1 files changed, 2 insertions, 62 deletions
diff --git a/examples/readme.md b/examples/readme.md
index 407638da7..228029e99 100644
--- a/examples/readme.md
+++ b/examples/readme.md
@@ -1,63 +1,3 @@
-# Build Demos
+# Examples
 
-<!-- START doctoc generated TOC please keep comment here to allow auto update -->
-<!-- DON'T EDIT THIS SECTION, INSTEAD RE-RUN doctoc TO UPDATE -->
-**Table of Contents**
-
-- [LPCXpresso](#lpcxpresso)
-- [Keil](#keil)
-- [IAR](#iar)
-- [Configure demo](#configure-demo)
-
-<!-- END doctoc generated TOC please keep comment here to allow auto update -->
-
-## LPCXpresso
-
-LPCXpresso is an eclipse-based IDE, so you will need to create an workspace first then import project files (.cproject & .project) into it. The following step explain how to do just that. 
-
-1. Click *File->Import*, then expand the *General* folder and select **Existing Projects into Workspace** and click Next.
-
-    ![lpcxpresso_import.png](http://docs.tinyusb.org/images/lpcxpresso_import.png)
-    
-2. On the next dialog, Click *Browse* and choose the **repo/demos** folder inside the repo. You should see a list of all demo applications. \[**IMPORTANT**\] Make sure the option **Copy projects into workspace** is **CLEAR**, as demo application uses *link folders* and this option may cause problem with the copy import. Then choose any of the demo application and click *Finish*.
-    
-    ![lpcxpresso_import2.png](http://docs.tinyusb.org/images/lpcxpresso_import2.png)
-    
-3. Select the configure corresponding to your development board.
-    
-    ![lpcxpresso_select_board.png](http://docs.tinyusb.org/images/lpcxpresso_select_board.png)
-    
-4. Then select the correct MCU option from project properties then you are ready to go.
-    
-    ![lpcxpresso_mcu.png](http://docs.tinyusb.org/images/lpcxpresso_mcu.png)
-
-*TIPS* Working with eclipse-based IDE like lpcxpresso, you should change the indexer option in *Preferences->C/C++->Indexer* to "active build" to have a better code viewer. Those lines that are opt out by #if will be gray, I found this extremely helpful.
-
-![lpcpresso_indexer](http://docs.tinyusb.org/images/lpcxpresso_indexer.png)
-
-## Keil
-
-It is relatively simple for Keil
-
-1. Open the desired demo project e.g *demos/host/host\_freertos/host_freertos.uvproj*
-2. Select the configure corresponding to your development board and build it. 
-    
-    ![keil_select_board.png](http://docs.tinyusb.org/images/keil_select_board.png) 
-
-## IAR
-
-IAR is just as easy as Keil
-
-1. Open the desired demo project e.g *demos/host/host\_freertos/host_freertos.eww*
-2. Again select the configure corresponding to your development board and build it. 
-    
-    ![iar_select_board.png](http://docs.tinyusb.org/images/iar_select_board.png)
-
-## Configure demo
-
-Application demo is written to have the code excluded if its required option is not enabled in [tusb_config.h](). Some of combination may exceed the 32KB limit of IAR/Keil so you may want to re-configure to disable some class support, decrease CFG_TUSB_DEBUG or increase the compiler optimization level.
-
-In addition, there are some configuration you can change such as
-
-- CFG_UART_BAUDRATE in board.h
-- CFG_PRINTF_TARGET in the specific board header (e.g board_ea4357.h) to either Semihost, Uart, or SWO.
-\ No newline at end of file
+Build and Run example instructions
+\ No newline at end of file