @@ -28,6 +29,7 @@ int main(void) rt_pin_write(LED0_PIN, PIN_LOW); rt_thread_mdelay(500); } +#endif } void reboot(void) diff --git a/bsp/imxrt/imxrt1064-nxp-evk/board/Kconfig b/bsp/imxrt/imxrt1064-nxp-evk/board/Kconfig index 7bfd46cf4b..4c7caa2d53 100644 --- a/bsp/imxrt/imxrt1064-nxp-evk/board/Kconfig +++ b/bsp/imxrt/imxrt1064-nxp-evk/board/Kconfig @@ -37,7 +37,28 @@ menu "On-chip Peripheral Drivers" endmenu menu "Onboard Peripheral Drivers" + + config BSP_USING_SDRAM + bool "Enable SDRAM" + default n + menuconfig BSP_USING_ETH + bool "Enable Ethernet" + select PHY_USING_KSZ8081 + select RT_USING_NETDEV + default n + + + if BSP_USING_ETH + config PHY_USING_KSZ8081 + bool "i.MX RT1064EVK uses ksz8081 phy" + default y + + config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE + bool "Enable the PHY ksz8081 RMII50M mode" + depends on PHY_USING_KSZ8081 + default y + endif endmenu menu "Board extended module Drivers" diff --git a/bsp/imxrt/imxrt1064-nxp-evk/board/MCUX_Config/clock_config.c b/bsp/imxrt/imxrt1064-nxp-evk/board/MCUX_Config/clock_config.c index 88dc4624c3..c26370df1c 100644 --- a/bsp/imxrt/imxrt1064-nxp-evk/board/MCUX_Config/clock_config.c +++ b/bsp/imxrt/imxrt1064-nxp-evk/board/MCUX_Config/clock_config.c @@ -1,4 +1,11 @@ /* + * Copyright 2018 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +/* * How to setup clock using clock driver functions: * * 1. Call CLOCK_InitXXXPLL() to configure corresponding PLL clock. @@ -15,15 +22,15 @@ /* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* !!GlobalInfo -product: Clocks v5.0 +product: Clocks v4.1 processor: MIMXRT1064xxxxA package_id: MIMXRT1064DVL6A mcu_data: ksdk2_0 -processor_version: 5.0.1 +processor_version: 0.0.0 +board: MIMXRT1064-EVK * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ #include "clock_config.h" -#include "fsl_iomuxc.h" /******************************************************************************* * Definitions @@ -57,35 +64,23 @@ outputs: - {id: CLK_1M.outFreq, value: 1 MHz} - {id: CLK_24M.outFreq, value: 24 MHz} - {id: CSI_CLK_ROOT.outFreq, value: 12 MHz} -- {id: ENET1_TX_CLK.outFreq, value: 2.4 MHz} - {id: ENET2_125M_CLK.outFreq, value: 1.2 MHz} -- {id: ENET2_TX_CLK.outFreq, value: 1.2 MHz} - {id: ENET_125M_CLK.outFreq, value: 2.4 MHz} - {id: ENET_25M_REF_CLK.outFreq, value: 1.2 MHz} - {id: FLEXIO1_CLK_ROOT.outFreq, value: 30 MHz} - {id: FLEXIO2_CLK_ROOT.outFreq, value: 30 MHz} -- {id: FLEXSPI2_CLK_ROOT.outFreq, value: 264 MHz} +- {id: FLEXSPI2_CLK_ROOT.outFreq, value: 2880/11 MHz} - {id: FLEXSPI_CLK_ROOT.outFreq, value: 2880/11 MHz} -- {id: GPT1_ipg_clk_highfreq.outFreq, value: 75 MHz} -- {id: GPT2_ipg_clk_highfreq.outFreq, value: 75 MHz} - {id: IPG_CLK_ROOT.outFreq, value: 150 MHz} -- {id: LCDIF_CLK_ROOT.outFreq, value: 67.5/7 MHz} +- {id: LCDIF_CLK_ROOT.outFreq, value: 67.5 MHz} - {id: LPI2C_CLK_ROOT.outFreq, value: 60 MHz} - {id: LPSPI_CLK_ROOT.outFreq, value: 105.6 MHz} - {id: LVDS1_CLK.outFreq, value: 1.2 GHz} -- {id: MQS_MCLK.outFreq, value: 1080/17 MHz} - {id: PERCLK_CLK_ROOT.outFreq, value: 75 MHz} - {id: PLL7_MAIN_CLK.outFreq, value: 24 MHz} - {id: SAI1_CLK_ROOT.outFreq, value: 1080/17 MHz} -- {id: SAI1_MCLK1.outFreq, value: 1080/17 MHz} -- {id: SAI1_MCLK2.outFreq, value: 1080/17 MHz} -- {id: SAI1_MCLK3.outFreq, value: 30 MHz} - {id: SAI2_CLK_ROOT.outFreq, value: 1080/17 MHz} -- {id: SAI2_MCLK1.outFreq, value: 1080/17 MHz} -- {id: SAI2_MCLK3.outFreq, value: 30 MHz} - {id: SAI3_CLK_ROOT.outFreq, value: 1080/17 MHz} -- {id: SAI3_MCLK1.outFreq, value: 1080/17 MHz} -- {id: SAI3_MCLK3.outFreq, value: 30 MHz} - {id: SEMC_CLK_ROOT.outFreq, value: 75 MHz} - {id: SPDIF0_CLK_ROOT.outFreq, value: 30 MHz} - {id: TRACE_CLK_ROOT.outFreq, value: 352/3 MHz} @@ -95,10 +90,10 @@ outputs: settings: - {id: CCM.AHB_PODF.scale, value: '1', locked: true} - {id: CCM.ARM_PODF.scale, value: '2', locked: true} +- {id: CCM.FLEXSPI2_PODF.scale, value: '1', locked: true} +- {id: CCM.FLEXSPI2_SEL.sel, value: CCM_ANALOG.PLL3_PFD0_CLK} - {id: CCM.FLEXSPI_PODF.scale, value: '1', locked: true} - {id: CCM.FLEXSPI_SEL.sel, value: CCM_ANALOG.PLL3_PFD0_CLK} -- {id: CCM.LCDIF_PODF.scale, value: '8', locked: true} -- {id: CCM.LCDIF_PRED.scale, value: '7', locked: true} - {id: CCM.LPSPI_PODF.scale, value: '5', locked: true} - {id: CCM.PERCLK_PODF.scale, value: '2', locked: true} - {id: CCM.SEMC_PODF.scale, value: '8'} @@ -107,6 +102,7 @@ settings: - {id: CCM_ANALOG.PLL1_PREDIV.scale, value: '1', locked: true} - {id: CCM_ANALOG.PLL1_VDIV.scale, value: '50', locked: true} - {id: CCM_ANALOG.PLL2.denom, value: '1', locked: true} +- {id: CCM_ANALOG.PLL2.div, value: '22'} - {id: CCM_ANALOG.PLL2.num, value: '0', locked: true} - {id: CCM_ANALOG.PLL2_BYPASS.sel, value: CCM_ANALOG.PLL2_OUT_CLK} - {id: CCM_ANALOG.PLL2_PFD0_BYPASS.sel, value: CCM_ANALOG.PLL2_PFD0} @@ -182,6 +178,77 @@ void BOARD_BootClockRUN(void) while (DCDC_REG0_STS_DC_OK_MASK != (DCDC_REG0_STS_DC_OK_MASK & DCDC->REG0)) { } + /* Init ARM PLL. */ + CLOCK_InitArmPll(&armPllConfig_BOARD_BootClockRUN); + /* In SDK projects, SDRAM (configured by SEMC) will be initialized in either debug script or dcd. + * With this macro SKIP_SYSCLK_INIT, system pll (selected to be SEMC source clock in SDK projects) will be left unchanged. + * Note: If another clock source is selected for SEMC, user may want to avoid changing that clock as well.*/ +#ifndef SKIP_SYSCLK_INIT + /* Init System PLL. */ + CLOCK_InitSysPll(&sysPllConfig_BOARD_BootClockRUN); + /* Init System pfd0. */ + CLOCK_InitSysPfd(kCLOCK_Pfd0, 27); + /* Init System pfd1. */ + CLOCK_InitSysPfd(kCLOCK_Pfd1, 16); + /* Init System pfd2. */ + CLOCK_InitSysPfd(kCLOCK_Pfd2, 24); + /* Init System pfd3. */ + CLOCK_InitSysPfd(kCLOCK_Pfd3, 16); +#endif + /* In SDK projects, external flash (configured by FLEXSPI2) will be initialized by dcd. + * With this macro XIP_EXTERNAL_FLASH, usb1 pll (selected to be FLEXSPI2 clock source in SDK projects) will be left unchanged. + * Note: If another clock source is selected for FLEXSPI2, user may want to avoid changing that clock as well.*/ +#if !(defined(XIP_EXTERNAL_FLASH) && (XIP_EXTERNAL_FLASH == 1)) + /* Init Usb1 PLL. */ + CLOCK_InitUsb1Pll(&usb1PllConfig_BOARD_BootClockRUN); + /* Init Usb1 pfd0. */ + CLOCK_InitUsb1Pfd(kCLOCK_Pfd0, 33); + /* Init Usb1 pfd1. */ + CLOCK_InitUsb1Pfd(kCLOCK_Pfd1, 16); + /* Init Usb1 pfd2. */ + CLOCK_InitUsb1Pfd(kCLOCK_Pfd2, 17); + /* Init Usb1 pfd3. */ + CLOCK_InitUsb1Pfd(kCLOCK_Pfd3, 19); + /* Disable Usb1 PLL output for USBPHY1. */ + CCM_ANALOG->PLL_USB1 &= ~CCM_ANALOG_PLL_USB1_EN_USB_CLKS_MASK; +#endif + /* DeInit Audio PLL. */ + CLOCK_DeinitAudioPll(); + /* Bypass Audio PLL. */ + CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllAudio, 1); + /* Set divider for Audio PLL. */ + CCM_ANALOG->MISC2 &= ~CCM_ANALOG_MISC2_AUDIO_DIV_LSB_MASK; + CCM_ANALOG->MISC2 &= ~CCM_ANALOG_MISC2_AUDIO_DIV_MSB_MASK; + /* Enable Audio PLL output. */ + CCM_ANALOG->PLL_AUDIO |= CCM_ANALOG_PLL_AUDIO_ENABLE_MASK; + /* DeInit Video PLL. */ + CLOCK_DeinitVideoPll(); + /* Bypass Video PLL. */ + CCM_ANALOG->PLL_VIDEO |= CCM_ANALOG_PLL_VIDEO_BYPASS_MASK; + /* Set divider for Video PLL. */ + CCM_ANALOG->MISC2 = (CCM_ANALOG->MISC2 & (~CCM_ANALOG_MISC2_VIDEO_DIV_MASK)) | CCM_ANALOG_MISC2_VIDEO_DIV(0); + /* Enable Video PLL output. */ + CCM_ANALOG->PLL_VIDEO |= CCM_ANALOG_PLL_VIDEO_ENABLE_MASK; + /* DeInit Enet PLL. */ + CLOCK_DeinitEnetPll(); + /* Bypass Enet PLL. */ + CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllEnet, 1); + /* Set Enet output divider. */ + CCM_ANALOG->PLL_ENET = (CCM_ANALOG->PLL_ENET & (~CCM_ANALOG_PLL_ENET_DIV_SELECT_MASK)) | CCM_ANALOG_PLL_ENET_DIV_SELECT(1); + /* Enable Enet output. */ + CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENABLE_MASK; + /* Set Enet2 output divider. */ + CCM_ANALOG->PLL_ENET = (CCM_ANALOG->PLL_ENET & (~CCM_ANALOG_PLL_ENET_ENET2_DIV_SELECT_MASK)) | CCM_ANALOG_PLL_ENET_ENET2_DIV_SELECT(0); + /* Enable Enet2 output. */ + CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENET2_REF_EN_MASK; + /* Enable Enet25M output. */ + CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENET_25M_REF_EN_MASK; + /* DeInit Usb2 PLL. */ + CLOCK_DeinitUsb2Pll(); + /* Bypass Usb2 PLL. */ + CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllUsb2, 1); + /* Enable Usb2 PLL output. */ + CCM_ANALOG->PLL_USB2 |= CCM_ANALOG_PLL_USB2_ENABLE_MASK; /* Set AHB_PODF. */ CLOCK_SetDiv(kCLOCK_AhbDiv, 0); /* Disable IPG clock gate. */ @@ -193,8 +260,14 @@ void BOARD_BootClockRUN(void) CLOCK_SetDiv(kCLOCK_IpgDiv, 3); /* Set ARM_PODF. */ CLOCK_SetDiv(kCLOCK_ArmDiv, 1); + /* Set preperiph clock source. */ + CLOCK_SetMux(kCLOCK_PrePeriphMux, 3); + /* Set periph clock source. */ + CLOCK_SetMux(kCLOCK_PeriphMux, 0); /* Set PERIPH_CLK2_PODF. */ CLOCK_SetDiv(kCLOCK_PeriphClk2Div, 0); + /* Set periph clock2 clock source. */ + CLOCK_SetMux(kCLOCK_PeriphClk2Mux, 0); /* Disable PERCLK clock gate. */ CLOCK_DisableClock(kCLOCK_Gpt1); CLOCK_DisableClock(kCLOCK_Gpt1S); @@ -203,6 +276,8 @@ void BOARD_BootClockRUN(void) CLOCK_DisableClock(kCLOCK_Pit); /* Set PERCLK_PODF. */ CLOCK_SetDiv(kCLOCK_PerclkDiv, 1); + /* Set per clock source. */ + CLOCK_SetMux(kCLOCK_PerclkMux, 0); /* Disable USDHC1 clock gate. */ CLOCK_DisableClock(kCLOCK_Usdhc1); /* Set USDHC1_PODF. */ @@ -241,9 +316,9 @@ void BOARD_BootClockRUN(void) /* Disable Flexspi2 clock gate. */ CLOCK_DisableClock(kCLOCK_FlexSpi2); /* Set FLEXSPI2_PODF. */ - CLOCK_SetDiv(kCLOCK_Flexspi2Div, 1); + CLOCK_SetDiv(kCLOCK_Flexspi2Div, 0); /* Set Flexspi2 clock source. */ - CLOCK_SetMux(kCLOCK_Flexspi2Mux, 3); + CLOCK_SetMux(kCLOCK_Flexspi2Mux, 1); #endif /* Disable CSI clock gate. */ CLOCK_DisableClock(kCLOCK_Csi); @@ -325,9 +400,9 @@ void BOARD_BootClockRUN(void) /* Disable LCDIF clock gate. */ CLOCK_DisableClock(kCLOCK_LcdPixel); /* Set LCDIF_PRED. */ - CLOCK_SetDiv(kCLOCK_LcdifPreDiv, 6); + CLOCK_SetDiv(kCLOCK_LcdifPreDiv, 1); /* Set LCDIF_CLK_PODF. */ - CLOCK_SetDiv(kCLOCK_LcdifDiv, 7); + CLOCK_SetDiv(kCLOCK_LcdifDiv, 3); /* Set Lcdif pre clock source. */ CLOCK_SetMux(kCLOCK_LcdifPreMux, 5); /* Disable SPDIF clock gate. */ @@ -356,85 +431,6 @@ void BOARD_BootClockRUN(void) CLOCK_SetMux(kCLOCK_Flexio2Mux, 3); /* Set Pll3 sw clock source. */ CLOCK_SetMux(kCLOCK_Pll3SwMux, 0); - /* Init ARM PLL. */ - CLOCK_InitArmPll(&armPllConfig_BOARD_BootClockRUN); - /* In SDK projects, SDRAM (configured by SEMC) will be initialized in either debug script or dcd. - * With this macro SKIP_SYSCLK_INIT, system pll (selected to be SEMC source clock in SDK projects) will be left unchanged. - * Note: If another clock source is selected for SEMC, user may want to avoid changing that clock as well.*/ -#ifndef SKIP_SYSCLK_INIT - /* Init System PLL. */ - CLOCK_InitSysPll(&sysPllConfig_BOARD_BootClockRUN); - /* Init System pfd0. */ - CLOCK_InitSysPfd(kCLOCK_Pfd0, 27); - /* Init System pfd1. */ - CLOCK_InitSysPfd(kCLOCK_Pfd1, 16); - /* Init System pfd2. */ - CLOCK_InitSysPfd(kCLOCK_Pfd2, 24); - /* Init System pfd3. */ - CLOCK_InitSysPfd(kCLOCK_Pfd3, 16); -#endif - /* In SDK projects, external flash (configured by FLEXSPI2) will be initialized by dcd. - * With this macro XIP_EXTERNAL_FLASH, usb1 pll (selected to be FLEXSPI2 clock source in SDK projects) will be left unchanged. - * Note: If another clock source is selected for FLEXSPI2, user may want to avoid changing that clock as well.*/ -#if !(defined(XIP_EXTERNAL_FLASH) && (XIP_EXTERNAL_FLASH == 1)) - /* Init Usb1 PLL. */ - CLOCK_InitUsb1Pll(&usb1PllConfig_BOARD_BootClockRUN); - /* Init Usb1 pfd0. */ - CLOCK_InitUsb1Pfd(kCLOCK_Pfd0, 33); - /* Init Usb1 pfd1. */ - CLOCK_InitUsb1Pfd(kCLOCK_Pfd1, 16); - /* Init Usb1 pfd2. */ - CLOCK_InitUsb1Pfd(kCLOCK_Pfd2, 17); - /* Init Usb1 pfd3. */ - CLOCK_InitUsb1Pfd(kCLOCK_Pfd3, 19); - /* Disable Usb1 PLL output for USBPHY1. */ - CCM_ANALOG->PLL_USB1 &= ~CCM_ANALOG_PLL_USB1_EN_USB_CLKS_MASK; -#endif - /* DeInit Audio PLL. */ - CLOCK_DeinitAudioPll(); - /* Bypass Audio PLL. */ - CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllAudio, 1); - /* Set divider for Audio PLL. */ - CCM_ANALOG->MISC2 &= ~CCM_ANALOG_MISC2_AUDIO_DIV_LSB_MASK; - CCM_ANALOG->MISC2 &= ~CCM_ANALOG_MISC2_AUDIO_DIV_MSB_MASK; - /* Enable Audio PLL output. */ - CCM_ANALOG->PLL_AUDIO |= CCM_ANALOG_PLL_AUDIO_ENABLE_MASK; - /* DeInit Video PLL. */ - CLOCK_DeinitVideoPll(); - /* Bypass Video PLL. */ - CCM_ANALOG->PLL_VIDEO |= CCM_ANALOG_PLL_VIDEO_BYPASS_MASK; - /* Set divider for Video PLL. */ - CCM_ANALOG->MISC2 = (CCM_ANALOG->MISC2 & (~CCM_ANALOG_MISC2_VIDEO_DIV_MASK)) | CCM_ANALOG_MISC2_VIDEO_DIV(0); - /* Enable Video PLL output. */ - CCM_ANALOG->PLL_VIDEO |= CCM_ANALOG_PLL_VIDEO_ENABLE_MASK; - /* DeInit Enet PLL. */ - CLOCK_DeinitEnetPll(); - /* Bypass Enet PLL. */ - CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllEnet, 1); - /* Set Enet output divider. */ - CCM_ANALOG->PLL_ENET = (CCM_ANALOG->PLL_ENET & (~CCM_ANALOG_PLL_ENET_DIV_SELECT_MASK)) | CCM_ANALOG_PLL_ENET_DIV_SELECT(1); - /* Enable Enet output. */ - CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENABLE_MASK; - /* Set Enet2 output divider. */ - CCM_ANALOG->PLL_ENET = (CCM_ANALOG->PLL_ENET & (~CCM_ANALOG_PLL_ENET_ENET2_DIV_SELECT_MASK)) | CCM_ANALOG_PLL_ENET_ENET2_DIV_SELECT(0); - /* Enable Enet2 output. */ - CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENET2_REF_EN_MASK; - /* Enable Enet25M output. */ - CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENET_25M_REF_EN_MASK; - /* DeInit Usb2 PLL. */ - CLOCK_DeinitUsb2Pll(); - /* Bypass Usb2 PLL. */ - CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllUsb2, 1); - /* Enable Usb2 PLL output. */ - CCM_ANALOG->PLL_USB2 |= CCM_ANALOG_PLL_USB2_ENABLE_MASK; - /* Set preperiph clock source. */ - CLOCK_SetMux(kCLOCK_PrePeriphMux, 3); - /* Set periph clock source. */ - CLOCK_SetMux(kCLOCK_PeriphMux, 0); - /* Set periph clock2 clock source. */ - CLOCK_SetMux(kCLOCK_PeriphClk2Mux, 0); - /* Set per clock source. */ - CLOCK_SetMux(kCLOCK_PerclkMux, 0); /* Set lvds1 clock source. */ CCM_ANALOG->MISC1 = (CCM_ANALOG->MISC1 & (~CCM_ANALOG_MISC1_LVDS1_CLK_SEL_MASK)) | CCM_ANALOG_MISC1_LVDS1_CLK_SEL(0); /* Set clock out1 divider. */ @@ -451,26 +447,6 @@ void BOARD_BootClockRUN(void) CCM->CCOSR &= ~CCM_CCOSR_CLKO1_EN_MASK; /* Disable clock out2. */ CCM->CCOSR &= ~CCM_CCOSR_CLKO2_EN_MASK; - /* Set SAI1 MCLK1 clock source. */ - IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR, kIOMUXC_GPR_SAI1MClk1Sel, 0); - /* Set SAI1 MCLK2 clock source. */ - IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR, kIOMUXC_GPR_SAI1MClk2Sel, 0); - /* Set SAI1 MCLK3 clock source. */ - IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR, kIOMUXC_GPR_SAI1MClk3Sel, 0); - /* Set SAI2 MCLK3 clock source. */ - IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR, kIOMUXC_GPR_SAI2MClk3Sel, 0); - /* Set SAI3 MCLK3 clock source. */ - IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR, kIOMUXC_GPR_SAI3MClk3Sel, 0); - /* Set MQS configuration. */ - IOMUXC_MQSConfig(IOMUXC_GPR,kIOMUXC_MqsPwmOverSampleRate32, 0); - /* Set ENET1 Tx clock source. */ - IOMUXC_EnableMode(IOMUXC_GPR, kIOMUXC_GPR_ENET1RefClkMode, false); - /* Set ENET2 Tx clock source. */ - IOMUXC_EnableMode(IOMUXC_GPR, IOMUXC_GPR_GPR1_ENET2_CLK_SEL_MASK, false); - /* Set GPT1 High frequency reference clock source. */ - IOMUXC_GPR->GPR5 &= ~IOMUXC_GPR_GPR5_VREF_1M_CLK_GPT1_MASK; - /* Set GPT2 High frequency reference clock source. */ - IOMUXC_GPR->GPR5 &= ~IOMUXC_GPR_GPR5_VREF_1M_CLK_GPT2_MASK; /* Set SystemCoreClock variable. */ SystemCoreClock = BOARD_BOOTCLOCKRUN_CORE_CLOCK; } diff --git a/bsp/imxrt/imxrt1064-nxp-evk/board/SConscript b/bsp/imxrt/imxrt1064-nxp-evk/board/SConscript index 4f8e797f9a..6afc7c3ae4 100644 --- a/bsp/imxrt/imxrt1064-nxp-evk/board/SConscript +++ b/bsp/imxrt/imxrt1064-nxp-evk/board/SConscript @@ -13,7 +13,11 @@ MCUX_Config/pin_mux.c CPPPATH = [cwd,cwd + '/MCUX_Config',cwd + '/ports'] -CPPDEFINES = ['CPU_MIMXRT1064DVL6A', 'STD=C99', 'SKIP_SYSCLK_INIT', 'EVK_MCIMXRM', 'FSL_SDK_ENABLE_DRIVER_CACHE_CONTROL','XIP_EXTERNAL_FLASH=1', 'XIP_BOOT_HEADER_ENABLE=1'] +CPPDEFINES = ['CPU_MIMXRT1064DVL6A', 'SKIP_SYSCLK_INIT', 'EVK_MCIMXRM', 'FSL_SDK_ENABLE_DRIVER_CACHE_CONTROL=1','XIP_EXTERNAL_FLASH=1', 'XIP_BOOT_HEADER_ENABLE=1', 'XIP_BOOT_HEADER_DCD_ENABLE=1'] + +if GetDepend(['PHY_USING_KSZ8081']): + src += Glob('ports/phyksz8081/fsl_phy.c') + CPPPATH += [cwd + '/ports/phyksz8081'] if rtconfig.CROSS_TOOL == 'keil': CPPDEFINES.append('__FPU_PRESENT=1') diff --git a/bsp/imxrt/imxrt1064-nxp-evk/board/board.c b/bsp/imxrt/imxrt1064-nxp-evk/board/board.c index a56282ea00..0ef8769e0e 100644 --- a/bsp/imxrt/imxrt1064-nxp-evk/board/board.c +++ b/bsp/imxrt/imxrt1064-nxp-evk/board/board.c @@ -12,6 +12,8 @@ #include <rtthread.h> #include "board.h" #include "pin_mux.h" +#include "fsl_iomuxc.h" +#include "fsl_gpio.h" #ifdef BSP_USING_DMA #include "fsl_dmamux.h" @@ -109,6 +111,325 @@ void imxrt_dma_init(void) EDMA_Init(DMA0, &config); } #endif + +#ifdef BSP_USING_LPUART +void imxrt_uart_pins_init(void) +{ +#ifdef BSP_USING_LPUART1 + + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 is configured as LPUART1_TX */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 is configured as LPUART1_RX */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 PAD functional properties : */ + 0x10B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 PAD functional properties : */ + 0x10B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Disabled */ +#endif +#ifdef BSP_USING_LPUART2 + + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_02_LPUART2_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_03_LPUART2_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_02_LPUART2_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_03_LPUART2_RX, + 0x10B0u); + +#endif +#ifdef BSP_USING_LPUART3 + + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_06_LPUART3_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_07_LPUART3_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_06_LPUART3_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_07_LPUART3_RX, + 0x10B0u); +#endif +#ifdef BSP_USING_LPUART4 + + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_00_LPUART4_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_01_LPUART4_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_00_LPUART4_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_01_LPUART4_RX, + 0x10B0u); +#endif +#ifdef BSP_USING_LPUART5 + + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_12_LPUART5_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_13_LPUART5_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_12_LPUART5_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_13_LPUART5_RX, + 0x10B0u); +#endif +#ifdef BSP_USING_LPUART6 + + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_02_LPUART6_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_03_LPUART6_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_02_LPUART6_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_03_LPUART6_RX, + 0x10B0u); +#endif +#ifdef BSP_USING_LPUART7 + + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_31_LPUART7_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_32_LPUART7_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_31_LPUART7_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_32_LPUART7_RX, + 0x10B0u); +#endif +#ifdef BSP_USING_LPUART8 + + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_10_LPUART8_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_11_LPUART8_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_10_LPUART8_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_11_LPUART8_RX, + 0x10B0u); +#endif +} +#endif /* BSP_USING_LPUART */ + +#ifdef BSP_USING_ETH +void imxrt_enet_pins_init(void) +{ + CLOCK_EnableClock(kCLOCK_Iomuxc); /* iomuxc clock (iomuxc_clk_enable): 0x03u */ + + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_09_GPIO1_IO09, /* GPIO_AD_B0_09 is configured as GPIO1_IO09 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_10_GPIO1_IO10, /* GPIO_AD_B0_10 is configured as GPIO1_IO10 */ + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_04_ENET_RX_DATA00, /* GPIO_B1_04 is configured as ENET_RX_DATA00 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_05_ENET_RX_DATA01, /* GPIO_B1_05 is configured as ENET_RX_DATA01 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_06_ENET_RX_EN, /* GPIO_B1_06 is configured as ENET_RX_EN */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_07_ENET_TX_DATA00, /* GPIO_B1_07 is configured as ENET_TX_DATA00 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_08_ENET_TX_DATA01, /* GPIO_B1_08 is configured as ENET_TX_DATA01 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_09_ENET_TX_EN, /* GPIO_B1_09 is configured as ENET_TX_EN */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_10_ENET_REF_CLK, /* GPIO_B1_10 is configured as ENET_REF_CLK */ + 1U); /* Software Input On Field: Force input path of pad GPIO_B1_10 */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_11_ENET_RX_ER, /* GPIO_B1_11 is configured as ENET_RX_ER */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_40_ENET_MDC, /* GPIO_EMC_40 is configured as ENET_MDC */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_41_ENET_MDIO, /* GPIO_EMC_41 is configured as ENET_MDIO */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_09_GPIO1_IO09, /* GPIO_AD_B0_09 PAD functional properties : */ + 0xB0A9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_10_GPIO1_IO10, /* GPIO_AD_B0_10 PAD functional properties : */ + 0xB0A9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_04_ENET_RX_DATA00, /* GPIO_B1_04 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_05_ENET_RX_DATA01, /* GPIO_B1_05 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_06_ENET_RX_EN, /* GPIO_B1_06 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_07_ENET_TX_DATA00, /* GPIO_B1_07 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_08_ENET_TX_DATA01, /* GPIO_B1_08 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_09_ENET_TX_EN, /* GPIO_B1_09 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_10_ENET_REF_CLK, /* GPIO_B1_10 PAD functional properties : */ + 0x31u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/6 + Speed Field: low(50MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Disabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_11_ENET_RX_ER, /* GPIO_B1_11 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_40_ENET_MDC, /* GPIO_EMC_40 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_41_ENET_MDIO, /* GPIO_EMC_41 PAD functional properties : */ + 0xB829u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: low(50MHz) + Open Drain Enable Field: Open Drain Enabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ +} + +void imxrt_enet_phy_reset_by_gpio(void) +{ + gpio_pin_config_t gpio_config = {kGPIO_DigitalOutput, 0, kGPIO_NoIntmode}; + + GPIO_PinInit(GPIO1, 9, &gpio_config); + GPIO_PinInit(GPIO1, 10, &gpio_config); + /* pull up the ENET_INT before RESET. */ + GPIO_WritePinOutput(GPIO1, 10, 1); + GPIO_WritePinOutput(GPIO1, 9, 0); + rt_thread_delay(100); + GPIO_WritePinOutput(GPIO1, 9, 1); +} +#endif /* BSP_USING_ETH */ + /** * This function will initial rt1050 board. */ @@ -121,6 +442,14 @@ void rt_hw_board_init() NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4); SysTick_Config(SystemCoreClock / RT_TICK_PER_SECOND); +#ifdef BSP_USING_LPUART + imxrt_uart_pins_init(); +#endif + +#ifdef BSP_USING_ETH + imxrt_enet_pins_init(); +#endif + #ifdef BSP_USING_DMA imxrt_dma_init(); #endif diff --git a/bsp/imxrt/imxrt1064-nxp-evk/board/board.h b/bsp/imxrt/imxrt1064-nxp-evk/board/board.h index 692569842b..500cc62450 100644 --- a/bsp/imxrt/imxrt1064-nxp-evk/board/board.h +++ b/bsp/imxrt/imxrt1064-nxp-evk/board/board.h @@ -45,5 +45,11 @@ extern int heap_end; void rt_hw_board_init(void); +#ifdef BSP_USING_ETH +void imxrt_enet_pins_init(void); +void imxrt_enet_phy_reset_by_gpio(void); +#define PHY_ADDRESS 0x02u +#endif + #endif diff --git a/bsp/imxrt/imxrt1064-nxp-evk/board/ports/phyksz8081/fsl_phy.c b/bsp/imxrt/imxrt1064-nxp-evk/board/ports/phyksz8081/fsl_phy.c new file mode 100644 index 0000000000..4197514aa5 --- /dev/null +++ b/bsp/imxrt/imxrt1064-nxp-evk/board/ports/phyksz8081/fsl_phy.c @@ -0,0 +1,315 @@ +/* + * Copyright (c) 2015, Freescale Semiconductor, Inc. + * Copyright 2016-2017 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#include "fsl_phy.h" +#include <rtthread.h> +/******************************************************************************* + * Definitions + ******************************************************************************/ + +/*! @brief Defines the timeout macro. */ +#define PHY_TIMEOUT_COUNT 0x3FFFFFFU + +/******************************************************************************* + * Prototypes + ******************************************************************************/ + +/*! + * @brief Get the ENET instance from peripheral base address. + * + * @param base ENET peripheral base address. + * @return ENET instance. + */ +extern uint32_t ENET_GetInstance(ENET_Type *base); + +/******************************************************************************* + * Variables + ******************************************************************************/ + +#if !(defined(FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) && FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) +/*! @brief Pointers to enet clocks for each instance. */ +extern clock_ip_name_t s_enetClock[FSL_FEATURE_SOC_ENET_COUNT]; +#endif /* FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL */ + +/******************************************************************************* + * Code + ******************************************************************************/ + +status_t PHY_Init(ENET_Type *base, uint32_t phyAddr, uint32_t srcClock_Hz) +{ + uint32_t bssReg; + uint32_t counter = PHY_TIMEOUT_COUNT; + uint32_t idReg = 0; + status_t result = kStatus_Success; + uint32_t instance = ENET_GetInstance(base); + uint32_t timeDelay; + uint32_t ctlReg = 0; + +#if !(defined(FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) && FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) + /* Set SMI first. */ + CLOCK_EnableClock(s_enetClock[instance]); +#endif /* FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL */ + ENET_SetSMI(base, srcClock_Hz, false); + + /* Initialization after PHY stars to work. */ + while ((idReg != PHY_CONTROL_ID1) && (counter != 0)) + { + PHY_Read(base, phyAddr, PHY_ID1_REG, &idReg); + counter --; + } + + if (!counter) + { + return kStatus_Fail; + } + + /* Reset PHY. */ + counter = PHY_TIMEOUT_COUNT; + result = PHY_Write(base, phyAddr, PHY_BASICCONTROL_REG, PHY_BCTL_RESET_MASK); + if (result == kStatus_Success) + { + +#if defined(FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE) + uint32_t data = 0; + result = PHY_Read(base, phyAddr, PHY_CONTROL2_REG, &data); + if ( result != kStatus_Success) + { + return result; + } + result = PHY_Write(base, phyAddr, PHY_CONTROL2_REG, (data | PHY_CTL2_REFCLK_SELECT_MASK)); + if (result != kStatus_Success) + { + return result; + } +#endif /* FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE */ + + /* Set the negotiation. */ + result = PHY_Write(base, phyAddr, PHY_AUTONEG_ADVERTISE_REG, + (PHY_100BASETX_FULLDUPLEX_MASK | PHY_100BASETX_HALFDUPLEX_MASK | + PHY_10BASETX_FULLDUPLEX_MASK | PHY_10BASETX_HALFDUPLEX_MASK | 0x1U)); + if (result == kStatus_Success) + { + result = PHY_Write(base, phyAddr, PHY_BASICCONTROL_REG, + (PHY_BCTL_AUTONEG_MASK | PHY_BCTL_RESTART_AUTONEG_MASK)); + if (result == kStatus_Success) + { + /* Check auto negotiation complete. */ + while (counter --) + { + result = PHY_Read(base, phyAddr, PHY_BASICSTATUS_REG, &bssReg); + if ( result == kStatus_Success) + { + PHY_Read(base, phyAddr, PHY_CONTROL1_REG, &ctlReg); + if (((bssReg & PHY_BSTATUS_AUTONEGCOMP_MASK) != 0) && (ctlReg & PHY_LINK_READY_MASK)) + { + /* Wait a moment for Phy status stable. */ + for (timeDelay = 0; timeDelay < PHY_TIMEOUT_COUNT; timeDelay ++) + { + __ASM("nop"); + } + break; + } + } + + if (!counter) + { + return kStatus_PHY_AutoNegotiateFail; + } + } + } + } + } + + return result; +} + +status_t PHY_Write(ENET_Type *base, uint32_t phyAddr, uint32_t phyReg, uint32_t data) +{ + uint32_t counter; + + /* Clear the SMI interrupt event. */ + ENET_ClearInterruptStatus(base, ENET_EIR_MII_MASK); + + /* Starts a SMI write command. */ + ENET_StartSMIWrite(base, phyAddr, phyReg, kENET_MiiWriteValidFrame, data); + + /* Wait for SMI complete. */ + for (counter = PHY_TIMEOUT_COUNT; counter > 0; counter--) + { + if (ENET_GetInterruptStatus(base) & ENET_EIR_MII_MASK) + { + break; + } + } + + /* Check for timeout. */ + if (!counter) + { + return kStatus_PHY_SMIVisitTimeout; + } + + /* Clear MII interrupt event. */ + ENET_ClearInterruptStatus(base, ENET_EIR_MII_MASK); + + return kStatus_Success; +} + +status_t PHY_Read(ENET_Type *base, uint32_t phyAddr, uint32_t phyReg, uint32_t *dataPtr) +{ + assert(dataPtr); + + uint32_t counter; + + /* Clear the MII interrupt event. */ + ENET_ClearInterruptStatus(base, ENET_EIR_MII_MASK); + + /* Starts a SMI read command operation. */ + ENET_StartSMIRead(base, phyAddr, phyReg, kENET_MiiReadValidFrame); + + /* Wait for MII complete. */ + for (counter = PHY_TIMEOUT_COUNT; counter > 0; counter--) + { + if (ENET_GetInterruptStatus(base) & ENET_EIR_MII_MASK) + { + break; + } + } + + /* Check for timeout. */ + if (!counter) + { + return kStatus_PHY_SMIVisitTimeout; + } + + /* Get data from MII register. */ + *dataPtr = ENET_ReadSMIData(base); + + /* Clear MII interrupt event. */ + ENET_ClearInterruptStatus(base, ENET_EIR_MII_MASK); + + return kStatus_Success; +} + +status_t PHY_EnableLoopback(ENET_Type *base, uint32_t phyAddr, phy_loop_t mode, phy_speed_t speed, bool enable) +{ + status_t result; + uint32_t data = 0; + + /* Set the loop mode. */ + if (enable) + { + if (mode == kPHY_LocalLoop) + { + if (speed == kPHY_Speed100M) + { + data = PHY_BCTL_SPEED_100M_MASK | PHY_BCTL_DUPLEX_MASK | PHY_BCTL_LOOP_MASK; + } + else + { + data = PHY_BCTL_DUPLEX_MASK | PHY_BCTL_LOOP_MASK; + } + return PHY_Write(base, phyAddr, PHY_BASICCONTROL_REG, data); + } + else + { + /* First read the current status in control register. */ + result = PHY_Read(base, phyAddr, PHY_CONTROL2_REG, &data); + if (result == kStatus_Success) + { + return PHY_Write(base, phyAddr, PHY_CONTROL2_REG, (data | PHY_CTL2_REMOTELOOP_MASK)); + } + } + } + else + { + /* Disable the loop mode. */ + if (mode == kPHY_LocalLoop) + { + /* First read the current status in control register. */ + result = PHY_Read(base, phyAddr, PHY_BASICCONTROL_REG, &data); + if (result == kStatus_Success) + { + data &= ~PHY_BCTL_LOOP_MASK; + return PHY_Write(base, phyAddr, PHY_BASICCONTROL_REG, (data | PHY_BCTL_RESTART_AUTONEG_MASK)); + } + } + else + { + /* First read the current status in control one register. */ + result = PHY_Read(base, phyAddr, PHY_CONTROL2_REG, &data); + if (result == kStatus_Success) + { + return PHY_Write(base, phyAddr, PHY_CONTROL2_REG, (data & ~PHY_CTL2_REMOTELOOP_MASK)); + } + } + } + return result; +} + +status_t PHY_GetLinkStatus(ENET_Type *base, uint32_t phyAddr, bool *status) +{ + assert(status); + + status_t result = kStatus_Success; + uint32_t data; + + /* Read the basic status register. */ + result = PHY_Read(base, phyAddr, PHY_BASICSTATUS_REG, &data); + if (result == kStatus_Success) + { + if (!(PHY_BSTATUS_LINKSTATUS_MASK & data)) + { + /* link down. */ + *status = false; + } + else + { + /* link up. */ + *status = true; + } + } + return result; +} + +status_t PHY_GetLinkSpeedDuplex(ENET_Type *base, uint32_t phyAddr, phy_speed_t *speed, phy_duplex_t *duplex) +{ + assert(duplex); + + status_t result = kStatus_Success; + uint32_t data, ctlReg; + + /* Read the control two register. */ + result = PHY_Read(base, phyAddr, PHY_CONTROL1_REG, &ctlReg); + if (result == kStatus_Success) + { + data = ctlReg & PHY_CTL1_SPEEDUPLX_MASK; + if ((PHY_CTL1_10FULLDUPLEX_MASK == data) || (PHY_CTL1_100FULLDUPLEX_MASK == data)) + { + /* Full duplex. */ + *duplex = kPHY_FullDuplex; + } + else + { + /* Half duplex. */ + *duplex = kPHY_HalfDuplex; + } + + data = ctlReg & PHY_CTL1_SPEEDUPLX_MASK; + if ((PHY_CTL1_100HALFDUPLEX_MASK == data) || (PHY_CTL1_100FULLDUPLEX_MASK == data)) + { + /* 100M speed. */ + *speed = kPHY_Speed100M; + } + else + { /* 10M speed. */ + *speed = kPHY_Speed10M; + } + } + + return result; +} diff --git a/bsp/imxrt/imxrt1064-nxp-evk/board/ports/phyksz8081/fsl_phy.h b/bsp/imxrt/imxrt1064-nxp-evk/board/ports/phyksz8081/fsl_phy.h new file mode 100644 index 0000000000..a1eff6d723 --- /dev/null +++ b/bsp/imxrt/imxrt1064-nxp-evk/board/ports/phyksz8081/fsl_phy.h @@ -0,0 +1,200 @@ +/* + * Copyright (c) 2015, Freescale Semiconductor, Inc. + * Copyright 2016-2017 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ +#ifndef _FSL_PHY_H_ +#define _FSL_PHY_H_ + +#include "fsl_enet.h" + +/*! + * @addtogroup phy_driver + * @{ + */ + +/******************************************************************************* + * Definitions + ******************************************************************************/ + +/*! @brief PHY driver version */ +#define FSL_PHY_DRIVER_VERSION (MAKE_VERSION(2, 0, 0)) /*!< Version 2.0.0. */ + +/*! @brief Defines the PHY registers. */ +#define PHY_BASICCONTROL_REG 0x00U /*!< The PHY basic control register. */ +#define PHY_BASICSTATUS_REG 0x01U /*!< The PHY basic status register. */ +#define PHY_ID1_REG 0x02U /*!< The PHY ID one register. */ +#define PHY_ID2_REG 0x03U /*!< The PHY ID two register. */ +#define PHY_AUTONEG_ADVERTISE_REG 0x04U /*!< The PHY auto-negotiate advertise register. */ +#define PHY_CONTROL1_REG 0x1EU /*!< The PHY control one register. */ +#define PHY_CONTROL2_REG 0x1FU /*!< The PHY control two register. */ + +#define PHY_CONTROL_ID1 0x22U /*!< The PHY ID1*/ + +/*! @brief Defines the mask flag in basic control register. */ +#define PHY_BCTL_DUPLEX_MASK 0x0100U /*!< The PHY duplex bit mask. */ +#define PHY_BCTL_RESTART_AUTONEG_MASK 0x0200U /*!< The PHY restart auto negotiation mask. */ +#define PHY_BCTL_AUTONEG_MASK 0x1000U /*!< The PHY auto negotiation bit mask. */ +#define PHY_BCTL_SPEED_MASK 0x2000U /*!< The PHY speed bit mask. */ +#define PHY_BCTL_LOOP_MASK 0x4000U /*!< The PHY loop bit mask. */ +#define PHY_BCTL_RESET_MASK 0x8000U /*!< The PHY reset bit mask. */ +#define PHY_BCTL_SPEED_100M_MASK 0x2000U /*!< The PHY 100M speed mask. */ + +/*!@brief Defines the mask flag of operation mode in control two register*/ +#define PHY_CTL2_REMOTELOOP_MASK 0x0004U /*!< The PHY remote loopback mask. */ +#define PHY_CTL2_REFCLK_SELECT_MASK 0x0080U /*!< The PHY RMII reference clock select. */ +#define PHY_CTL1_10HALFDUPLEX_MASK 0x0001U /*!< The PHY 10M half duplex mask. */ +#define PHY_CTL1_100HALFDUPLEX_MASK 0x0002U /*!< The PHY 100M half duplex mask. */ +#define PHY_CTL1_10FULLDUPLEX_MASK 0x0005U /*!< The PHY 10M full duplex mask. */ +#define PHY_CTL1_100FULLDUPLEX_MASK 0x0006U /*!< The PHY 100M full duplex mask. */ +#define PHY_CTL1_SPEEDUPLX_MASK 0x0007U /*!< The PHY speed and duplex mask. */ +#define PHY_CTL1_ENERGYDETECT_MASK 0x10U /*!< The PHY signal present on rx differential pair. */ +#define PHY_CTL1_LINKUP_MASK 0x100U /*!< The PHY link up. */ +#define PHY_LINK_READY_MASK (PHY_CTL1_ENERGYDETECT_MASK | PHY_CTL1_LINKUP_MASK) + +/*! @brief Defines the mask flag in basic status register. */ +#define PHY_BSTATUS_LINKSTATUS_MASK 0x0004U /*!< The PHY link status mask. */ +#define PHY_BSTATUS_AUTONEGABLE_MASK 0x0008U /*!< The PHY auto-negotiation ability mask. */ +#define PHY_BSTATUS_AUTONEGCOMP_MASK 0x0020U /*!< The PHY auto-negotiation complete mask. */ + +/*! @brief Defines the mask flag in PHY auto-negotiation advertise register. */ +#define PHY_100BaseT4_ABILITY_MASK 0x200U /*!< The PHY have the T4 ability. */ +#define PHY_100BASETX_FULLDUPLEX_MASK 0x100U /*!< The PHY has the 100M full duplex ability.*/ +#define PHY_100BASETX_HALFDUPLEX_MASK 0x080U /*!< The PHY has the 100M full duplex ability.*/ +#define PHY_10BASETX_FULLDUPLEX_MASK 0x040U /*!< The PHY has the 10M full duplex ability.*/ +#define PHY_10BASETX_HALFDUPLEX_MASK 0x020U /*!< The PHY has the 10M full duplex ability.*/ + +/*! @brief Defines the PHY status. */ +enum _phy_status +{ + kStatus_PHY_SMIVisitTimeout = MAKE_STATUS(kStatusGroup_PHY, 1), /*!< ENET PHY SMI visit timeout. */ + kStatus_PHY_AutoNegotiateFail = MAKE_STATUS(kStatusGroup_PHY, 2) /*!< ENET PHY AutoNegotiate Fail. */ +}; + +/*! @brief Defines the PHY link speed. This is align with the speed for ENET MAC. */ +typedef enum _phy_speed +{ + kPHY_Speed10M = 0U, /*!< ENET PHY 10M speed. */ + kPHY_Speed100M /*!< ENET PHY 100M speed. */ +} phy_speed_t; + +/*! @brief Defines the PHY link duplex. */ +typedef enum _phy_duplex +{ + kPHY_HalfDuplex = 0U, /*!< ENET PHY half duplex. */ + kPHY_FullDuplex /*!< ENET PHY full duplex. */ +} phy_duplex_t; + +/*! @brief Defines the PHY loopback mode. */ +typedef enum _phy_loop +{ + kPHY_LocalLoop = 0U, /*!< ENET PHY local loopback. */ + kPHY_RemoteLoop /*!< ENET PHY remote loopback. */ +} phy_loop_t; + +/******************************************************************************* + * API + ******************************************************************************/ + +#if defined(__cplusplus) +extern "C" { +#endif + +/*! + * @name PHY Driver + * @{ + */ + +/*! + * @brief Initializes PHY. + * + * This function initialize the SMI interface and initialize PHY. + * The SMI is the MII management interface between PHY and MAC, which should be + * firstly initialized before any other operation for PHY. The PHY initialize with auto-negotiation. + * + * @param base ENET peripheral base address. + * @param phyAddr The PHY address. + * @param srcClock_Hz The module clock frequency - system clock for MII management interface - SMI. + * @retval kStatus_Success PHY initialize success + * @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out + * @retval kStatus_PHY_AutoNegotiateFail PHY auto negotiate fail + */ +status_t PHY_Init(ENET_Type *base, uint32_t phyAddr, uint32_t srcClock_Hz); + +/*! + * @brief PHY Write function. This function write data over the SMI to + * the specified PHY register. This function is called by all PHY interfaces. + * + * @param base ENET peripheral base address. + * @param phyAddr The PHY address. + * @param phyReg The PHY register. + * @param data The data written to the PHY register. + * @retval kStatus_Success PHY write success + * @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out + */ +status_t PHY_Write(ENET_Type *base, uint32_t phyAddr, uint32_t phyReg, uint32_t data); + +/*! + * @brief PHY Read function. This interface read data over the SMI from the + * specified PHY register. This function is called by all PHY interfaces. + * + * @param base ENET peripheral base address. + * @param phyAddr The PHY address. + * @param phyReg The PHY register. + * @param dataPtr The address to store the data read from the PHY register. + * @retval kStatus_Success PHY read success + * @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out + */ +status_t PHY_Read(ENET_Type *base, uint32_t phyAddr, uint32_t phyReg, uint32_t *dataPtr); + +/*! + * @brief Enables/disables PHY loopback. + * + * @param base ENET peripheral base address. + * @param phyAddr The PHY address. + * @param mode The loopback mode to be enabled, please see "phy_loop_t". + * the two loopback mode should not be both set. when one loopback mode is set + * the other one should be disabled. + * @param speed PHY speed for loopback mode. + * @param enable True to enable, false to disable. + * @retval kStatus_Success PHY loopback success + * @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out + */ +status_t PHY_EnableLoopback(ENET_Type *base, uint32_t phyAddr, phy_loop_t mode, phy_speed_t speed, bool enable); + +/*! + * @brief Gets the PHY link status. + * + * @param base ENET peripheral base address. + * @param phyAddr The PHY address. + * @param status The link up or down status of the PHY. + * - true the link is up. + * - false the link is down. + * @retval kStatus_Success PHY get link status success + * @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out + */ +status_t PHY_GetLinkStatus(ENET_Type *base, uint32_t phyAddr, bool *status); + +/*! + * @brief Gets the PHY link speed and duplex. + * + * @param base ENET peripheral base address. + * @param phyAddr The PHY address. + * @param speed The address of PHY link speed. + * @param duplex The link duplex of PHY. + * @retval kStatus_Success PHY get link speed and duplex success + * @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out + */ +status_t PHY_GetLinkSpeedDuplex(ENET_Type *base, uint32_t phyAddr, phy_speed_t *speed, phy_duplex_t *duplex); + +/* @} */ + +#if defined(__cplusplus) +} +#endif + +/*! @}*/ + +#endif /* _FSL_PHY_H_ */ diff --git a/bsp/imxrt/imxrt1064-nxp-evk/board/ports/sdram_port.h b/bsp/imxrt/imxrt1064-nxp-evk/board/ports/sdram_port.h new file mode 100644 index 0000000000..477987b4e7 --- /dev/null +++ b/bsp/imxrt/imxrt1064-nxp-evk/board/ports/sdram_port.h @@ -0,0 +1,49 @@ +/* + * Copyright (c) 2006-2018, RT-Thread Development Team + * + * SPDX-License-Identifier: Apache-2.0 + * + * Change Logs: + * Date Author Notes + * 2018-12-05 zylx The first version for STM32F4xx + * 2019-4-25 misonyo port to IMXRT + */ + +#ifndef SDRAM_PORT_H__ +#define SDRAM_PORT_H__ + +/* parameters for sdram peripheral */ + +#define SDRAM_BANK_ADDR ((uint32_t)0x80000000U) +/* region#0/1/2/3: kSEMC_SDRAM_CS0/1/2/3 */ +#define SDRAM_REGION kSEMC_SDRAM_CS0 +/* CS pin: kSEMC_MUXCSX0/1/2/3 */ +#define SDRAM_CS_PIN kSEMC_MUXCSX0 +/* size(kbyte):32MB = 32*1024*1KBytes */ +#define SDRAM_SIZE ((uint32_t)0x8000) +/* data width: kSEMC_PortSize8Bit,kSEMC_PortSize16Bit */ +#define SDRAM_DATA_WIDTH kSEMC_PortSize16Bit +/* column bit numbers: kSEMC_SdramColunm_9/10/11/12bit */ +#define SDRAM_COLUMN_BITS kSEMC_SdramColunm_9bit +/* cas latency clock number: kSEMC_LatencyOne/Two/Three */ +#define SDRAM_CAS_LATENCY kSEMC_LatencyThree + +/* Timing configuration for W9825G6KH */ +/* TRP:precharge to active command time (ns) */ +#define SDRAM_TRP 18 +/* TRCD:active to read/write command delay time (ns) */ +#define SDRAM_TRCD 18 +/* The time between two refresh commands,Use the maximum of the (Trfc , Txsr).(ns) */ +#define SDRAM_REFRESH_RECOVERY 67 +/* TWR:write recovery time (ns). */ +#define SDRAM_TWR 12 +/* TRAS:active to precharge command time (ns). */ +#define SDRAM_TRAS 42 +/* TRC time (ns). */ +#define SDRAM_TRC 60 +/* active to active time (ns). */ +#define SDRAM_ACT2ACT 60 +/* refresh time (ns). 64ms */ +#define SDRAM_REFRESH_ROW 64 * 1000000 / 8192 + +#endif /* SDRAM_PORT_H__ */ diff --git a/bsp/imxrt/imxrt1064-nxp-evk/rtconfig.py b/bsp/imxrt/imxrt1064-nxp-evk/rtconfig.py index eeef72b0c6..9689ac0bcb 100644 --- a/bsp/imxrt/imxrt1064-nxp-evk/rtconfig.py +++ b/bsp/imxrt/imxrt1064-nxp-evk/rtconfig.py @@ -48,7 +48,7 @@ if PLATFORM == 'gcc': DEVICE = ' -mcpu=' + CPU + ' -mthumb -mfpu=fpv5-d16 -mfloat-abi=hard -ffunction-sections -fdata-sections' CFLAGS = DEVICE + ' -Wall -D__FPU_PRESENT -eentry' AFLAGS = ' -c' + DEVICE + ' -x assembler-with-cpp -Wa,-mimplicit-it=thumb -D__START=entry' - LFLAGS = DEVICE + ' -lm -lgcc -lc' + ' -nostartfiles -Wl,--gc-sections,-Map=rtthread.map,-cref,-u,Reset_Handler -T board/linker_scripts/link.lds' + LFLAGS = DEVICE + ' -lm -lgcc -lc' + ' -nostartfiles -Wl,--gc-sections,-Map=rtthread.map,-cref,-u,Reset_Handler -T board/linker_scripts/link.lds -Xlinker -print-memory-usage' CPATH = '' LPATH = '' @@ -57,8 +57,8 @@ if PLATFORM == 'gcc': AFLAGS += ' -D__STARTUP_CLEAR_BSS' if BUILD == 'debug': - CFLAGS += ' -gdwarf-2' - AFLAGS += ' -gdwarf-2' + CFLAGS += ' -g' + AFLAGS += ' -g' CFLAGS += ' -O0' else: CFLAGS += ' -O2 -Os' |