bsp: Add STM32U083C-DK board

Signed-off-by: Mengsk <[email protected]>

10 files changed, 1167 insertions, 1 deletions

diff --git a/hw/bsp/stm32u0/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/stm32u0/FreeRTOSConfig/FreeRTOSConfig.h
new file mode 100644
index 000000000..b63275276
--- /dev/null
+++ b/hw/bsp/stm32u0/FreeRTOSConfig/FreeRTOSConfig.h
@@ -0,0 +1,149 @@
+/*
+ * FreeRTOS Kernel V10.0.0
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software. If you wish to use our Amazon
+ * FreeRTOS name, please do so in a fair use way that does not cause confusion.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
+
+
+#ifndef FREERTOS_CONFIG_H
+#define FREERTOS_CONFIG_H
+
+/*-----------------------------------------------------------
+ * Application specific definitions.
+ *
+ * These definitions should be adjusted for your particular hardware and
+ * application requirements.
+ *
+ * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE
+ * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE.
+ *
+ * See http://www.freertos.org/a00110.html.
+ *----------------------------------------------------------*/
+
+// skip if included from IAR assembler
+#ifndef __IASMARM__
+  #include "stm32u0xx.h"
+#endif
+
+/* Cortex M23/M33 port configuration. */
+#define configENABLE_MPU                        0
+#define configENABLE_FPU                        0
+#define configENABLE_TRUSTZONE                  0
+#define configMINIMAL_SECURE_STACK_SIZE         (1024)
+
+#define configUSE_PREEMPTION                    1
+#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0
+#define configCPU_CLOCK_HZ                      SystemCoreClock
+#define configTICK_RATE_HZ                      ( 1000 )
+#define configMAX_PRIORITIES                    ( 5 )
+#define configMINIMAL_STACK_SIZE                ( 200 )
+#define configTOTAL_HEAP_SIZE                   ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 )
+#define configMAX_TASK_NAME_LEN                 16
+#define configUSE_16_BIT_TICKS                  0
+#define configIDLE_SHOULD_YIELD                 1
+#define configUSE_MUTEXES                       1
+#define configUSE_RECURSIVE_MUTEXES             1
+#define configUSE_COUNTING_SEMAPHORES           1
+#define configQUEUE_REGISTRY_SIZE               4
+#define configUSE_QUEUE_SETS                    0
+#define configUSE_TIME_SLICING                  0
+#define configUSE_NEWLIB_REENTRANT              0
+#define configENABLE_BACKWARD_COMPATIBILITY     1
+#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP   0
+
+#define configSUPPORT_STATIC_ALLOCATION         1
+#define configSUPPORT_DYNAMIC_ALLOCATION        0
+
+/* Hook function related definitions. */
+#define configUSE_IDLE_HOOK                    0
+#define configUSE_TICK_HOOK                    0
+#define configUSE_MALLOC_FAILED_HOOK           0 // cause nested extern warning
+#define configCHECK_FOR_STACK_OVERFLOW         2
+#define configCHECK_HANDLER_INSTALLATION       0
+
+/* Run time and task stats gathering related definitions. */
+#define configGENERATE_RUN_TIME_STATS          0
+#define configRECORD_STACK_HIGH_ADDRESS        1
+#define configUSE_TRACE_FACILITY               1 // legacy trace
+#define configUSE_STATS_FORMATTING_FUNCTIONS   0
+
+/* Co-routine definitions. */
+#define configUSE_CO_ROUTINES                  0
+#define configMAX_CO_ROUTINE_PRIORITIES        2
+
+/* Software timer related definitions. */
+#define configUSE_TIMERS                       1
+#define configTIMER_TASK_PRIORITY              (configMAX_PRIORITIES-2)
+#define configTIMER_QUEUE_LENGTH               32
+#define configTIMER_TASK_STACK_DEPTH           configMINIMAL_STACK_SIZE
+
+/* Optional functions - most linkers will remove unused functions anyway. */
+#define INCLUDE_vTaskPrioritySet               0
+#define INCLUDE_uxTaskPriorityGet              0
+#define INCLUDE_vTaskDelete                    0
+#define INCLUDE_vTaskSuspend                   1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY
+#define INCLUDE_xResumeFromISR                 0
+#define INCLUDE_vTaskDelayUntil                1
+#define INCLUDE_vTaskDelay                     1
+#define INCLUDE_xTaskGetSchedulerState         0
+#define INCLUDE_xTaskGetCurrentTaskHandle      1
+#define INCLUDE_uxTaskGetStackHighWaterMark    0
+#define INCLUDE_xTaskGetIdleTaskHandle         0
+#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0
+#define INCLUDE_pcTaskGetTaskName              0
+#define INCLUDE_eTaskGetState                  0
+#define INCLUDE_xEventGroupSetBitFromISR       0
+#define INCLUDE_xTimerPendFunctionCall         0
+
+/* FreeRTOS hooks to NVIC vectors */
+#define xPortPendSVHandler    PendSV_Handler
+#define xPortSysTickHandler   SysTick_Handler
+#define vPortSVCHandler       SVC_Handler
+
+//--------------------------------------------------------------------+
+// Interrupt nesting behavior configuration.
+//--------------------------------------------------------------------+
+
+// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header
+#define configPRIO_BITS       2
+
+/* The lowest interrupt priority that can be used in a call to a "set priority" function. */
+#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY			  ((1<<configPRIO_BITS) - 1)
+
+/* The highest interrupt priority that can be used by any interrupt service
+routine that makes calls to interrupt safe FreeRTOS API functions.  DO NOT CALL
+INTERRUPT SAFE FREERTOS API FUNCTIONS FROM ANY INTERRUPT THAT HAS A HIGHER
+PRIORITY THAN THIS! (higher priorities are lower numeric values. */
+#define configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY	2
+
+/* Interrupt priorities used by the kernel port layer itself.  These are generic
+to all Cortex-M ports, and do not rely on any particular library functions. */
+#define configKERNEL_INTERRUPT_PRIORITY 		          ( configLIBRARY_LOWEST_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) )
+
+/* !!!! configMAX_SYSCALL_INTERRUPT_PRIORITY must not be set to zero !!!!
+See http://www.FreeRTOS.org/RTOS-Cortex-M3-M4.html. */
+#define configMAX_SYSCALL_INTERRUPT_PRIORITY 	        ( configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) )
+
+#endif
diff --git a/hw/bsp/stm32u0/boards/stm32u083cdk/STM32U083MCTx_FLASH.ld b/hw/bsp/stm32u0/boards/stm32u083cdk/STM32U083MCTx_FLASH.ld
new file mode 100644
index 000000000..a862acc12
--- /dev/null
+++ b/hw/bsp/stm32u0/boards/stm32u083cdk/STM32U083MCTx_FLASH.ld
@@ -0,0 +1,176 @@
+/**
+  ******************************************************************************
+  * @file      LinkerScript.ld
+  * @author    Auto-generated by STM32CubeIDE
+  * @brief     Linker script for STM32U083MCTx Device from STM32U0 series
+  *            256KBytes FLASH
+  *            40KBytes RAM
+  *
+  *            Set heap size, stack size and stack location according
+  *            to application requirements.
+  *
+  *            Set memory bank area and size if external memory is used
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2023 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200;  /* required amount of heap */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Memories definition */
+MEMORY
+{
+  RAM    (xrw)    : ORIGIN = 0x20000000,   LENGTH = 40K
+  FLASH    (rx)    : ORIGIN = 0x8000000,   LENGTH = 256K
+}
+
+/* Sections */
+SECTIONS
+{
+  /* The startup code into "FLASH" Rom type memory */
+  .isr_vector :
+  {
+    . = ALIGN(4);
+    KEEP(*(.isr_vector)) /* Startup code */
+    . = ALIGN(4);
+  } >FLASH
+
+  /* The program code and other data into "FLASH" Rom type memory */
+  .text :
+  {
+    . = ALIGN(4);
+    *(.text)           /* .text sections (code) */
+    *(.text*)          /* .text* sections (code) */
+    *(.glue_7)         /* glue arm to thumb code */
+    *(.glue_7t)        /* glue thumb to arm code */
+    *(.eh_frame)
+
+    KEEP (*(.init))
+    KEEP (*(.fini))
+
+    . = ALIGN(4);
+    _etext = .;        /* define a global symbols at end of code */
+  } >FLASH
+
+  /* Constant data into "FLASH" Rom type memory */
+  .rodata :
+  {
+    . = ALIGN(4);
+    *(.rodata)         /* .rodata sections (constants, strings, etc.) */
+    *(.rodata*)        /* .rodata* sections (constants, strings, etc.) */
+    . = ALIGN(4);
+  } >FLASH
+
+  .ARM.extab   : {
+    . = ALIGN(4);
+    *(.ARM.extab* .gnu.linkonce.armextab.*)
+    . = ALIGN(4);
+  } >FLASH
+
+  .ARM : {
+    . = ALIGN(4);
+    __exidx_start = .;
+    *(.ARM.exidx*)
+    __exidx_end = .;
+    . = ALIGN(4);
+  } >FLASH
+
+  .preinit_array     :
+  {
+    . = ALIGN(4);
+    PROVIDE_HIDDEN (__preinit_array_start = .);
+    KEEP (*(.preinit_array*))
+    PROVIDE_HIDDEN (__preinit_array_end = .);
+    . = ALIGN(4);
+  } >FLASH
+
+  .init_array :
+  {
+    . = ALIGN(4);
+    PROVIDE_HIDDEN (__init_array_start = .);
+    KEEP (*(SORT(.init_array.*)))
+    KEEP (*(.init_array*))
+    PROVIDE_HIDDEN (__init_array_end = .);
+    . = ALIGN(4);
+  } >FLASH
+
+  .fini_array :
+  {
+    . = ALIGN(4);
+    PROVIDE_HIDDEN (__fini_array_start = .);
+    KEEP (*(SORT(.fini_array.*)))
+    KEEP (*(.fini_array*))
+    PROVIDE_HIDDEN (__fini_array_end = .);
+    . = ALIGN(4);
+  } >FLASH
+
+  /* Used by the startup to initialize data */
+  _sidata = LOADADDR(.data);
+
+  /* Initialized data sections into "RAM" Ram type memory */
+  .data :
+  {
+    . = ALIGN(4);
+    _sdata = .;        /* create a global symbol at data start */
+    *(.data)           /* .data sections */
+    *(.data*)          /* .data* sections */
+    *(.RamFunc)        /* .RamFunc sections */
+    *(.RamFunc*)       /* .RamFunc* sections */
+
+    . = ALIGN(4);
+    _edata = .;        /* define a global symbol at data end */
+
+  } >RAM AT> FLASH
+
+  /* Uninitialized data section into "RAM" Ram type memory */
+  . = ALIGN(4);
+  .bss :
+  {
+    /* This is used by the startup in order to initialize the .bss section */
+    _sbss = .;         /* define a global symbol at bss start */
+    __bss_start__ = _sbss;
+    *(.bss)
+    *(.bss*)
+    *(COMMON)
+
+    . = ALIGN(4);
+    _ebss = .;         /* define a global symbol at bss end */
+    __bss_end__ = _ebss;
+  } >RAM
+
+  /* User_heap_stack section, used to check that there is enough "RAM" Ram  type memory left */
+  ._user_heap_stack :
+  {
+    . = ALIGN(8);
+    PROVIDE ( end = . );
+    PROVIDE ( _end = . );
+    . = . + _Min_Heap_Size;
+    . = . + _Min_Stack_Size;
+    . = ALIGN(8);
+  } >RAM
+
+  /* Remove information from the compiler libraries */
+  /DISCARD/ :
+  {
+    libc.a ( * )
+    libm.a ( * )
+    libgcc.a ( * )
+  }
+
+  .ARM.attributes 0 : { *(.ARM.attributes) }
+}
\ No newline at end of file
diff --git a/hw/bsp/stm32u0/boards/stm32u083cdk/board.cmake b/hw/bsp/stm32u0/boards/stm32u083cdk/board.cmake
new file mode 100644
index 000000000..b927a7626
--- /dev/null
+++ b/hw/bsp/stm32u0/boards/stm32u083cdk/board.cmake
@@ -0,0 +1,10 @@
+set(MCU_VARIANT stm32u083xx)
+set(JLINK_DEVICE stm32u083mc)
+
+set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32U083MCTx_FLASH.ld)
+
+function(update_board TARGET)
+  target_compile_definitions(${TARGET} PUBLIC
+    STM32U083xx
+    )
+endfunction()
\ No newline at end of file
diff --git a/hw/bsp/stm32u0/boards/stm32u083cdk/board.h b/hw/bsp/stm32u0/boards/stm32u083cdk/board.h
new file mode 100644
index 000000000..2f02b24d3
--- /dev/null
+++ b/hw/bsp/stm32u0/boards/stm32u083cdk/board.h
@@ -0,0 +1,129 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+/* metadata:
+   name: STM32U083C-DK Discovery Kit
+   url: https://www.st.com/en/evaluation-tools/stm32u083c-dk.html
+*/
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+// LED - using PA5 (Blue LED from CubeMX)
+#define LED_PORT              GPIOA
+#define LED_PIN               GPIO_PIN_5
+#define LED_STATE_ON          1
+
+// Button - using PC2 (from CubeMX generated code)
+#define BUTTON_PORT           GPIOC
+#define BUTTON_PIN            GPIO_PIN_2
+#define BUTTON_STATE_ACTIVE   0  // Active low (pressed = 0)
+
+// UART - using USART2 on PA2/PA3 (VCP TX/RX from CubeMX)
+#define UART_DEV              USART2
+#define UART_CLK_EN           __HAL_RCC_USART2_CLK_ENABLE
+#define UART_GPIO_PORT        GPIOA
+#define UART_GPIO_AF          GPIO_AF7_USART2
+#define UART_TX_PIN           GPIO_PIN_2
+#define UART_RX_PIN           GPIO_PIN_3
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32u0_clock_init(void)
+{
+  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+  RCC_CRSInitTypeDef RCC_CRSInitStruct = {0};
+  RCC_PeriphCLKInitTypeDef  PeriphClkInit = {0};
+
+  /** Configure the main internal regulator output voltage
+  */
+  HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+  /** Initializes the RCC Oscillators according to the specified parameters
+  * in the RCC_OscInitTypeDef structure.
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_HSI48;
+  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+  RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+  RCC_OscInitStruct.PLL.PLLM = RCC_PLLM_DIV1;
+  RCC_OscInitStruct.PLL.PLLN = 8;
+  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+  RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV2;
+  RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV4;
+  HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+  /** Initializes the CPU, AHB and APB buses clocks
+  */
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+                              |RCC_CLOCKTYPE_PCLK1;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+
+  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
+
+  /** Enable the CRS clock
+  */
+  __HAL_RCC_CRS_CLK_ENABLE();
+
+  /** Configures CRS
+  */
+  RCC_CRSInitStruct.Prescaler = RCC_CRS_SYNC_DIV1;
+  RCC_CRSInitStruct.Source = RCC_CRS_SYNC_SOURCE_USB;
+  RCC_CRSInitStruct.Polarity = RCC_CRS_SYNC_POLARITY_RISING;
+  RCC_CRSInitStruct.ReloadValue = __HAL_RCC_CRS_RELOADVALUE_CALCULATE(48000000,1000);
+  RCC_CRSInitStruct.ErrorLimitValue = 34;
+  RCC_CRSInitStruct.HSI48CalibrationValue = 32;
+  HAL_RCCEx_CRSConfig(&RCC_CRSInitStruct);
+
+  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART2;
+  PeriphClkInit.Usart2ClockSelection = RCC_USART2CLKSOURCE_PCLK1;
+  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
+
+  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB;
+  PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_HSI48;
+  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
+}
+
+static inline void board_vbus_sense_init(void)
+{
+  // USB VBUS sensing not required for device-only operation
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif /* BOARD_H_ */
\ No newline at end of file
diff --git a/hw/bsp/stm32u0/boards/stm32u083cdk/board.mk b/hw/bsp/stm32u0/boards/stm32u083cdk/board.mk
new file mode 100644
index 000000000..9b1a18a43
--- /dev/null
+++ b/hw/bsp/stm32u0/boards/stm32u083cdk/board.mk
@@ -0,0 +1,12 @@
+MCU_VARIANT = stm32u083xx
+CFLAGS += \
+  -DSTM32U083xx
+
+# All source paths should be relative to the top level.
+LD_FILE = $(BOARD_PATH)/STM32U083MCTx_FLASH.ld
+
+# For flash-jlink target
+JLINK_DEVICE = STM32U083MC
+
+# flash target using on-board stlink
+flash: flash-stlink
\ No newline at end of file
diff --git a/hw/bsp/stm32u0/family.c b/hw/bsp/stm32u0/family.c
new file mode 100644
index 000000000..69fc0948e
--- /dev/null
+++ b/hw/bsp/stm32u0/family.c
@@ -0,0 +1,182 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+/* metadata:
+   manufacturer: STMicroelectronics
+*/
+
+#include "stm32u0xx_hal.h"
+#include "bsp/board_api.h"
+#include "board.h"
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void USB_DRD_FS_IRQHandler(void) {
+  tud_int_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
+#ifdef UART_DEV
+UART_HandleTypeDef UartHandle;
+#endif
+
+void board_init(void) {
+  board_stm32u0_clock_init();
+
+  // Enable All GPIOs clocks
+  __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_GPIOB_CLK_ENABLE();
+  __HAL_RCC_GPIOC_CLK_ENABLE();
+#ifdef GPIOD
+  __HAL_RCC_GPIOD_CLK_ENABLE();
+#endif
+#ifdef GPIOE
+  __HAL_RCC_GPIOE_CLK_ENABLE();
+#endif
+#ifdef GPIOF
+  __HAL_RCC_GPIOF_CLK_ENABLE();
+#endif
+#ifdef GPIOG
+  __HAL_RCC_GPIOG_CLK_ENABLE();
+#endif
+#ifdef GPIOH
+  __HAL_RCC_GPIOH_CLK_ENABLE();
+#endif
+  __HAL_RCC_PWR_CLK_ENABLE();
+
+  // LED
+  GPIO_InitTypeDef  GPIO_InitStruct;
+  GPIO_InitStruct.Pin = LED_PIN;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = GPIO_PULLUP;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+  HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+  // Button
+  GPIO_InitStruct.Pin = BUTTON_PIN;
+  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+  GPIO_InitStruct.Pull = BUTTON_STATE_ACTIVE ? GPIO_PULLDOWN : GPIO_PULLUP;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+  HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
+
+#ifdef UART_DEV
+  // UART
+  GPIO_InitStruct.Pin       = UART_TX_PIN | UART_RX_PIN;
+  GPIO_InitStruct.Mode      = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull      = GPIO_PULLUP;
+  GPIO_InitStruct.Speed     = GPIO_SPEED_FREQ_HIGH;
+  GPIO_InitStruct.Alternate = UART_GPIO_AF;
+  HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct);
+
+  UART_CLK_EN();
+  UartHandle.Instance        = UART_DEV;
+  UartHandle.Init.BaudRate   = CFG_BOARD_UART_BAUDRATE;
+  UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
+  UartHandle.Init.StopBits   = UART_STOPBITS_1;
+  UartHandle.Init.Parity     = UART_PARITY_NONE;
+  UartHandle.Init.HwFlowCtl  = UART_HWCONTROL_NONE;
+  UartHandle.Init.Mode       = UART_MODE_TX_RX;
+  UartHandle.Init.OverSampling = UART_OVERSAMPLING_16;
+  HAL_UART_Init(&UartHandle);
+#endif
+
+#if CFG_TUSB_OS == OPT_OS_FREERTOS
+  // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
+  NVIC_SetPriority(USB_DRD_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
+#endif
+
+  // USB Pins TODO double check USB clock and pin setup
+  // Configure USB DM and DP pins. This is optional, and maintained only for user guidance.
+  GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+  GPIO_InitStruct.Alternate = GPIO_AF10_USB;
+  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  // Enable VDDUSB
+  HAL_PWREx_EnableVddUSB();
+  // USB Clock enable
+  __HAL_RCC_USB_CLK_ENABLE();
+
+  board_vbus_sense_init();
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state) {
+  GPIO_PinState pin_state = (GPIO_PinState) (state ? LED_STATE_ON : (1-LED_STATE_ON));
+  HAL_GPIO_WritePin(LED_PORT, LED_PIN, pin_state);
+}
+
+uint32_t board_button_read(void) {
+  return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
+}
+
+int board_uart_read(uint8_t* buf, int len) {
+#ifdef UART_DEV
+  (void) buf; (void) len;
+  return 0;
+#else
+  return 0;
+#endif
+}
+
+int board_uart_write(void const * buf, int len) {
+#ifdef UART_DEV
+  HAL_UART_Transmit(&UartHandle, (uint8_t*)(uintptr_t) buf, len, 0xffff);
+  return len;
+#else
+  (void) buf; (void) len;
+  return 0;
+#endif
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler(void) {
+  system_ticks++;
+}
+
+uint32_t board_millis(void) {
+  return system_ticks;
+}
+#endif
+
+void HardFault_Handler(void) {
+  __asm("BKPT #0\n");
+}
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void) {
+
+}
\ No newline at end of file
diff --git a/hw/bsp/stm32u0/family.cmake b/hw/bsp/stm32u0/family.cmake
new file mode 100644
index 000000000..8d0926d9b
--- /dev/null
+++ b/hw/bsp/stm32u0/family.cmake
@@ -0,0 +1,115 @@
+include_guard()
+
+set(ST_FAMILY u0)
+set(ST_PREFIX stm32${ST_FAMILY}xx)
+
+set(ST_HAL_DRIVER ${TOP}/hw/mcu/st/stm32${ST_FAMILY}xx_hal_driver)
+set(ST_CMSIS ${TOP}/hw/mcu/st/cmsis-device-${ST_FAMILY})
+set(CMSIS_5 ${TOP}/lib/CMSIS_5)
+
+# include board specific
+include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake)
+
+# toolchain set up
+set(CMAKE_SYSTEM_CPU cortex-m0plus CACHE INTERNAL "System Processor")
+set(CMAKE_TOOLCHAIN_FILE ${TOP}/examples/build_system/cmake/toolchain/arm_${TOOLCHAIN}.cmake)
+
+set(FAMILY_MCUS STM32U0 CACHE INTERNAL "")
+
+
+#------------------------------------
+# BOARD_TARGET
+#------------------------------------
+# only need to be built ONCE for all examples
+function(add_board_target BOARD_TARGET)
+  if (TARGET ${BOARD_TARGET})
+    return()
+  endif()
+
+  # Startup & Linker script
+  set(STARTUP_FILE_GNU ${ST_CMSIS}/Source/Templates/gcc/startup_${MCU_VARIANT}.s)
+  set(STARTUP_FILE_Clang ${STARTUP_FILE_GNU})
+  set(STARTUP_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/startup_${MCU_VARIANT}.s)
+
+  string(REPLACE "stm32u" "STM32U" MCU_VARIANT_UPPER ${MCU_VARIANT})
+  if (NOT DEFINED LD_FILE_GNU)
+    set(LD_FILE_GNU ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/linker/${MCU_VARIANT_UPPER}_FLASH.ld)
+  endif ()
+  set(LD_FILE_Clang ${LD_FILE_GNU})
+  set(LD_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/linker/${MCU_VARIANT}_flash.icf)
+
+  add_library(${BOARD_TARGET} STATIC
+    ${ST_CMSIS}/Source/Templates/system_${ST_PREFIX}.c
+    ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal.c
+    ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_cortex.c
+    ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_gpio.c
+    ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_pwr_ex.c
+    ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc.c
+    ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc_ex.c
+    ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_uart.c
+    ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_uart_ex.c
+    ${STARTUP_FILE_${CMAKE_C_COMPILER_ID}}
+    )
+  target_include_directories(${BOARD_TARGET} PUBLIC
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}
+    ${CMSIS_5}/CMSIS/Core/Include
+    ${ST_CMSIS}/Include
+    ${ST_HAL_DRIVER}/Inc
+    )
+  update_board(${BOARD_TARGET})
+
+  if (CMAKE_C_COMPILER_ID STREQUAL "GNU")
+    target_link_options(${BOARD_TARGET} PUBLIC
+      "LINKER:--script=${LD_FILE_GNU}"
+      -nostartfiles
+      --specs=nosys.specs --specs=nano.specs
+      )
+  elseif (CMAKE_C_COMPILER_ID STREQUAL "Clang")
+    target_link_options(${BOARD_TARGET} PUBLIC
+      "LINKER:--script=${LD_FILE_Clang}"
+      )
+  elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR")
+    target_link_options(${BOARD_TARGET} PUBLIC
+      "LINKER:--config=${LD_FILE_IAR}"
+      )
+  endif ()
+endfunction()
+
+
+#------------------------------------
+# Functions
+#------------------------------------
+function(family_configure_example TARGET RTOS)
+  family_configure_common(${TARGET} ${RTOS})
+
+  # Board target
+  add_board_target(board_${BOARD})
+
+  #---------- Port Specific ----------
+  # These files are built for each example since it depends on example's tusb_config.h
+  target_sources(${TARGET} PUBLIC
+    # BSP
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c
+    )
+  target_include_directories(${TARGET} PUBLIC
+    # family, hw, board
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD}
+    )
+
+  # Add TinyUSB target and port source
+  family_add_tinyusb(${TARGET} OPT_MCU_STM32U0)
+  target_sources(${TARGET} PUBLIC
+    ${TOP}/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c
+    )
+  target_link_libraries(${TARGET} PUBLIC board_${BOARD})
+
+
+
+  # Flashing
+  family_add_bin_hex(${TARGET})
+  family_flash_stlink(${TARGET})
+  family_flash_jlink(${TARGET})
+endfunction()
diff --git a/hw/bsp/stm32u0/family.mk b/hw/bsp/stm32u0/family.mk
new file mode 100644
index 000000000..6c0d5a1de
--- /dev/null
+++ b/hw/bsp/stm32u0/family.mk
@@ -0,0 +1,49 @@
+ST_FAMILY = u0
+ST_CMSIS = hw/mcu/st/cmsis-device-$(ST_FAMILY)
+ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
+
+include $(TOP)/$(BOARD_PATH)/board.mk
+CPU_CORE ?= cortex-m0plus
+
+CFLAGS += \
+  -DCFG_EXAMPLE_MSC_READONLY \
+  -DCFG_EXAMPLE_VIDEO_READONLY \
+  -DCFG_TUSB_MCU=OPT_MCU_STM32U0
+
+# mcu driver cause following warnings
+CFLAGS_GCC += \
+  -flto \
+	-Wno-error=unused-parameter \
+	-Wno-error=redundant-decls \
+	-Wno-error=cast-align \
+	-Wno-error=maybe-uninitialized \
+
+CFLAGS_CLANG += \
+  -Wno-error=parentheses-equality
+
+LDFLAGS_GCC += \
+  -nostdlib -nostartfiles \
+  --specs=nosys.specs --specs=nano.specs
+
+SRC_C += \
+  src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c \
+  $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c
+
+INC += \
+	$(TOP)/$(BOARD_PATH) \
+  $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
+  $(TOP)/$(ST_CMSIS)/Include \
+  $(TOP)/$(ST_HAL_DRIVER)/Inc
+
+# Startup
+SRC_S_GCC += $(ST_CMSIS)/Source/Templates/gcc/startup_${MCU_VARIANT}.s
+SRC_S_IAR += $(ST_CMSIS)/Source/Templates/iar/startup_${MCU_VARIANT}.s
+
+# Linker
+LD_FILE_IAR ?= $(ST_CMSIS)/Source/Templates/iar/linker/$(MCU_VARIANT)_flash.icf
\ No newline at end of file
diff --git a/hw/bsp/stm32u0/stm32u0xx_hal_conf.h b/hw/bsp/stm32u0/stm32u0xx_hal_conf.h
new file mode 100644
index 000000000..1cd9b5a91
--- /dev/null
+++ b/hw/bsp/stm32u0/stm32u0xx_hal_conf.h
@@ -0,0 +1,338 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    stm32u0xx_hal_conf.h
+  * @author  MCD Application Team
+  * @brief   HAL configuration file.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2023 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32U0xx_HAL_CONF_H
+#define __STM32U0xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+  * @brief This is the list of modules to be used in the HAL driver
+  */
+
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED   */
+/* #define HAL_COMP_MODULE_ENABLED   */
+/* #define HAL_CRC_MODULE_ENABLED   */
+/* #define HAL_CRS_MODULE_ENABLED   */
+/* #define HAL_CRYP_MODULE_ENABLED   */
+/* #define HAL_DAC_MODULE_ENABLED   */
+/* #define HAL_I2C_MODULE_ENABLED   */
+/* #define HAL_IRDA_MODULE_ENABLED   */
+/* #define HAL_IWDG_MODULE_ENABLED   */
+/* #define HAL_LCD_MODULE_ENABLED   */
+/* #define HAL_LPTIM_MODULE_ENABLED   */
+/* #define HAL_OPAMP_MODULE_ENABLED   */
+#define HAL_PCD_MODULE_ENABLED
+/* #define HAL_RNG_MODULE_ENABLED   */
+/* #define HAL_RTC_MODULE_ENABLED   */
+/* #define HAL_SPI_MODULE_ENABLED   */
+/* #define HAL_SMARTCARD_MODULE_ENABLED   */
+/* #define HAL_TIM_MODULE_ENABLED   */
+/* #define HAL_TSC_MODULE_ENABLED   */
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED   */
+/* #define HAL_WWDG_MODULE_ENABLED   */
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_EXTI_MODULE_ENABLED
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_CORTEX_MODULE_ENABLED
+
+/* ########################## Oscillator Values adaptation ####################*/
+/**
+  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSE is used as system clock source, directly or through the PLL).
+  */
+#if !defined  (HSE_VALUE)
+  #define HSE_VALUE              4000000U /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined  (HSE_STARTUP_TIMEOUT)
+  #define HSE_STARTUP_TIMEOUT    100U   /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief Internal Multiple Speed oscillator (MSI) default value.
+  *        This value is the default MSI range value after Reset.
+  */
+#if !defined  (MSI_VALUE)
+  #define MSI_VALUE              4000000U /*!< Value of the Internal oscillator in Hz*/
+#endif /* MSI_VALUE */
+
+/**
+ * @brief Internal Multiple Speed oscillator (MSI) default value.
+ *        This value is the default MSI range value after Reset.
+ */
+#if !defined  (MSI32_VALUE)
+#define MSI32_VALUE            32000000U /*!< Value of the Internal oscillator in Hz*/
+#endif /* MSI32_VALUE */
+
+/**
+  * @brief Internal High Speed oscillator (HSI) value.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSI is used as system clock source, directly or through the PLL).
+  */
+#if !defined  (HSI_VALUE)
+  #define HSI_VALUE              16000000U /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+  * @brief Internal High Speed oscillator (HSI48) value for USB FS and RNG.
+  *        This internal oscillator is mainly dedicated to provide a high precision clock to
+  *        the USB peripheral by means of a special Clock Recovery System (CRS) circuitry.
+  *        When the CRS is not used, the HSI48 RC oscillator runs on it default frequency
+  *        which is subject to manufacturing process variations.
+  */
+#if !defined  (HSI48_VALUE)
+  #define HSI48_VALUE             48000000U /*!< Value of the Internal High Speed oscillator for USB FS/RNG in Hz.
+                                               The real value my vary depending on manufacturing process variations.*/
+#endif /* HSI48_VALUE */
+
+/**
+  * @brief Internal Low Speed oscillator (LSI) value.
+  */
+#if !defined  (LSI_VALUE)
+  #define LSI_VALUE  32000U     /*!< LSI Typical Value in Hz*/
+#endif /* LSI_VALUE */                     /*!< Value of the Internal Low Speed oscillator in Hz
+                                                The real value may vary depending on the variations
+                                                in voltage and temperature.*/
+/**
+  * @brief External Low Speed oscillator (LSE) value.
+  *        This value is used by the UART, RTC HAL module to compute the system frequency
+  */
+#if !defined  (LSE_VALUE)
+  #define LSE_VALUE              32768U    /*!< Value of the External oscillator in Hz*/
+#endif /* LSE_VALUE */
+
+#if !defined  (LSE_STARTUP_TIMEOUT)
+  #define LSE_STARTUP_TIMEOUT    5000U   /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+   ===  you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+  * @brief This is the HAL system configuration section
+  */
+
+#define  VDD_VALUE                    3300U /*!< Value of VDD in mv */
+#define  TICK_INT_PRIORITY            (3U)    /*!< tick interrupt priority (lowest by default) */
+#define  USE_RTOS                     0U
+#define  PREFETCH_ENABLE              0U
+#define  INSTRUCTION_CACHE_ENABLE     1U
+
+/* ########################## Assert Selection ############################## */
+/**
+  * @brief Uncomment the line below to expanse the "assert_param" macro in the
+  *        HAL drivers code
+  */
+
+/* #define USE_FULL_ASSERT    1U */
+
+/* ################## Register callback feature configuration ############### */
+/**
+  * @brief Set below the peripheral configuration  to "1U" to add the support
+  *        of HAL callback registration/unregistration feature for the HAL
+  *        driver(s). This allows user application to provide specific callback
+  *        functions thanks to HAL_PPP_RegisterCallback() rather than overwriting
+  *        the default weak callback functions (see each stm32n6xx_hal_ppp.h file
+  *        for possible callback identifiers defined in HAL_PPP_CallbackIDTypeDef
+  *        for each PPP peripheral).
+  */
+#define  USE_HAL_ADC_REGISTER_CALLBACKS        0U /* ADC register callback disabled       */
+#define  USE_HAL_CRYP_REGISTER_CALLBACKS       0U /* CRYP register callback disabled      */
+#define  USE_HAL_DAC_REGISTER_CALLBACKS        0U /* DAC register callback disabled       */
+#define  USE_HAL_I2C_REGISTER_CALLBACKS        0U /* I2C register callback disabled       */
+#define  USE_HAL_IWDG_REGISTER_CALLBACKS       0U /* IWDG register callback disabled      */
+#define  USE_HAL_IRDA_REGISTER_CALLBACKS       0U /* IRDA register callback disabled      */
+#define  USE_HAL_LPTIM_REGISTER_CALLBACKS      0U /* LPTIM register callback disabled     */
+#define  USE_HAL_LCD_REGISTER_CALLBACKS        0U /* LCD register callback disabled      */
+#define  USE_HAL_PCD_REGISTER_CALLBACKS        0U /* PCD register callback disabled       */
+#define  USE_HAL_RNG_REGISTER_CALLBACKS        0U /* RNG register callback disabled       */
+#define  USE_HAL_RTC_REGISTER_CALLBACKS        0U /* RTC register callback disabled       */
+#define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS  0U /* SMARTCARD register callback disabled */
+#define  USE_HAL_SPI_REGISTER_CALLBACKS        0U /* SPI register callback disabled       */
+#define  USE_HAL_TIM_REGISTER_CALLBACKS        0U /* TIM register callback disabled       */
+#define  USE_HAL_UART_REGISTER_CALLBACKS       0U /* UART register callback disabled      */
+#define  USE_HAL_USART_REGISTER_CALLBACKS      0U /* USART register callback disabled     */
+#define  USE_HAL_WWDG_REGISTER_CALLBACKS       0U /* WWDG register callback disabled      */
+
+/* Includes ------------------------------------------------------------------*/
+/**
+  * @brief Include module's header file
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+#include "stm32u0xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+#include "stm32u0xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+#include "stm32u0xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+#include "stm32u0xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+#include "stm32u0xx_hal_adc.h"
+#include "stm32u0xx_hal_adc_ex.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_COMP_MODULE_ENABLED
+#include "stm32u0xx_hal_comp.h"
+#endif /* HAL_COMP_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+#include "stm32u0xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRS_MODULE_ENABLED
+#include "stm32u0xx_ll_crs.h"
+#endif /* HAL_CRS_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+#include "stm32u0xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+#include "stm32u0xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+#include "stm32u0xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+#include "stm32u0xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+#include "stm32u0xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+#include "stm32u0xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+#include "stm32u0xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_LCD_MODULE_ENABLED
+#include "stm32u0xx_hal_lcd.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_OPAMP_MODULE_ENABLED
+#include "stm32u0xx_hal_opamp.h"
+#endif /* HAL_OPAMP_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+#include "stm32u0xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+#include "stm32u0xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+#include "stm32u0xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+#include "stm32u0xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+#include "stm32u0xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_TSC_MODULE_ENABLED
+#include "stm32u0xx_ll_system.h"
+#include "stm32u0xx_hal_tsc.h"
+#endif /* HAL_TSC_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+#include "stm32u0xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+#include "stm32u0xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+#include "stm32u0xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+#include "stm32u0xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+#include "stm32u0xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_LCD_MODULE_ENABLED
+#include "stm32u0xx_hal_lcd.h"
+#endif /* HAL_LCD_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+#include "stm32u0xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  The assert_param macro is used for function's parameters check.
+  * @param  expr: If expr is false, it calls assert_failed function
+  *         which reports the name of the source file and the source
+  *         line number of the call that failed.
+  *         If expr is true, it returns no value.
+  * @retval None
+  */
+  #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+  void assert_failed(uint8_t *file, uint32_t line);
+#else
+  #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32U0xx_HAL_CONF_H */
+
diff --git a/tools/get_deps.py b/tools/get_deps.py
index 0828140c1..36ed98a62 100755
--- a/tools/get_deps.py
+++ b/tools/get_deps.py
@@ -124,6 +124,9 @@ deps_optional = {
     'hw/mcu/st/cmsis_device_n6': ['https://github.com/STMicroelectronics/cmsis-device-n6.git',
                                   '7bcdc944fbf7cf5928d3c1d14054ca13261d33ec',
                                   'stm32n6'],
+    'hw/mcu/st/cmsis-device-u0': ['https://github.com/STMicroelectronics/cmsis-device-u0.git',
+                                  'e3a627c6a5bc4eb2388e1885a95cc155e1672253',
+                                  'stm32u0'],
     'hw/mcu/st/cmsis_device_u5': ['https://github.com/STMicroelectronics/cmsis_device_u5.git',
                                   '6e67187dec98035893692ab2923914cb5f4e0117',
                                   'stm32u5'],
@@ -190,6 +193,9 @@ deps_optional = {
     'hw/mcu/st/stm32n6xx_hal_driver': ['https://github.com/STMicroelectronics/stm32n6xx-hal-driver.git',
                                        'bc6c41f8f67d61b47af26695d0bf67762a000666',
                                        'stm32n6'],
+    'hw/mcu/st/stm32u0xx_hal_driver': ['https://github.com/STMicroelectronics/stm32u0xx-hal-driver.git',
+                                       'cbfb5ac654256445237fd32b3587ac6a238d24f1',
+                                       'stm32u0'],
     'hw/mcu/st/stm32u5xx_hal_driver': ['https://github.com/STMicroelectronics/stm32u5xx_hal_driver.git',
                                        '2c5e2568fbdb1900a13ca3b2901fdd302cac3444',
                                        'stm32u5'],
@@ -240,7 +246,7 @@ deps_optional = {
                     'imxrt kinetis_k32l2 kinetis_kl lpc51 lpc54 lpc55 mcx mm32 msp432e4 nrf saml2x '
                     'lpc11 lpc13 lpc15 lpc17 lpc18 lpc40 lpc43 '
                     'stm32c0 stm32f0 stm32f1 stm32f2 stm32f3 stm32f4 stm32f7 stm32g0 stm32g4 stm32h5 '
-                    'stm32h7 stm32h7rs stm32l0 stm32l1 stm32l4 stm32l5 stm32n6 stm32u5 stm32wb stm32wba'
+                    'stm32h7 stm32h7rs stm32l0 stm32l1 stm32l4 stm32l5 stm32n6 stm32u0 stm32u5 stm32wb stm32wba'
                     'sam3x samd11 samd21 samd51 samd5x_e5x same5x same7x saml2x samg '
                     'tm4c '],
     'lib/CMSIS_6': ['https://github.com/ARM-software/CMSIS_6.git',