diff options
Diffstat (limited to 'examples/device/dynamic_configuration')
4 files changed, 35 insertions, 32 deletions
diff --git a/examples/device/dynamic_configuration/src/main.c b/examples/device/dynamic_configuration/src/main.c index 4c10f55b0..33a603343 100644 --- a/examples/device/dynamic_configuration/src/main.c +++ b/examples/device/dynamic_configuration/src/main.c @@ -55,7 +55,9 @@ void midi_task(void); int main(void) { board_init(); - tusb_init(); + + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { @@ -179,7 +181,7 @@ void midi_task(void) start_ms += 286; // Previous positions in the note sequence. - int previous = note_pos - 1; + int previous = (int) (note_pos - 1); // If we currently are at position 0, set the // previous position to the last note in the sequence. diff --git a/examples/device/dynamic_configuration/src/msc_disk.c b/examples/device/dynamic_configuration/src/msc_disk.c index a895f4738..e8cb03fdd 100644 --- a/examples/device/dynamic_configuration/src/msc_disk.c +++ b/examples/device/dynamic_configuration/src/msc_disk.c @@ -184,7 +184,7 @@ int32_t tud_msc_read10_cb(uint8_t lun, uint32_t lba, uint32_t offset, void* buff uint8_t const* addr = msc_disk[lba] + offset; memcpy(buffer, addr, bufsize); - return bufsize; + return (int32_t) bufsize; } // Callback invoked when received WRITE10 command. @@ -203,7 +203,7 @@ int32_t tud_msc_write10_cb(uint8_t lun, uint32_t lba, uint32_t offset, uint8_t* (void) lba; (void) offset; (void) buffer; #endif - return bufsize; + return (int32_t) bufsize; } // Callback invoked when received an SCSI command not in built-in list below @@ -237,7 +237,7 @@ int32_t tud_msc_scsi_cb (uint8_t lun, uint8_t const scsi_cmd[16], void* buffer, { if(in_xfer) { - memcpy(buffer, response, resplen); + memcpy(buffer, response, (size_t) resplen); }else { // SCSI output diff --git a/examples/device/dynamic_configuration/src/tusb_config.h b/examples/device/dynamic_configuration/src/tusb_config.h index ddc295dcc..b9b3878cc 100644 --- a/examples/device/dynamic_configuration/src/tusb_config.h +++ b/examples/device/dynamic_configuration/src/tusb_config.h @@ -30,41 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -78,7 +79,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/dynamic_configuration/src/usb_descriptors.c b/examples/device/dynamic_configuration/src/usb_descriptors.c index 3352972a5..457f774d0 100644 --- a/examples/device/dynamic_configuration/src/usb_descriptors.c +++ b/examples/device/dynamic_configuration/src/usb_descriptors.c @@ -163,7 +163,7 @@ uint8_t const desc_configuration_0[] = TUD_CONFIG_DESCRIPTOR(1, ITF_0_NUM_TOTAL, 0, CONFIG_0_TOTAL_LEN, 0x00, 100), // Interface number, string index, EP notification address and size, EP data address (out, in) and size. - TUD_CDC_DESCRIPTOR(ITF_0_NUM_CDC, 0, EPNUM_0_CDC_NOTIF, 8, EPNUM_0_CDC_OUT, EPNUM_0_CDC_IN, 64), + TUD_CDC_DESCRIPTOR(ITF_0_NUM_CDC, 0, EPNUM_0_CDC_NOTIF, 8, EPNUM_0_CDC_OUT, EPNUM_0_CDC_IN, TUD_OPT_HIGH_SPEED ? 512 : 64), // Interface number, string index, EP Out & EP In address, EP size TUD_MIDI_DESCRIPTOR(ITF_0_NUM_MIDI, 0, EPNUM_0_MIDI_OUT, EPNUM_0_MIDI_IN, TUD_OPT_HIGH_SPEED ? 512 : 64), @@ -226,7 +226,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -237,7 +237,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } |