| Age | Commit message (Collapse) | Author |
|---|
|
The per-edit disclosure named the product and model, so every agent and every
model version appended another line. 74 files carried two to four of them, and
the same five products had accumulated 13 spellings -- Copilot against GitHub
Copilot, Claude Sonnet 4.6 against claude-sonnet-4.6, four spellings of Codex.
Twenty assembly lines carried a doubled comment marker, `; //` or `@ //`.
Every file now carries exactly one line, fixed text naming no product:
Portions of this file were generated with AI assistance.
It is written with the comment character that file already uses, so the `;`
and `@` assembly files keep theirs and the doubled markers are gone. Precise
attribution stays on the commit, where the Assisted-by trailer is per-change,
dated and attached to the diff it describes. A header line cannot hold that
record honestly, because the code it names gets rewritten and the line stays.
A file-level flag answers whether; the history answers who.
Comment-only. 455 files, 455 insertions and 574 deletions: every removed line
was a disclosure line, every added line is the fixed text, and no file is left
with zero or with more than one. `scripts/check_ports.sh` passes, including the
reproducibility check that would catch a ports_arch master and its generated
copies drifting apart. Recompiled against dev, every file that builds without a
vendor toolchain gives a byte-identical object: 19 of 19 C files under common,
100 of 100 GNU assembly files, and all 16 assemblable files whose comment
marker changed. The 10 remaining marker changes are ac5 and IAR sources where
`;` already started the comment and only the redundant `//` was removed.
Assisted-by: Claude Code (Opus 5) <[email protected]>
|
|
the Cortex-M low-level initialization (#714)
_tx_initialize_low_level wrote VTOR and derived _tx_thread_system_stack_ptr from
the reset vector on every Cortex-M port. Programming VTOR is the job of the
low-level startup code that runs before the kernel is entered, and doing it again
inside ThreadX silently overrode a vector table that the application, a
bootloader or a firmware update had already installed. It also forced every
application to export a vector table symbol that the kernel itself never needed.
_tx_thread_system_stack_ptr is never read by any Cortex-M port, so the value
copied out of the reset vector served no purpose.
Both blocks are removed from all Cortex-M ports, together with the now-unused
symbol declarations. The GreenHills files keep the NVIC base address load that
the removed block used to leave in r0 for the SysTick setup that follows.
Applications that relied on ThreadX programming VTOR must now set it in their
startup code. The bundled examples link their vector table at address zero and
run on the reset default.
Fixes #370
Assisted-by: Copilot (Opus 5) <[email protected]>
|
|
no longer get warnings from ThreadX headers (#713)
* Marked every published ThreadX include directory as SYSTEM so applications no longer get warnings from ThreadX headers
Commit 8c3c08f added the SYSTEM keyword to the target_include_directories
call in common/CMakeLists.txt, but the same call in every port, in the
SMP common directory's consumers, in the POSIX and FreeRTOS compatibility
layers, and for the generated tx_user.h directory was left unchanged.
A consumer building with a strict warning set therefore still saw
diagnostics coming from tx_port.h and from the compatibility layer
headers, which is exactly what the original change set out to avoid.
Added the SYSTEM keyword to all of those calls so CMake emits -isystem
rather than -I for every directory holding a ThreadX public header. The
ARMv7-M, ARMv8-M, ARMv7-A and ARMv8-A architecture sources under
ports_arch were updated alongside the ports they generate, keeping the
two in step.
Directories that are PRIVATE to an example or test build were left as
they are, since nothing is published from them.
Fixes #290
Assisted-by: Copilot (Opus 5) <[email protected]>
* Stopped apt-get update being a gate it was never meant to be
apt-get update fails if any configured repository serves a bad index,
including ones this project never reads. The GitHub runner image carries
Google's and Microsoft's apt repositories, and a Hash Sum mismatch from
Google's, their CDN caught mid-publish with the index and the Release
file eight hours apart, failed all three attempts and turned a run red
over a browser nobody was installing.
Made a failed update warn and carry on, leaving apt-get install as the
gate. Nothing is weakened by that: the install still exits on a package
it cannot find, so an unreachable archive still stops the script, one
step later and naming the package it could not get, which is a better
diagnostic than a hash mismatch in a repository nobody asked for.
Disabling third-party sources before updating would keep the update
strict, but this script also runs on a contributor's own machine, and
rewriting someone's apt configuration to suit CI would be worse than
tolerating a stale index for an archive we do not read.
Assisted-by: Copilot (Opus 5) <[email protected]>
|
|
(#711)
The idle loop in _tx_thread_schedule masks interrupts before re-reading
_tx_thread_execute_ptr, so that an interrupt cannot make a thread ready
between that read and the WFI and then be lost. With PRIMASK that is safe:
the architecture excludes PRIMASK from the WFI wake-up condition, so the
interrupt still wakes the processor and is taken as soon as the loop
re-enables interrupts.
BASEPRI is not excluded. When TX_PORT_USE_BASEPRI is defined, the mask
written at the top of the loop is still in place at the WFI, so any
interrupt at or below TX_PORT_BASEPRI fails to wake the processor at all.
On a system where every interrupt is managed by ThreadX, that is every
interrupt, and the processor stays in WFI or in the low power mode entered
by tx_low_power_enter until something outside the mask happens.
Set PRIMASK and clear BASEPRI for the duration of the WFI, then restore
BASEPRI and clear PRIMASK. Interrupts remain masked across the whole
window, so the original race is still closed, but the wake-up condition is
now evaluated with BASEPRI clear and any enabled interrupt can end the wait.
A pending interrupt is taken at the CPSIE i, or at the existing unmask
further down the loop if it falls below TX_PORT_BASEPRI.
The change is made in the ARMv7-M and ARMv8-M sources under ports_arch,
including the module manager, and propagated to the generated ports with
the copy scripts. The ghs and keil ports do not implement
TX_PORT_USE_BASEPRI, and Cortex-M0/M0+/M23 have no BASEPRI register, so
those ports are unaffected.
Verified by assembling every patched GNU port for Cortex-M3, M4, M7, M33,
M55 and M85, with and without TX_PORT_USE_BASEPRI, TX_LOW_POWER and
TX_ENABLE_EXECUTION_CHANGE_NOTIFY, and by checking the disassembly of the
idle loop.
Fixes #279
Assisted-by: Copilot (Opus 5) <[email protected]>
|
|
The Cortex-M ports under ports/ are generated. scripts/copy_armv7_m.sh copies
one tx_port.h and the per tool sources to fifteen M3, M4 and M7 targets, and
scripts/copy_armv8_m.sh does the same for nine M33, M55 and M85 targets. The
ports_arch_check workflow runs both scripts and fails if the tree is not
reproducible, so those copies are meant never to be edited directly.
They were. Every Cortex-M fix since #523 was applied to the generated copies
and not to the source, so the source fell behind and the check went red:
running the three scripts on dev changes 35 files. The check triggers only on
pull requests targeting master, which is why nothing caught it while the fixes
were merged into dev.
Left alone, the next run of these scripts would have reverted three separate
pieces of work: the memory barriers and clobbers from #523, the correction of
the IAR assembly header to use the assembler's own comment syntax, and the move
of tx_initialize_low_level.S into example_build for the M33, M55 and M85 GNU
ports from #514.
Bring the sources up to what the ports carry today, and regenerate. Two
behavioural changes come with that, both deliberate. The barriers from #523
reach the ac5 and keil variants of M3, M4 and M7, which were outside the scope
of that fix and never received it. The barrier that follows restoring the
interrupt posture, which #523 gave only to the GNU ports because GNU was the
only toolchain that could be tested, now applies to every tool; the identical
asm statement already shipped in the AC6 and IAR ports, so this adds a pipeline
flush rather than any new compiler exposure.
Regenerating also drops a stray #endif at the end of the Cortex-M85 IAR
tx_port.h, added by #523, which left that header with one more #endif than #if
and unable to compile. Every other ARMv8-M port was balanced.
Verified that the scripts are idempotent afterwards, that ports_arch_check
would pass, that no port loses a barrier or a clobber, that every regenerated
header is preprocessor balanced, and that every Cortex-M port covered by the
two scripts now carries the entry barrier.
Assisted-by: Claude Code (Opus 5) <[email protected]>
|
|
Use explicit immediate syntax when clearing BASEPRI in GNU and AC6 Cortex-M scheduler assembly.
Co-authored-by: Codex <[email protected]>
|
|
* Add SysTick counter reset in Cortex-M ports
The SysTick counter value (SYST_CVR @0xE000E018) is indeterminate after
reset. Without clearing it prior to enabling the counter, the first tick
interval becomes unpredictable.
* Fixed missing comment and added generated-by header in Cortex-M0/AC6 port
Added the missing inline comment on the LDR r1, =0 instruction
(Build value for SysTick reset) and the required AI-generated
attribution comment under the copyright header.
---------
Co-authored-by: Frédéric Desbiens <[email protected]>
Co-authored-by: Copilot <[email protected]>
|
|
Applied the standard MIT license header to all project-owned C, header,
assembly, shell, and Python files that were missing a copyright notice.
Third-party, toolchain startup, and auto-generated files were excluded.
Co-authored-by: Copilot <[email protected]>
|
|
* Updated version number constants
* Removed revision history from all files
* Added Eclipse ThreadX contributors' copyright header
|
|
|
|
* Release ARMv7-M and ARMv8-M architecture ports
* Add a pipeline to check ports_arch
|
