path: root/bsp/samd21/sam_d2x_asflib/sam0/drivers/port/port.h

/**
 * \file
 *
 * \brief SAM GPIO Port Driver
 *
 * Copyright (C) 2012-2016 Atmel Corporation. All rights reserved.
 *
 * \asf_license_start
 *
 * \page License
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 *    this list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 *
 * 3. The name of Atmel may not be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * 4. This software may only be redistributed and used in connection with an
 *    Atmel microcontroller product.
 *
 * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 * \asf_license_stop
 *
 */
/*
 * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
 */
#ifndef PORT_H_INCLUDED
#define PORT_H_INCLUDED

/**
 * \defgroup asfdoc_sam0_port_group SAM Port (PORT) Driver
 *
 * This driver for Atmel&reg; | SMART ARM&reg;-based microcontrollers provides
 * an interface for the configuration and management of the device's General
 * Purpose Input/Output (GPIO) pin functionality, for manual pin state reading
 * and writing.
 *
 * The following peripheral is used by this module:
 *  - PORT (GPIO Management)
 *
 * The following devices can use this module:
 *  - Atmel | SMART SAM D20/D21
 *  - Atmel | SMART SAM R21
 *  - Atmel | SMART SAM D09/D10/D11
 *  - Atmel | SMART SAM L21/L22
 *  - Atmel | SMART SAM DA1
 *  - Atmel | SMART SAM C20/C21
 *  - Atmel | SMART SAM HA1
 *  - Atmel | SMART SAM R30
 *
 * The outline of this documentation is as follows:
 *  - \ref asfdoc_sam0_port_prerequisites
 *  - \ref asfdoc_sam0_port_module_overview
 *  - \ref asfdoc_sam0_port_special_considerations
 *  - \ref asfdoc_sam0_port_extra_info
 *  - \ref asfdoc_sam0_port_examples
 *  - \ref asfdoc_sam0_port_api_overview
 *
 *
 * \section asfdoc_sam0_port_prerequisites Prerequisites
 *
 * There are no prerequisites for this module.
 *
 *
 * \section asfdoc_sam0_port_module_overview Module Overview
 *
 * The device GPIO (PORT) module provides an interface between the user
 * application logic and external hardware peripherals, when general pin state
 * manipulation is required. This driver provides an easy-to-use interface to
 * the physical pin input samplers and output drivers, so that pins can be read
 * from or written to for general purpose external hardware control.
 *
 * \subsection asfdoc_sam0_port_features Driver Feature Macro Definition
 * <table>
 *  <tr>
 *    <th>Driver Feature Macro</th>
 *    <th>Supported devices</th>
 *  </tr>
 *  <tr>
 *    <td>FEATURE_PORT_INPUT_EVENT</td>
 *    <td>SAM L21/L22/C20/C21/R30</td>
 *  </tr>
 * </table>
 * \note The specific features are only available in the driver when the
 * selected device supports those features.
 *
 * \subsection asfdoc_sam0_port_module_overview_pin_numbering Physical and Logical GPIO Pins
 * SAM devices use two naming conventions for the I/O pins in the device; one
 * physical and one logical. Each physical pin on a device package is assigned
 * both a physical port and pin identifier (e.g. "PORTA.0") as well as a
 * monotonically incrementing logical GPIO number (e.g. "GPIO0"). While the
 * former is used to map physical pins to their physical internal device module
 * counterparts, for simplicity the design of this driver uses the logical GPIO
 * numbers instead.
 *
 * \subsection asfdoc_sam0_port_module_overview_physical Physical Connection
 *
 * \ref asfdoc_sam0_port_module_int_connections "The diagram below" shows how
 * this module is interconnected within the device.
 *
 * \anchor asfdoc_sam0_port_module_int_connections
 * \dot
 * digraph overview {
 *   node [label="Port Pad" shape=square] pad;
 *
 *   subgraph driver {
 *     node [label="Peripheral MUX" shape=trapezium] pinmux;
 *     node [label="GPIO Module" shape=ellipse] gpio;
 *     node [label="Other Peripheral Modules" shape=ellipse style=filled fillcolor=lightgray] peripherals;
 *   }
 *
 *   pinmux -> gpio;
 *   pad    -> pinmux;
 *   pinmux -> peripherals;
 * }
 * \enddot
 *
 *
 * \section asfdoc_sam0_port_special_considerations Special Considerations
 *
 * The SAM port pin input sampler can be disabled when the pin is configured
 * in pure output mode to save power; reading the pin state of a pin configured
 * in output-only mode will read the logical output state that was last set.
 *
 * \section asfdoc_sam0_port_extra_info Extra Information
 *
 * For extra information, see \ref asfdoc_sam0_port_extra. This includes:
 *  - \ref asfdoc_sam0_port_extra_acronyms
 *  - \ref asfdoc_sam0_port_extra_dependencies
 *  - \ref asfdoc_sam0_port_extra_errata
 *  - \ref asfdoc_sam0_port_extra_history
 *
 *
 * \section asfdoc_sam0_port_examples Examples
 *
 * For a list of examples related to this driver, see
 * \ref asfdoc_sam0_port_exqsg.
 *
 *
 * \section asfdoc_sam0_port_api_overview API Overview
 * @{
 */

#include <compiler.h>
#include <pinmux.h>

#ifdef __cplusplus
extern "C" {
#endif

/**
 * \name Driver Feature Definition
 * Define port features set according to different device family.
 * @{
*/
#if (SAML21) || (SAML22) || (SAMC20) || (SAMC21) || (SAMR30) || defined(__DOXYGEN__)
/** Event input control feature support for PORT group. */
#  define FEATURE_PORT_INPUT_EVENT
#endif
/*@}*/

/** \name PORT Alias Macros
 * @{
 */

/** Convenience definition for GPIO module group A on the device (if
 *  available). */
#if (PORT_GROUPS > 0) || defined(__DOXYGEN__)
#  define PORTA             PORT->Group[0]
#endif

#if (PORT_GROUPS > 1) || defined(__DOXYGEN__)
/** Convenience definition for GPIO module group B on the device (if
 *  available). */
#  define PORTB             PORT->Group[1]
#endif

#if (PORT_GROUPS > 2) || defined(__DOXYGEN__)
/** Convenience definition for GPIO module group C on the device (if
 *  available). */
#  define PORTC             PORT->Group[2]
#endif

#if (PORT_GROUPS > 3) || defined(__DOXYGEN__)
/** Convenience definition for GPIO module group D on the device (if
 *  available). */
#  define PORTD             PORT->Group[3]
#endif

/** @} */

/**
 *  \brief Port pin direction configuration enum.
 *
 *  Enum for the possible pin direction settings of the port pin configuration
 *  structure, to indicate the direction the pin should use.
 */
enum port_pin_dir {
	/** The pin's input buffer should be enabled, so that the pin state can
	 *  be read */
	PORT_PIN_DIR_INPUT               = SYSTEM_PINMUX_PIN_DIR_INPUT,
	/** The pin's output buffer should be enabled, so that the pin state can
	 *  be set */
	PORT_PIN_DIR_OUTPUT              = SYSTEM_PINMUX_PIN_DIR_OUTPUT,
	/** The pin's output and input buffers should be enabled, so that the pin
	 *  state can be set and read back */
	PORT_PIN_DIR_OUTPUT_WTH_READBACK = SYSTEM_PINMUX_PIN_DIR_OUTPUT_WITH_READBACK,
};

/**
 *  \brief Port pin input pull configuration enum.
 *
 *  Enum for the possible pin pull settings of the port pin configuration
 *  structure, to indicate the type of logic level pull the pin should use.
 */
enum port_pin_pull {
	/** No logical pull should be applied to the pin */
	PORT_PIN_PULL_NONE = SYSTEM_PINMUX_PIN_PULL_NONE,
	/** Pin should be pulled up when idle */
	PORT_PIN_PULL_UP   = SYSTEM_PINMUX_PIN_PULL_UP,
	/** Pin should be pulled down when idle */
	PORT_PIN_PULL_DOWN = SYSTEM_PINMUX_PIN_PULL_DOWN,
};

#ifdef FEATURE_PORT_INPUT_EVENT
/**
 *  \brief Port input event action.
 *
 *  List of port input events action on pin.
 */
enum port_input_event_action {
	/** Event out to pin */
	PORT_INPUT_EVENT_ACTION_OUT = 0,
	/** Set output register of pin on event */
	PORT_INPUT_EVENT_ACTION_SET,
	/** Clear output register pin on event */
	PORT_INPUT_EVENT_ACTION_CLR,
	/** Toggle output register pin on event */
	PORT_INPUT_EVENT_ACTION_TGL,
};

/**
 *  \brief Port input event.
 *
 *  List of port input events.
 */
enum port_input_event{
	/** Port input event 0 */
	PORT_INPUT_EVENT_0 = 0,
	/** Port input event 1 */
	PORT_INPUT_EVENT_1 = 1,
	/** Port input event 2 */
	PORT_INPUT_EVENT_2 = 2,
	/** Port input event 3 */
	PORT_INPUT_EVENT_3 = 3,
};

/**
 *  \brief Port input event configuration structure.
 *
 *  Configuration structure for a port input event.
 */
struct port_input_event_config{
	/** Port input event action */
	enum port_input_event_action  action;
	/** GPIO pin */
	uint8_t gpio_pin;
};
#endif

/**
 *  \brief Port pin configuration structure.
 *
 *  Configuration structure for a port pin instance. This structure should be
 *  initialized by the \ref port_get_config_defaults() function before being
 *  modified by the user application.
 */
struct port_config {
	/** Port buffer input/output direction */
	enum port_pin_dir  direction;

	/** Port pull-up/pull-down for input pins */
	enum port_pin_pull input_pull;

	/** Enable lowest possible powerstate on the pin
	 *
	 *  \note All other configurations will be ignored, the pin will be disabled.
	 */
	bool powersave;
};

/** \name State Reading/Writing (Physical Group Orientated)
 * @{
 */

/**
 *  \brief Retrieves the PORT module group instance from a given GPIO pin number.
 *
 *  Retrieves the PORT module group instance associated with a given logical
 *  GPIO pin number.
 *
 *  \param[in] gpio_pin  Index of the GPIO pin to convert
 *
 *  \return Base address of the associated PORT module.
 */
static inline PortGroup* port_get_group_from_gpio_pin(
		const uint8_t gpio_pin)
{
	return system_pinmux_get_group_from_gpio_pin(gpio_pin);
}

/**
 *  \brief Retrieves the state of a group of port pins that are configured as inputs.
 *
 *  Reads the current logic level of a port module's pins and returns the
 *  current levels as a bitmask.
 *
 *  \param[in] port  Base of the PORT module to read from
 *  \param[in] mask  Mask of the port pin(s) to read
 *
 *  \return Status of the port pin(s) input buffers.
 */
static inline uint32_t port_group_get_input_level(
		const PortGroup *const port,
		const uint32_t mask)
{
	/* Sanity check arguments */
	Assert(port);

	return (port->IN.reg & mask);
}

/**
 *  \brief Retrieves the state of a group of port pins that are configured as outputs.
 *
 *  Reads the current logical output level of a port module's pins and returns
 *  the current levels as a bitmask.
 *
 *  \param[in] port  Base of the PORT module to read from
 *  \param[in] mask  Mask of the port pin(s) to read
 *
 *  \return Status of the port pin(s) output buffers.
 */
static inline uint32_t port_group_get_output_level(
		const PortGroup *const port,
		const uint32_t mask)
{
	/* Sanity check arguments */
	Assert(port);

	return (port->OUT.reg & mask);
}

/**
 *  \brief Sets the state of a group of port pins that are configured as outputs.
 *
 *  Sets the current output level of a port module's pins to a given logic
 *  level.
 *
 *  \param[out] port        Base of the PORT module to write to
 *  \param[in]  mask        Mask of the port pin(s) to change
 *  \param[in]  level_mask  Mask of the port level(s) to set
 */
static inline void port_group_set_output_level(
		PortGroup *const port,
		const uint32_t mask,
		const uint32_t level_mask)
{
	/* Sanity check arguments */
	Assert(port);

	port->OUTSET.reg = (mask &  level_mask);
	port->OUTCLR.reg = (mask & ~level_mask);
}

/**
 *  \brief Toggles the state of a group of port pins that are configured as an outputs.
 *
 *  Toggles the current output levels of a port module's pins.
 *
 *  \param[out] port  Base of the PORT module to write to
 *  \param[in]  mask  Mask of the port pin(s) to toggle
 */
static inline void port_group_toggle_output_level(
		PortGroup *const port,
		const uint32_t mask)
{
	/* Sanity check arguments */
	Assert(port);

	port->OUTTGL.reg = mask;
}

/** @} */

/** \name Configuration and Initialization
 * @{
 */

/**
 *  \brief Initializes a Port pin/group configuration structure to defaults.
 *
 *  Initializes a given Port pin/group configuration structure to a set of
 *  known default values. This function should be called on all new
 *  instances of these configuration structures before being modified by the
 *  user application.
 *
 *  The default configuration is as follows:
 *   \li Input mode with internal pull-up enabled
 *
 *  \param[out] config  Configuration structure to initialize to default values
 */
static inline void port_get_config_defaults(
		struct port_config *const config)
{
	/* Sanity check arguments */
	Assert(config);

	/* Default configuration values */
	config->direction  = PORT_PIN_DIR_INPUT;
	config->input_pull = PORT_PIN_PULL_UP;
	config->powersave  = false;
}

void port_pin_set_config(
		const uint8_t gpio_pin,
		const struct port_config *const config);

void port_group_set_config(
		PortGroup *const port,
		const uint32_t mask,
		const struct port_config *const config);

/** @} */

/** \name State Reading/Writing (Logical Pin Orientated)
 * @{
 */

/**
 *  \brief Retrieves the state of a port pin that is configured as an input.
 *
 *  Reads the current logic level of a port pin and returns the current
 *  level as a Boolean value.
 *
 *  \param[in] gpio_pin  Index of the GPIO pin to read
 *
 *  \return Status of the port pin's input buffer.
 */
static inline bool port_pin_get_input_level(
		const uint8_t gpio_pin)
{
	PortGroup *const port_base = port_get_group_from_gpio_pin(gpio_pin);
	uint32_t pin_mask  = (1UL << (gpio_pin % 32));

	return (port_base->IN.reg & pin_mask);
}

/**
 *  \brief Retrieves the state of a port pin that is configured as an output.
 *
 *  Reads the current logical output level of a port pin and returns the current
 *  level as a Boolean value.
 *
 *  \param[in] gpio_pin  Index of the GPIO pin to read
 *
 *  \return Status of the port pin's output buffer.
 */
static inline bool port_pin_get_output_level(
		const uint8_t gpio_pin)
{
	PortGroup *const port_base = port_get_group_from_gpio_pin(gpio_pin);
	uint32_t pin_mask  = (1UL << (gpio_pin % 32));

	return (port_base->OUT.reg & pin_mask);
}

/**
 *  \brief Sets the state of a port pin that is configured as an output.
 *
 *  Sets the current output level of a port pin to a given logic level.
 *
 *  \param[in] gpio_pin  Index of the GPIO pin to write to
 *  \param[in] level     Logical level to set the given pin to
 */
static inline void port_pin_set_output_level(
		const uint8_t gpio_pin,
		const bool level)
{
	PortGroup *const port_base = port_get_group_from_gpio_pin(gpio_pin);
	uint32_t pin_mask  = (1UL << (gpio_pin % 32));

	/* Set the pin to high or low atomically based on the requested level */
	if (level) {
		port_base->OUTSET.reg = pin_mask;
	} else {
		port_base->OUTCLR.reg = pin_mask;
	}
}

/**
 *  \brief Toggles the state of a port pin that is configured as an output.
 *
 *  Toggles the current output level of a port pin.
 *
 *  \param[in] gpio_pin  Index of the GPIO pin to toggle
 */
static inline void port_pin_toggle_output_level(
		const uint8_t gpio_pin)
{
	PortGroup *const port_base = port_get_group_from_gpio_pin(gpio_pin);
	uint32_t pin_mask  = (1UL << (gpio_pin % 32));

	/* Toggle pin output level */
	port_base->OUTTGL.reg = pin_mask;
}

/** @} */

#ifdef FEATURE_PORT_INPUT_EVENT

/** \name Port Input Event
 * @{
 */

/**
 *  \brief Enable the port event input.
 *
 *  Enable the port event input with the given pin and event.
 *
 *  \param[in] gpio_pin  Index of the GPIO pin
 *  \param[in] n  Port input event
 *
 * \retval STATUS_ERR_INVALID_ARG  Invalid parameter
 * \retval STATUS_OK               Successfully
 */
static inline enum status_code port_enable_input_event(
		const uint8_t gpio_pin,
		const enum port_input_event n)
{
	PortGroup *const port_base = port_get_group_from_gpio_pin(gpio_pin);
	switch (n) {
		case PORT_INPUT_EVENT_0:
			port_base->EVCTRL.reg |= PORT_EVCTRL_PORTEI0;
			break;
		case PORT_INPUT_EVENT_1:
			port_base->EVCTRL.reg |= PORT_EVCTRL_PORTEI1;
			break;
		case PORT_INPUT_EVENT_2:
			port_base->EVCTRL.reg |= PORT_EVCTRL_PORTEI2;
			break;
		case PORT_INPUT_EVENT_3:
			port_base->EVCTRL.reg |= PORT_EVCTRL_PORTEI3;
			break;
		default:
			Assert(false);
			return STATUS_ERR_INVALID_ARG;
	}
	return STATUS_OK;
}

/**
 *  \brief Disable the port event input.
 *
 *  Disable the port event input with the given pin and event.
 *
 *  \param[in] gpio_pin  Index of the GPIO pin
 *  \param[in] gpio_pin  Port input event
 *
 * \retval STATUS_ERR_INVALID_ARG  Invalid parameter
 * \retval STATUS_OK               Successfully
 */
static inline enum status_code port_disable_input_event(
		const uint8_t gpio_pin,
		const enum port_input_event n)
{
	PortGroup *const port_base = port_get_group_from_gpio_pin(gpio_pin);
	switch (n) {
		case PORT_INPUT_EVENT_0:
			port_base->EVCTRL.reg &= ~PORT_EVCTRL_PORTEI0;
			break;
		case PORT_INPUT_EVENT_1:
			port_base->EVCTRL.reg &= ~PORT_EVCTRL_PORTEI1;
			break;
		case PORT_INPUT_EVENT_2:
			port_base->EVCTRL.reg &= ~PORT_EVCTRL_PORTEI2;
			break;
		case PORT_INPUT_EVENT_3:
			port_base->EVCTRL.reg &= ~PORT_EVCTRL_PORTEI3;
			break;
		default:
			Assert(false);
			return STATUS_ERR_INVALID_ARG;
	}
	return STATUS_OK;
}

/**
 * \brief Retrieve the default configuration for port input event.
 *
 * Fills a configuration structure with the default configuration for port input event:
 *   - Event output to pin
 *   - Event action to be executed on PIN 0
 *
 * \param[out] config  Configuration structure to fill with default values
 */
static inline void port_input_event_get_config_defaults(
		struct port_input_event_config *const config)
{
	Assert(config);
	config->action   = PORT_INPUT_EVENT_ACTION_OUT;
	config->gpio_pin = 0;
}

/**
 * \brief Configure port input event.
 *
 * Configures port input event with the given configuration settings.
 *
 * \param[in] config  Port input even configuration structure containing the new config
 *
 * \retval STATUS_ERR_INVALID_ARG  Invalid parameter
 * \retval STATUS_OK               Successfully
 */

static inline enum status_code port_input_event_set_config(
		const enum port_input_event n,
		struct port_input_event_config *const config)
{
	Assert(config);
	PortGroup *const port_base = port_get_group_from_gpio_pin(config->gpio_pin);
	uint8_t pin_index = config->gpio_pin % 32;
	struct port_config pin_conf;

	port_get_config_defaults(&pin_conf);
	/* Configure the GPIO pin as outputs*/
	pin_conf.direction  = PORT_PIN_DIR_OUTPUT;
	port_pin_set_config(config->gpio_pin, &pin_conf);

	switch (n) {
		case PORT_INPUT_EVENT_0:
			port_base->EVCTRL.reg |= PORT_EVCTRL_EVACT0(config->action)
									| PORT_EVCTRL_PID0(pin_index);
			break;
		case PORT_INPUT_EVENT_1:
			port_base->EVCTRL.reg |= PORT_EVCTRL_EVACT1(config->action)
						   		   | PORT_EVCTRL_PID1(pin_index);
			break;
		case PORT_INPUT_EVENT_2:
			port_base->EVCTRL.reg |= PORT_EVCTRL_EVACT2(config->action)
						   		   | PORT_EVCTRL_PID2(pin_index);
			break;
		case PORT_INPUT_EVENT_3:
			port_base->EVCTRL.reg |= PORT_EVCTRL_EVACT3(config->action)
						   		   | PORT_EVCTRL_PID3(pin_index);
			break;
		default:
			Assert(false);
			return STATUS_ERR_INVALID_ARG;
	}
	return STATUS_OK;
}

/** @} */

#endif

#ifdef __cplusplus
}
#endif

/** @} */

/**
 * \page asfdoc_sam0_port_extra Extra Information for PORT Driver
 *
 * \section asfdoc_sam0_port_extra_acronyms Acronyms
 * Below is a table listing the acronyms used in this module, along with their
 * intended meanings.
 *
 * <table>
 *	<tr>
 *		<th>Acronym</th>
 *		<th>Description</th>
 *	</tr>
 *	<tr>
 *		<td>GPIO</td>
 *		<td>General Purpose Input/Output</td>
 *	</tr>
 *	<tr>
 *		<td>MUX</td>
 *		<td>Multiplexer</td>
 *	</tr>
 * </table>
 *
 *
 * \section asfdoc_sam0_port_extra_dependencies Dependencies
 * This driver has the following dependencies:
 *
 *  - \ref asfdoc_sam0_system_pinmux_group "System Pin Multiplexer Driver"
 *
 *
 * \section asfdoc_sam0_port_extra_errata Errata
 * There are no errata related to this driver.
 *
 *
 * \section asfdoc_sam0_port_extra_history Module History
 * An overview of the module history is presented in the table below, with
 * details on the enhancements and fixes made to the module since its first
 * release. The current version of this corresponds to the newest version in
 * the table.
 *
 * <table>
 *	<tr>
 *		<th>Changelog</th>
 *	</tr>
 *	<tr>
 *		<td>Added input event feature</td>
 *	</tr>
 *	<tr>
 *		<td>Initial release</td>
 *	</tr>
 * </table>
 */

/**
 * \page asfdoc_sam0_port_exqsg Examples for PORT Driver
 *
 * This is a list of the available Quick Start guides (QSGs) and example
 * applications for \ref asfdoc_sam0_port_group. QSGs are simple examples with
 * step-by-step instructions to configure and use this driver in a selection of
 * use cases. Note that a QSG can be compiled as a standalone application or be
 * added to the user application.
 *
 *  - \subpage asfdoc_sam0_port_basic_use_case
 *
 * \page asfdoc_sam0_port_document_revision_history Document Revision History
 *
 * <table>
 *	<tr>
 *		<th>Doc. Rev.</td>
 *		<th>Date</td>
 *		<th>Comments</td>
 *	</tr>
 *	<tr>
 *		<td>42113E</td>
 *		<td>12/2015</td>
 *		<td>Added input event feature.
 *			Added support for SAM L21/L22, SAM C21, SAM D09, SAMR30 and SAM DA1.</td>
 *	</tr>
 *	<tr>
 *		<td>42113D</td>
 *		<td>12/2014</td>
 *		<td>Added support for SAM R21 and SAM D10/D11</td>
 *	</tr>
 *	<tr>
 *		<td>42113C</td>
 *		<td>01/2014</td>
 *		<td>Added support for SAM D21</td>
 *	</tr>
 *	<tr>
 *		<td>42113B</td>
 *		<td>06/2013</td>
 *		<td>Corrected documentation typos</td>
 *	</tr>
 *	<tr>
 *		<td>42113A</td>
 *		<td>06/2013</td>
 *		<td>Initial document release</td>
 *	</tr>
 * </table>
 */

#endif