path: root/bsp/renesas/ra6w1-ek/board/Kconfig

menu "Hardware Drivers Config"

    menu "On-chip Peripheral Drivers"

        config BSP_USING_GPIO_W
            bool "Enable GPIO"
            select RT_USING_PIN
            default y

        menuconfig BSP_USING_UART
            bool "Enable UART"
            default y
            select BSP_USING_GPIO_W
            select RT_USING_SERIAL
            if BSP_USING_UART
                menuconfig BSP_USING_UART0
                    bool "Enable UART0"
                    default y
                    if BSP_USING_UART0
                        config BSP_UART0_RX_PIN
                            string "UART0 RX pin"
                            default "p000"

                        config BSP_UART0_TX_PIN
                            string "UART0 TX pin"
                            default "p001"

                        config BSP_UART0_RX_USING_DMA
                            bool "Enable UART0 RX DMA"
                            depends on BSP_USING_UART0 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART0_TX_USING_DMA
                            bool "Enable UART0 TX DMA"
                            depends on BSP_USING_UART0 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART0_RX_BUFSIZE
                            int "Set UART0 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART0_TX_BUFSIZE
                            int "Set UART0 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART1
                    bool "Enable UART1"
                    default n
                    if BSP_USING_UART1
                        config BSP_UART1_RX_PIN
                            string "UART1 RX pin"
                            default "p004"

                        config BSP_UART1_TX_PIN
                            string "UART1 TX pin"
                            default "p005"

                        config BSP_UART1_RX_USING_DMA
                            bool "Enable UART1 RX DMA"
                            depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART1_TX_USING_DMA
                            bool "Enable UART1 TX DMA"
                            depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART1_RX_BUFSIZE
                            int "Set UART1 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART1_TX_BUFSIZE
                            int "Set UART1 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART2
                    bool "Enable UART2"
                    default n
                    if BSP_USING_UART2
                        config BSP_UART2_RX_PIN
                            string "UART2 RX pin"
                            default "p110"

                        config BSP_UART2_TX_PIN
                            string "UART2 TX pin"
                            default "p111"

                        config BSP_UART2_RX_USING_DMA
                            bool "Enable UART2 RX DMA"
                            depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART2_TX_USING_DMA
                            bool "Enable UART2 TX DMA"
                            depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART2_RX_BUFSIZE
                            int "Set UART2 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART2_TX_BUFSIZE
                            int "Set UART2 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif
            endif

        menuconfig BSP_USING_SPI
            bool "Enable SPI BUS"
            default n
            select BSP_USING_GPIO_W
            select RT_USING_SPI
            if BSP_USING_SPI
                config BSP_USING_SPI0
                    bool "Enable SPI0 BUS"
                    default n
                    if BSP_USING_SPI0
                        config BSP_SPI0_DI_PIN
                            string "SPI0 DI pin"
                            default "p101"

                        config BSP_SPI0_DO_PIN
                            string "SPI0 DO pin"
                            default "p102"

                        config BSP_SPI0_CLK_PIN
                            string "SPI0 CLK pin"
                            default "p100"

                        config BSP_SPI0_CSN0_PIN
                            string "SPI0 CSN0 pin"
                            default "p103"
                    endif

                config BSP_USING_SPI1
                    bool "Enable SPI1 BUS"
                    default n
                    if BSP_USING_SPI1
                        config BSP_SPI1_DI_PIN
                            string "SPI1 DI pin"
                            default "p113"

                        config BSP_SPI1_DO_PIN
                            string "SPI1 DO pin"
                            default "p114"

                        config BSP_SPI1_CLK_PIN
                            string "SPI1 CLK pin"
                            default "p112"

                        config BSP_SPI1_CSN0_PIN
                            string "SPI1 CSN0 pin"
                            default "p115"
                    endif
            endif


        menuconfig BSP_USING_HW_I2C
            bool "Enable hardware I2C bus"
            default n
            select BSP_USING_GPIO_W
            select RT_USING_I2C
            if BSP_USING_HW_I2C
                config BSP_USING_HW_I2C0
                    bool "Enable I2C0 bus"
                    default n
                    if BSP_USING_HW_I2C0
                        choice BSP_USING_HW_I2C0_SPEED
                            prompt "I2C0 Baud Rate Settings"
                            default BSP_I2C0_RATE_FAST
                            config BSP_I2C0_RATE_STANDARD
                                bool "I2C_MASTER_RATE_STANDARD (100 kHz)"
                            config BSP_I2C0_RATE_FAST
                                bool "I2C_MASTER_RATE_FAST (400 kHz)"
                            config BSP_I2C0_RATE_FASTPLUS
                                bool "I2C_MASTER_RATE_FASTPLUS (1 MHz)"
                            config BSP_I2C0_RATE_HIGHSPEED
                                bool "I2C_MASTER_RATE_HIGHSPEED (3.4 MHz)"
                        endchoice

                        config BSP_I2C0_SCL_PIN
                            string "I2C0 SCL pin"
                            default "p004"

                        config BSP_I2C0_SDA_PIN
                            string "I2C0 SDA pin"
                            default "p005"
                    endif

                config BSP_USING_HW_I2C1
                    bool "Enable I2C1 bus"
                    default n
                    if BSP_USING_HW_I2C1

                        choice BSP_USING_HW_I2C1_SPEED
                            prompt "I2C1 Baud Rate Settings"
                            default BSP_I2C1_RATE_FAST
                            config BSP_I2C1_RATE_STANDARD
                                bool "I2C_MASTER_RATE_STANDARD (100 kHz)"
                            config BSP_I2C1_RATE_FAST
                                bool "I2C_MASTER_RATE_FAST (400 kHz)"
                            config BSP_I2C1_RATE_FASTPLUS
                                bool "I2C_MASTER_RATE_FASTPLUS (1 MHz)"
                            config BSP_I2C1_RATE_HIGHSPEED
                                bool "I2C_MASTER_RATE_HIGHSPEED (3.4 MHz)"
                        endchoice

                        config BSP_I2C1_SCL_PIN
                            string "I2C1 SCL pin"
                            default "p006"

                        config BSP_I2C1_SDA_PIN
                            string "I2C1 SDA pin"
                            default "p007"
                    endif
            endif

        menuconfig BSP_USING_ADC
            bool "Enable ADC"
            select BSP_USING_GPIO_W
            select RT_USING_ADC
            default n
            if BSP_USING_ADC
                config BSP_USING_ADC_PIN_NUM
                    int "ADC channel count"
                    range 1 4
                    default 4
            endif

        menuconfig BSP_USING_TIM_W
            bool "Enable timer driver"
            select RT_USING_CLOCK_TIME
            default n
            if BSP_USING_TIM_W
                config BSP_USING_TIM0
                    bool "Enable timer0"
                    default n

                config BSP_USING_TIM1
                    bool "Enable timer1"
                    default n

                config BSP_USING_TIM2
                    bool "Enable timer2"
                    default n

                config BSP_USING_TIM3
                    bool "Enable timer3"
                    default n

                config BSP_USING_TIM4
                    bool "Enable timer4"
                    default n

                config BSP_USING_TIM5
                    bool "Enable timer5"
                    default n

                config BSP_USING_TIM6
                    bool "Enable timer6"
                    default n

                config BSP_USING_TIM7
                    bool "Enable timer7"
                    default n
            endif

        menuconfig BSP_USING_PWM_W
            bool "Enable PWM driver"
            select BSP_USING_GPIO_W
            select RT_USING_PWM
            select BSP_USING_TIM_W
            default n
            if BSP_USING_PWM_W
                config BSP_USING_PWM0
                    bool "Enable PWM0"
                    select BSP_USING_TIM0
                    default n
                    if BSP_USING_PWM0
                        config BSP_PWM0_PIN
                            string "PWM0 pin"
                            default "p004"
                    endif

                config BSP_USING_PWM1
                    bool "Enable PWM1"
                    select BSP_USING_TIM1
                    default n
                    if BSP_USING_PWM1
                        config BSP_PWM1_PIN
                            string "PWM1 pin"
                            default "p005"
                    endif

                config BSP_USING_PWM2
                    bool "Enable PWM2"
                    select BSP_USING_TIM2
                    default n
                    if BSP_USING_PWM2
                        config BSP_PWM2_PIN
                            string "PWM2 pin"
                            default "p006"
                    endif

                config BSP_USING_PWM3
                    bool "Enable PWM3"
                    select BSP_USING_TIM3
                    default n
                    if BSP_USING_PWM3
                        config BSP_PWM3_PIN
                            string "PWM3 pin"
                            default "p007"
                    endif

                config BSP_USING_PWM4
                    bool "Enable PWM4"
                    select BSP_USING_TIM4
                    default n
                    if BSP_USING_PWM4
                        config BSP_PWM4_PIN
                            string "PWM4 pin"
                            default "p100"
                    endif

                config BSP_USING_PWM5
                    bool "Enable PWM5"
                    select BSP_USING_TIM5
                    default n
                    if BSP_USING_PWM5
                        config BSP_PWM5_PIN
                            string "PWM5 pin"
                            default "p101"
                    endif

                config BSP_USING_PWM6
                    bool "Enable PWM6"
                    select BSP_USING_TIM6
                    default n
                    if BSP_USING_PWM6
                        config BSP_PWM6_PIN
                            string "PWM6 pin"
                            default "p102"
                    endif

                config BSP_USING_PWM7
                    bool "Enable PWM7"
                    select BSP_USING_TIM7
                    default n
                    if BSP_USING_PWM7
                        config BSP_PWM7_PIN
                            string "PWM7 pin"
                            default "p103"
                    endif
            endif

        config BSP_USING_QSPI
            bool "Enable QSPI driver"
            select BSP_USING_GPIO_W
            default n

        config BSP_USING_ONCHIP_RTC
            bool "Enable On-chip RTC"
            select RT_USING_RTC
            default n

        config BSP_USING_WDT
            bool "Enable Watchdog Timer"
            select RT_USING_WDT
            default n

    endmenu

    menu "On-chip Peripheral Port"

        config BSP_USING_OSPI_FLASH
            bool "Enable OSPI external flash"
            select RT_USING_FAL
            select FAL_PART_HAS_TABLE_CFG
            default n

        config BSP_USING_QSPI_PSRAM
            bool "Enable QSPI PSRAM"
            select BSP_USING_QSPI
            select RT_USING_MEMHEAP
            default n

    endmenu 
endmenu