blob: d94757fadabb1e6d134a9977f184828c1d1ccb86 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
|
menu "Hardware Drivers Config"
config BSP_USING_HYPERFLASH
bool
default n
config SOC_MIMXRT1052DVL6B
bool
select SOC_IMXRT1050_SERIES
select BSP_USING_HYPERFLASH
select RT_USING_COMPONENTS_INIT
select RT_USING_USER_MAIN
default y
menu "On-chip Peripheral Drivers"
config BSP_USING_DMA
bool "Enable DMA"
default n
config BSP_USING_GPIO
bool "Enable GPIO"
select RT_USING_PIN
default y
menuconfig BSP_USING_LPUART
bool "Enable UART"
select RT_USING_SERIAL
default y
if BSP_USING_LPUART
config BSP_USING_LPUART1
bool "Enable LPUART1"
default y
config BSP_LPUART1_RX_USING_DMA
bool "Enable LPUART1 RX DMA"
depends on BSP_USING_LPUART1
select BSP_USING_DMA
select RT_SERIAL_USING_DMA
default n
config BSP_LPUART1_RX_DMA_CHANNEL
depends on BSP_LPUART1_RX_USING_DMA
int "Set LPUART1 RX DMA channel (0-32)"
default 0
config BSP_LPUART1_TX_USING_DMA
bool "Enable LPUART1 TX DMA"
depends on BSP_USING_LPUART1
select BSP_USING_DMA
select RT_SERIAL_USING_DMA
default n
config BSP_LPUART1_TX_DMA_CHANNEL
depends on BSP_LPUART1_TX_USING_DMA
int "Set LPUART1 TX DMA channel (0-32)"
default 1
config BSP_USING_LPUART3
bool "Enable LPUART3"
default n
config BSP_LPUART3_RX_USING_DMA
bool "Enable LPUART3 RX DMA"
depends on BSP_USING_LPUART3
select BSP_USING_DMA
select RT_SERIAL_USING_DMA
default n
config BSP_LPUART3_RX_DMA_CHANNEL
depends on BSP_LPUART3_RX_USING_DMA
int "Set LPUART3 RX DMA channel (0-32)"
default 0
config BSP_LPUART3_TX_USING_DMA
bool "Enable LPUART3 TX DMA"
depends on BSP_USING_LPUART3
select BSP_USING_DMA
select RT_SERIAL_USING_DMA
default n
config BSP_LPUART3_TX_DMA_CHANNEL
depends on BSP_LPUART3_TX_USING_DMA
int "Set LPUART3 TX DMA channel (0-32)"
default 1
endif
menuconfig BSP_USING_I2C
bool "Enable I2C"
select RT_USING_I2C
default n
if BSP_USING_I2C
config BSP_USING_I2C1
bool "Enable I2C1"
default n
choice HW_I2C1_BADURATE_SEL
prompt "Select I2C1 badurate"
default HW_I2C1_BADURATE_100kHZ
config HW_I2C1_BADURATE_100kHZ
bool "Badurate 100kHZ"
config HW_I2C1_BADURATE_400kHZ
bool "Badurate 400kHZ"
endchoice
endif
endmenu
menu "Onboard Peripheral Drivers"
config BSP_USING_SDRAM
bool "Enable SDRAM"
default n
menuconfig BSP_USING_ETH
bool "Enable Ethernet"
select RT_USING_NETDEV
select RT_USING_LWIP
default n
if BSP_USING_ETH
config BSP_USING_PHY
select RT_USING_PHY
bool "Enable ethernet phy"
default y
if BSP_USING_PHY
config PHY_DEVICE_ADDRESS
int "Specify address of phy device"
default 2
config PHY_USING_KSZ8081
bool "i.MX RT1052EVK uses ksz8081 phy"
default y
if PHY_USING_KSZ8081
config PHY_RESET_PORT
int "indicate port of reset"
default 1
config PHY_RESET_PIN
int "indicate pin of reset"
default 9
config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE
bool "Enable the PHY ksz8081 RMII50M mode"
depends on PHY_USING_KSZ8081
default y
endif
endif
endif
menuconfig BSP_USING_AUDIO
bool "Enable AUDIO (WM8960)"
select BSP_USING_I2C1
select RT_USING_AUDIO
default n
if BSP_USING_AUDIO
config BSP_USING_AUDIO_PLAY
bool "Enable Audio Play"
default y
if BSP_USING_AUDIO_PLAY
config BSP_AUDIO_USING_DMA
bool "Enable AUDIO DMA"
default y
endif
config BSP_USING_AUDIO_RECORD
bool "Enable Audio Record"
select BSP_USING_AUDIO_PLAY
default n
if BSP_USING_AUDIO_RECORD
config BSP_AUDIO_USING_DMA
bool "Enable AUDIO DMA"
default n
endif
endif
endmenu
menu "Board extended module Drivers"
endmenu
endmenu
|
