diff options
| -rw-r--r-- | examples/device/uac2_headset/skip.txt | 3 | ||||
| -rw-r--r-- | hw/bsp/stm32l0/boards/stm32l052dap52/STM32L052K8Ux_FLASH.ld | 169 | ||||
| -rw-r--r-- | hw/bsp/stm32l0/boards/stm32l052dap52/board.h | 109 | ||||
| -rw-r--r-- | hw/bsp/stm32l0/boards/stm32l052dap52/board.mk | 11 | ||||
| -rw-r--r-- | hw/bsp/stm32l0/family.c | 181 | ||||
| -rw-r--r-- | hw/bsp/stm32l0/family.mk | 40 | ||||
| -rw-r--r-- | hw/bsp/stm32l0/stm32l0xx_hal_conf.h | 338 |
7 files changed, 850 insertions, 1 deletions
diff --git a/examples/device/uac2_headset/skip.txt b/examples/device/uac2_headset/skip.txt index 9471822a4..70d8e8838 100644 --- a/examples/device/uac2_headset/skip.txt +++ b/examples/device/uac2_headset/skip.txt @@ -3,4 +3,5 @@ mcu:LPC13XX mcu:NUC121 mcu:SAMD11 mcu:SAME5X -mcu:SAMG
\ No newline at end of file +mcu:SAMG +board:stm32l052dap52 diff --git a/hw/bsp/stm32l0/boards/stm32l052dap52/STM32L052K8Ux_FLASH.ld b/hw/bsp/stm32l0/boards/stm32l052dap52/STM32L052K8Ux_FLASH.ld new file mode 100644 index 000000000..1bc16cc7b --- /dev/null +++ b/hw/bsp/stm32l0/boards/stm32l052dap52/STM32L052K8Ux_FLASH.ld @@ -0,0 +1,169 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32L052K8Ux Device with +** 64KByte FLASH, 8KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20002000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 64K +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 8K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} + + diff --git a/hw/bsp/stm32l0/boards/stm32l052dap52/board.h b/hw/bsp/stm32l0/boards/stm32l052dap52/board.h new file mode 100644 index 000000000..8ad3e43c8 --- /dev/null +++ b/hw/bsp/stm32l0/boards/stm32l052dap52/board.h @@ -0,0 +1,109 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +// LED +#define LED_PORT GPIOB +#define LED_PIN GPIO_PIN_4 +#define LED_STATE_ON 1 + +// Button +#define BUTTON_PORT GPIOA +#define BUTTON_PIN GPIO_PIN_6 +#define BUTTON_STATE_ACTIVE 0 + +// UART +#define UART_DEV USART2 +#define UART_CLK_EN __HAL_RCC_USART2_CLK_ENABLE +#define UART_GPIO_PORT GPIOA +#define UART_GPIO_AF GPIO_AF4_USART2 +#define UART_TX_PIN GPIO_PIN_2 +#define UART_RX_PIN GPIO_PIN_3 + +//--------------------------------------------------------------------+ +// RCC Clock +//--------------------------------------------------------------------+ +static inline void board_stm32l0_clock_init(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_PeriphCLKInitTypeDef PeriphClkInitStruct; + static RCC_CRSInitTypeDef RCC_CRSInitStruct; + + /* Enable HSI Oscillator to be used as System clock source + Enable HSI48 Oscillator to be used as USB clock source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSI48; + RCC_OscInitStruct.HSIState = RCC_HSI_ON; + RCC_OscInitStruct.HSI48State = RCC_HSI48_ON; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Select HSI48 as USB clock source */ + PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB; + PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_HSI48; + HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct); + + /* Select HSI as system clock source and configure the HCLK, PCLK1 and PCLK2 + clock dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0); + + /*Configure the clock recovery system (CRS)**********************************/ + + /*Enable CRS Clock*/ + __HAL_RCC_CRS_CLK_ENABLE(); + + /* Default Synchro Signal division factor (not divided) */ + RCC_CRSInitStruct.Prescaler = RCC_CRS_SYNC_DIV1; + /* Set the SYNCSRC[1:0] bits according to CRS_Source value */ + RCC_CRSInitStruct.Source = RCC_CRS_SYNC_SOURCE_USB; + /* HSI48 is synchronized with USB SOF at 1KHz rate */ + RCC_CRSInitStruct.ReloadValue = __HAL_RCC_CRS_RELOADVALUE_CALCULATE(48000000, 1000); + RCC_CRSInitStruct.ErrorLimitValue = RCC_CRS_ERRORLIMIT_DEFAULT; + /* Set the TRIM[5:0] to the default value*/ + RCC_CRSInitStruct.HSI48CalibrationValue = 0x20; + /* Start automatic synchronization */ + HAL_RCCEx_CRSConfig (&RCC_CRSInitStruct); +} + +static inline void board_vbus_sense_init(void) +{ +} + +#ifdef __cplusplus + } +#endif + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/stm32l0/boards/stm32l052dap52/board.mk b/hw/bsp/stm32l0/boards/stm32l052dap52/board.mk new file mode 100644 index 000000000..84662344d --- /dev/null +++ b/hw/bsp/stm32l0/boards/stm32l052dap52/board.mk @@ -0,0 +1,11 @@ +CFLAGS += -DSTM32L052xx -DCFG_EXAMPLE_VIDEO_READONLY + +LD_FILE = $(BOARD_PATH)/STM32L052K8Ux_FLASH.ld + +SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32l052xx.s + +# For flash-jlink target +JLINK_DEVICE = stm32l052k8 + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32l0/family.c b/hw/bsp/stm32l0/family.c new file mode 100644 index 000000000..80a7c7435 --- /dev/null +++ b/hw/bsp/stm32l0/family.c @@ -0,0 +1,181 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "stm32l0xx_hal.h" +#include "bsp/board.h" +#include "board.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB_IRQHandler(void) +{ + tud_int_handler(0); +} + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ +UART_HandleTypeDef UartHandle; + +void board_init(void) +{ + board_stm32l0_clock_init(); + + // Enable All GPIOs clocks + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOD_CLK_ENABLE(); + + // Enable UART Clock + UART_CLK_EN(); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + +#elif CFG_TUSB_OS == OPT_OS_FREERTOS + // Explicitly disable systick to prevent its ISR runs before scheduler start + SysTick->CTRL &= ~1U; + + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(USB_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); +#endif + + // LED + GPIO_InitTypeDef GPIO_InitStruct; + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Button + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_PULLDOWN; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // Uart + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + UartHandle.Instance = UART_DEV; + UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + UartHandle.Init.WordLength = UART_WORDLENGTH_8B; + UartHandle.Init.StopBits = UART_STOPBITS_1; + UartHandle.Init.Parity = UART_PARITY_NONE; + UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + UartHandle.Init.Mode = UART_MODE_TX_RX; + UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + HAL_UART_Init(&UartHandle); + + // USB Pins + // Configure USB DM and DP pins. This is optional, and maintained only for user guidance. + GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + // USB Clock enable + __HAL_RCC_USB_CLK_ENABLE(); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); +} + +uint32_t board_button_read(void) +{ + return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + HAL_UART_Transmit(&UartHandle, (uint8_t*)(uintptr_t) buf, len, 0xffff); + return len; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +#ifdef USE_FULL_ASSERT +/** + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(uint8_t* file, uint32_t line) +{ + (void) file; (void) line; + /* USER CODE BEGIN 6 */ + /* User can add his own implementation to report the file name and line number, + tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + /* USER CODE END 6 */ +} +#endif /* USE_FULL_ASSERT */ + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32l0/family.mk b/hw/bsp/stm32l0/family.mk new file mode 100644 index 000000000..622fa61e0 --- /dev/null +++ b/hw/bsp/stm32l0/family.mk @@ -0,0 +1,40 @@ +ST_FAMILY = l0 +DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver + +ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY) +ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver + +include $(TOP)/$(BOARD_PATH)/board.mk + +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m0plus \ + -mfloat-abi=soft \ + -nostdlib -nostartfiles \ + -DCFG_EXAMPLE_MSC_READONLY \ + -DCFG_EXAMPLE_VIDEO_READONLY \ + -DCFG_TUSB_MCU=OPT_MCU_STM32L0 + +# suppress warning caused by vendor mcu driver +CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls -Wno-error=cast-align -Wno-error=maybe-uninitialized + +SRC_C += \ + src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c \ + $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c + +INC += \ + $(TOP)/$(BOARD_PATH) \ + $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM0 diff --git a/hw/bsp/stm32l0/stm32l0xx_hal_conf.h b/hw/bsp/stm32l0/stm32l0xx_hal_conf.h new file mode 100644 index 000000000..cc20ea8e0 --- /dev/null +++ b/hw/bsp/stm32l0/stm32l0xx_hal_conf.h @@ -0,0 +1,338 @@ +/** + ****************************************************************************** + * @file stm32l0xx_hal_conf.h + * @author MCD Application Team + * @brief HAL configuration template file. + * This file should be copied to the application folder and renamed + * to stm32l0xx_hal_conf.h. + ****************************************************************************** + * @attention + * + * <h2><center>© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.</center></h2> + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32L0xx_HAL_CONF_H +#define __STM32L0xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +/*#define HAL_ADC_MODULE_ENABLED */ +/*#define HAL_COMP_MODULE_ENABLED */ +/*#define HAL_CRC_MODULE_ENABLED */ +/*#define HAL_CRYP_MODULE_ENABLED */ +/*#define HAL_DAC_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/*#define HAL_FIREWALL_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +/*#define HAL_I2C_MODULE_ENABLED */ +/*#define HAL_I2S_MODULE_ENABLED */ +/*#define HAL_IWDG_MODULE_ENABLED */ +/*#define HAL_LCD_MODULE_ENABLED */ +/*#define HAL_LPTIM_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +/*#define HAL_RNG_MODULE_ENABLED */ +/*#define HAL_RTC_MODULE_ENABLED */ +/*#define HAL_SPI_MODULE_ENABLED */ +/*#define HAL_TIM_MODULE_ENABLED */ +/*#define HAL_TSC_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED +/*#define HAL_USART_MODULE_ENABLED */ +/*#define HAL_IRDA_MODULE_ENABLED */ +/*#define HAL_SMARTCARD_MODULE_ENABLED */ +/*#define HAL_SMBUS_MODULE_ENABLED */ +/*#define HAL_WWDG_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +#define HAL_PCD_MODULE_ENABLED + +/* ########################## Oscillator Values adaptation ####################*/ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal Multiple Speed oscillator (MSI) default value. + * This value is the default MSI range value after Reset. + */ +#if !defined (MSI_VALUE) + #define MSI_VALUE ((uint32_t)2097152U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* MSI_VALUE */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief Internal High Speed oscillator for USB (HSI48) value. + */ +#if !defined (HSI48_VALUE) +#define HSI48_VALUE ((uint32_t)48000000U) /*!< Value of the Internal High Speed oscillator for USB in Hz. + The real value may vary depending on the variations + in voltage and temperature. */ +#endif /* HSI48_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)37000U) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature.*/ +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External oscillator in Hz*/ +#endif /* LSE_VALUE */ + +/** + * @brief Time out for LSE start up value in ms. + */ +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY (((uint32_t)1U<<__NVIC_PRIO_BITS) - 1U) /*!< tick interrupt priority */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 1U +#define PREREAD_ENABLE 0U +#define BUFFER_CACHE_DISABLE 0U + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1U */ + + +/* ################## Register callback feature configuration ############### */ +/** + * @brief Set below the peripheral configuration to "1U" to add the support + * of HAL callback registration/deregistration feature for the HAL + * driver(s). This allows user application to provide specific callback + * functions thanks to HAL_PPP_RegisterCallback() rather than overwriting + * the default weak callback functions (see each stm32l0xx_hal_ppp.h file + * for possible callback identifiers defined in HAL_PPP_CallbackIDTypeDef + * for each PPP peripheral). + */ +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U +#define USE_HAL_COMP_REGISTER_CALLBACKS 0U +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U +#define USE_HAL_TSC_REGISTER_CALLBACKS 0U +#define USE_HAL_UART_REGISTER_CALLBACKS 0U +#define USE_HAL_USART_REGISTER_CALLBACKS 0U +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver + * Activated: CRC code is present inside driver + * Deactivated: CRC code cleaned from driver + */ + +#define USE_SPI_CRC 1U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32l0xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32l0xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32l0xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32l0xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32l0xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_COMP_MODULE_ENABLED + #include "stm32l0xx_hal_comp.h" +#endif /* HAL_COMP_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32l0xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32l0xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32l0xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FIREWALL_MODULE_ENABLED + #include "stm32l0xx_hal_firewall.h" +#endif /* HAL_FIREWALL_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32l0xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32l0xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32l0xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32l0xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LCD_MODULE_ENABLED + #include "stm32l0xx_hal_lcd.h" +#endif /* HAL_LCD_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +#include "stm32l0xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32l0xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32l0xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32l0xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32l0xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32l0xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_TSC_MODULE_ENABLED + #include "stm32l0xx_hal_tsc.h" +#endif /* HAL_TSC_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32l0xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32l0xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32l0xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32l0xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + #include "stm32l0xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32l0xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32l0xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32L0xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ + |