diff options
Diffstat (limited to 'examples/rules.mk')
| -rw-r--r-- | examples/rules.mk | 23 |
1 files changed, 13 insertions, 10 deletions
diff --git a/examples/rules.mk b/examples/rules.mk index ab0373bac..12ec35043 100644 --- a/examples/rules.mk +++ b/examples/rules.mk @@ -43,6 +43,9 @@ all: clean: $(RM) -rf $(BUILD) +#copy-artifact: +# @$(CP) + else # GNU Make build system @@ -100,9 +103,9 @@ endif # Set all as default goal .DEFAULT_GOAL := all -all: $(BUILD)/$(BOARD)-firmware.bin $(BUILD)/$(BOARD)-firmware.hex size +all: $(BUILD)/$(PROJECT).bin $(BUILD)/$(PROJECT).hex size -uf2: $(BUILD)/$(BOARD)-firmware.uf2 +uf2: $(BUILD)/$(PROJECT).uf2 OBJ_DIRS = $(sort $(dir $(OBJ))) $(OBJ): | $(OBJ_DIRS) @@ -113,20 +116,20 @@ else @$(MKDIR) -p $@ endif -$(BUILD)/$(BOARD)-firmware.elf: $(OBJ) +$(BUILD)/$(PROJECT).elf: $(OBJ) @echo LINK $@ @$(CC) -o $@ $(LDFLAGS) $^ -Wl,--start-group $(LIBS) -Wl,--end-group -$(BUILD)/$(BOARD)-firmware.bin: $(BUILD)/$(BOARD)-firmware.elf +$(BUILD)/$(PROJECT).bin: $(BUILD)/$(PROJECT).elf @echo CREATE $@ @$(OBJCOPY) -O binary $^ $@ -$(BUILD)/$(BOARD)-firmware.hex: $(BUILD)/$(BOARD)-firmware.elf +$(BUILD)/$(PROJECT).hex: $(BUILD)/$(PROJECT).elf @echo CREATE $@ @$(OBJCOPY) -O ihex $^ $@ UF2_FAMILY ?= 0x00 -$(BUILD)/$(BOARD)-firmware.uf2: $(BUILD)/$(BOARD)-firmware.hex +$(BUILD)/$(PROJECT).uf2: $(BUILD)/$(PROJECT).hex @echo CREATE $@ $(PYTHON) $(TOP)/tools/uf2/utils/uf2conv.py -f $(UF2_FAMILY) -c -o $@ $^ @@ -150,7 +153,7 @@ $(BUILD)/obj/%.o: %.S @echo AS $(notdir $@) @$(CC) -x assembler-with-cpp $(ASFLAGS) -c -o $@ $< -size: $(BUILD)/$(BOARD)-firmware.elf +size: $(BUILD)/$(PROJECT).elf -@echo '' @$(SIZE) $< -@echo '' @@ -178,7 +181,7 @@ endif JLINK_IF ?= swd # Flash using jlink -flash-jlink: $(BUILD)/$(BOARD)-firmware.hex +flash-jlink: $(BUILD)/$(PROJECT).hex @echo halt > $(BUILD)/$(BOARD).jlink @echo r > $(BUILD)/$(BOARD).jlink @echo loadfile $^ >> $(BUILD)/$(BOARD).jlink @@ -188,11 +191,11 @@ flash-jlink: $(BUILD)/$(BOARD)-firmware.hex $(JLINKEXE) -device $(JLINK_DEVICE) -if $(JLINK_IF) -JTAGConf -1,-1 -speed auto -CommandFile $(BUILD)/$(BOARD).jlink # flash STM32 MCU using stlink with STM32 Cube Programmer CLI -flash-stlink: $(BUILD)/$(BOARD)-firmware.elf +flash-stlink: $(BUILD)/$(PROJECT).elf STM32_Programmer_CLI --connect port=swd --write $< --go # flash with pyocd -flash-pyocd: $(BUILD)/$(BOARD)-firmware.hex +flash-pyocd: $(BUILD)/$(PROJECT).hex pyocd flash -t $(PYOCD_TARGET) $< pyocd reset -t $(PYOCD_TARGET) |