diff options
Diffstat (limited to 'examples')
49 files changed, 677 insertions, 576 deletions
diff --git a/examples/device/audio_4_channel_mic/src/main.c b/examples/device/audio_4_channel_mic/src/main.c index d085dd43a..9c94edd49 100644 --- a/examples/device/audio_4_channel_mic/src/main.c +++ b/examples/device/audio_4_channel_mic/src/main.c @@ -81,7 +81,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); // Init values sampFreq = AUDIO_SAMPLE_RATE; diff --git a/examples/device/audio_4_channel_mic/src/tusb_config.h b/examples/device/audio_4_channel_mic/src/tusb_config.h index 023faa7e2..5cf6d07c3 100644 --- a/examples/device/audio_4_channel_mic/src/tusb_config.h +++ b/examples/device/audio_4_channel_mic/src/tusb_config.h @@ -30,6 +30,20 @@ extern "C" { #endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ + +// RHPort number used for device can be defined by board.mk, default to port 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED +#endif + //-------------------------------------------------------------------- // COMMON CONFIGURATION //-------------------------------------------------------------------- @@ -39,18 +53,19 @@ extern "C" { #error CFG_TUSB_MCU must be defined #endif -#define CFG_TUSB_RHPORT0_MODE OPT_MODE_DEVICE - #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif #ifndef CFG_TUSB_DEBUG -#define CFG_TUSB_DEBUG 0 +#define CFG_TUSB_DEBUG 0 #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -64,7 +79,7 @@ extern "C" { #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- @@ -76,11 +91,11 @@ extern "C" { #endif //------------- CLASS -------------// +#define CFG_TUD_AUDIO 1 #define CFG_TUD_CDC 0 #define CFG_TUD_MSC 0 #define CFG_TUD_HID 0 #define CFG_TUD_MIDI 0 -#define CFG_TUD_AUDIO 1 #define CFG_TUD_VENDOR 0 //-------------------------------------------------------------------- @@ -89,23 +104,23 @@ extern "C" { // Have a look into audio_device.h for all configurations -#define CFG_TUD_AUDIO_FUNC_1_DESC_LEN TUD_AUDIO_MIC_FOUR_CH_DESC_LEN +#define CFG_TUD_AUDIO_FUNC_1_DESC_LEN TUD_AUDIO_MIC_FOUR_CH_DESC_LEN -#define CFG_TUD_AUDIO_FUNC_1_N_AS_INT 1 -#define CFG_TUD_AUDIO_FUNC_1_CTRL_BUF_SZ 64 +#define CFG_TUD_AUDIO_FUNC_1_N_AS_INT 1 +#define CFG_TUD_AUDIO_FUNC_1_CTRL_BUF_SZ 64 -#define CFG_TUD_AUDIO_ENABLE_EP_IN 1 -#define CFG_TUD_AUDIO_FUNC_1_N_BYTES_PER_SAMPLE_TX 2 // This value is not required by the driver, it parses this information from the descriptor once the alternate interface is set by the host - we use it for the setup -#define CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX 4 // This value is not required by the driver, it parses this information from the descriptor once the alternate interface is set by the host - we use it for the setup -#define CFG_TUD_AUDIO_EP_SZ_IN (48 + 1) * CFG_TUD_AUDIO_FUNC_1_N_BYTES_PER_SAMPLE_TX * CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX // 48 Samples (48 kHz) x 2 Bytes/Sample x CFG_TUD_AUDIO_N_CHANNELS_TX Channels - the Windows driver always needs an extra sample per channel of space more, otherwise it complains... found by trial and error -#define CFG_TUD_AUDIO_FUNC_1_EP_IN_SZ_MAX CFG_TUD_AUDIO_EP_SZ_IN -#define CFG_TUD_AUDIO_FUNC_1_EP_IN_SW_BUF_SZ CFG_TUD_AUDIO_EP_SZ_IN +#define CFG_TUD_AUDIO_ENABLE_EP_IN 1 +#define CFG_TUD_AUDIO_FUNC_1_N_BYTES_PER_SAMPLE_TX 2 // This value is not required by the driver, it parses this information from the descriptor once the alternate interface is set by the host - we use it for the setup +#define CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX 4 // This value is not required by the driver, it parses this information from the descriptor once the alternate interface is set by the host - we use it for the setup +#define CFG_TUD_AUDIO_EP_SZ_IN (48 + 1) * CFG_TUD_AUDIO_FUNC_1_N_BYTES_PER_SAMPLE_TX * CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX // 48 Samples (48 kHz) x 2 Bytes/Sample x CFG_TUD_AUDIO_N_CHANNELS_TX Channels - the Windows driver always needs an extra sample per channel of space more, otherwise it complains... found by trial and error +#define CFG_TUD_AUDIO_FUNC_1_EP_IN_SZ_MAX CFG_TUD_AUDIO_EP_SZ_IN +#define CFG_TUD_AUDIO_FUNC_1_EP_IN_SW_BUF_SZ CFG_TUD_AUDIO_EP_SZ_IN -#define CFG_TUD_AUDIO_ENABLE_ENCODING 1 -#define CFG_TUD_AUDIO_ENABLE_TYPE_I_ENCODING 1 -#define CFG_TUD_AUDIO_FUNC_1_CHANNEL_PER_FIFO_TX 2 // One I2S stream contains two channels, each stream is saved within one support FIFO - this value is currently fixed, the driver does not support a changing value -#define CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO (CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX / CFG_TUD_AUDIO_FUNC_1_CHANNEL_PER_FIFO_TX) -#define CFG_TUD_AUDIO_FUNC_1_TX_SUPP_SW_FIFO_SZ (CFG_TUD_AUDIO_EP_SZ_IN / CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO) +#define CFG_TUD_AUDIO_ENABLE_ENCODING 1 +#define CFG_TUD_AUDIO_ENABLE_TYPE_I_ENCODING 1 +#define CFG_TUD_AUDIO_FUNC_1_CHANNEL_PER_FIFO_TX 2 // One I2S stream contains two channels, each stream is saved within one support FIFO - this value is currently fixed, the driver does not support a changing value +#define CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO (CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX / CFG_TUD_AUDIO_FUNC_1_CHANNEL_PER_FIFO_TX) +#define CFG_TUD_AUDIO_FUNC_1_TX_SUPP_SW_FIFO_SZ (CFG_TUD_AUDIO_EP_SZ_IN / CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO) #ifdef __cplusplus } diff --git a/examples/device/audio_test/src/main.c b/examples/device/audio_test/src/main.c index ed13ce993..51f55b772 100644 --- a/examples/device/audio_test/src/main.c +++ b/examples/device/audio_test/src/main.c @@ -82,7 +82,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); // Init values sampFreq = AUDIO_SAMPLE_RATE; diff --git a/examples/device/audio_test/src/tusb_config.h b/examples/device/audio_test/src/tusb_config.h index 9b8514265..355ed1011 100644 --- a/examples/device/audio_test/src/tusb_config.h +++ b/examples/device/audio_test/src/tusb_config.h @@ -30,6 +30,20 @@ extern "C" { #endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ + +// RHPort number used for device can be defined by board.mk, default to port 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED +#endif + //-------------------------------------------------------------------- // COMMON CONFIGURATION //-------------------------------------------------------------------- @@ -39,8 +53,6 @@ extern "C" { #error CFG_TUSB_MCU must be defined #endif -#define CFG_TUSB_RHPORT0_MODE OPT_MODE_DEVICE - #ifndef CFG_TUSB_OS #define CFG_TUSB_OS OPT_OS_NONE #endif @@ -49,6 +61,12 @@ extern "C" { #define CFG_TUSB_DEBUG 0 #endif +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED + // CFG_TUSB_DEBUG is defined by compiler in DEBUG build // #define CFG_TUSB_DEBUG 0 @@ -76,11 +94,11 @@ extern "C" { #endif //------------- CLASS -------------// +#define CFG_TUD_AUDIO 1 #define CFG_TUD_CDC 0 #define CFG_TUD_MSC 0 #define CFG_TUD_HID 0 #define CFG_TUD_MIDI 0 -#define CFG_TUD_AUDIO 1 #define CFG_TUD_VENDOR 0 //-------------------------------------------------------------------- diff --git a/examples/device/board_test/src/tusb_config.h b/examples/device/board_test/src/tusb_config.h index da33729e7..5aea4fd2c 100644 --- a/examples/device/board_test/src/tusb_config.h +++ b/examples/device/board_test/src/tusb_config.h @@ -43,7 +43,9 @@ #define CFG_TUSB_OS OPT_OS_NONE #endif -#define CFG_TUSB_RHPORT0_MODE OPT_MODE_NONE +// This example only test LED & GPIO, disable both device and host stack +#define CFG_TUD_ENABLED 0 +#define CFG_TUH_ENABLED 0 // CFG_TUSB_DEBUG is defined by compiler in DEBUG build // #define CFG_TUSB_DEBUG 0 @@ -63,21 +65,6 @@ #define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif -//-------------------------------------------------------------------- -// DEVICE CONFIGURATION -//-------------------------------------------------------------------- - -#ifndef CFG_TUD_ENDPOINT0_SIZE -#define CFG_TUD_ENDPOINT0_SIZE 64 -#endif - -//------------- CLASS -------------// -#define CFG_TUD_CDC 0 -#define CFG_TUD_MSC 0 -#define CFG_TUD_HID 0 -#define CFG_TUD_MIDI 0 -#define CFG_TUD_VENDOR 0 - #ifdef __cplusplus } #endif diff --git a/examples/device/cdc_dual_ports/src/main.c b/examples/device/cdc_dual_ports/src/main.c index 34cd29edd..6053a3b81 100644 --- a/examples/device/cdc_dual_ports/src/main.c +++ b/examples/device/cdc_dual_ports/src/main.c @@ -39,7 +39,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/cdc_dual_ports/src/tusb_config.h b/examples/device/cdc_dual_ports/src/tusb_config.h index f93606092..070f08ed1 100644 --- a/examples/device/cdc_dual_ports/src/tusb_config.h +++ b/examples/device/cdc_dual_ports/src/tusb_config.h @@ -30,41 +30,42 @@ extern "C" { #endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ + +// RHPort number used for device can be defined by board.mk, default to port 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED +#endif + //-------------------------------------------------------------------- // COMMON CONFIGURATION //-------------------------------------------------------------------- // defined by board.mk #ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined +#error CFG_TUSB_MCU must be defined #endif -// RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 -#endif - -// RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef CFG_TUSB_OS +#define CFG_TUSB_OS OPT_OS_NONE #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 #endif -#ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE -#endif +// Enable Device stack +#define CFG_TUD_ENABLED 1 -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put diff --git a/examples/device/cdc_msc/src/main.c b/examples/device/cdc_msc/src/main.c index 131ae6549..c3666763b 100644 --- a/examples/device/cdc_msc/src/main.c +++ b/examples/device/cdc_msc/src/main.c @@ -54,7 +54,9 @@ void cdc_task(void); int main(void) { board_init(); - tusb_init(); + + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/cdc_msc/src/tusb_config.h b/examples/device/cdc_msc/src/tusb_config.h index 6507cef19..03e0e649c 100644 --- a/examples/device/cdc_msc/src/tusb_config.h +++ b/examples/device/cdc_msc/src/tusb_config.h @@ -30,42 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// Common Configuration +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif -// This example doesn't use an RTOS #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -79,7 +79,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/cdc_msc_freertos/src/main.c b/examples/device/cdc_msc_freertos/src/main.c index a5e907199..755220c13 100644 --- a/examples/device/cdc_msc_freertos/src/main.c +++ b/examples/device/cdc_msc_freertos/src/main.c @@ -123,9 +123,10 @@ void usb_device_task(void* param) { (void) param; + // init device stack on configured roothub port // This should be called after scheduler/kernel is started. // Otherwise it could cause kernel issue since USB IRQ handler does use RTOS queue API. - tusb_init(); + tud_init(BOARD_TUD_RHPORT); // RTOS forever loop while (1) diff --git a/examples/device/cdc_msc_freertos/src/tusb_config.h b/examples/device/cdc_msc_freertos/src/tusb_config.h index 55e84c62d..0ec8896b9 100644 --- a/examples/device/cdc_msc_freertos/src/tusb_config.h +++ b/examples/device/cdc_msc_freertos/src/tusb_config.h @@ -30,53 +30,48 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to Highspeed for MCU with internal HighSpeed PHY (can be port specific), otherwise FullSpeed -#ifndef BOARD_DEVICE_RHPORT_SPEED - #if (CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX || \ - CFG_TUSB_MCU == OPT_MCU_NUC505 || CFG_TUSB_MCU == OPT_MCU_CXD56) - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_HIGH_SPEED - #else - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_FULL_SPEED - #endif +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by board.mk +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif // This examples use FreeRTOS -#define CFG_TUSB_OS OPT_OS_FREERTOS +#define CFG_TUSB_OS OPT_OS_FREERTOS // Espressif IDF requires "freertos/" prefix in include path #if TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) - #define CFG_TUSB_OS_INC_PATH freertos/ +#define CFG_TUSB_OS_INC_PATH freertos/ #endif // can be defined by compiler in DEBUG build #ifndef CFG_TUSB_DEBUG - #define CFG_TUSB_DEBUG 0 +#define CFG_TUSB_DEBUG 0 #endif +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED + /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put * into those specific section. @@ -89,7 +84,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- @@ -97,7 +92,7 @@ //-------------------------------------------------------------------- #ifndef CFG_TUD_ENDPOINT0_SIZE -#define CFG_TUD_ENDPOINT0_SIZE 64 +#define CFG_TUD_ENDPOINT0_SIZE 64 #endif //------------- CLASS -------------// diff --git a/examples/device/dfu/src/main.c b/examples/device/dfu/src/main.c index 5c8464526..6bb183819 100644 --- a/examples/device/dfu/src/main.c +++ b/examples/device/dfu/src/main.c @@ -74,7 +74,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/dfu/src/tusb_config.h b/examples/device/dfu/src/tusb_config.h index d4779b2e1..38064147c 100644 --- a/examples/device/dfu/src/tusb_config.h +++ b/examples/device/dfu/src/tusb_config.h @@ -12,41 +12,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -60,7 +61,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- @@ -72,10 +73,10 @@ #endif //------------- CLASS -------------// -#define CFG_TUD_DFU 1 +#define CFG_TUD_DFU 1 // DFU buffer size, it has to be set to the buffer size used in TUD_DFU_DESCRIPTOR -#define CFG_TUD_DFU_XFER_BUFSIZE ( OPT_MODE_HIGH_SPEED ? 512 : 64 ) +#define CFG_TUD_DFU_XFER_BUFSIZE (TUD_OPT_HIGH_SPEED ? 512 : 64) #ifdef __cplusplus } diff --git a/examples/device/dfu_runtime/src/main.c b/examples/device/dfu_runtime/src/main.c index 823c71ae5..55b380353 100644 --- a/examples/device/dfu_runtime/src/main.c +++ b/examples/device/dfu_runtime/src/main.c @@ -69,7 +69,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/dfu_runtime/src/tusb_config.h b/examples/device/dfu_runtime/src/tusb_config.h index e15ae7997..fa1ae6ed3 100644 --- a/examples/device/dfu_runtime/src/tusb_config.h +++ b/examples/device/dfu_runtime/src/tusb_config.h @@ -12,41 +12,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put diff --git a/examples/device/dynamic_configuration/src/main.c b/examples/device/dynamic_configuration/src/main.c index 4c10f55b0..95f8b8286 100644 --- a/examples/device/dynamic_configuration/src/main.c +++ b/examples/device/dynamic_configuration/src/main.c @@ -55,7 +55,9 @@ void midi_task(void); int main(void) { board_init(); - tusb_init(); + + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/dynamic_configuration/src/tusb_config.h b/examples/device/dynamic_configuration/src/tusb_config.h index ddc295dcc..b9b3878cc 100644 --- a/examples/device/dynamic_configuration/src/tusb_config.h +++ b/examples/device/dynamic_configuration/src/tusb_config.h @@ -30,41 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -78,7 +79,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/hid_boot_interface/src/main.c b/examples/device/hid_boot_interface/src/main.c index e5e2f6856..21cdb383d 100644 --- a/examples/device/hid_boot_interface/src/main.c +++ b/examples/device/hid_boot_interface/src/main.c @@ -55,7 +55,9 @@ void hid_task(void); int main(void) { board_init(); - tusb_init(); + + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/hid_boot_interface/src/tusb_config.h b/examples/device/hid_boot_interface/src/tusb_config.h index 8bc85b722..52723e09f 100644 --- a/examples/device/hid_boot_interface/src/tusb_config.h +++ b/examples/device/hid_boot_interface/src/tusb_config.h @@ -30,45 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif - -// Use raspberry pio-usb for device -// #define CFG_TUD_RPI_PIO_USB 1 -// #define BOARD_DEVICE_RHPORT_NUM 1 +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -82,7 +79,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/hid_composite/src/main.c b/examples/device/hid_composite/src/main.c index fd25e620a..bc2347ab8 100644 --- a/examples/device/hid_composite/src/main.c +++ b/examples/device/hid_composite/src/main.c @@ -56,7 +56,9 @@ void hid_task(void); int main(void) { board_init(); - tusb_init(); + + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/hid_composite/src/tusb_config.h b/examples/device/hid_composite/src/tusb_config.h index d0f2b513f..6bd32c427 100644 --- a/examples/device/hid_composite/src/tusb_config.h +++ b/examples/device/hid_composite/src/tusb_config.h @@ -30,41 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put diff --git a/examples/device/hid_composite_freertos/src/main.c b/examples/device/hid_composite_freertos/src/main.c index 317b64611..1030f3d05 100644 --- a/examples/device/hid_composite_freertos/src/main.c +++ b/examples/device/hid_composite_freertos/src/main.c @@ -125,9 +125,10 @@ void usb_device_task(void* param) { (void) param; + // init device stack on configured roothub port // This should be called after scheduler/kernel is started. // Otherwise it could cause kernel issue since USB IRQ handler does use RTOS queue API. - tusb_init(); + tud_init(BOARD_TUD_RHPORT); // RTOS forever loop while (1) diff --git a/examples/device/hid_composite_freertos/src/tusb_config.h b/examples/device/hid_composite_freertos/src/tusb_config.h index 7522bd714..935ae9453 100644 --- a/examples/device/hid_composite_freertos/src/tusb_config.h +++ b/examples/device/hid_composite_freertos/src/tusb_config.h @@ -30,48 +30,48 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by board.mk +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif // This examples use FreeRTOS -#define CFG_TUSB_OS OPT_OS_FREERTOS +#define CFG_TUSB_OS OPT_OS_FREERTOS // Espressif IDF requires "freertos/" prefix in include path #if TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) - #define CFG_TUSB_OS_INC_PATH freertos/ +#define CFG_TUSB_OS_INC_PATH freertos/ #endif - +// can be defined by compiler in DEBUG build #ifndef CFG_TUSB_DEBUG -#define CFG_TUSB_DEBUG 0 +#define CFG_TUSB_DEBUG 0 #endif +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED + /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put * into those specific section. diff --git a/examples/device/hid_generic_inout/src/main.c b/examples/device/hid_generic_inout/src/main.c index 32185560e..5b7daf118 100644 --- a/examples/device/hid_generic_inout/src/main.c +++ b/examples/device/hid_generic_inout/src/main.c @@ -80,7 +80,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/hid_generic_inout/src/tusb_config.h b/examples/device/hid_generic_inout/src/tusb_config.h index 9db50269c..98143ac4d 100644 --- a/examples/device/hid_generic_inout/src/tusb_config.h +++ b/examples/device/hid_generic_inout/src/tusb_config.h @@ -30,41 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -78,7 +79,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/hid_multiple_interface/src/main.c b/examples/device/hid_multiple_interface/src/main.c index 7cb1d75a7..29ba74398 100644 --- a/examples/device/hid_multiple_interface/src/main.c +++ b/examples/device/hid_multiple_interface/src/main.c @@ -60,7 +60,9 @@ void hid_task(void); int main(void) { board_init(); - tusb_init(); + + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/hid_multiple_interface/src/tusb_config.h b/examples/device/hid_multiple_interface/src/tusb_config.h index 32e8c2843..49dc962fe 100644 --- a/examples/device/hid_multiple_interface/src/tusb_config.h +++ b/examples/device/hid_multiple_interface/src/tusb_config.h @@ -30,41 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put diff --git a/examples/device/midi_test/src/main.c b/examples/device/midi_test/src/main.c index 193748477..b47d1af76 100644 --- a/examples/device/midi_test/src/main.c +++ b/examples/device/midi_test/src/main.c @@ -62,7 +62,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/midi_test/src/tusb_config.h b/examples/device/midi_test/src/tusb_config.h index 967c71403..314dde438 100644 --- a/examples/device/midi_test/src/tusb_config.h +++ b/examples/device/midi_test/src/tusb_config.h @@ -30,41 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -78,7 +79,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/msc_dual_lun/src/main.c b/examples/device/msc_dual_lun/src/main.c index 0293261ad..96790d20c 100644 --- a/examples/device/msc_dual_lun/src/main.c +++ b/examples/device/msc_dual_lun/src/main.c @@ -54,7 +54,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/msc_dual_lun/src/tusb_config.h b/examples/device/msc_dual_lun/src/tusb_config.h index f617f5a4c..9cbbbade9 100644 --- a/examples/device/msc_dual_lun/src/tusb_config.h +++ b/examples/device/msc_dual_lun/src/tusb_config.h @@ -30,41 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -78,7 +79,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/net_lwip_webserver/src/main.c b/examples/device/net_lwip_webserver/src/main.c index 30bb3577b..33b4d38b6 100644 --- a/examples/device/net_lwip_webserver/src/main.c +++ b/examples/device/net_lwip_webserver/src/main.c @@ -228,7 +228,9 @@ int main(void) { /* initialize TinyUSB */ board_init(); - tusb_init(); + + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); /* initialize lwip, dhcp-server, dns-server, and http */ init_lwip(); diff --git a/examples/device/net_lwip_webserver/src/tusb_config.h b/examples/device/net_lwip_webserver/src/tusb_config.h index b1b48598b..fe72ecdfe 100644 --- a/examples/device/net_lwip_webserver/src/tusb_config.h +++ b/examples/device/net_lwip_webserver/src/tusb_config.h @@ -30,41 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// Common Configuration +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -78,7 +79,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/uac2_headset/src/main.c b/examples/device/uac2_headset/src/main.c index bbaacd975..a8d204eaa 100644 --- a/examples/device/uac2_headset/src/main.c +++ b/examples/device/uac2_headset/src/main.c @@ -102,7 +102,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); TU_LOG1("Headset running\r\n"); diff --git a/examples/device/uac2_headset/src/tusb_config.h b/examples/device/uac2_headset/src/tusb_config.h index 2a1189a79..1a3e23e95 100644 --- a/examples/device/uac2_headset/src/tusb_config.h +++ b/examples/device/uac2_headset/src/tusb_config.h @@ -31,30 +31,45 @@ extern "C" { #endif +#include "usb_descriptors.h" + +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ + +// RHPort number used for device can be defined by board.mk, default to port 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED +#endif + //-------------------------------------------------------------------- -// COMMON CONFIGURATION +// Common Configuration //-------------------------------------------------------------------- -#include "usb_descriptors.h" - // defined by compiler flags for flexibility #ifndef CFG_TUSB_MCU #error CFG_TUSB_MCU must be defined #endif -#define CFG_TUSB_RHPORT0_MODE OPT_MODE_DEVICE - #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif #ifndef CFG_TUSB_DEBUG -// Can be set during compilation i.e.: make LOG=<value for CFG_TUSB_DEBUG> BOARD=<bsp> -// Keep in mind that enabling logs when data is streaming can disrupt data flow. -// It can be very helpful though when audio unit requests are tested/debugged. -#define CFG_TUSB_DEBUG 0 +#define CFG_TUSB_DEBUG 0 #endif +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED + /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put * into those specific section. @@ -67,7 +82,7 @@ extern "C" { #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/usbtmc/src/main.c b/examples/device/usbtmc/src/main.c index 1fce48f45..6945d8743 100644 --- a/examples/device/usbtmc/src/main.c +++ b/examples/device/usbtmc/src/main.c @@ -54,7 +54,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/usbtmc/src/tusb_config.h b/examples/device/usbtmc/src/tusb_config.h index 5b2215be5..ab486b108 100644 --- a/examples/device/usbtmc/src/tusb_config.h +++ b/examples/device/usbtmc/src/tusb_config.h @@ -12,41 +12,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// Common Configuration +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -60,7 +61,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/video_capture/src/main.c b/examples/device/video_capture/src/main.c index f1d48385f..4028352da 100644 --- a/examples/device/video_capture/src/main.c +++ b/examples/device/video_capture/src/main.c @@ -55,7 +55,9 @@ void video_task(void); int main(void) { board_init(); - tusb_init(); + + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/video_capture/src/tusb_config.h b/examples/device/video_capture/src/tusb_config.h index 3a079e66b..e567ba669 100644 --- a/examples/device/video_capture/src/tusb_config.h +++ b/examples/device/video_capture/src/tusb_config.h @@ -30,37 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// Common Configuration +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif -// This example doesn't use an RTOS #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE +#endif + +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -74,7 +79,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/device/webusb_serial/src/main.c b/examples/device/webusb_serial/src/main.c index 2716825f8..8eaad7706 100644 --- a/examples/device/webusb_serial/src/main.c +++ b/examples/device/webusb_serial/src/main.c @@ -93,7 +93,8 @@ int main(void) { board_init(); - tusb_init(); + // init device stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); while (1) { diff --git a/examples/device/webusb_serial/src/tusb_config.h b/examples/device/webusb_serial/src/tusb_config.h index f5e4694e3..fde732b9e 100644 --- a/examples/device/webusb_serial/src/tusb_config.h +++ b/examples/device/webusb_serial/src/tusb_config.h @@ -30,41 +30,42 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif // RHPort max operational speed can defined by board.mk -// Default to max (auto) speed for MCU with internal HighSpeed PHY -#ifndef BOARD_DEVICE_RHPORT_SPEED - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_DEFAULT_SPEED +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +//-------------------------------------------------------------------- +// Common Configuration +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#define CFG_TUSB_OS OPT_OS_NONE #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Device stack +#define CFG_TUD_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put @@ -78,7 +79,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/dual/host_hid_to_device_cdc/src/main.c b/examples/dual/host_hid_to_device_cdc/src/main.c index 62ecb2c3f..6a25a28da 100644 --- a/examples/dual/host_hid_to_device_cdc/src/main.c +++ b/examples/dual/host_hid_to_device_cdc/src/main.c @@ -79,7 +79,9 @@ int main(void) printf("TinyUSB Host HID <-> Device CDC Example\r\n"); - tusb_init(); + // init device and host stack on configured roothub port + tud_init(BOARD_TUD_RHPORT); + tuh_init(BOARD_TUH_RHPORT); while (1) { diff --git a/examples/dual/host_hid_to_device_cdc/src/tusb_config.h b/examples/dual/host_hid_to_device_cdc/src/tusb_config.h index 0fa4899a9..f749bd712 100644 --- a/examples/dual/host_hid_to_device_cdc/src/tusb_config.h +++ b/examples/dual/host_hid_to_device_cdc/src/tusb_config.h @@ -30,75 +30,61 @@ extern "C" { #endif -//-------------------------------------------------------------------- -// COMMON CONFIGURATION -//-------------------------------------------------------------------- - -// defined by board.mk -#ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined -#endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ // RHPort number used for device can be defined by board.mk, default to port 0 -#ifndef BOARD_DEVICE_RHPORT_NUM - #define BOARD_DEVICE_RHPORT_NUM 0 +#ifndef BOARD_TUD_RHPORT +#define BOARD_TUD_RHPORT 0 #endif -// RHPort number used for device can be defined by board.mk, default to port 1 -#ifndef BOARD_HOST_RHPORT_NUM - #define BOARD_HOST_RHPORT_NUM 1 +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUD_MAX_SPEED +#define BOARD_TUD_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// Use raspberry pio-usb for host -#define CFG_TUH_RPI_PIO_USB 1 +// RHPort number used for host can be defined by board.mk, default to port 1 +#ifndef BOARD_TUH_RHPORT +#define BOARD_TUH_RHPORT 1 +#endif // RHPort max operational speed can defined by board.mk -// Default to Highspeed for MCU with internal HighSpeed PHY (can be port specific), otherwise FullSpeed -#ifndef BOARD_DEVICE_RHPORT_SPEED - #if TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX, OPT_MCU_MIMXRT10XX, OPT_MCU_NUC505) ||\ - TU_CHECK_MCU(OPT_MCU_CXD56, OPT_MCU_SAMX7X, OPT_MCU_BCM2711) ||\ - TU_CHECK_MCU(OPT_MCU_FT90X, OPT_MCU_FT93X) - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_HIGH_SPEED - #else - #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_FULL_SPEED - #endif +#ifndef BOARD_TUH_MAX_SPEED +#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif -// RHPort max operational speed can defined by board.mk -// Default to Highspeed for MCU with internal HighSpeed PHY (can be port specific), otherwise FullSpeed -#ifndef BOARD_HOST_RHPORT_SPEED - #if TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX, OPT_MCU_MIMXRT10XX, OPT_MCU_NUC505) ||\ - TU_CHECK_MCU(OPT_MCU_CXD56, OPT_MCU_SAMX7X, OPT_MCU_BCM2711) ||\ - TU_CHECK_MCU(OPT_MCU_FT90X, OPT_MCU_FT93X) - #define BOARD_HOST_RHPORT_SPEED OPT_MODE_HIGH_SPEED - #else - #define BOARD_HOST_RHPORT_SPEED OPT_MODE_FULL_SPEED - #endif +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_DEVICE_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#elif BOARD_DEVICE_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +#ifndef CFG_TUSB_OS +#define CFG_TUSB_OS OPT_OS_NONE #endif -// Device mode with rhport and speed defined by board.mk -#if BOARD_HOST_RHPORT_NUM == 0 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_HOST | BOARD_HOST_RHPORT_SPEED) -#elif BOARD_HOST_RHPORT_NUM == 1 - #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_HOST | BOARD_HOST_RHPORT_SPEED) -#else - #error "Incorrect RHPort configuration" +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 #endif -// This example doesn't use an RTOS -#ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +// Enable Device stack, Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUD_ENABLED 1 +#define CFG_TUD_MAX_SPEED BOARD_TUD_MAX_SPEED + +// Enable Host stack, Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUH_ENABLED 1 +#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED + +#if CFG_TUSB_MCU == OPT_MCU_RP2040 +// Use pico-pio-usb as host controller for raspberry rp2040 +#define CFG_TUH_RPI_PIO_USB 1 #endif + // CFG_TUSB_DEBUG is defined by compiler in DEBUG build // #define CFG_TUSB_DEBUG 0 @@ -114,7 +100,7 @@ #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) #endif //-------------------------------------------------------------------- diff --git a/examples/host/bare_api/src/main.c b/examples/host/bare_api/src/main.c index eb3f7d8d7..2cc05d34d 100644 --- a/examples/host/bare_api/src/main.c +++ b/examples/host/bare_api/src/main.c @@ -62,8 +62,10 @@ int main(void) { board_init(); - printf("TinyUSB Host HID Controller Example\r\n"); - tusb_init(); + printf("TinyUSB Bare API Example\r\n"); + + // init host stack on configured roothub port + tuh_init(BOARD_TUH_RHPORT); while (1) { diff --git a/examples/host/bare_api/src/tusb_config.h b/examples/host/bare_api/src/tusb_config.h index 9b789290d..ed0aaf7da 100644 --- a/examples/host/bare_api/src/tusb_config.h +++ b/examples/host/bare_api/src/tusb_config.h @@ -30,27 +30,42 @@ extern "C" { #endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ + +// RHPort number used for host can be defined by board.mk, default to port 0 +#ifndef BOARD_TUH_RHPORT +#define BOARD_TUH_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUH_MAX_SPEED +#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED +#endif + //-------------------------------------------------------------------- // COMMON CONFIGURATION //-------------------------------------------------------------------- // defined by compiler flags for flexibility #ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined +#error CFG_TUSB_MCU must be defined #endif -#if CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_HOST | OPT_MODE_HIGH_SPEED) -#else - #define CFG_TUSB_RHPORT0_MODE OPT_MODE_HOST +#ifndef CFG_TUSB_OS +#define CFG_TUSB_OS OPT_OS_NONE #endif -#ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +// Enable Host stack +#define CFG_TUH_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put diff --git a/examples/host/cdc_msc_hid/src/main.c b/examples/host/cdc_msc_hid/src/main.c index 0fc7ef146..664cbf035 100644 --- a/examples/host/cdc_msc_hid/src/main.c +++ b/examples/host/cdc_msc_hid/src/main.c @@ -45,7 +45,8 @@ int main(void) printf("TinyUSB Host CDC MSC HID Example\r\n"); - tusb_init(); + // init host stack on configured roothub port + tuh_init(BOARD_TUH_RHPORT); while (1) { diff --git a/examples/host/cdc_msc_hid/src/tusb_config.h b/examples/host/cdc_msc_hid/src/tusb_config.h index e9e68cf5a..76d96b556 100644 --- a/examples/host/cdc_msc_hid/src/tusb_config.h +++ b/examples/host/cdc_msc_hid/src/tusb_config.h @@ -30,34 +30,42 @@ extern "C" { #endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ + +// RHPort number used for host can be defined by board.mk, default to port 0 +#ifndef BOARD_TUH_RHPORT +#define BOARD_TUH_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUH_MAX_SPEED +#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED +#endif + //-------------------------------------------------------------------- // COMMON CONFIGURATION //-------------------------------------------------------------------- // defined by compiler flags for flexibility #ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined +#error CFG_TUSB_MCU must be defined #endif -// Use raspberry pio-usb for host -// #define CFG_TUH_RPI_PIO_USB 1 -// #define CFG_TUH_RPI_PIO_USB 1 - -#if CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_HOST | OPT_MODE_HIGH_SPEED) -#elif defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB - // rp2040: port0 is native, port 1 for PIO-USB - #define CFG_TUSB_RHPORT1_MODE OPT_MODE_HOST -#else - #define CFG_TUSB_RHPORT0_MODE OPT_MODE_HOST +#ifndef CFG_TUSB_OS +#define CFG_TUSB_OS OPT_OS_NONE #endif -#ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +// Enable Host stack +#define CFG_TUH_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put diff --git a/examples/host/hid_controller/src/main.c b/examples/host/hid_controller/src/main.c index b9b37a4d2..299a3ff10 100644 --- a/examples/host/hid_controller/src/main.c +++ b/examples/host/hid_controller/src/main.c @@ -49,9 +49,10 @@ int main(void) board_init(); printf("TinyUSB Host HID Controller Example\r\n"); - printf("Note: Events only displayed for explictly supported controllers\r\n"); + printf("Note: Events only displayed for explicit supported controllers\r\n"); - tusb_init(); + // init host stack on configured roothub port + tuh_init(BOARD_TUH_RHPORT); while (1) { diff --git a/examples/host/hid_controller/src/tusb_config.h b/examples/host/hid_controller/src/tusb_config.h index 74b471ae4..475b9ca8f 100644 --- a/examples/host/hid_controller/src/tusb_config.h +++ b/examples/host/hid_controller/src/tusb_config.h @@ -30,27 +30,42 @@ extern "C" { #endif +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ + +// RHPort number used for host can be defined by board.mk, default to port 0 +#ifndef BOARD_TUH_RHPORT +#define BOARD_TUH_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUH_MAX_SPEED +#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED +#endif + //-------------------------------------------------------------------- // COMMON CONFIGURATION //-------------------------------------------------------------------- // defined by compiler flags for flexibility #ifndef CFG_TUSB_MCU - #error CFG_TUSB_MCU must be defined +#error CFG_TUSB_MCU must be defined #endif -#if CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_HOST | OPT_MODE_HIGH_SPEED) -#else - #define CFG_TUSB_RHPORT0_MODE OPT_MODE_HOST +#ifndef CFG_TUSB_OS +#define CFG_TUSB_OS OPT_OS_NONE #endif -#ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 #endif -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +// Enable Host stack +#define CFG_TUH_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put |