1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
|
/**
* \file
*
* \brief SAM Brown Out Detector Driver
*
* Copyright (C) 2015 Atmel Corporation. All rights reserved.
*
* \asf_license_start
*
* \page License
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* 3. The name of Atmel may not be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* 4. This software may only be redistributed and used in connection with an
* Atmel microcontroller product.
*
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
* \asf_license_stop
*
*/
/*
* Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
*/
#include "bod.h"
/**
* \brief Configure a Brown Out Detector module.
*
* Configures a given BOD module with the settings stored in the given
* configuration structure.
*
* \param[in] conf Configuration settings to use for the specified BODVDD
*
* \retval STATUS_OK Operation completed successfully
* \retval STATUS_ERR_INVALID_ARG An invalid BOD was supplied
* \retval STATUS_ERR_INVALID_OPTION The requested BOD level was outside the acceptable range
*/
enum status_code bodvdd_set_config(
struct bodvdd_config *const conf)
{
/* Sanity check arguments */
Assert(conf);
uint32_t temp = 0;
/* Check if module is enabled. */
if (SUPC->BODVDD.reg & SUPC_BODVDD_ENABLE) {
SUPC->BODVDD.reg &= ~SUPC_BODVDD_ENABLE;
}
/* Convert BOD prescaler, trigger action and mode to a bitmask */
temp |= (uint32_t)conf->prescaler | (uint32_t)conf->action |
(uint32_t)conf->mode_in_active | (uint32_t)conf->mode_in_standby;
if (conf->hysteresis == true) {
temp |= SUPC_BODVDD_HYST;
}
if (conf->run_in_standby == true) {
temp |= SUPC_BODVDD_RUNSTDBY;
}
if (conf->level > 0x3F) {
return STATUS_ERR_INVALID_ARG;
}
SUPC->BODVDD.reg = SUPC_BODVDD_LEVEL(conf->level) | temp;
return STATUS_OK;
}
|
