blob: c5443955960139a6b42b7ba6b3a7059e53461161 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
|
menu "Hardware Drivers Config"
menu "On-chip Peripheral Drivers"
menuconfig BSP_USING_UART
bool "Enable UART"
default y
select RT_USING_SERIAL
if BSP_USING_UART
config RT_USING_UART1
bool "Enable UART1"
default y
config RT_USING_UART0
bool "Enable UART0"
default n
endif
menuconfig BSP_USING_SDC
bool "Enable sd controller"
select RT_USING_SDIO
select RT_USING_DFS
select RT_USING_DFS_ELMFAT
default n
if BSP_USING_SDC
config BSP_SDC_DEBUG_PRINT
bool "Enable sd controller debug print"
default n
config BSP_SDC_USE_IRQ
bool "Use interrupt to handle when cmd complete, dma complete"
default n
if BSP_SDC_USE_IRQ
config BSP_SDC_IRQ_CARD_REMOVE
bool "Use interrupt to determine if the card is pulled out"
default n
endif
endif
menuconfig BSP_USING_GMAC
bool "Enable gmac"
default n
select RT_USING_NETDEV
if BSP_USING_GMAC
config BSP_USING_GMAC0
bool "Enable GMAC0"
default y
config BSP_USING_GMAC1
bool "Enable GMAC1"
default n
config RT_LWIP_ETH_PAD_SIZE
int "set lwip ETH_PAD_SIZE"
range 2 256
default 2
config RAW_DATA_PRINT
bool "Enable mac raw data print"
default n
if RAW_DATA_PRINT
config ETH_RX_DUMP
bool "Enable gmac receive raw data print "
default n
config ETH_TX_DUMP
bool "Enable gmac send raw data print "
default n
endif
endif
# menuconfig BSP_USE_QSPI
# bool "Enable Qspi"
# select RT_USING_SFUD
# select RT_SFUD_USING_QSPI
# default n
# if BSP_USE_QSPI
# config BSP_QSPI_DEBUG
# bool "Enable qspi debug print"
# default n
# endif
menuconfig BSP_USE_SPI
bool "Enable Spi"
select RT_USING_SFUD
select RT_SFUD_USING_SPI
select RT_SFUD_USING_SFDP
select RT_SFUD_USING_FLASH_INFO_TABLE
select BSP_USE_GPIO
default n
if BSP_USE_SPI
config BSP_SPI_DEBUG
bool "Enable spi debug print"
default n
endif
menuconfig BSP_USE_GPIO
bool "Enable Gpio"
default n
if BSP_USE_GPIO
config BSP_GPIO_DEBUG
bool "Enable gpio debug print"
default n
endif
menuconfig BSP_USE_CAN
bool "Enable Can"
select RT_USING_CAN
default n
if BSP_USE_CAN
config BSP_USING_CAN0
bool "Enable can0"
default n
config BSP_USING_CAN1
bool "Enable can1"
default n
if BSP_USING_CAN0
config BSP_USING_CAN0_DEBUG
bool "Enable can0 work in loop back"
default n
endif
endif
endmenu
menu "Board extended module Drivers"
endmenu
endmenu
|
