diff options
Diffstat (limited to 'changelog.md')
| -rw-r--r-- | changelog.md | 124 |
1 files changed, 98 insertions, 26 deletions
diff --git a/changelog.md b/changelog.md index a71a986f2..6b17e1666 100644 --- a/changelog.md +++ b/changelog.md @@ -1,46 +1,118 @@ # TinyUSB Changelog -## Master branch (WIP) +## 0.7.0 - 2020.11.08 -### Breaking +### Device Controller Driver -- TinyUSB does not directly implement USB IRQ Handler function anymore. Application must implement IRQ Handler and invoke `tud_int_handler(rhport)`. This is due to: - - IRQ Handler name can be different across system depending on the startup - - Some OS need to execute enterISR()/exitISR() to work properly, also tracing tool may need to insert trace ISR enter/exit to record usb event - - Give application full control of IRQ handler, can be useful e.g signaling there is new usb event without constant polling +- Added new support for Espressif ESP32-S2 +- Added new support for Dialog DA1469x +- Enhance STM32 Synopsys + - Support bus events disconnection/suspend/resume/wakeup + - Improve transfer performance with optimizing xfer and fifo size + - Support Highspeed port (OTG_HS) with both internal and external PHY + - Support multiple usb ports with rhport=1 is highspeed on selected MCUs e.g H743, F23. It is possible to have OTG_HS to run on Fullspeed PHY (e.g lacking external PHY) + - Add ISO transfer, fix odd/even frame + - Fix FIFO flush during stall + - Implement dcd_edpt_close() API + - Support F105, F107 +- Enhance STM32 fsdev + - Improve dcd fifo allocation + - Fix ISTR race condition + - Support remap USB IRQ on supported MCUs + - Implement dcd_edpt_close() API +- Enhance NUC 505: enhance set configure behavior +- Enhance SAMD + - Fix race condition with setup packet + - Add SAMD11 option `OPT_MCU_SAMD11` + - Add SAME5x option `OPT_MCU_SAME5X` +- Fix SAMG control data toggle and stall race condition +- Enhance nRF + - Fix hanged when tud_task() is called within critical section (disabled interrupt) + - Fix disconnect bus event not submitted + - Implement ISO transfer and dcd_edpt_close() -### MCU +### USB Device -- Added support for Espressif ESP32-S2 and saola-1 board -- All default IRQ Handler is renamed to `dcd_int_handler()` -- STM32 Synopsys - - Bus events disconnection/suspend/resume are supported -- Added `dcd_connect()` and `dcd_disconnect()` to enable/disable internal pullup on D+/D- on supported MCUs. -- Added `dcd_edpt_close()` for STM32 FSDev +**USBD** -### Device Stack - -- tud_cdc_n_write_flush() return number of bytes forced to transfer instead of bool +- Add new class driver for **Bluetooth HCI** class driver with example can be found in [mynewt-tinyusb-example](https://github.com/hathach/mynewt-tinyusb-example) since it needs mynewt OS to run with. +- Fix USBD endpoint usage racing condition with `usbd_edpt_claim()/usbd_edpt_release()` +- Added `tud_task_event_ready()` and `osal_queue_empty()`. This API is needed to check before enter low power mode with WFI/WFE +- Rename USB IRQ Handler to `dcd_int_handler()`. Application must define IRQ handler in which it calls this API. +- Add `dcd_connect()` and `dcd_disconnect()` to enable/disable internal pullup on D+/D- on supported MCUs. +- Add `usbd_edpt_open()` +- Remove `dcd_set_config()` +- Add *OPT_OS_CUMSTOM* as hook for application to overwrite and/or add their own OS implementation +- Support SET_INTERFACE, GET_INTERFACE request +- Add Logging for debug with optional uart/rtt/swo printf retarget or `CFG_TUSB_DEBUG_PRINTF` hook +- Add IAR compiler support - Support multiple configuration descriptors. `TUD_CONFIG_DESCRIPTOR()` template has extra config_num as 1st argument -- Improve class driver management - - Driver detection is done by open() API +- Improve USB Highspeed support with actual link speed detection with `dcd_event_bus_reset()` +- Enhance class driver management + - `usbd_driver_open()` add max length argument, and return length of interface (0 for not supported). Return value is used for finding appropriate driver + - Add application implemented class driver via `usbd_app_driver_get_cb()` - IAD is handled to assign driver id -- Improve Alternate Interface request with `SET_INTERFACE()` (not fully supported yet). -- Fixed CDC ZLP response #260 -- Remove ACM-EEM due to lack of support from host +- Added `tud_descriptor_device_qualifier_cb()` callback +- Optimize `tu_fifo` bulk write/read transfer +- Forward non-std control request to class driver +- Let application handle Microsoft OS 1.0 Descriptors (the 0xEE index string) +- Fix OSAL FreeRTOS yield from ISR + +**Class Drivers** + +- USBNET: remove ACM-EEM due to lack of support from host +- USBTMC: fix descriptors when INT EP is disabled +- CDC: + - Send zero length packet for end of data when needed + - Add `tud_cdc_tx_complete_cb()` callback + - Change tud_cdc_n_write_flush() return number of bytes forced to transfer, and flush when writing enough data to fifo +- MIDI: + - Add packet interface + - Add multiple jack descriptors + - Fix MIDI driver for sysex +- DFU Runtime: fix response to SET_INTERFACE and DFU_GETSTATUS request +- Rename some configure macro to make it clear that those are used directly for endpoint transfer + - CFG_TUD_HID_BUFSIZE to `CFG_TUD_HID_EP_BUFSIZE + - CFG_TUD_CDC_EPSIZE to CFG_TUD_CDC_EP_BUFSIZE + - CFG_TUD_MSC_BUFSIZE to CFG_TUD_MSC_EP_BUFSIZE + - CFG_TUD_MIDI_EPSIZE to CFG_TUD_MIDI_EP_BUFSIZE +- HID: + - Fix gamepad template descriptor + - Add multiple HID interface API + - Add extra comma to HID_REPORT_ID + +### USB Host + +- Rework USB host stack (still work in progress) + - Fix compile error with pipehandle + - Rework usbh control and enumeration as non-blocking +- Improve Hub, MSC, HID host driver + +### Examples + +- Add new hid_composite_freertos +- Add new dynamic_configuration to demonstrate how to switch configuration descriptors +- Add new hid_multiple_interface +- Enhance `net_lwip_webserver` example + - Add multiple configuration: RNDIS for Windows, CDC-ECM for macOS (Linux will work with both) + - Update lwip to STABLE-2_1_2_RELEASE for net_lwip_webserver +- Added new Audio example: audio_test uac2_headsest -### Others +### New Boards -- Added OPT_OS_CUMSTOM as hook for application to overwrite and/or add their own OS implementation -- Enhanced `net_lwip_webserver` example with multiple configuration: RNDIS for Windows, CDC-ECM for macOS (Linux will work with both) +- Espressif ESP32-S2: saola_1, kaluga_1 +- STM32: F746 Nucleo, H743 Eval, H743 Nucleo, F723 discovery, stlink v3 mini, STM32L4r5 Nucleo +- Dialog DA1469x dk pro and dk usb +- Microchip: Great Scoot Gadgets' LUNA, samd11_xplained, D5035-01, atsamd21 xplained pro +- nRF: ItsyBitsy nRF52840 -## 0.6.0 - 2019.03.30 +## 0.6.0 - 2020.03.30 Added **CONTRIBUTORS.md** to give proper credit for contributors to the stack. Special thanks to [Nathan Conrad](https://github.com/pigrew), [Peter Lawrence](https://github.com/majbthrd) and [William D. Jones](https://github.com/cr1901) and others for spending their precious time to add lots of features and ports for this release. ### Added -**MCU** +**MCUs** - Added support for Microchip SAMG55 - Added support for Nordic nRF52833 |