blob: 293a1e4bedd8e5be9065299a72d74b3b4868c20f (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
|
;*******************************************************************************
; (c) Copyright 2015 Microsemi SoC Products Group. All rights reserved.
; SmartFusion2 scatter file for relocating code to external RAM.
;
; SVN $Revision: 7419 $
; SVN $Date: 2015-05-15 16:50:21 +0100 (Fri, 15 May 2015) $
;
; * Some current (April 2015) dev kit memory map possibilities are
; * --Type-------Device-----------address start---address end----size---Dbus--RAM IC-------SF2--Comment---------------
; * --eNVM-------M2S010-----------0x60000000------0x6007FFFF-----256KB---------------------010------------------------
; * --eNVM-------M2S090-----------0x60000000------0x6007FFFF-----512KB---------------------090------------------------
; * --eSRAM------M2Sxxx-----------0x20000000------0x2000FFFF-----64KB----------------------xxx--All have same amount--
; * --eSRAM------M2Sxxx-----------0x20000000------0x20013FFF-----80KB----------------------xxx--If ECC/SECDED not used
; * --Fabric-----M2S010-----------0x30000000------0x6007FFFF-----400Kb---------------------010--note-K bits-----------
; * --Fabric-----M2S090-----------0x30000000------0x6007FFFF-----2074Kb--------------------090--note-K bits-----------
; * --LPDDR------STARTER-KIT------0xA0000000------0xA3FFFFFF-----64MB---16--MT46H32M16-----050------------------------
; * --LPDDR------484-STARTER-KIT--0xA0000000------0xA3FFFFFF-----64MB---16--MT46H32M16-----010------------------------
; * --LPDDR------SEC-EVAL-KIT-----0xA0000000------0xA3FFFFFF-----64MB---16--MT46H32M16LF---090--Security eval kit-----
; * --DDR3-------ADevKit----------0xA0000000------0xBFFFFFFF-----1GB----32--MT41K256M8DA---150------------------------
; * --Some older physical memory map possibilities are
; * --Type-------location---------address start---address end----size---Dbus---RAM IC------SF2--Comment--------------
; * --LPDDR------EVAL KIT---------0xA0000000------0xA3FFFFFF-----64MB-=-16--MT46H32M16LF---025--Eval Kit--------------
; * --DDR3-------DevKit-----------0xA0000000------0xAFFFFFFF-----512MB--16--MT41K256M8DA---050------------------------
;
; Example linker scripts use lowest practicl values so will work accross dev kits
; eNVM=256KB eRAM=64KB External memory = 64MB
FLASH_LOAD 0x60000000 0x40000
{
; All code required on start-up located here before relocation has occured
ER_RO 0x60000000 0x40000
{
*.o (RESET, +First)
*(InRoot$$Sections)
startup_m2sxxx.o
system_m2sxxx.o
sys_config.o
low_level_init.o
sys_config_SERDESIF_?.o
mscc_post_hw_cfg_init.o
ecc_error_handler.o
}
; MDDR_RAM 0xA0000000 0x4000000
; -MDDR is mapped to address space from 0 on startup
; This allows the use of cache which is restriced to this area.
; Code is copied to RAM_EXEC space on startup by boot code.
RAM_EXEC 0x00000000 0x00040000
{
.ANY (+RO)
}
; Heap size is defined in startup_m2sxxx.s
; Heap will be added after RW data in ER_RW unless explicitly
; allocated a meemory region in .sct file
; Stack size is defined in startup_m2sxxx.s
; Stack will be added after heap in ER_RW unless explicitly
; allocated a memory region in .sct file as is the case below
STACKS 0x20000000 UNINIT
{
startup_m2sxxx.o (STACK)
}
; All internal RAM has been allocatd to the stack
; INTERNAL_RAM 0x20008000 0x10000
; {
; .ANY (+RW +ZI)
; }
; MDDR_RAM 0xA0000000 0x4000000 So use top half of this for RW data
; Bottom half has been assigned to R only code already
ER_RW 0xA2000000 0x2000000
{
.ANY (+RW +ZI)
}
}
|
