- revert usb address

- more clean up

2 files changed, 7 insertions, 13 deletions

diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c
index 0380f36b9..9383923bd 100644
--- a/src/portable/renesas/rusb2/dcd_rusb2.c
+++ b/src/portable/renesas/rusb2/dcd_rusb2.c
@@ -51,7 +51,7 @@
   #endif
 
   // Application API for setting IRQ number
-  void tud_int_set_irqnum(uint8_t rhport, int32_t irqnum) {
+  void tud_rusb2_set_irqnum(uint8_t rhport, int32_t irqnum) {
     rusb2_controller[rhport].irqnum = irqnum;
   }
 
@@ -638,7 +638,7 @@ static void process_bus_reset(uint8_t rhport)
 static void process_set_address(uint8_t rhport)
 {
   rusb2_reg_t* rusb = RUSB2_REG(rhport);
-  const uint32_t addr = rusb->USBADDR & 0xFF;
+  const uint16_t addr = rusb->USBADDR_b.USBADDR;
   if (!addr) return;
 
   const tusb_control_request_t setup_packet = {
@@ -821,7 +821,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc)
 
   if ( rusb2_is_highspeed_rhport(rhport) ) {
     // FIXME shouldn't be after pipe selection and config, also the BUFNMB should be changed
-    // depending on the allocation scheme
+    //       depending on the allocation scheme
     rusb->PIPEBUF = 0x7C08;
   }
 
diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c
index fef8bdf19..c5ed8ae55 100644
--- a/src/portable/renesas/rusb2/hcd_rusb2.c
+++ b/src/portable/renesas/rusb2/hcd_rusb2.c
@@ -32,21 +32,15 @@
 #include "host/hcd.h"
 #include "rusb2_type.h"
 
-#if !defined(CFG_TUSB_RHPORT0_MODE) && !defined(CFG_TUSB_RHPORT1_MODE)
-// fallback
-#define CFG_TUSB_RHPORT0_MODE   OPT_MODE_HOST
-#define CFG_TUSB_RHPORT1_MODE   0
-#endif
-
 #if TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N)
   #include "rusb2_rx.h"
 
 #elif TU_CHECK_MCU(OPT_MCU_RAXXX)
   #include "rusb2_ra.h"
 
-  void osal_task_delay(uint32_t msec) {
-    R_BSP_SoftwareDelay(msec, BSP_DELAY_UNITS_MILLISECONDS);
-  }
+//  void osal_task_delay(uint32_t msec) {
+//    R_BSP_SoftwareDelay(msec, BSP_DELAY_UNITS_MILLISECONDS);
+//  }
 
 #else
   #error "Unsupported MCU"
@@ -785,7 +779,7 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) {
 void hcd_int_handler(uint8_t rhport)
 {
   rusb2_reg_t* rusb = RUSB2_REG(rhport);
-  static unsigned char attach_attempt = 0;
+  static unsigned char attach_attempt = 0; // TODO remove later
   unsigned is0 = rusb->INTSTS0;
   unsigned is1 = rusb->INTSTS1;