1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
|
/**************************************************************************//**
* @file
* @brief Operational Amplifier (OPAMP) peripheral API
* @author Energy Micro AS
* @version 3.0.0
******************************************************************************
* @section License
* <b>(C) Copyright 2012 Energy Micro AS, http://www.energymicro.com</b>
*******************************************************************************
*
* Permission is granted to anyone to use this software for any purpose,
* including commercial applications, and to alter it and redistribute it
* freely, subject to the following restrictions:
*
* 1. The origin of this software must not be misrepresented; you must not
* claim that you wrote the original software.
* 2. Altered source versions must be plainly marked as such, and must not be
* misrepresented as being the original software.
* 3. This notice may not be removed or altered from any source distribution.
*
* DISCLAIMER OF WARRANTY/LIMITATION OF REMEDIES: Energy Micro AS has no
* obligation to support this Software. Energy Micro AS is providing the
* Software "AS IS", with no express or implied warranties of any kind,
* including, but not limited to, any implied warranties of merchantability
* or fitness for any particular purpose or warranties against infringement
* of any proprietary rights of a third party.
*
* Energy Micro AS will not be liable for any consequential, incidental, or
* special damages, or any other relief, or for any claim by any third party,
* arising from your use of this Software.
*
*****************************************************************************/
#ifndef __EM_OPAMP_H
#define __EM_OPAMP_H
#include "em_part.h"
#if defined(OPAMP_PRESENT) && (OPAMP_COUNT == 1)
#ifdef __cplusplus
extern "C" {
#endif
#include <stdint.h>
#include <stdbool.h>
#include "em_dac.h"
/***************************************************************************//**
* @addtogroup EM_Library
* @{
******************************************************************************/
/***************************************************************************//**
* @addtogroup OPAMP
* @{
******************************************************************************/
/** @cond DO_NOT_INCLUDE_WITH_DOXYGEN */
/** Validation of DAC OPA number for assert statements. */
#define DAC_OPA_VALID(opa) ((opa) <= OPA2)
/** @endcond */
/*******************************************************************************
******************************** ENUMS ************************************
******************************************************************************/
/** OPAMP selector values. */
typedef enum
{
OPA0 = 0, /**< Select OPA0. */
OPA1 = 1, /**< Select OPA1. */
OPA2 = 2 /**< Select OPA2. */
} OPAMP_TypeDef;
/** OPAMP negative terminal input selection values. */
typedef enum
{
opaNegSelDisable = DAC_OPA0MUX_NEGSEL_DISABLE, /**< Input disabled. */
opaNegSelUnityGain = DAC_OPA0MUX_NEGSEL_UG, /**< Unity gain feedback path. */
opaNegSelResTap = DAC_OPA0MUX_NEGSEL_OPATAP, /**< Feedback resistor ladder tap. */
opaNegSelNegPad = DAC_OPA0MUX_NEGSEL_NEGPAD /**< Negative pad as input. */
} OPAMP_NegSel_TypeDef;
/** OPAMP positive terminal input selection values. */
typedef enum
{
opaPosSelDisable = DAC_OPA0MUX_POSSEL_DISABLE, /**< Input disabled. */
opaPosSelDac = DAC_OPA0MUX_POSSEL_DAC, /**< DAC as input (not OPA2). */
opaPosSelPosPad = DAC_OPA0MUX_POSSEL_POSPAD, /**< Positive pad as input. */
opaPosSelOpaIn = DAC_OPA0MUX_POSSEL_OPA0INP, /**< Input from OPAx. */
opaPosSelResTapOpa0 = DAC_OPA0MUX_POSSEL_OPATAP /**< Feedback resistor ladder tap from OPA0. */
} OPAMP_PosSel_TypeDef;
/** OPAMP output terminal selection values. */
typedef enum
{
opaOutModeDisable = DAC_OPA0MUX_OUTMODE_DISABLE, /**< OPA output disabled. */
opaOutModeMain = DAC_OPA0MUX_OUTMODE_MAIN, /**< Main output to pin enabled. */
opaOutModeAlt = DAC_OPA0MUX_OUTMODE_ALT, /**< Alternate output(s) enabled (not OPA2). */
opaOutModeAll = DAC_OPA0MUX_OUTMODE_ALL /**< Both main and alternate enabled (not OPA2). */
} OPAMP_OutMode_TypeDef;
/** OPAMP gain values. */
typedef enum
{
opaResSelDefault = DAC_OPA0MUX_RESSEL_DEFAULT, /**< Default value when resistor ladder is unused. */
opaResSelR2eq0_33R1 = DAC_OPA0MUX_RESSEL_RES0, /**< R2 = 0.33 * R1 */
opaResSelR2eqR1 = DAC_OPA0MUX_RESSEL_RES1, /**< R2 = R1 */
opaResSelR1eq1_67R1 = DAC_OPA0MUX_RESSEL_RES2, /**< R2 = 1.67 R1 */
opaResSelR2eq2R1 = DAC_OPA0MUX_RESSEL_RES3, /**< R2 = 2 * R1 */
opaResSelR2eq3R1 = DAC_OPA0MUX_RESSEL_RES4, /**< R2 = 3 * R1 */
opaResSelR2eq4_33R1 = DAC_OPA0MUX_RESSEL_RES5, /**< R2 = 4.33 * R1 */
opaResSelR2eq7R1 = DAC_OPA0MUX_RESSEL_RES6, /**< R2 = 7 * R1 */
opaResSelR2eq15R1 = DAC_OPA0MUX_RESSEL_RES7 /**< R2 = 15 * R1 */
} OPAMP_ResSel_TypeDef;
/** OPAMP resistor ladder input selector values. */
typedef enum
{
opaResInMuxDisable = DAC_OPA0MUX_RESINMUX_DISABLE, /**< Resistor ladder disabled. */
opaResInMuxOpaIn = DAC_OPA0MUX_RESINMUX_OPA0INP, /**< Input from OPAx. */
opaResInMuxNegPad = DAC_OPA0MUX_RESINMUX_NEGPAD, /**< Input from negative pad. */
opaResInMuxPosPad = DAC_OPA0MUX_RESINMUX_POSPAD, /**< Input from positive pad. */
opaResInMuxVss = DAC_OPA0MUX_RESINMUX_VSS /**< Input connected to Vss. */
} OPAMP_ResInMux_TypeDef;
/*******************************************************************************
******************************* STRUCTS ***********************************
******************************************************************************/
/** OPAMP init structure. */
typedef struct
{
OPAMP_NegSel_TypeDef negSel; /**< Select input source for negative terminal. */
OPAMP_PosSel_TypeDef posSel; /**< Select input source for positive terminal. */
OPAMP_OutMode_TypeDef outMode; /**< Output terminal connection. */
OPAMP_ResSel_TypeDef resSel; /**< Select R2/R1 resistor ratio. */
OPAMP_ResInMux_TypeDef resInMux; /**< Select input source for resistor ladder. */
uint32_t outPen; /**< Select alternate output terminal connections. */
uint32_t bias; /**< Set OPAMP bias current. */
bool halfBias; /**< Divide OPAMP bias current by 2. */
bool lpfPosPadDisable; /**< Disable low pass filter on positive pad. */
bool lpfNegPadDisable; /**< Disable low pass filter on negative pad. */
bool nextOut; /**< Enable NEXTOUT signal source. */
bool npEn; /**< Enable positive pad. */
bool ppEn; /**< Enable negative pad. */
bool shortInputs; /**< Short OPAMP input terminals. */
bool hcmDisable; /**< Disable input rail-to-rail capability. */
bool defaultOffset; /**< Use factory calibrated opamp offset value. */
uint32_t offset; /**< Opamp offset value when @ref defaultOffset is false.*/
} OPAMP_Init_TypeDef;
/** Configuration of OPA0/1 in unity gain voltage follower mode. */
#define OPA_INIT_UNITY_GAIN \
{ \
opaNegSelUnityGain, /* Unity gain. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeMain, /* Main output enabled. */ \
opaResSelDefault, /* Resistor ladder is not used. */ \
opaResInMuxDisable, /* Resistor ladder disabled. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
false, /* No nextout output enabled. */ \
false, /* Neg pad disabled. */ \
true, /* Pos pad enabled, used as signal input. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA2 in unity gain voltage follower mode. */
#define OPA_INIT_UNITY_GAIN_OPA2 \
{ \
opaNegSelUnityGain, /* Unity gain. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeMain, /* Main output enabled. */ \
opaResSelDefault, /* Resistor ladder is not used. */ \
opaResInMuxDisable, /* Resistor ladder disabled. */ \
DAC_OPA0MUX_OUTPEN_OUT0, /* Alternate output 0 enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
false, /* No nextout output enabled. */ \
false, /* Neg pad disabled. */ \
true, /* Pos pad enabled, used as signal input. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA0/1 in non-inverting amplifier mode. */
#define OPA_INIT_NON_INVERTING \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeMain, /* Main output enabled. */ \
opaResSelR2eq0_33R1, /* R2 = 1/3 R1 */ \
opaResInMuxNegPad, /* Resistor ladder input from neg pad. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
false, /* No nextout output enabled. */ \
true, /* Neg pad enabled, used as signal ground. */ \
true, /* Pos pad enabled, used as signal input. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA2 in non-inverting amplifier mode. */
#define OPA_INIT_NON_INVERTING_OPA2 \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeMain, /* Main output enabled. */ \
opaResSelR2eq0_33R1, /* R2 = 1/3 R1 */ \
opaResInMuxNegPad, /* Resistor ladder input from neg pad. */ \
DAC_OPA0MUX_OUTPEN_OUT0, /* Alternate output 0 enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
false, /* No nextout output enabled. */ \
true, /* Neg pad enabled, used as signal ground. */ \
true, /* Pos pad enabled, used as signal input. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA0/1 in inverting amplifier mode. */
#define OPA_INIT_INVERTING \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeMain, /* Main output enabled. */ \
opaResSelR2eqR1, /* R2 = R1 */ \
opaResInMuxNegPad, /* Resistor ladder input from neg pad. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
false, /* No nextout output enabled. */ \
true, /* Neg pad enabled, used as signal input. */ \
true, /* Pos pad enabled, used as signal ground. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA2 in inverting amplifier mode. */
#define OPA_INIT_INVERTING_OPA2 \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeMain, /* Main output enabled. */ \
opaResSelR2eqR1, /* R2 = R1 */ \
opaResInMuxNegPad, /* Resistor ladder input from neg pad. */ \
DAC_OPA0MUX_OUTPEN_OUT0, /* Alternate output 0 enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
false, /* No nextout output enabled. */ \
true, /* Neg pad enabled, used as signal input. */ \
true, /* Pos pad enabled, used as signal ground. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA0 in cascaded non-inverting amplifier mode. */
#define OPA_INIT_CASCADED_NON_INVERTING_OPA0 \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeAll, /* Both main and alternate outputs. */ \
opaResSelR2eq0_33R1, /* R2 = 1/3 R1 */ \
opaResInMuxNegPad, /* Resistor ladder input from neg pad. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
true, /* Pass output to next stage (OPA1). */ \
true, /* Neg pad enabled, used as signal ground. */ \
true, /* Pos pad enabled, used as signal input. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA1 in cascaded non-inverting amplifier mode. */
#define OPA_INIT_CASCADED_NON_INVERTING_OPA1 \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelOpaIn, /* Pos input from OPA0 output. */ \
opaOutModeAll, /* Both main and alternate outputs. */ \
opaResSelR2eq0_33R1, /* R2 = 1/3 R1 */ \
opaResInMuxNegPad, /* Resistor ladder input from neg pad. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
true, /* Pass output to next stage (OPA2). */ \
true, /* Neg pad enabled, used as signal ground. */ \
false, /* Pos pad disabled. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA2 in cascaded non-inverting amplifier mode. */
#define OPA_INIT_CASCADED_NON_INVERTING_OPA2 \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelOpaIn, /* Pos input from OPA1 output. */ \
opaOutModeMain, /* Main output enabled. */ \
opaResSelR2eq0_33R1, /* R2 = 1/3 R1 */ \
opaResInMuxNegPad, /* Resistor ladder input from neg pad. */ \
DAC_OPA0MUX_OUTPEN_OUT0, /* Alternate output 0 enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
false, /* No nextout output enabled. */ \
true, /* Neg pad enabled, used as signal ground. */ \
false, /* Pos pad disabled. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA0 in cascaded inverting amplifier mode. */
#define OPA_INIT_CASCADED_INVERTING_OPA0 \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeAll, /* Both main and alternate outputs. */ \
opaResSelR2eqR1, /* R2 = R1 */ \
opaResInMuxNegPad, /* Resistor ladder input from neg pad. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
true, /* Pass output to next stage (OPA1). */ \
true, /* Neg pad enabled, used as signal input. */ \
true, /* Pos pad enabled, used as signal ground. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA1 in cascaded inverting amplifier mode. */
#define OPA_INIT_CASCADED_INVERTING_OPA1 \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeAll, /* Both main and alternate outputs. */ \
opaResSelR2eqR1, /* R2 = R1 */ \
opaResInMuxOpaIn, /* Resistor ladder input from OPA0. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
true, /* Pass output to next stage (OPA2). */ \
false, /* Neg pad disabled. */ \
true, /* Pos pad enabled, used as signal ground. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA2 in cascaded inverting amplifier mode. */
#define OPA_INIT_CASCADED_INVERTING_OPA2 \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeMain, /* Main output enabled. */ \
opaResSelR2eqR1, /* R2 = R1 */ \
opaResInMuxOpaIn, /* Resistor ladder input from OPA1. */ \
DAC_OPA0MUX_OUTPEN_OUT0, /* Alternate output 0 enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
false, /* No nextout output enabled. */ \
false, /* Neg pad disabled. */ \
true, /* Pos pad enabled, used as signal ground. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA0 in two-opamp differential driver mode. */
#define OPA_INIT_DIFF_DRIVER_OPA0 \
{ \
opaNegSelUnityGain, /* Unity gain. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeAll, /* Both main and alternate outputs. */ \
opaResSelDefault, /* Resistor ladder is not used. */ \
opaResInMuxDisable, /* Resistor ladder disabled. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
true, /* Pass output to next stage (OPA1). */ \
false, /* Neg pad disabled. */ \
true, /* Pos pad enabled, used as signal input. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA1 in two-opamp differential driver mode. */
#define OPA_INIT_DIFF_DRIVER_OPA1 \
{ \
opaNegSelResTap, /* Neg input from resistor ladder tap. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeMain, /* Main output enabled. */ \
opaResSelR2eqR1, /* R2 = R1 */ \
opaResInMuxOpaIn, /* Resistor ladder input from OPA0. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
false, /* No nextout output enabled. */ \
false, /* Neg pad disabled. */ \
true, /* Pos pad enabled, used as signal ground. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA0 in three-opamp differential receiver mode. */
#define OPA_INIT_DIFF_RECEIVER_OPA0 \
{ \
opaNegSelUnityGain, /* Unity gain. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeAll, /* Both main and alternate outputs. */ \
opaResSelR2eqR1, /* R2 = R1 */ \
opaResInMuxNegPad, /* Resistor ladder input from neg pad. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
true, /* Pass output to next stage (OPA2). */ \
true, /* Neg pad enabled, used as signal ground. */ \
true, /* Pos pad enabled, used as signal input. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA1 in three-opamp differential receiver mode. */
#define OPA_INIT_DIFF_RECEIVER_OPA1 \
{ \
opaNegSelUnityGain, /* Unity gain. */ \
opaPosSelPosPad, /* Pos input from pad. */ \
opaOutModeAll, /* Both main and alternate outputs. */ \
opaResSelDefault, /* Resistor ladder is not used. */ \
opaResInMuxDisable, /* Disable resistor ladder. */ \
0, /* No alternate outputs enabled. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
true, /* Pass output to next stage (OPA2). */ \
false, /* Neg pad disabled. */ \
true, /* Pos pad enabled, used as signal input. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/** Configuration of OPA2 in three-opamp differential receiver mode. */
#define OPA_INIT_DIFF_RECEIVER_OPA2 \
{ \
opaNegSelResTap, /* Input from resistor ladder tap. */ \
opaPosSelResTapOpa0, /* Input from OPA0 resistor ladder tap. */ \
opaOutModeMain, /* Main output enabled. */ \
opaResSelR2eqR1, /* R2 = R1 */ \
opaResInMuxOpaIn, /* Resistor ladder input from OPA1. */ \
DAC_OPA0MUX_OUTPEN_OUT0, /* Enable alternate output 0. */ \
_DAC_BIASPROG_BIASPROG_DEFAULT, /* Default bias setting. */ \
_DAC_BIASPROG_HALFBIAS_DEFAULT, /* Default half-bias setting. */ \
false, /* No low pass filter on pos pad. */ \
false, /* No low pass filter on neg pad. */ \
false, /* No nextout output enabled. */ \
false, /* Neg pad disabled. */ \
false, /* Pos pad disabled. */ \
false, /* No shorting of inputs. */ \
false, /* Rail-to-rail input enabled. */ \
true, /* Use factory calibrated opamp offset. */ \
0 /* Opamp offset value (not used). */ \
}
/*******************************************************************************
***************************** PROTOTYPES **********************************
******************************************************************************/
void OPAMP_Disable(DAC_TypeDef *dac, OPAMP_TypeDef opa);
void OPAMP_Enable(DAC_TypeDef *dac, OPAMP_TypeDef opa, const OPAMP_Init_TypeDef *init);
/** @} (end addtogroup OPAMP) */
/** @} (end addtogroup EM_Library) */
#ifdef __cplusplus
}
#endif
#endif /* defined( OPAMP_PRESENT ) && ( OPAMP_COUNT == 1 ) */
#endif /* __EM_DAC_H */
|
