diff options
Diffstat (limited to 'docs/info')
| -rw-r--r-- | docs/info/changelog.rst | 48 | ||||
| -rw-r--r-- | docs/info/code_of_conduct.rst | 1 | ||||
| -rw-r--r-- | docs/info/index.rst | 1 |
3 files changed, 50 insertions, 0 deletions
diff --git a/docs/info/changelog.rst b/docs/info/changelog.rst index b4423f81e..d6bf846ed 100644 --- a/docs/info/changelog.rst +++ b/docs/info/changelog.rst @@ -20,6 +20,7 @@ API Changes ----------- - Core APIs + - Add weak callbacks with new syntax for better compiler compatibility - Add ``tusb_deinit()`` to cleanup stack - Add time functions: ``tusb_time_millis_api()`` and ``tusb_time_delay_ms_api()`` @@ -27,6 +28,7 @@ API Changes - Introduce ``xfer_isr()`` callback for ISO transfer optimization in device classes - Device APIs + - CDC: Add notification support ``tud_cdc_configure()``, ``tud_cdc_n_notify_uart_state()``, ``tud_cdc_n_notify_conn_speed_change()``, ``tud_cdc_notify_complete_cb()`` - MSC: Add ``tud_msc_inquiry2_cb()`` with bufsize parameter, update ``tud_msc_async_io_done()`` @@ -36,6 +38,7 @@ API Changes ``tud_mtp_response_send()``, ``tud_mtp_event_send()`` - Host APIs + - Core: Add ``tuh_edpt_close()``, ``tuh_address_set()``, ``tuh_descriptor_get_device_local()``, ``tuh_descriptor_get_string_langid()``, ``tuh_connected()``, ``tuh_bus_info_get()`` - Add enumeration callbacks: ``tuh_enum_descriptor_device_cb()``, @@ -50,6 +53,7 @@ Controller Driver (DCD & HCD) ----------------------------- - DWC2 + - Support DWC2 v4.30a with improved reset procedure - Fix core reset: wait for AHB idle before reset - Add STM32 DWC2 data cache support with proper alignment @@ -64,6 +68,7 @@ Controller Driver (DCD & HCD) - Refactor bitfields for better code generation - FSDEV (STM32) + - Fix AT32 compile issues after single-buffered endpoint changes - Add configurable single-buffered isochronous endpoints - Fix STM32H7 recurrent suspend ISR @@ -72,35 +77,42 @@ Controller Driver (DCD & HCD) - Improve PMA size handling for STM32U0 - EHCI + - Fix removed QHD getting reused - Fix NXP USBPHY disconnection detection - Chipidea/NXP + - Fix race condition with spinlock - Improve iMXRT support: fix build, disable BOARD_ConfigMPU, fix attach debouncing on port1 highspeed - Fix iMXRT1064 and add to HIL test pool - MAX3421E + - Use spinlock for thread safety instead of atomic flag - Implement ``hcd_edpt_close()`` - RP2040 + - Fix audio ISO transfer: reset state before notifying stack - Fix CMake RTOS cache variable - Abort transfer if active in ``iso_activate()`` - SAMD + - Add host controller driver support Device Stack ------------ - USBD Core + - Introduce ``xfer_isr()`` callback for interrupt-time transfer handling - Add ``usbd_edpt_xfer_fifo()`` stub - Revert endpoint busy/claim status if ``xfer_isr()`` defers to ``xfer_cb()`` - Audio + - Major simplification of UAC driver and alt settings management - Move ISO transfers into ``xfer_isr()`` for better performance - Remove FIFO mutex (single producer/consumer optimization) @@ -109,25 +121,30 @@ Device Stack - Update buffer macros with cache line size alignment - CDC + - Add notification support: ``CFG_TUD_CDC_NOTIFY``, ``tud_cdc_n_notify_conn_speed_change()``, ``tud_cdc_notify_complete_cb()`` - Reduce default bInterval from 16ms to 1ms for better responsiveness - Rename ``tud_cdc_configure_fifo()`` to ``tud_cdc_configure()`` and add ``tx_overwritable_if_not_connected`` option - Fix web serial robustness with major overhaul and logic cleanup - HID + - Add Usage Page and Table for Power Devices (0x84 - 0x85) - Fix HID descriptor parser variable size and 4-byte item handling - Add consumer page configurations - MIDI + - Fix MIDI interface descriptor handling after audio streaming interface - Skip RX data with all zeroes - MSC + - Add async I/O support for MSC using ``tud_msc_async_io_done()`` - Add ``tud_msc_inquiry2_cb()`` with bufsize for full inquiry response - MTP + - Add new Media Transfer Protocol (MTP) device class driver - Support MTP operations: GetDeviceInfo, SendObjectInfo, SendObject - Add MTP event support with ``tud_mtp_event_send()`` @@ -135,13 +152,16 @@ Device Stack - Add hardware-in-the-loop testing support - NCM + - Add USB NCM link state control support - Fix DHCP offer/ACK destination - USBTMC + - Add vendor-specific message support - Vendor + - Fix vendor device reset and open issues - Fix descriptor parsing for ``CFG_TUD_VENDOR > 1`` - Fix vendor FIFO argument calculation @@ -150,6 +170,7 @@ Host Stack ---------- - USBH Core + - Major enumeration improvements: - Fix enumeration racing conditions - Add proper attach debouncing with hub/rootport handling (200ms delay) @@ -173,6 +194,7 @@ Host Stack - Force removed devices in same bus info before setting address - CDC Serial Host + - Major refactor to generalize CDC serial drivers (FTDI, CP210x, CH34x, PL2303, ACM) - Add explicit ``sync()`` API with ``TU_API_SYNC()`` returning ``tusb_xfer_result_t`` - Rename ``tuh_cdc_get_local_line_coding()`` to ``tuh_cdc_get_line_coding_local()`` @@ -180,6 +202,7 @@ Host Stack - Implement ``tuh_cdc_get/set_dtr/rts()`` as inline functions - MIDI Host + - Major API changes: - Rename ``tuh_midi_stream_flush()`` to ``tuh_midi_write_flush()`` - Add ``tuh_midi_packet_read_n()`` and ``tuh_midi_packet_write_n()`` @@ -189,9 +212,11 @@ Host Stack - Add ``tuh_midi_descriptor_cb()`` and ``tuh_midi_itf_get_info()`` - MSC Host + - Continue async I/O improvements - HID Host + - Fix version string to actually show version 0.18.0 @@ -226,6 +251,7 @@ Controller Driver (DCD & HCD) ----------------------------- - DWC2 + - Add DMA support for both device and host controller - Add host driver support including: full/high speed, control/bulk/interrupt (CBI) transfer, split CBI i.e FS/LS attached via highspeed hub, hub support @@ -695,6 +721,7 @@ Controller Driver (DCD & HCD) ----------------------------- - [DWC2] Generalize synopsys dwc2 with synopsys/dwc2 which support both FS and HS phy (UTMI and ULPI) for various MCUs. + - Broadcom 28/27xx on raspberrypi SBC - Silicon Labs EFM32 - Espressif ESP32 Sx @@ -916,6 +943,7 @@ HID - Add more hid keys constant from 0x6B to 0xA4 - [Breaking] rename API + - ``HID_PROTOCOL_NONE/KEYBOARD/MOUSE`` to ``HID_ITF_PROTOCOL_NONE/KEYBOARD/MOUSE`` - ``tud_hid_boot_mode()`` to ``tud_hid_get_protocol()`` - ``tud_hid_boot_mode_cb()`` to ``tud_hid_set_protocol_cb()`` @@ -925,6 +953,7 @@ MIDI - Fix MIDI buffer overflow issue - [Breaking] rename API + - Rename ``tud_midi_read()`` to ``tud_midi_stream_read()`` - Rename ``tud_midi_write()`` to ``tud_midi_stream_write()`` - Rename ``tud_midi_receive()`` to ``tud_midi_packet_read()`` @@ -1075,15 +1104,19 @@ Device Controller Driver - Use ``dcd_event_bus_reset()`` with link speed to replace bus_signal - ESP32-S2: + - Add bus suspend and wakeup support - SAMD21: + - Fix (walkaround) samd21 setup_packet overflow by USB DMA - STM32 Synopsys: + - Rework USB FIFO allocation scheme and allow RX FIFO size reduction - Sony CXD56 + - Update Update Spresense SDK to 2.0.2 - Fix dcd issues with setup packets - Correct EP number for cdc_msc example @@ -1100,19 +1133,24 @@ USB Device **Class Driver** - CDC + - Allow to transmit data, even if the host does not support control line states i.e set DTR - HID + - change default ``CFG_TUD_HID_EP_BUFSIZE`` from 16 to 64 - MIDI + - Fix midi sysex sending bug - MSC + - Invoke only scsi complete callback after status transaction is complete. - Fix ``scsi_mode_sense6_t`` padding, which cause IAR compiler internal error. - USBTMC + - Change interrupt endpoint example size to 8 instead of 2 for better compatibility with mcu **Example** @@ -1154,6 +1192,7 @@ Device Controller Driver - Enhance STM32 Synopsys - Support bus events disconnection/suspend/resume/wakeup + - Improve transfer performance with optimizing xfer and fifo size - Support Highspeed port (OTG_HS) with both internal and external PHY - Support multiple usb ports with rhport=1 is highspeed on selected MCUs e.g H743, F23. It is possible to have OTG_HS to run on Fullspeed PHY (e.g lacking external PHY) @@ -1163,6 +1202,7 @@ Device Controller Driver - Support F105, F107 - Enhance STM32 fsdev + - Improve dcd fifo allocation - Fix ISTR race condition - Support remap USB IRQ on supported MCUs @@ -1171,6 +1211,7 @@ Device Controller Driver - Enhance NUC 505: enhance set configure behavior - Enhance SAMD + - Fix race condition with setup packet - Add SAMD11 option ``OPT_MCU_SAMD11`` - Add SAME5x option ``OPT_MCU_SAME5X`` @@ -1178,6 +1219,7 @@ Device Controller Driver - Fix SAMG control data toggle and stall race condition - Enhance nRF + - Fix hanged when ``tud_task()`` is called within critical section (disabled interrupt) - Fix disconnect bus event not submitted - Implement ISO transfer and ``dcd_edpt_close()`` @@ -1203,6 +1245,7 @@ USB Device - Improve USB Highspeed support with actual link speed detection with ``dcd_event_bus_reset()`` - Enhance class driver management + - ``usbd_driver_open()`` add max length argument, and return length of interface (0 for not supported). Return value is used for finding appropriate driver - Add application implemented class driver via ``usbd_app_driver_get_cb()`` - IAD is handled to assign driver id @@ -1219,11 +1262,13 @@ USB Device - USBTMC: fix descriptors when INT EP is disabled - CDC: + - Send zero length packet for end of data when needed - Add ``tud_cdc_tx_complete_cb()`` callback - Change ``tud_cdc_n_write_flush()`` return number of bytes forced to transfer, and flush when writing enough data to fifo - MIDI: + - Add packet interface - Add multiple jack descriptors - Fix MIDI driver for sysex @@ -1231,12 +1276,14 @@ USB Device - DFU Runtime: fix response to SET_INTERFACE and DFU_GETSTATUS request - Rename some configure macro to make it clear that those are used directly for endpoint transfer + - ``CFG_TUD_HID_BUFSIZE`` to ``CFG_TUD_HID_EP_BUFSIZE`` - ``CFG_TUD_CDC_EPSIZE`` to ``CFG_TUD_CDC_EP_BUFSIZE`` - ``CFG_TUD_MSC_BUFSIZE`` to ``CFG_TUD_MSC_EP_BUFSIZE`` - ``CFG_TUD_MIDI_EPSIZE`` to ``CFG_TUD_MIDI_EP_BUFSIZE`` - HID: + - Fix gamepad template descriptor - Add multiple HID interface API - Add extra comma to HID_REPORT_ID @@ -1258,6 +1305,7 @@ Examples - Add new ``hid_multiple_interface`` - Enhance ``net_lwip_webserver`` example + - Add multiple configuration: RNDIS for Windows, CDC-ECM for macOS (Linux will work with both) - Update lwip to STABLE-2_1_2_RELEASE for ``net_lwip_webserver`` diff --git a/docs/info/code_of_conduct.rst b/docs/info/code_of_conduct.rst new file mode 100644 index 000000000..2d70708d4 --- /dev/null +++ b/docs/info/code_of_conduct.rst @@ -0,0 +1 @@ +.. include:: ../../CODE_OF_CONDUCT.rst diff --git a/docs/info/index.rst b/docs/info/index.rst index a636f37dc..b6d30b432 100644 --- a/docs/info/index.rst +++ b/docs/info/index.rst @@ -10,3 +10,4 @@ Index changelog contributors + code_of_conduct |