adding code to allow configure MIC2555 to pull down D+/D- (still need bit bangding I2C on PB_0 PB_1)

add back port reset after get 8 bytes of device descriptor

3 files changed, 64 insertions, 1 deletions

diff --git a/demos/bsp/boards/board.h b/demos/bsp/boards/board.h
index 23286f835..1fdc4a878 100644
--- a/demos/bsp/boards/board.h
+++ b/demos/bsp/boards/board.h
@@ -57,7 +57,7 @@
 
 #include <stdint.h>
 #include "common/compiler/compiler.h"
-#include "common/binary.h" // This file is too good to not use
+#include "common/binary.h"
 
 #define BOARD_AT86RF2XX             1
 #define BOARD_LPCXPRESSO1347        2
diff --git a/demos/bsp/boards/board_ea4357.c b/demos/bsp/boards/board_ea4357.c
index 51801bcb4..5cc26fc33 100644
--- a/demos/bsp/boards/board_ea4357.c
+++ b/demos/bsp/boards/board_ea4357.c
@@ -39,6 +39,8 @@
 
 #if BOARD == BOARD_EA4357
 
+#include "common/assertion.h" // TODO there is hal_debugger_ in assertion
+
 #define UART_PORT   LPC_USART0
 
 #if 0
@@ -48,6 +50,59 @@ static const struct {
 }leds[CFG_LED_NUMBER] = { {0, 8} };
 #endif
 
+// MIC2555 1YML = 0101111, 0YML = 0101101
+#define MIC255_ADDR BIN8(0101111)
+
+static uint8_t mic255_regs_read(uint8_t regs_addr)
+{
+  uint8_t value;
+
+  ASSERT( SUCCESS == I2C_MasterTransferData(
+      LPC_I2C0,
+      & (I2C_M_SETUP_Type)
+      {
+        .sl_addr7bit         = MIC255_ADDR,
+        .retransmissions_max = 3,
+
+        .tx_data             = &regs_addr,
+        .tx_length           = 1,
+
+        .rx_data             = &value,
+        .rx_length           = 1
+      },
+      I2C_TRANSFER_POLLING), 0xFF);
+
+  return value;
+}
+
+static bool mic255_regs_write(uint8_t regs_addr, uint8_t data)
+{
+  uint8_t xfer_data[2] = { regs_addr, data} ;
+
+  ASSERT( SUCCESS == I2C_MasterTransferData(
+      LPC_I2C0,
+      & (I2C_M_SETUP_Type)
+      {
+        .sl_addr7bit         = MIC255_ADDR,
+        .retransmissions_max = 3,
+
+        .tx_data             = xfer_data,
+        .tx_length           = 2,
+      },
+      I2C_TRANSFER_POLLING), false);
+
+  return true;
+}
+
+
+static uint16_t mic255_get_vendorid(void)
+{
+  uint8_t vendor_low  = mic255_regs_read(0);
+  uint8_t vendor_high = mic255_regs_read(1);
+
+  return (vendor_high << 8) | vendor_low;
+}
+
 void board_init(void)
 {
   SystemInit();
@@ -61,6 +116,13 @@ void board_init(void)
   // USB1 Power: EA4357 channel A U20 is enabled by SJ5 connected to pad 1-2, no more action required
   scu_pinmux(0x2, 5, MD_PLN | MD_EZI | MD_ZI, FUNC2);	// USB1_VBUS monitor presence, must be high for bus reset occur
 
+  // init I2C and set up MIC2555 to have 15k pull-down on USB1 D+ & D-
+//  I2C_Init(LPC_I2C0, 100000);
+//  I2C_Cmd(LPC_I2C0, ENABLE);
+//
+//  ASSERT_INT(0x058d, mic255_get_vendorid(), (void) 0); // verify vendor id
+//  ASSERT( mic255_regs_write(6, BIN8(1100)), (void) 0); // pull down D+/D- for host
+
 #if 0
   // Leds Init
 	for (uint8_t i=0; i<CFG_LED_NUMBER; i++)
diff --git a/demos/bsp/boards/board_ea4357.h b/demos/bsp/boards/board_ea4357.h
index ce4d482ea..b808ad9ed 100644
--- a/demos/bsp/boards/board_ea4357.h
+++ b/demos/bsp/boards/board_ea4357.h
@@ -60,6 +60,7 @@
 #include "lpc43xx_cgu.h"
 #include "lpc43xx_gpio.h"
 #include "lpc43xx_uart.h"
+#include "lpc43xx_i2c.h"
 
 #define CFG_LED_NUMBER  0
 #define CFG_LED_ON               (1)