| Age | Commit message (Collapse) | Author |
|---|
|
15.2 (#11870)
* [bsp][esp32] adapt C3/C6 to ESP-IDF v6.1 and bump RISC-V toolchain to gcc 15.2
- Adapt ESP32-C3/C6 BSP to ESP-IDF v6.1; bump RISC-V toolchain to gcc 15.2
- C6: re-enable SPI with board-local drv_spi.c; add devices.spi to CI
attachconfig; drop shared drv_spi.c spi_command_t hack
- C6: fix ADC oneshot multi-channel unit handle and mutex
- C3: fix portTRY_ENTER_CRITICAL_SAFE expansion in portmacro.h
- Compat with RT-Thread-packages/esp-idf rtt-dev used by CI: map
SYSTIMER_* to SYSTIMER_LL_* (C3 and C6 board.c), accept uart_periph.h
from hal/ or soc/
- Fix clang-format and cppcheck issues in the compat code
Signed-off-by: seteiro <[email protected]>
Co-Authored-By: Grok <[email protected]>
* ci: retrigger after esp-idf#18 merged
* bsp: ESP: fix C6 ADC for IDF 6.1 (adc_ll bus clock)
Replace removed PERIPH_SARADC_MODULE with adc_ll_enable_bus_clock /
adc_ll_reset_register when ESP_IDF_VERSION >= 6.0.0.
---------
Signed-off-by: seteiro <[email protected]>
Co-authored-by: Grok <[email protected]>
|
|
* [bsp][esp32-c6] add ESP32-C6-DevKitC-1 support
Add bsp/ESP/ESP32_C6. Default image is GPIO, UART0 and ADC. The C6 IDF sources are not in RT-Thread-packages/esp-idf yet.
* [bsp][esp32-c6] fix CI format, C6 package and CH32V203 D6 build
clang-format the files the format check rejected. Fetch the C6 scons
branch when the downloaded ESP-IDF package has no C6 target. Patch the
CH32V20x SDK under libraries so a D6 build no longer calls Exit().
* [bsp][esp32-c6] fetch mbedtls and stop pkgs from pulling the C6 branch
* [bsp][esp32-c6] rebuild CI against the package branch tip
* [bsp][esp32-c6] rebuild CI against the strict-mode package tip
* [bsp][esp32-c6] fix the reviewed ADC, math and package pin bugs
Keep the IDF tree on the reviewed commit, and stop the ADC and critical-section paths from reporting success when they did not.
* [bsp][esp32-c6] reserve stuck interrupt lines and lock ADC
CPU lines 3 and 4 never latch an enable, so copying the handler left the non-IRAM mask on the old line. Reserve those lines and let the allocator write the mask and the route together. The C6 oneshot registers are shared, so one mutex covers enable and convert.
* [bsp][esp32-c6] list the peripherals this board actually runs
GPIO, UART0 and ADC1 have been read on the DevKitC-1. Radios and the untested buses stay marked unsupported.
* [bsp][esp32-c6] keep SPI unsupported after the loopback mismatch
GPIO7 shorted to GPIO2 returned 0xA5000000 for a sent 0xA5, so the table does not mark SPI supported.
---------
Co-authored-by: seteiro <[email protected]>
|
|
|
|
- libraries/N32_Drivers: add ADC/DAC/I2C/SPI config headers for the
h47x_48x, h49x and h7xx series, and extend the shared drivers
(adc, dac, eth, gpio, hard_i2c, nand, qspi, sdram, spi, usart, wdt).
- n32h487zgl7-evb / n32h497zgl7-evb: add board ports (femc_timing,
phy_reset, usb_config) and update Kconfig, SConscript, rtconfig and
the IAR/Keil project files.
- n32h760zil7-stb: update Kconfig and rtconfig.
- CI: register the three n32hxxx boards.
|
|
* [bsp][stm32] Add stm32n657-st-nucleo BSP
* style: format STM32 HAL drivers and STM32N657 BSP with clang-format
|
|
|
|
|
|
|
|
|
|
|
|
* ci: add armclang BSP build coverage
* components/libc: avoid armclang errno include recursion
|
|
|
|
|
|
|
|
|
|
- add i686-atxhua-picolib-elf-gcc toolchain
- add picolib option to bsp/x86
- add necessary picolib require library
|
|
* add i686 x86 newlib toolchain
* add missing x86 gcc option to manual_dist.yml
* fix typo
|
|
|
|
|
|
(#10314)
ci: Replace the judgment file modification mechanism of bsp_building.yml and incorporate the PR status show into bsp_building.yml
|
|
|
|
[action/ci] add qemu-pre-build-and-post-build for RT_SMART build
|
|
* [action/ci] 把每次编译结果上传到github
* [fix]
* add output
* fix
* fixthe attach_file_name
* fix
* fix name
* [action] 更新一下toolchain的版本号
* [bsp/stm32] hex 生成
* Update type.h
|
|
* [github/action] 添加scons显示编译时间的命令
* [bsp/pico] 删除ci 耗时的config，在F412中已验证
* [bsp/f412] 这个编译需要3分钟，不合理，先从ci中删除
|
|
* [action/ci] pkgs --update-force instead of pkgs --update
* Update bsp_buildings.yml
* l4 单独拉出来
|
|
|
|
|
|
|
|
|
|
|
|
* [action] add toolchain install script
|
|
* [action][cppcheck] add summary
添加summary 方便查看出错信息
|
|
'--check-level=exhaustive'
这个选项可以更深入的在分支中检测，但是会耗时比较久一些。
|
|
* [script] add install.sh for rt-thread
* [install] add gitee chevk
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* [src] add rt_hw_cpu_id() wrapper API
rt_hw_cpu_id() is an unsafe API which should not be used by most codes
directly. It's error-prone because it must be used in proper context,
otherwise it can lead to errors and unpredictable behavior.
This patch adds a wrapper API for rt_hw_cpu_id() to address this risk.
It includes the context-checking functionality and provides a safer
alternative for obtaining CPU IDs, ensuring that it is used correctly
within the appropriate context.
Signed-off-by: Shell <[email protected]>
* fixup UMP
* update API & comment
* ci: cpp_check
---------
Signed-off-by: Shell <[email protected]>
|
|
Signed-off-by: Shell <[email protected]>
|
|
Signed-off-by: xqyjlj <[email protected]>
Signed-off-by: Shell <[email protected]>
Co-authored-by: xqyjlj <[email protected]>
|
|
|
|
|
|
|
|
|
|
|
|
|
