path: root/bsp/rockchip/common/rk_hal/lib/hal/src/pinctrl/hal_pinctrl.c

/* SPDX-License-Identifier: BSD-3-Clause */
/*
 * Copyright (c) 2020-2021 Rockchip Electronics Co., Ltd.
 */

#include "hal_base.h"

#if defined(HAL_PINCTRL_MODULE_ENABLED) && (defined(RKMCU_PISCES) || defined(RKMCU_KOALA) || defined(SOC_RK1808) || defined(RKMCU_RK2108) || defined(RKMCU_RK2206))

/** @addtogroup RK_HAL_Driver
 *  @{
 */

/** @addtogroup PINCTRL
 *  @{
 */

/** @defgroup PINCTRL_How_To_Use How To Use
 *  @{

 The pinctrl setting registers actually is bus grf registers, which include
 iomux, drive strength, pull mode, slew rate and schmitt trigger.

 The pinctrl driver provides APIs:
   - HAL_PINCTRL_SetPinIOMUX to set pin iomux
   - HAL_PINCTRL_SetPinParam to set pin drive/pull/slewrate/schmitt

 Example:

     HAL_PINCTRL_SetIOMUX(GPIO_BANK0,
                          GPIO_PIN_A0 | // I2S_IN_SCLK
                          GPIO_PIN_A1 | // I2S_IN_LRCK
                          GPIO_PIN_A2 | // I2S_IN_SDI0
                          GPIO_PIN_A3,  // I2S_IN_SDI1
                          PIN_CONFIG_MUX_FUNC2);

     HAL_PINCTRL_SetParam(GPIO_BANK0,
                          GPIO_PIN_A0 | // I2S_IN_SCLK
                          GPIO_PIN_A1 | // I2S_IN_LRCK
                          GPIO_PIN_A2 | // I2S_IN_SDI0
                          GPIO_PIN_A3,  // I2S_IN_SDI1
                          PIN_CONFIG_PUL_DOWN |
                          PIN_CONFIG_DRV_LEVEL2 |
                          PIN_CONFIG_SRT_FAST |
                          PIN_CONFIG_SMT_ENABLE);
 @} */

/** @defgroup PINCTRL_Private_Definition Private Definition
 *  @{
 */
/********************* Private MACRO Definition ******************************/
#define PIN_READ(r)           (*(volatile uint32_t *)(r))
#define PIN_WRITE(r, b, w, v) (*(volatile uint32_t *)(r) = (((w) << (16) | (v)) << (b)))

/********************* Private Variable Definition ***************************/
__WEAK const struct HAL_PINCTRL_DEV g_pinDev;

/********************* Private Function Definition ***************************/

static const struct HAL_PINCTRL_DEV *PINCTRL_GetInfo(void)
{
    return &g_pinDev;
}

/**
 * @brief  Acquire params for iomux setting.
 * @param  pBank: point to pin bank info.
 * @param  pin: pin index, 0~31.
 * @param  mux: func data.
 * @return HAL_Status.
 */
static HAL_Status PINCTRL_AcquireMuxRoute(const struct PINCTRL_BANK_INFO *pBank, uint8_t pin, uint32_t mux)
{
    const struct HAL_PINCTRL_DEV *ctrl = PINCTRL_GetInfo();
    const struct PINCTRL_MUX_ROUTE_DATA *data;
    uint32_t i, reg = 0;
    HAL_Status rc = HAL_OK;

    if (ctrl->muxRouteDataNum == 0) {
        rc = HAL_ERROR;
        goto exit;
    }

    for (i = 0; i < ctrl->muxRouteDataNum; i++) {
        data = &ctrl->muxRouteData[i];
        if (data->bank == pBank->channel &&
            data->pin & (1 << pin) && data->func == mux) {
            break;
        }
    }

    if (i >= ctrl->muxRouteDataNum) {
        rc = HAL_ERROR;
        goto exit;
    }

    reg = pBank->grfBase + data->routeReg;
    *(volatile uint32_t *)(reg) = data->routeVal;

    HAL_DBG("setting route %08lx = %08lx, %08lx\n", reg, data->routeVal, *(volatile uint32_t *)(reg));
exit:

    return rc;
}

/**
 * @brief  Rectify params for iomux setting.
 * @param  pBank: point to pin bank info.
 * @param  pin: pin index, 0~31.
 * @param  reg: to get reg offset of the pin.
 * @param  bit: to get bit offset of the pin.
 * @param  mask: to get mask bits of the pin.
 * @return HAL_Status.
 */
static HAL_Status PINCTRL_RectifyMuxParams(const struct PINCTRL_BANK_INFO *pBank, uint8_t pin,
                                           uint32_t *reg, uint8_t *bit, uint32_t *mask)
{
    const struct HAL_PINCTRL_DEV *ctrl = PINCTRL_GetInfo();
    const struct PINCTRL_MUX_RECAL_DATA *data;
    uint32_t i;
    HAL_Status rc = HAL_OK;

    if (ctrl->muxRecalDataNum == 0) {
        rc = HAL_ERROR;
        goto exit;
    }

    for (i = 0; i < ctrl->muxRecalDataNum; i++) {
        data = &ctrl->muxRecalData[i];
        if (data->bank == pBank->channel &&
            data->pin == pin) {
            break;
        }
    }

    if (i >= ctrl->muxRecalDataNum) {
        rc = HAL_ERROR;
        goto exit;
    }

    *reg = data->reg;
    *mask = data->mask;
    *bit = data->bit;
exit:

    return rc;
}

/**
 * @brief  Core function to get params.
 * @param  pBank: point to pin bank info.
 * @param  pin: pin index, 0~31.
 * @param  id: get params for @ref ePIN_GRF_INFO_ID.
 * @param  reg: to get reg offset of the pin.
 * @param  bit: to get bit offset of the pin.
 * @param  mask: to get mask bits of the pin.
 * @return HAL_Status: HAL_OK for success to get param.
 */
static HAL_Status PINCTRL_AcquireParam(const struct PINCTRL_BANK_INFO *pBank, uint8_t pin,
                                       ePIN_GRF_INFO_ID id,
                                       uint32_t *reg, uint8_t *bit, uint32_t *mask)
{
    uint8_t paramBit = pBank->GRFInfo[id].bitsPerPin;
    uint8_t paramPin = pBank->GRFInfo[id].pinsPerReg;
    uint32_t regVal, mskVal;
    uint8_t bitVal;

    /* The '0' value means nothing to set */
    if (paramBit <= 0) {
        return HAL_ERROR;
    }

    /* GRF(PMUGRF) address + mux offset + pin offset */
    regVal = pBank->grfBase;
    regVal += pBank->GRFInfo[id].offset;
    regVal += (pin / paramPin) * 4;

    bitVal = (pin % paramPin) * paramBit;
    mskVal = (0x1U << paramBit) - 0x1U;

    *reg = regVal;
    *bit = bitVal;
    *mask = mskVal;

    return HAL_OK;
}

#if defined(RKMCU_RK2206)
#define GRF_SARADC_IEN_EN(x)   ((0x0U << GRF_SOC_CON15_GRF_SARADC_IEN_SHIFT) << (x))
#define GRF_SARADC_IEN_DIS(x)  ((0x1U << GRF_SOC_CON15_GRF_SARADC_IEN_SHIFT) << (x))
#define GRF_SARADC_IEN_MASK(x) ((0x1U << GRF_SOC_CON15_GRF_SARADC_IEN_SHIFT) << (x))
#define IS_MUX_SARADC(m)       ((m) == PIN_CONFIG_MUX_FUNC1)

/**
 * @brief  Extra iomux for GPIO0_C0-GPIO0_C7 on rk2206 SoCs.
 * @param  pBank: point to pin bank info.
 * @param  pin: pin index, 0~31.
 * @param  arg: multi params defined in @ref ePINCTRL_configParam,
 */
static void PINCTRL_ExtraSet(const struct PINCTRL_BANK_INFO *pBank, uint8_t pin, uint32_t arg)
{
    if (pin < 16 || pin > 23 || (pBank->channel != GPIO_BANK0)) {
        return;
    }

    if (IS_MUX_SARADC(arg)) {
        WRITE_REG_MASK_WE(GRF->SOC_CON15,
                          GRF_SARADC_IEN_MASK(pin - 16),
                          GRF_SARADC_IEN_DIS(pin - 16));
    } else {
        WRITE_REG_MASK_WE(GRF->SOC_CON15,
                          GRF_SARADC_IEN_MASK(pin - 16),
                          GRF_SARADC_IEN_EN(pin - 16));
    }
}
#else
static inline void PINCTRL_ExtraSet(const struct PINCTRL_BANK_INFO *pBank, uint8_t pin, uint32_t arg)
{
}
#endif

/**
 * @brief  Private function to set iomux for one pin.
 * @param  pBank: point to pin bank info.
 * @param  pin: pin index, 0~31.
 * @param  param: mux value  to set.
 * @return HAL_Status.
 */
static HAL_Status PINCTRL_SetMux(const struct PINCTRL_BANK_INFO *pBank,
                                 uint8_t pin, uint8_t param)
{
    uint32_t reg = 0, mask = 0;
    uint8_t bit = 0;
    HAL_Status rc = HAL_OK;

    HAL_DBG("setting GPIO%d-%d to %d\n", pBank->channel, pin, param);

    rc = PINCTRL_AcquireParam(pBank, pin, GRF_MUX_INFO, &reg, &bit, &mask);
    if (rc) {
        HAL_DBG("Warning: Acquire Mux Param failed\n");
    }

    rc = PINCTRL_RectifyMuxParams(pBank, pin, &reg, &bit, &mask);
    if (rc == HAL_OK) {
        HAL_DBG("Warning: Param is rectified\n");
    }

    PIN_WRITE(reg, bit, mask, param);

    rc = PINCTRL_AcquireMuxRoute(pBank, pin, param);
    if (rc == HAL_OK) {
        HAL_DBG("setting route for GPIO%d-%d\n", pBank->channel, pin);
    }

    return HAL_OK;
}

/**
 * @brief  Set a new drive strength for a pin.
 * @param  pBank: point to pin bank info.
 * @param  pin: pin index, 0~31.
 * @param  param: drive strength to set.
 * @return HAL_Status.
 */
static uint32_t PINCTRL_SetDrive(const struct PINCTRL_BANK_INFO *pBank,
                                 uint8_t pin, uint8_t param)
{
    uint32_t reg = 0, mask = 0;
    uint8_t bit = 0;
    HAL_Status rc = HAL_OK;

    HAL_DBG("setting GPIO%d-%d drive to %d\n", pBank->channel, pin, param);

    rc = PINCTRL_AcquireParam(pBank, pin, GRF_DRV_INFO, &reg, &bit, &mask);
    if (rc) {
        goto exit;
    }

    PIN_WRITE(reg, bit, mask, param);
exit:

    return rc;
}

/**
 * @brief  Set a new pull mode for a pin.
 * @param  pBank: point to pin bank info.
 * @param  pin: pin index, 0~31.
 * @param  param: pull mode to set.
 * @return HAL_Status.
 */
static HAL_Status PINCTRL_SetPull(const struct PINCTRL_BANK_INFO *pBank,
                                  uint8_t pin, uint8_t param)
{
    uint32_t reg = 0, mask = 0;
    uint8_t bit = 0;
    HAL_Status rc = HAL_OK;

    HAL_DBG("setting GPIO%d-%d pull to %d\n", pBank->channel, pin, param);

    rc = PINCTRL_AcquireParam(pBank, pin, GRF_PUL_INFO, &reg, &bit, &mask);
    if (rc) {
        goto exit;
    }

    PIN_WRITE(reg, bit, mask, param);
exit:

    return rc;
}

/**
 * @brief  Enable schmitt trigger for a pin.
 * @param  pBank: point to pin bank info.
 * @param  pin: pin index, 0~31.
 * @param  param: schmitt trigger enable or not.
 * @return HAL_Status.
 */
static HAL_Status PINCTRL_SetSchmitt(const struct PINCTRL_BANK_INFO *pBank,
                                     uint8_t pin, uint8_t param)
{
    uint32_t reg = 0, mask = 0;
    uint8_t bit = 0;
    HAL_Status rc = HAL_OK;

    HAL_DBG("setting GPIO%d-%d schmitt to %d\n", pBank->channel, pin, param);

    rc = PINCTRL_AcquireParam(pBank, pin, GRF_SMT_INFO, &reg, &bit, &mask);
    if (rc) {
        goto exit;
    }

    PIN_WRITE(reg, bit, mask, param);
exit:

    return rc;
}

/**
 * @brief  Change slew rate for a pin.
 * @param  pBank: point to pin bank info.
 * @param  pin: pin index, 0~31.
 * @param  param: slew rate fast or slow
 * @return HAL_Status.
 */
static HAL_Status PINCTRL_SetSlewRate(const struct PINCTRL_BANK_INFO *pBank,
                                      uint8_t pin, uint8_t param)
{
    uint32_t reg = 0, mask = 0;
    uint8_t bit = 0;
    HAL_Status rc = HAL_OK;

    HAL_DBG("setting GPIO%d-%d slewrate to %d\n", pBank->channel, pin, param);

    rc = PINCTRL_AcquireParam(pBank, pin, GRF_SRT_INFO, &reg, &bit, &mask);
    if (rc) {
        goto exit;
    }

    PIN_WRITE(reg, bit, mask, param);
exit:

    return rc;
}

/**
 * @brief  Private function to configure one pin.
 * @param  bank: pin bank channel defined in @ref eGPIO_bankId.
 * @param  pin: pin index, 0~31.
 * @param  param: multi params defined in @ref ePINCTRL_configParam,
 * @return HAL_Status.
 */
static HAL_Status PINCTRL_SetParam(const struct PINCTRL_BANK_INFO *pBank,
                                   uint8_t pin, uint32_t param)
{
    HAL_Status rc = HAL_OK;

    if (param & FLAG_PUL) {
        rc |= PINCTRL_SetPull(pBank, pin, (uint8_t)((param & MASK_PUL) >> SHIFT_PUL));
    }

    if (param & FLAG_DRV) {
        rc |= PINCTRL_SetDrive(pBank, pin, (uint8_t)((param & MASK_DRV) >> SHIFT_DRV));
    }

    if (param & FLAG_SMT) {
        rc |= PINCTRL_SetSchmitt(pBank, pin, (uint8_t)((param & MASK_SMT) >> SHIFT_SMT));
    }

    if (param & FLAG_SRT) {
        rc |= PINCTRL_SetSlewRate(pBank, pin, (uint8_t)((param & MASK_SRT) >> SHIFT_SRT));
    }

    return rc;
}

/**
 * @brief  Private function to configure one pin.
 * @param  bank: pin bank channel defined in @ref eGPIO_bankId.
 * @param  pin: pin index, 0~31.
 * @param  param: multi params defined in @ref ePINCTRL_configParam,
 * @return HAL_Status.
 */
static HAL_Status PINCTRL_SetPinParam(eGPIO_bankId bank, uint8_t pin, uint32_t param)
{
    const struct HAL_PINCTRL_DEV *ctrl = PINCTRL_GetInfo();

    return PINCTRL_SetParam(&ctrl->banks[bank], pin, param);
}

/**
 * @brief  Private function to set iomux for one pin.
 * @param  bank: pin bank channel defined in @ref eGPIO_bankId.
 * @param  pin: pin index, 0~31.
 * @param  param: PIN_CONFIG_MUX_* defined in @ref ePINCTRL_configParam.
 * @return HAL_Status.
 */
static HAL_Status PINCTRL_SetPinIOMUX(eGPIO_bankId bank, uint8_t pin, uint32_t param)
{
    const struct HAL_PINCTRL_DEV *ctrl = PINCTRL_GetInfo();

    PINCTRL_ExtraSet(&ctrl->banks[bank], pin, param);

    return PINCTRL_SetMux(&ctrl->banks[bank], pin, (uint8_t)((param & MASK_MUX) >> SHIFT_MUX));
}

/** @} */
/********************* Public Function Definition ****************************/

/** @defgroup PINCTRL_Exported_Functions_Group1 Suspend and Resume Functions

 This section provides functions allowing to suspend and resume the module:

 *  @{
 */

HAL_Status HAL_PINCTRL_Suspend(void)
{
    return HAL_OK;
}

HAL_Status HAL_PINCTRL_Resume(void)
{
    return HAL_OK;
}
/** @} */

/** @defgroup PINCTRL_Exported_Functions_Group2 Init and DeInit Functions

 This section provides functions allowing to init and deinit the module:

 *  @{
 */

HAL_Status HAL_PINCTRL_Init(void)
{
#ifdef RKMCU_PISCES
    HAL_PINCTRL_SetIOMUX(GPIO_BANK0, GPIO_PIN_ALL & ~(
                             GPIO_PIN_C7 | // UART0_RX
                             GPIO_PIN_D0 | // UART0_TX
                             GPIO_PIN_D5 | // MIPI_SWITCH_CTRL
                             GPIO_PIN_D6), // AUD_BY_CTRL
                         PIN_CONFIG_MUX_FUNC0);
    HAL_PINCTRL_SetIOMUX(GPIO_BANK1, GPIO_PIN_ALL & ~(
                             GPIO_PIN_A0 | // LCD_IN_RESET_N
                             GPIO_PIN_A1 | // LCD_IN_TE
                             GPIO_PIN_A2 | // LCD_OUT_RESETN
                             GPIO_PIN_A3 | // LCD_OUT_TE
                             GPIO_PIN_A5 | // BOOT_DEV_SEL
                             GPIO_PIN_A6 | // M4_DSP_JTAG_SEL
                             GPIO_PIN_B2), // CLK_IN_SEL
                         PIN_CONFIG_MUX_FUNC0);

    HAL_PINCTRL_SetParam(GPIO_BANK0, GPIO_PIN_ALL & ~(
                             GPIO_PIN_D5 | // MIPI_SWITCH_CTRL
                             GPIO_PIN_D6), // AUD_BY_CTRL
                         PIN_CONFIG_PUL_NORMAL);
    HAL_PINCTRL_SetParam(GPIO_BANK1, GPIO_PIN_ALL & ~(
                             GPIO_PIN_A5 | // BOOT_DEV_SEL
                             GPIO_PIN_A6 | // M4_DSP_JTAG_SEL
                             GPIO_PIN_B2), // CLK_IN_SEL
                         PIN_CONFIG_PUL_NORMAL);
#endif

    return HAL_OK;
}

HAL_Status HAL_PINCTRL_DeInit(void)
{
    return HAL_OK;
}
/** @} */

/** @defgroup PINCTRL_Exported_Functions_Group3 State and Errors Functions

 This section provides functions allowing to get the status of the module:

 *  @{
 */

/**
 * @brief  Public function to configure for multi pins.
 * @param  bank: pin bank channel defined in ref eGPIO_bankId.
 * @param  mPins: multi pins defined in @ref ePINCTRL_GPIO_PINS.
 * @param  param: multi params defined in @ref ePINCTRL_configParam,
 * @return HAL_Status.
 */
HAL_Status HAL_PINCTRL_SetParam(eGPIO_bankId bank, uint32_t mPins, ePINCTRL_configParam param)
{
    uint8_t pin;
    HAL_Status rc = HAL_OK;

    HAL_ASSERT(bank < GPIO_BANK_NUM);
    HAL_ASSERT(IS_GPIO_PIN(mPins));

    for (pin = 0; pin < 32; pin++) {
        if (mPins & (1 << pin)) {
            rc = PINCTRL_SetPinParam(bank, pin, param);
            if (rc) {
                return rc;
            }
        }
    }

    return rc;
}

/**
 * @brief  Public function to set iomux for multi pins.
 * @param  bank: pin bank channel defined in ref eGPIO_bankId.
 * @param  mPins: multi pins defined in @ref ePINCTRL_GPIO_PINS.
 * @param  param: param PIN_CONFIG_MUX_* defined in @ref ePINCTRL_configParam.
 * @return HAL_Status.
 */
HAL_Status HAL_PINCTRL_SetIOMUX(eGPIO_bankId bank, uint32_t mPins, ePINCTRL_configParam param)
{
    uint8_t pin;
    HAL_Status rc;

    HAL_ASSERT(bank < GPIO_BANK_NUM);

    for (pin = 0; pin < 32; pin++) {
        if (mPins & (1 << pin)) {
            rc = PINCTRL_SetPinIOMUX(bank, pin, param);
            if (rc) {
                return rc;
            }
        }
    }

    return HAL_OK;
}
/** @} */

/** @defgroup PINCTRL_Exported_Functions_Group4 IO Functions

 This section provides functions allowing to IO controlling:

 *  @{
 */

/** @} */

/** @} */

/** @} */

#endif /* HAL_PINCTRL_MODULE_ENABLED */