diff options
Diffstat (limited to 'src/portable')
95 files changed, 2422 insertions, 3173 deletions
diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 971dbd62e..a3aefb829 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2023 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2023 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -82,6 +63,11 @@ enum { }; enum { + TIME_TO_EXIT_SUSPEND_MS = 4u, // datasheet: PWRDOWN = 1 to 0 to OSCOKIRQ = 3 ms + 1 ms margin + TIME_CHIPRES_DELAY_MS = 2u // CHIPRES hold: 2 guarantees >= 1 ms actual despite ms-tick quantization +}; + +enum { CPUCTL_IE = 1u << 0, CPUCTL_PULSEWID0 = 1u << 6, CPUCTL_PULSEWID1 = 1u << 7, @@ -490,8 +476,6 @@ bool hcd_init(uint8_t rhport, const tusb_rhport_init_t* rh_init) { _hcd_data.spi_mutex = osal_mutex_create(&_hcd_data.spi_mutexdef); #endif - // NOTE: driver does not seem to work without nRST pin signal - // full duplex, interrupt negative edge reg_write(rhport, PINCTL_ADDR, _tuh_cfg.pinctl | PINCTL_FDUPSPI, false); @@ -501,12 +485,21 @@ bool hcd_init(uint8_t rhport, const tusb_rhport_init_t* rh_init) { TU_LOG2_HEX(revision); TU_ASSERT(revision == 0x01 || revision == 0x12 || revision == 0x13, false); - // reset + // Software reset via CHIPRES. Per the Programming Guide, CHIPRES stops the internal oscillator; + // clearing it restarts the oscillator, and OSCOKIRQ latches on the resulting OSCOK 0->1 edge. + // Back-to-back writes hold reset for only ~us, too short for the high-Q crystal to actually stop, + // so no edge is generated and OSCOK never re-latches - this is the startup hang. Hold reset >= 1 ms + // (datasheet "PWRDOWN = 1 to oscillator stop = 5 us") so the oscillator fully stops and the edge fires. reg_write(rhport, USBCTL_ADDR, USBCTL_CHIPRES, false); + const uint32_t reset_start_ms = tusb_time_millis_api(); + while (tusb_time_millis_api() - reset_start_ms < TIME_CHIPRES_DELAY_MS) {} // hold reset so the oscillator stops reg_write(rhport, USBCTL_ADDR, 0, false); - while( !(reg_read(rhport, USBIRQ_ADDR, false) & USBIRQ_OSCOK_IRQ) ) { - // wait for oscillator to stabilize - } + + // Wait for OSCOK (12 MHz oscillator + 48 MHz PLL relock). Bounded as a safety net, so the host never + // hangs if the edge is still missed on some board - the clock is running regardless. + const uint32_t oscok_start_ms = tusb_time_millis_api(); + while (!(reg_read(rhport, USBIRQ_ADDR, false) & USBIRQ_OSCOK_IRQ) && + (tusb_time_millis_api() - oscok_start_ms < TIME_TO_EXIT_SUSPEND_MS)) {} // Mode: Host and DP/DM pull down mode_write(rhport, MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST, false); diff --git a/src/portable/analog/max3421/hcd_max3421.h b/src/portable/analog/max3421/hcd_max3421.h index 4631fa21a..38d78c8c2 100644 --- a/src/portable/analog/max3421/hcd_max3421.h +++ b/src/portable/analog/max3421/hcd_max3421.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2025 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2025 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/bridgetek/ft9xx/dcd_ft9xx.c b/src/portable/bridgetek/ft9xx/dcd_ft9xx.c index 89477b9ac..f6c8507db 100644 --- a/src/portable/bridgetek/ft9xx/dcd_ft9xx.c +++ b/src/portable/bridgetek/ft9xx/dcd_ft9xx.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright 2021 Bridgetek Pte Ltd - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright 2021 Bridgetek Pte Ltd + * SPDX-FileCopyrightText: Copyright (c) 2021 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/chipidea/ci_fs/ci_fs_kinetis.h b/src/portable/chipidea/ci_fs/ci_fs_kinetis.h index 31e14a546..e9370140d 100644 --- a/src/portable/chipidea/ci_fs/ci_fs_kinetis.h +++ b/src/portable/chipidea/ci_fs/ci_fs_kinetis.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2023 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2023 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/chipidea/ci_fs/ci_fs_mcx.h b/src/portable/chipidea/ci_fs/ci_fs_mcx.h index 4b93a03a7..425265cca 100644 --- a/src/portable/chipidea/ci_fs/ci_fs_mcx.h +++ b/src/portable/chipidea/ci_fs/ci_fs_mcx.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2023 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2023 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/chipidea/ci_fs/ci_fs_type.h b/src/portable/chipidea/ci_fs/ci_fs_type.h index 5a5e53fb0..857a75253 100644 --- a/src/portable/chipidea/ci_fs/ci_fs_type.h +++ b/src/portable/chipidea/ci_fs/ci_fs_type.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2023 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2023 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -46,6 +27,60 @@ extern "C" { // align 4 is used to get rid of reserved fields #define _va32 volatile TU_ATTR_ALIGNED(4) +//--------------------------------------------------------------------+ +// Buffer Descriptor Table (BDT) - shared by the device (dcd) and host (hcd) drivers +// since both target the same ChipIdea-FS silicon. Keep the layout in one place so a +// fix cannot silently drift between the two drivers. +//--------------------------------------------------------------------+ + +// Token PID values reported in the BDT tok_pid field / written to the TOKEN register. +// The device driver only uses OUT/IN/SETUP; the rest are host-only. +enum { + TOK_PID_OUT = 0x1u, + TOK_PID_IN = 0x9u, + TOK_PID_SETUP = 0xDu, + TOK_PID_DATA0 = 0x3u, + TOK_PID_DATA1 = 0xbu, + TOK_PID_ACK = 0x2u, + TOK_PID_STALL = 0xeu, + TOK_PID_NAK = 0xau, + TOK_PID_BUSTO = 0x0u, + TOK_PID_ERR = 0xfu, +}; + +// Note: this header is included before the CMSIS device header, so use plain `volatile` +// rather than CMSIS `__IO`. +typedef struct TU_ATTR_PACKED +{ + union { + uint32_t head; + struct { + union { + struct { + uint16_t : 2; + volatile uint16_t tok_pid : 4; + uint16_t data : 1; + volatile uint16_t own : 1; + uint16_t : 8; + }; + struct { + uint16_t : 2; + uint16_t bdt_stall : 1; + uint16_t dts : 1; + uint16_t ninc : 1; + uint16_t keep : 1; + uint16_t : 10; + }; + }; + volatile uint16_t bc : 10; + uint16_t : 6; + }; + }; + uint8_t *addr; +}buffer_descriptor_t; + +TU_VERIFY_STATIC( sizeof(buffer_descriptor_t) == 8, "size is not correct" ); + typedef struct { _va32 uint8_t PER_ID; // [00] Peripheral ID register _va32 uint8_t ID_COMP; // [04] Peripheral ID complement register diff --git a/src/portable/chipidea/ci_fs/dcd_ci_fs.c b/src/portable/chipidea/ci_fs/dcd_ci_fs.c index 62df1a6d5..295f2e578 100644 --- a/src/portable/chipidea/ci_fs/dcd_ci_fs.c +++ b/src/portable/chipidea/ci_fs/dcd_ci_fs.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2020 Koji Kitayama - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2020 Koji Kitayama + * SPDX-FileCopyrightText: Copyright (c) 2020 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -42,43 +24,7 @@ //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM DECLARATION //--------------------------------------------------------------------+ - -enum { - TOK_PID_OUT = 0x1u, - TOK_PID_IN = 0x9u, - TOK_PID_SETUP = 0xDu, -}; - -typedef struct TU_ATTR_PACKED -{ - union { - uint32_t head; - struct { - union { - struct { - uint16_t : 2; - __IO uint16_t tok_pid : 4; - uint16_t data : 1; - __IO uint16_t own : 1; - uint16_t : 8; - }; - struct { - uint16_t : 2; - uint16_t bdt_stall : 1; - uint16_t dts : 1; - uint16_t ninc : 1; - uint16_t keep : 1; - uint16_t : 10; - }; - }; - __IO uint16_t bc : 10; - uint16_t : 6; - }; - }; - uint8_t *addr; -}buffer_descriptor_t; - -TU_VERIFY_STATIC( sizeof(buffer_descriptor_t) == 8, "size is not correct" ); +// TOK_PID_* and buffer_descriptor_t are shared with the host driver in ci_fs_type.h typedef struct TU_ATTR_PACKED { @@ -193,6 +139,17 @@ static void process_tokdne(uint8_t rhport) return; } const unsigned length = ep->length; + + /* Transfer is complete. For OUT, a multi-packet transfer speculatively arms the + * sibling (even/odd) BDT to avoid NAK. When the transfer ends early - e.g. the host + * sends a short packet before filling both buffers - that sibling is left armed + * (own=1). A leftover armed BDT desyncs the even/odd ping-pong so the next OUT + * packet lands in the wrong buffer half (buffer + max_packet_size instead of + * buffer), making the stack read stale data. Disarm it here. */ + if (dir == TUSB_DIR_OUT) { + _dcd.bdt[epnum][dir][odd ^ 1].own = 0; + } + dcd_event_xfer_complete(rhport, tu_edpt_addr(epnum, dir), length - remaining, XFER_RESULT_SUCCESS, true); diff --git a/src/portable/nxp/khci/hcd_khci.c b/src/portable/chipidea/ci_fs/hcd_ci_fs.c index 45732a866..a6f5405b5 100644 --- a/src/portable/nxp/khci/hcd_khci.c +++ b/src/portable/chipidea/ci_fs/hcd_ci_fs.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021 Koji Kitayama - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021 Koji Kitayama + * SPDX-FileCopyrightText: Copyright (c) 2021 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -28,63 +10,28 @@ #if CFG_TUH_ENABLED && defined(TUP_USBIP_CHIPIDEA_FS) -#ifdef TUP_USBIP_CHIPIDEA_FS_KINETIS +#include "host/hcd.h" +#include "host/usbh.h" +#include "ci_fs_type.h" + +// Host is currently only available on NXP Kinetis. The ChipIdea-FS host controller +// interface is register-compatible via ci_fs_regs_t. Unlike the device driver, the host +// driver does not include the ci_fs_<family>.h header because those define the device +// dcd_int_enable()/dcd_int_disable() functions, which would collide in a dual-role build. +#if defined(TUP_USBIP_CHIPIDEA_FS_KINETIS) #include "fsl_device_registers.h" - #define KHCI USB0 + #define CI_FS_REG(_port) ((ci_fs_regs_t*) USB0_BASE) + #define CI_FS_IRQN USB0_IRQn #else #error "MCU is not supported" #endif -#include "host/hcd.h" -#include "host/usbh.h" +#define CI_REG CI_FS_REG(0) //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM DECLARATION //--------------------------------------------------------------------+ - -enum { - TOK_PID_OUT = 0x1u, - TOK_PID_IN = 0x9u, - TOK_PID_SETUP = 0xDu, - TOK_PID_DATA0 = 0x3u, - TOK_PID_DATA1 = 0xbu, - TOK_PID_ACK = 0x2u, - TOK_PID_STALL = 0xeu, - TOK_PID_NAK = 0xau, - TOK_PID_BUSTO = 0x0u, - TOK_PID_ERR = 0xfu, -}; - -typedef struct TU_ATTR_PACKED -{ - union { - uint32_t head; - struct { - union { - struct { - uint16_t : 2; - __IO uint16_t tok_pid : 4; - uint16_t data : 1; - __IO uint16_t own : 1; - uint16_t : 8; - }; - struct { - uint16_t : 2; - uint16_t bdt_stall : 1; - uint16_t dts : 1; - uint16_t ninc : 1; - uint16_t keep : 1; - uint16_t : 10; - }; - }; - __IO uint16_t bc : 10; - uint16_t : 6; - }; - }; - uint8_t *addr; -}buffer_descriptor_t; - -TU_VERIFY_STATIC( sizeof(buffer_descriptor_t) == 8, "size is not correct" ); +// TOK_PID_* and buffer_descriptor_t are shared with the device driver in ci_fs_type.h typedef struct TU_ATTR_PACKED { @@ -125,7 +72,10 @@ typedef struct union { /* [OUT,IN][EVEN,ODD] */ buffer_descriptor_t bdt[2][2]; - uint16_t bda[2*2]; + /* bda aliases bdt for STAT-register indexing: STAT gives the byte-offset/2 of the + * completed BD, so it indexes bda[] in uint16_t units. Each buffer_descriptor_t is + * 4 uint16_t, hence 2*2*4 elements to span the whole table (must equal sizeof bdt). */ + uint16_t bda[2*2*4]; }; endpoint_state_t endpoint[2]; pipe_state_t pipe[CFG_TUH_ENDPOINT_MAX * 2]; @@ -160,7 +110,9 @@ static int prepare_packets(int pipenum) endpoint_state_t *ep = &_hcd.endpoint[dir_tx]; unsigned const odd = ep->odd; buffer_descriptor_t *bd = _hcd.bdt[dir_tx]; - TU_ASSERT(0 == bd[odd].own, -1); + // The host shares a single BDT set across all pipes. If it is still owned by an + // in-flight transfer on another pipe, report busy so the caller can defer & retry. + if (bd[odd].own) return -1; // TU_LOG1(" %p dir %d odd %d data %d\r\n", &bd[odd], dir_tx, odd, pipe->data); @@ -218,11 +170,11 @@ static bool continue_transfer(int pipenum, buffer_descriptor_t *bd) bd->bc = next_rem > pipe->max_packet_size ? pipe->max_packet_size: next_rem; __DSB(); bd->own = 1; /* This bit must be set last */ - while (KHCI->CTL & USB_CTL_TXSUSPENDTOKENBUSY_MASK) ; - KHCI->TOKEN = KHCI->TOKEN; /* Queue the same token as the last */ + while (CI_REG->CTL & USB_CTL_TXSUSPENDTOKENBUSY_MASK) ; + CI_REG->TOKEN = CI_REG->TOKEN; /* Queue the same token as the last */ } else if (TUSB_DIR_IN == tu_edpt_dir(pipe->ep_addr)) { /* IN */ - while (KHCI->CTL & USB_CTL_TXSUSPENDTOKENBUSY_MASK) ; - KHCI->TOKEN = KHCI->TOKEN; + while (CI_REG->CTL & USB_CTL_TXSUSPENDTOKENBUSY_MASK) ; + CI_REG->TOKEN = CI_REG->TOKEN; } return true; } @@ -233,13 +185,21 @@ static bool continue_transfer(int pipenum, buffer_descriptor_t *bd) static bool resume_transfer(int pipenum) { int num_tokens = prepare_packets(pipenum); - TU_ASSERT(0 <= num_tokens); + if (num_tokens < 0) { + // Shared BDT still owned by an in-flight transfer on another pipe. Defer this + // pipe and retry on the next SOF once the BDT is free (avoids dropping the + // transfer, which stalls e.g. a 2nd device enumerating behind a hub while the + // app issues concurrent control transfers). + _hcd.pending |= TU_BIT(pipenum); + CI_REG->INT_EN |= USB_ISTAT_SOFTOK_MASK; + return true; + } - const unsigned ie = NVIC_GetEnableIRQ(USB0_IRQn); - NVIC_DisableIRQ(USB0_IRQn); + const unsigned ie = NVIC_GetEnableIRQ(CI_FS_IRQN); + NVIC_DisableIRQ(CI_FS_IRQN); pipe_state_t *pipe = &_hcd.pipe[pipenum]; - unsigned flags = KHCI->ENDPOINT[0].ENDPT & USB_ENDPT_HOSTWOHUB_MASK; + unsigned flags = CI_REG->EP[0].CTL & USB_ENDPT_HOSTWOHUB_MASK; flags |= USB_ENDPT_EPRXEN_MASK | USB_ENDPT_EPTXEN_MASK; switch (pipe->xfer) { case TUSB_XFER_CONTROL: @@ -254,16 +214,16 @@ static bool resume_transfer(int pipenum) } // TU_LOG1(" resume pipenum %d flags %x\r\n", pipenum, flags); - KHCI->ENDPOINT[0].ENDPT = flags; - KHCI->ADDR = (KHCI->ADDR & USB_ADDR_LSEN_MASK) | pipe->dev_addr; + CI_REG->EP[0].CTL = flags; + CI_REG->ADDR = (CI_REG->ADDR & USB_ADDR_LSEN_MASK) | pipe->dev_addr; unsigned const token = tu_edpt_number(pipe->ep_addr) | ((tu_edpt_dir(pipe->ep_addr) ? TOK_PID_IN: TOK_PID_OUT) << USB_TOKEN_TOKENPID_SHIFT); do { - while (KHCI->CTL & USB_CTL_TXSUSPENDTOKENBUSY_MASK) ; - KHCI->TOKEN = token; + while (CI_REG->CTL & USB_CTL_TXSUSPENDTOKENBUSY_MASK) ; + CI_REG->TOKEN = token; } while (--num_tokens); - if (ie) NVIC_EnableIRQ(USB0_IRQn); + if (ie) NVIC_EnableIRQ(CI_FS_IRQN); return true; } @@ -271,19 +231,38 @@ static void suspend_transfer(int pipenum, buffer_descriptor_t *bd) { pipe_state_t *pipe = &_hcd.pipe[pipenum]; pipe->buffer = bd->addr; - pipe->data = bd->data ^ 1; + // A NAK transfers no data, so the data toggle must be preserved for the retry. + // (Do NOT flip pipe->data here: flipping it makes the retried packet use the wrong + // DATA0/DATA1, which the device silently discards - breaking any bulk/interrupt + // transfer that is NAKed, e.g. the MSC CBW/CSW when the device is momentarily busy.) if ((TUSB_XFER_INTERRUPT == pipe->xfer) || (TUSB_XFER_BULK == pipe->xfer)) { _hcd.pending |= TU_BIT(pipenum); - KHCI->INTEN |= USB_ISTAT_SOFTOK_MASK; + CI_REG->INT_EN |= USB_ISTAT_SOFTOK_MASK; + } +} + +// Release the speculatively-armed sibling BDT of a multi-packet transfer. +// prepare_packets arms the sibling (odd^1) BDT (own=1) so a multi-packet transfer can +// ping-pong without NAKs. When the transfer ends - completes early on a short IN packet, +// stalls/errors, or (for IN) is NAKed before the sibling's token is issued - that sibling +// is left owned by the SIE. Because the host shares ONE BDT set across all pipes, a +// leftover armed sibling blocks every other pipe forever (e.g. a 2nd device stuck +// enumerating behind a hub). Release it - but ONLY for a multi-packet transfer: a +// single-packet transfer never armed a sibling, so that BDT slot may legitimately belong +// to another pipe's in-flight transfer. +static inline void release_sibling_bd(unsigned s, const pipe_state_t *pipe) +{ + if (pipe->length > pipe->max_packet_size) { + ((buffer_descriptor_t *)&_hcd.bda[s ^ USB_STAT_ODD_MASK])->own = 0; } } static void process_tokdne(uint8_t rhport) { (void)rhport; - const unsigned s = KHCI->STAT; - KHCI->ISTAT = USB_ISTAT_TOKDNE_MASK; /* fetch the next token if received */ + const unsigned s = CI_REG->STAT; + CI_REG->INT_STAT = USB_ISTAT_TOKDNE_MASK; /* fetch the next token if received */ uint8_t const dir_in = (s & USB_STAT_TX_MASK) ? TUSB_DIR_OUT: TUSB_DIR_IN; unsigned const odd = (s & USB_STAT_ODD_MASK) ? 1 : 0; @@ -313,6 +292,12 @@ static void process_tokdne(uint8_t rhport) result = XFER_RESULT_SUCCESS; break; case TOK_PID_NAK: + // Release the speculatively-armed sibling so the deferred retry (and any other pipe + // sharing the single BDT) can claim it; otherwise it stays own=1 forever and every + // same-direction transfer wedges. IN only: an IN issues just one token so the sibling + // was never put on the wire, whereas an OUT issues both tokens and its sibling may + // still be in flight - touching it there would race the SIE write-back. + if (TUSB_DIR_IN == dir_in) release_sibling_bd(s, &_hcd.pipe[pipenum]); suspend_transfer(pipenum, bd); next_pipenum = select_next_pipenum(pipenum); if (0 <= next_pipenum) @@ -328,8 +313,9 @@ static void process_tokdne(uint8_t rhport) } _hcd.in_progress &= ~TU_BIT(pipenum); pipe_state_t *pipe = &_hcd.pipe[ep->pipenum]; + release_sibling_bd(s, pipe); hcd_event_xfer_complete(pipe->dev_addr, - tu_edpt_addr(KHCI->TOKEN & USB_TOKEN_TOKENENDPT_MASK, dir_in), + tu_edpt_addr(CI_REG->TOKEN & USB_TOKEN_TOKENENDPT_MASK, dir_in), pipe->length - pipe->remaining, result, true); next_pipenum = select_next_pipenum(pipenum); @@ -339,29 +325,32 @@ static void process_tokdne(uint8_t rhport) static void process_attach(uint8_t rhport) { - unsigned ctl = KHCI->CTL; + unsigned ctl = CI_REG->CTL; if (!(ctl & USB_CTL_JSTATE_MASK)) { /* The attached device is a low speed device. */ - KHCI->ADDR = USB_ADDR_LSEN_MASK; - KHCI->ENDPOINT[0].ENDPT = USB_ENDPT_HOSTWOHUB_MASK; + CI_REG->ADDR = USB_ADDR_LSEN_MASK; + CI_REG->EP[0].CTL = USB_ENDPT_HOSTWOHUB_MASK; } hcd_event_device_attach(rhport, true); } static void process_bus_reset(uint8_t rhport) { - KHCI->ISTAT = USB_ISTAT_TOKDNE_MASK; - KHCI->USBCTRL &= ~USB_USBCTRL_SUSP_MASK; - KHCI->CTL &= ~USB_CTL_USBENSOFEN_MASK; - KHCI->ADDR = 0; - KHCI->ENDPOINT[0].ENDPT = 0; + CI_REG->INT_STAT = USB_ISTAT_TOKDNE_MASK; + CI_REG->USBCTRL &= ~USB_USBCTRL_SUSP_MASK; + CI_REG->CTL &= ~USB_CTL_USBENSOFEN_MASK; + CI_REG->ADDR = 0; + CI_REG->EP[0].CTL = 0; hcd_event_device_remove(rhport, true); _hcd.in_progress = 0; _hcd.pending = 0; + // Clear the ENTIRE shared BDT (both directions, both even/odd). Clearing only the IN + // pair left a stale OUT/SETUP descriptor (own=1) after a disconnect mid-OUT, which then + // blocks the first control transfer on re-enumeration. buffer_descriptor_t *bd = &_hcd.bdt[0][0]; - for (unsigned i = 0; i < 2; ++i, ++bd) { + for (unsigned i = 0; i < 2 * 2; ++i, ++bd) { bd->head = 0; } } @@ -372,31 +361,31 @@ static void process_bus_reset(uint8_t rhport) bool hcd_init(uint8_t rhport, const tusb_rhport_init_t* rh_init) { (void) rhport; (void) rh_init; - KHCI->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; - while (KHCI->USBTRC0 & USB_USBTRC0_USBRESET_MASK); + CI_REG->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; + while (CI_REG->USBTRC0 & USB_USBTRC0_USBRESET_MASK); tu_memclr(&_hcd, sizeof(_hcd)); - KHCI->USBTRC0 |= TU_BIT(6); /* software must set this bit to 1 */ - KHCI->BDTPAGE1 = (uint8_t)((uintptr_t)_hcd.bdt >> 8); - KHCI->BDTPAGE2 = (uint8_t)((uintptr_t)_hcd.bdt >> 16); - KHCI->BDTPAGE3 = (uint8_t)((uintptr_t)_hcd.bdt >> 24); + CI_REG->USBTRC0 |= TU_BIT(6); /* software must set this bit to 1 */ + CI_REG->BDT_PAGE1 = (uint8_t)((uintptr_t)_hcd.bdt >> 8); + CI_REG->BDT_PAGE2 = (uint8_t)((uintptr_t)_hcd.bdt >> 16); + CI_REG->BDT_PAGE3 = (uint8_t)((uintptr_t)_hcd.bdt >> 24); - KHCI->USBCTRL &= ~USB_USBCTRL_SUSP_MASK; - KHCI->CTL |= USB_CTL_ODDRST_MASK; + CI_REG->USBCTRL &= ~USB_USBCTRL_SUSP_MASK; + CI_REG->CTL |= USB_CTL_ODDRST_MASK; for (unsigned i = 0; i < 16; ++i) { - KHCI->ENDPOINT[i].ENDPT = 0; + CI_REG->EP[i].CTL = 0; } - KHCI->CTL &= ~USB_CTL_ODDRST_MASK; + CI_REG->CTL &= ~USB_CTL_ODDRST_MASK; - KHCI->SOFTHLD = 74; /* for 64-byte packets */ - // KHCI->SOFTHLD = 144; /* for low speed 8-byte packets */ - KHCI->CTL = USB_CTL_HOSTMODEEN_MASK | USB_CTL_SE0_MASK; - KHCI->USBCTRL = USB_USBCTRL_PDE_MASK; + CI_REG->SOF_THLD = 74; /* for 64-byte packets */ + // CI_REG->SOF_THLD = 144; /* for low speed 8-byte packets */ + CI_REG->CTL = USB_CTL_HOSTMODEEN_MASK | USB_CTL_SE0_MASK; + CI_REG->USBCTRL = USB_USBCTRL_PDE_MASK; - NVIC_ClearPendingIRQ(USB0_IRQn); - KHCI->INTEN = USB_INTEN_ATTACHEN_MASK | USB_INTEN_TOKDNEEN_MASK | + NVIC_ClearPendingIRQ(CI_FS_IRQN); + CI_REG->INT_EN = USB_INTEN_ATTACHEN_MASK | USB_INTEN_TOKDNEEN_MASK | USB_INTEN_USBRSTEN_MASK | USB_INTEN_ERROREN_MASK | USB_INTEN_STALLEN_MASK; - KHCI->ERREN = 0xff; + CI_REG->ERR_ENB = 0xff; return true; } @@ -404,13 +393,13 @@ bool hcd_init(uint8_t rhport, const tusb_rhport_init_t* rh_init) { void hcd_int_enable(uint8_t rhport) { (void)rhport; - NVIC_EnableIRQ(USB0_IRQn); + NVIC_EnableIRQ(CI_FS_IRQN); } void hcd_int_disable(uint8_t rhport) { (void)rhport; - NVIC_DisableIRQ(USB0_IRQn); + NVIC_DisableIRQ(CI_FS_IRQN); } uint32_t hcd_frame_number(uint8_t rhport) @@ -419,8 +408,8 @@ uint32_t hcd_frame_number(uint8_t rhport) /* The device must be reset at least once after connection * in order to start the frame counter. */ if (_hcd.need_reset) hcd_port_reset(rhport); - uint32_t frmnum = KHCI->FRMNUML; - frmnum |= KHCI->FRMNUMH << 8u; + uint32_t frmnum = CI_REG->FRM_NUML; + frmnum |= CI_REG->FRM_NUMH << 8u; return frmnum; } @@ -430,7 +419,7 @@ uint32_t hcd_frame_number(uint8_t rhport) bool hcd_port_connect_status(uint8_t rhport) { (void)rhport; - if (KHCI->ISTAT & USB_ISTAT_ATTACH_MASK) + if (CI_REG->INT_STAT & USB_ISTAT_ATTACH_MASK) return true; return false; } @@ -438,12 +427,12 @@ bool hcd_port_connect_status(uint8_t rhport) void hcd_port_reset(uint8_t rhport) { (void)rhport; - KHCI->CTL &= ~USB_CTL_USBENSOFEN_MASK; - KHCI->CTL |= USB_CTL_RESET_MASK; + CI_REG->CTL &= ~USB_CTL_USBENSOFEN_MASK; + CI_REG->CTL |= USB_CTL_RESET_MASK; unsigned cnt = SystemCoreClock / 100; while (cnt--) __NOP(); - KHCI->CTL &= ~USB_CTL_RESET_MASK; - KHCI->CTL |= USB_CTL_USBENSOFEN_MASK; + CI_REG->CTL &= ~USB_CTL_RESET_MASK; + CI_REG->CTL |= USB_CTL_USBENSOFEN_MASK; _hcd.need_reset = false; } @@ -455,26 +444,26 @@ tusb_speed_t hcd_port_speed_get(uint8_t rhport) { (void)rhport; tusb_speed_t speed = TUSB_SPEED_FULL; - const unsigned ie = NVIC_GetEnableIRQ(USB0_IRQn); - NVIC_DisableIRQ(USB0_IRQn); - if (KHCI->ADDR & USB_ADDR_LSEN_MASK) + const unsigned ie = NVIC_GetEnableIRQ(CI_FS_IRQN); + NVIC_DisableIRQ(CI_FS_IRQN); + if (CI_REG->ADDR & USB_ADDR_LSEN_MASK) speed = TUSB_SPEED_LOW; - if (ie) NVIC_EnableIRQ(USB0_IRQn); + if (ie) NVIC_EnableIRQ(CI_FS_IRQN); return speed; } void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { (void)rhport; - const unsigned ie = NVIC_GetEnableIRQ(USB0_IRQn); - NVIC_DisableIRQ(USB0_IRQn); + const unsigned ie = NVIC_GetEnableIRQ(CI_FS_IRQN); + NVIC_DisableIRQ(CI_FS_IRQN); pipe_state_t *p = &_hcd.pipe[0]; pipe_state_t *end = &_hcd.pipe[CFG_TUH_ENDPOINT_MAX * 2]; for (;p != end; ++p) { if (p->dev_addr == dev_addr) tu_memclr(p, sizeof(*p)); } - if (ie) NVIC_EnableIRQ(USB0_IRQn); + if (ie) NVIC_EnableIRQ(CI_FS_IRQN); } //--------------------------------------------------------------------+ @@ -501,12 +490,12 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet _hcd.in_progress |= TU_BIT(pipenum); - unsigned hostwohub = KHCI->ENDPOINT[0].ENDPT & USB_ENDPT_HOSTWOHUB_MASK; - KHCI->ENDPOINT[0].ENDPT = hostwohub | + unsigned hostwohub = CI_REG->EP[0].CTL & USB_ENDPT_HOSTWOHUB_MASK; + CI_REG->EP[0].CTL = hostwohub | USB_ENDPT_EPHSHK_MASK | USB_ENDPT_EPRXEN_MASK | USB_ENDPT_EPTXEN_MASK; - KHCI->ADDR = (KHCI->ADDR & USB_ADDR_LSEN_MASK) | dev_addr; - while (KHCI->CTL & USB_CTL_TXSUSPENDTOKENBUSY_MASK) ; - KHCI->TOKEN = (TOK_PID_SETUP << USB_TOKEN_TOKENPID_SHIFT); + CI_REG->ADDR = (CI_REG->ADDR & USB_ADDR_LSEN_MASK) | dev_addr; + while (CI_REG->CTL & USB_CTL_TXSUSPENDTOKENBUSY_MASK) ; + CI_REG->TOKEN = (TOK_PID_SETUP << USB_TOKEN_TOKENPID_SHIFT); return true; } @@ -558,16 +547,16 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * TU_ASSERT(0 <= pipenum); TU_ASSERT(0 == (_hcd.in_progress & TU_BIT(pipenum))); - unsigned const ie = NVIC_GetEnableIRQ(USB0_IRQn); - NVIC_DisableIRQ(USB0_IRQn); + unsigned const ie = NVIC_GetEnableIRQ(CI_FS_IRQN); + NVIC_DisableIRQ(CI_FS_IRQN); pipe_state_t *pipe = &_hcd.pipe[pipenum]; pipe->buffer = buffer; pipe->length = buflen; pipe->remaining = buflen; _hcd.in_progress |= TU_BIT(pipenum); _hcd.pending |= TU_BIT(pipenum); /* Send at the next Frame */ - KHCI->INTEN |= USB_ISTAT_SOFTOK_MASK; - if (ie) NVIC_EnableIRQ(USB0_IRQn); + CI_REG->INT_EN |= USB_ISTAT_SOFTOK_MASK; + if (ie) NVIC_EnableIRQ(CI_FS_IRQN); return true; } @@ -595,42 +584,42 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { void hcd_int_handler(uint8_t rhport, bool in_isr) { (void) in_isr; - uint32_t is = KHCI->ISTAT; - uint32_t msk = KHCI->INTEN; + uint32_t is = CI_REG->INT_STAT; + uint32_t msk = CI_REG->INT_EN; // TU_LOG1("S %lx\r\n", is); /* clear disabled interrupts */ - KHCI->ISTAT = (is & ~msk & ~USB_ISTAT_TOKDNE_MASK) | USB_ISTAT_SOFTOK_MASK; + CI_REG->INT_STAT = (is & ~msk & ~USB_ISTAT_TOKDNE_MASK) | USB_ISTAT_SOFTOK_MASK; is &= msk; if (is & USB_ISTAT_ERROR_MASK) { - unsigned err = KHCI->ERRSTAT; + unsigned err = CI_REG->ERR_STAT; if (err) { TU_LOG1(" ERR %x\r\n", err); - KHCI->ERRSTAT = err; + CI_REG->ERR_STAT = err; } else { - KHCI->INTEN &= ~USB_ISTAT_ERROR_MASK; + CI_REG->INT_EN &= ~USB_ISTAT_ERROR_MASK; } } if (is & USB_ISTAT_USBRST_MASK) { - KHCI->INTEN = (msk & ~USB_INTEN_USBRSTEN_MASK) | USB_INTEN_ATTACHEN_MASK; + CI_REG->INT_EN = (msk & ~USB_INTEN_USBRSTEN_MASK) | USB_INTEN_ATTACHEN_MASK; process_bus_reset(rhport); return; } if (is & USB_ISTAT_ATTACH_MASK) { - KHCI->INTEN = (msk & ~USB_INTEN_ATTACHEN_MASK) | USB_INTEN_USBRSTEN_MASK; + CI_REG->INT_EN = (msk & ~USB_INTEN_ATTACHEN_MASK) | USB_INTEN_USBRSTEN_MASK; _hcd.need_reset = true; process_attach(rhport); return; } if (is & USB_ISTAT_STALL_MASK) { - KHCI->ISTAT = USB_ISTAT_STALL_MASK; + CI_REG->INT_STAT = USB_ISTAT_STALL_MASK; } if (is & USB_ISTAT_SOFTOK_MASK) { msk &= ~USB_ISTAT_SOFTOK_MASK; - KHCI->INTEN = msk; + CI_REG->INT_EN = msk; if (_hcd.pending) { int pipenum = __builtin_ctz(_hcd.pending); _hcd.pending = 0; diff --git a/src/portable/chipidea/ci_hs/ci_hs_hpm.h b/src/portable/chipidea/ci_hs/ci_hs_hpm.h index 68211448c..327ffb2c4 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_hpm.h +++ b/src/portable/chipidea/ci_hs/ci_hs_hpm.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/chipidea/ci_hs/ci_hs_imxrt.h b/src/portable/chipidea/ci_hs/ci_hs_imxrt.h index 75d1d55b8..8f0d6083e 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_imxrt.h +++ b/src/portable/chipidea/ci_hs/ci_hs_imxrt.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -55,6 +36,9 @@ static const ci_hs_controller_t _ci_controller[] = #define CI_HS_REG(_port) ((ci_hs_regs_t*) _ci_controller[_port].reg_base) +// NXP recommends AHBBRST = INCR16 (remainder as unspecified-length bursts) +#define CI_HS_SET_AHB_BURST(_p) (CI_HS_REG(_p)->SBUSCFG = SBUSCFG_AHBBRST_INCR16_UNSPEC) + //------------- DCD -------------// #define CI_DCD_INT_ENABLE(_p) NVIC_EnableIRQ ((IRQn_Type)_ci_controller[_p].irqnum) #define CI_DCD_INT_DISABLE(_p) NVIC_DisableIRQ((IRQn_Type)_ci_controller[_p].irqnum) diff --git a/src/portable/chipidea/ci_hs/ci_hs_lpc18_43.h b/src/portable/chipidea/ci_hs/ci_hs_lpc18_43.h index c22aea887..c7dc7e69f 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_lpc18_43.h +++ b/src/portable/chipidea/ci_hs/ci_hs_lpc18_43.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -53,4 +34,9 @@ static const ci_hs_controller_t _ci_controller[] = #define CI_HCD_INT_ENABLE(_p) NVIC_EnableIRQ ((IRQn_Type)_ci_controller[_p].irqnum) #define CI_HCD_INT_DISABLE(_p) NVIC_DisableIRQ((IRQn_Type)_ci_controller[_p].irqnum) +// USB0 (high-speed) only: NXP recommends AHBBRST = INCR16 (remainder as +// unspecified-length bursts) +#define CI_HS_SET_AHB_BURST(_p) \ + do { if ((_p) == 0) { CI_HS_REG(_p)->SBUSCFG = SBUSCFG_AHBBRST_INCR16_UNSPEC; } } while (0) + #endif diff --git a/src/portable/chipidea/ci_hs/ci_hs_mcx.h b/src/portable/chipidea/ci_hs/ci_hs_mcx.h index f940f4a9d..ebf52de39 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_mcx.h +++ b/src/portable/chipidea/ci_hs/ci_hs_mcx.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/chipidea/ci_hs/ci_hs_rw61x.h b/src/portable/chipidea/ci_hs/ci_hs_rw61x.h index 114fe26c3..ddd08da6b 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_rw61x.h +++ b/src/portable/chipidea/ci_hs/ci_hs_rw61x.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/chipidea/ci_hs/ci_hs_type.h b/src/portable/chipidea/ci_hs/ci_hs_type.h index 2f3aa3694..b3ef3b6af 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_type.h +++ b/src/portable/chipidea/ci_hs/ci_hs_type.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -48,6 +29,14 @@ enum { USBCMD_INTR_THRESHOLD_MASK = 0x00FF0000u, // Interrupt Threshold bit 23:16 }; +// DEVICEADDR +#define DEVICEADDR_USBADR_POS 25 + +enum { + DEVICEADDR_USBADRA = TU_BIT(24), ///< Device Address Advance: stage USBADR until the next EP0 IN is ACKed + DEVICEADDR_USBADR_MASK = 0xFE000000u, ///< Device Address bit 31:25 +}; + // PORTSC1 #define PORTSC1_PORT_SPEED_POS 26 @@ -55,10 +44,18 @@ enum { PORTSC1_CURRENT_CONNECT_STATUS = TU_BIT(0), PORTSC1_FORCE_PORT_RESUME = TU_BIT(6), PORTSC1_SUSPEND = TU_BIT(7), + PORTSC1_PORT_RESET = TU_BIT(8), // read-only in device mode: a reset is being driven PORTSC1_FORCE_FULL_SPEED = TU_BIT(24), PORTSC1_PORT_SPEED = TU_BIT(26) | TU_BIT(27) }; +// PORTSC1 PSPD field values, once shifted down by PORTSC1_PORT_SPEED_POS. 3 is undefined. +enum { + PORTSC1_PORT_SPEED_FULL = 0, + PORTSC1_PORT_SPEED_LOW = 1, + PORTSC1_PORT_SPEED_HIGH = 2, +}; + // OTGSC enum { OTGSC_VBUS_DISCHARGE = TU_BIT(0), @@ -90,11 +87,18 @@ enum { USBMODE_VBUS_POWER_SELECT = TU_BIT(5), // Need to be enabled for LPC18XX/43XX in host mode }; +// SBUSCFG +enum { + SBUSCFG_AHBBRST_INCR16_UNSPEC = 7, // INCR16 burst, remainder as unspecified-length bursts +}; + // Device Registers typedef struct { //------------- ID + HW Parameter Registers-------------// - volatile uint32_t TU_RESERVED[64]; ///< For iMX RT10xx, but not used by LPC18XX/LPC43XX + volatile uint32_t TU_RESERVED[36]; ///< ID/HW parameter registers, not used by this driver + volatile uint32_t SBUSCFG; ///< System Bus Interface Configuration (not present on every MCU) + volatile uint32_t TU_RESERVED[27]; //------------- Capability Registers-------------// volatile uint8_t CAPLENGTH; ///< Capability Registers Length diff --git a/src/portable/chipidea/ci_hs/dcd_ci_hs.c b/src/portable/chipidea/ci_hs/dcd_ci_hs.c index 9ed75ffd9..f1c333280 100644 --- a/src/portable/chipidea/ci_hs/dcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/dcd_ci_hs.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -173,6 +154,14 @@ TU_VERIFY_STATIC(sizeof(dcd_qhd_t) == 64, "size is not correct"); #define QTD_NEXT_INVALID 0x01 +// Bounded spin for register waits. The longest legitimate wait is a flush held off by a packet +// already in progress: ~50 us for a full-speed 64-byte packet, a low thousands of dependent +// register reads, so healthy hardware never approaches this bound. Exceeding it means the +// controller has stopped responding, and the spin then only serves to keep an ISR (or an +// IRQ-masked caller) from hanging outright - the 3 ms reset-cleanup window of IMXRT1060RM 42.5.6.2.1 (p.2394) +// is already unreachable in that state, and the manual's remedy there is a controller reset. +#define CI_HS_BUSY_SPIN 10000u + typedef struct { // Must be at 2K alignment // Each endpoint with direction (IN/OUT) occupies a queue head @@ -183,6 +172,17 @@ typedef struct { CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(2048) static dcd_data_t _dcd_data; +// What the next Port Change Detect will be. Each one is preceded by the interrupt that causes it: +// a reset interrupt for the end of a bus reset - where the speed first becomes final - or a +// suspend interrupt for the resume that ends the suspend. A suspend itself raises no port change, +// which is why there is no such value here. Indexed by rhport, which is 0 or 1 on every ci_hs +// variant (NOT the controller count: mcx/rw61x map rhport 1 to controller 0). +enum { + PORT_CHANGE_REASON_RESET = 0, + PORT_CHANGE_REASON_RESUME = 1, +}; +static volatile uint8_t _port_change_reason[2]; + //--------------------------------------------------------------------+ // Prototypes and Helper Functions //--------------------------------------------------------------------+ @@ -191,12 +191,37 @@ TU_ATTR_ALWAYS_INLINE static inline uint8_t ci_ep_count(const ci_hs_regs_t *dcd_ return dcd_reg->DCCPARAMS & DCCPARAMS_DEN_MASK; } +static bool controller_reset(uint8_t rhport); + //--------------------------------------------------------------------+ // Controller API //--------------------------------------------------------------------+ -/// follows LPC43xx User Manual 23.10.3 -static void bus_reset(uint8_t rhport) { +// Flush endpoint buffers, following IMXRT1060RM 42.5.6.6.5 Flushing/De-priming an Endpoint +// (p.2413): write ENDPTFLUSH, wait for the controller +// to acknowledge, then confirm ENDPTSTAT went to zero. The controller refuses the flush when a +// packet is in progress, and the manual requires the procedure be repeated until it takes. +// Callers proceed regardless of the result; the bound only prevents an ISR-context hang on dead +// hardware. +static bool flush_endpoints(ci_hs_regs_t *dcd_reg, uint32_t mask) { + uint32_t guard = CI_HS_BUSY_SPIN; + do { + dcd_reg->ENDPTFLUSH = mask; + while (dcd_reg->ENDPTFLUSH & mask) { + if (!guard--) { + return false; + } + } + } while ((dcd_reg->ENDPTSTAT & mask) && guard--); + + return !(dcd_reg->ENDPTSTAT & mask); +} + +/// Everything the manual asks of the DCD when a reset is detected, in its order: clear the setup +/// and completion semaphores, cancel every prime, check the reset is still being driven, and free +/// the dTDs. All of it belongs inside the reset window (IMXRT1060RM 42.5.6.2.1, p.2394); nothing +/// is left for the port change that ends the reset, which only reports the negotiated speed. +static void bus_reset_begin(uint8_t rhport) { ci_hs_regs_t *dcd_reg = CI_HS_REG(rhport); // The reset value for all endpoint types is the control endpoint. If one endpoint @@ -212,17 +237,24 @@ static void bus_reset(uint8_t rhport) { //------------- Clear All Registers -------------// dcd_reg->ENDPTNAK = dcd_reg->ENDPTNAK; dcd_reg->ENDPTNAKEN = 0; - dcd_reg->USBSTS = dcd_reg->USBSTS; dcd_reg->ENDPTSETUPSTAT = dcd_reg->ENDPTSETUPSTAT; dcd_reg->ENDPTCOMPLETE = dcd_reg->ENDPTCOMPLETE; - while (dcd_reg->ENDPTPRIME) {} - dcd_reg->ENDPTFLUSH = 0xFFFFFFFF; - while (dcd_reg->ENDPTFLUSH) {} + uint32_t guard = CI_HS_BUSY_SPIN; + while (dcd_reg->ENDPTPRIME && guard--) {} + dcd_reg->ENDPTFLUSH = 0xFFFFFFFFUL; - // read reset bit in portsc + // All of the above must land while the reset is still being driven - it lasts at least 3 ms. + // Arriving late leaves the controller in an undefined state, and the manual's remedy is to + // hardware-reset it. That clears Run/Stop, so the device detaches and the host will drive a + // fresh reset and enumeration - which is why nothing below this point is worth doing here. + if (!(dcd_reg->PORTSC1 & PORTSC1_PORT_RESET)) { + TU_LOG1("ci_hs: reset cleanup ran past the end of the reset, resetting controller\r\n"); + controller_reset(rhport); + return; // the controller detached; the host's next reset redoes everything below + } - //------------- Queue Head & Queue TD -------------// + //------------- Free all allocated dTDs: the controller will not execute them again -------------// tu_memclr(&_dcd_data, sizeof(dcd_data_t)); //------------- Set up Control Endpoints (0 OUT, 1 IN) -------------// @@ -235,27 +267,29 @@ static void bus_reset(uint8_t rhport) { dcd_dcache_clean_invalidate(&_dcd_data, sizeof(dcd_data_t)); } -bool dcd_init(uint8_t rhport, const tusb_rhport_init_t *rh_init) { - (void)rh_init; - tu_memclr(&_dcd_data, sizeof(dcd_data_t)); - +/// Reset the controller and bring it back up in device mode. Also the manual's remedy when the +/// reset cleanup misses its window: the controller reset clears Run/Stop and detaches the device, +/// so it must be re-initialised completely afterwards (IMXRT1060RM 42.5.6.2.1, p.2394). +static bool controller_reset(uint8_t rhport) { ci_hs_regs_t *dcd_reg = CI_HS_REG(rhport); - TU_ASSERT(ci_ep_count(dcd_reg) <= TUP_DCD_ENDPOINT_MAX); - - #if TU_CHECK_MCU(OPT_MCU_HPM) - usb_phy_init((USB_Type *)dcd_reg, false); - #endif + tu_memclr(&_dcd_data, sizeof(dcd_data_t)); // Reset controller dcd_reg->USBCMD |= USBCMD_RESET; - while (dcd_reg->USBCMD & USBCMD_RESET) {} + uint32_t guard = CI_HS_BUSY_SPIN; + while ((dcd_reg->USBCMD & USBCMD_RESET) && guard--) {} + TU_VERIFY(!(dcd_reg->USBCMD & USBCMD_RESET)); // reached from the ISR too, so never halt here // Set mode to device, must be set immediately after reset uint32_t usbmode = dcd_reg->USBMODE & ~USBMOD_CM_MASK; usbmode |= USBMODE_CM_DEVICE; dcd_reg->USBMODE = usbmode; + #ifdef CI_HS_SET_AHB_BURST + CI_HS_SET_AHB_BURST(rhport); + #endif + #ifdef CFG_TUD_CI_HS_VBUS_CHARGE dcd_reg->OTGSC = OTGSC_VBUS_CHARGE | OTGSC_OTG_TERMINATION; #else @@ -272,9 +306,11 @@ bool dcd_init(uint8_t rhport, const tusb_rhport_init_t *rh_init) { dcd_dcache_clean_invalidate(&_dcd_data, sizeof(dcd_data_t)); + _port_change_reason[rhport] = PORT_CHANGE_REASON_RESET; + dcd_reg->ENDPTLISTADDR = (uint32_t)_dcd_data.qhd; // Endpoint List Address has to be 2K alignment dcd_reg->USBSTS = dcd_reg->USBSTS; - dcd_reg->USBINTR = INTR_USB | INTR_ERROR | INTR_PORT_CHANGE | INTR_SUSPEND; + dcd_reg->USBINTR = INTR_USB | INTR_ERROR | INTR_PORT_CHANGE | INTR_RESET | INTR_SUSPEND; uint32_t usbcmd = dcd_reg->USBCMD; usbcmd &= ~USBCMD_INTR_THRESHOLD_MASK; // Interrupt Threshold Interval = 0 @@ -285,8 +321,22 @@ bool dcd_init(uint8_t rhport, const tusb_rhport_init_t *rh_init) { return true; } +bool dcd_init(uint8_t rhport, const tusb_rhport_init_t *rh_init) { + (void)rh_init; + ci_hs_regs_t *dcd_reg = CI_HS_REG(rhport); + + TU_ASSERT(ci_ep_count(dcd_reg) <= TUP_DCD_ENDPOINT_MAX); + + #if TU_CHECK_MCU(OPT_MCU_HPM) + usb_phy_init((USB_Type *)dcd_reg, false); + #endif + + return controller_reset(rhport); +} + bool dcd_deinit(uint8_t rhport) { ci_hs_regs_t* dcd_reg = CI_HS_REG(rhport); + _port_change_reason[rhport] = PORT_CHANGE_REASON_RESET; // disable all interrupt dcd_reg->USBINTR = 0; @@ -295,9 +345,9 @@ bool dcd_deinit(uint8_t rhport) { dcd_reg->USBCMD &= ~USBCMD_RUN_STOP; // flush all endpoints - while (dcd_reg->ENDPTPRIME) {} - dcd_reg->ENDPTFLUSH = 0xFFFFFFFF; - while (dcd_reg->ENDPTFLUSH) {} + uint32_t guard = CI_HS_BUSY_SPIN; + while (dcd_reg->ENDPTPRIME && guard--) {} + flush_endpoints(dcd_reg, 0xFFFFFFFF); return true; } @@ -311,11 +361,18 @@ void dcd_int_disable(uint8_t rhport) { } void dcd_set_address(uint8_t rhport, uint8_t dev_addr) { - // Response with status first before changing device address - dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_IN), NULL, 0, false); + ci_hs_regs_t *dcd_reg = CI_HS_REG(rhport); + const uint32_t prev = dcd_reg->DEVICEADDR & DEVICEADDR_USBADR_MASK; - ci_hs_regs_t *dcd_reg = CI_HS_REG(rhport); - dcd_reg->DEVICEADDR = (dev_addr << 25) | TU_BIT(24); + // IMXRT1060RM 42.7.23 / UM10503 Table 478: stage the address before priming the status stage so + // hardware loads USBADR at the status ACK. Priming first races that ACK against this write. + dcd_reg->DEVICEADDR = ((uint32_t)dev_addr << DEVICEADDR_USBADR_POS) | DEVICEADDR_USBADRA; + + if (!dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_IN), NULL, 0, false)) { + // USB 2.0 9.4.6: the address changes only after the status stage completes successfully. The + // status never went out, so drop the stage - USBADRA=0 takes effect instantly. + dcd_reg->DEVICEADDR = prev; + } } void dcd_remote_wakeup(uint8_t rhport) { @@ -412,7 +469,8 @@ void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { ci_hs_regs_t *dcd_reg = CI_HS_REG(rhport); dcd_reg->ENDPTCTRL[epnum] |= ENDPTCTRL_STALL << (dir ? 16 : 0); - // flush to abort any primed buffer + // flush to abort any primed buffer; the aborted transfer's dQH overlay can be left + // ACTIVE with mid-transfer state - qhd_start_xfer clears it before the next prime dcd_reg->ENDPTFLUSH = TU_BIT(epnum + (dir ? 16 : 0)); } @@ -482,9 +540,7 @@ bool dcd_edpt_iso_activate(uint8_t rhport, const tusb_desc_endpoint_t *desc_ep) // dcd_dcache_clean_invalidate(&_dcd_data, sizeof(dcd_data_t)); // Flush EP - const uint32_t flush_mask = TU_BIT(epnum + (dir ? 16 : 0)); - dcd_reg->ENDPTFLUSH = flush_mask; - while (dcd_reg->ENDPTFLUSH & flush_mask) {} + flush_endpoints(dcd_reg, TU_BIT(epnum + (dir ? 16 : 0))); // disable to change max packet size ep_ctrl_clear(endptctrl, dir, ENDPTCTRL_ENABLE); @@ -510,25 +566,35 @@ void dcd_edpt_close_all(uint8_t rhport) { } } -static void qhd_start_xfer(uint8_t rhport, uint8_t epnum, uint8_t dir) { +static bool qhd_start_xfer(uint8_t rhport, uint8_t epnum, uint8_t dir) { ci_hs_regs_t *dcd_reg = CI_HS_REG(rhport); dcd_qhd_t *p_qhd = &_dcd_data.qhd[epnum][dir]; dcd_qtd_t *p_qtd = &_dcd_data.qtd[epnum][dir]; p_qhd->qtd_overlay.halted = false; // clear any previous error + p_qhd->qtd_overlay.active = false; // a flushed prime leaves stale ACTIVE state; clear it so the fresh qtd loads p_qhd->qtd_overlay.next = (uint32_t)p_qtd; // link qtd to qhd // flush cache dcd_dcache_clean_invalidate(&_dcd_data, sizeof(dcd_data_t)); if (epnum == 0) { - // follows UM 24.10.8.1.1 Setup packet handling using setup lockout mechanism - // wait until ENDPTSETUPSTAT before priming data/status in response TODO add time out - while (dcd_reg->ENDPTSETUPSTAT & TU_BIT(0)) {} + // Setup lockout (IMXRT1060RM 42.5.6.4.2.1 Setup Phase, p.2403): never prime EP0 while a new + // SETUP is pending. The ISR + // normally consumes ENDPTSETUPSTAT quickly; if the guard trips, fail the transfer so usbd + // releases the endpoint (a pending SETUP supersedes this response anyway; without one, usbd + // stalls EP0 and the host recovers with a fresh control transfer). + uint32_t guard = CI_HS_BUSY_SPIN; + while (dcd_reg->ENDPTSETUPSTAT & TU_BIT(0)) { + if (!guard--) { + return false; + } + } } // start transfer dcd_reg->ENDPTPRIME = TU_BIT(epnum + (dir ? 16 : 0)); + return true; } bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t *buffer, uint16_t total_bytes, bool is_isr) { @@ -544,9 +610,7 @@ bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t *buffer, uint16_t to // Start qhd transfer p_qhd->ff = NULL; - qhd_start_xfer(rhport, epnum, dir); - - return true; + return qhd_start_xfer(rhport, epnum, dir); } #if !CFG_TUD_MEM_DCACHE_ENABLE @@ -597,9 +661,7 @@ bool dcd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t *ff, uint16_t // Start qhd transfer p_qhd->ff = ff; - qhd_start_xfer(rhport, epnum, dir); - - return true; + return qhd_start_xfer(rhport, epnum, dir); } #endif @@ -647,43 +709,43 @@ void dcd_int_handler(uint8_t rhport) { return; } - // Set if the port controller enters the full or high-speed operational state. - // either from Bus Reset or Suspended state - if (int_status & INTR_PORT_CHANGE) { - // TU_LOG2("PortChange %08lx\r\n", dcd_reg->PORTSC1); - - // Reset interrupt is not enabled, we manually check if Port Change is due - // to connection / disconnection - if (dcd_reg->USBSTS & INTR_RESET) { - dcd_reg->USBSTS = INTR_RESET; + const uint8_t pci_reason = _port_change_reason[rhport]; // save current pci_reason - if (dcd_reg->PORTSC1 & PORTSC1_CURRENT_CONNECT_STATUS) { - const uint32_t speed = (dcd_reg->PORTSC1 & PORTSC1_PORT_SPEED) >> PORTSC1_PORT_SPEED_POS; - bus_reset(rhport); - dcd_event_bus_reset(rhport, (tusb_speed_t)speed, true); - } else { - dcd_event_bus_signal(rhport, DCD_EVENT_UNPLUGGED, true); - } - } else { - // Triggered by resuming from suspended state - if (!(dcd_reg->PORTSC1 & PORTSC1_SUSPEND)) { - dcd_event_bus_signal(rhport, DCD_EVENT_RESUME, true); - } - } + if (int_status & INTR_SUSPEND) { + _port_change_reason[rhport] = PORT_CHANGE_REASON_RESUME; // next PCI is resume + dcd_event_bus_signal(rhport, DCD_EVENT_SUSPEND, true); } - if (int_status & INTR_SUSPEND) { - // TU_LOG2("Suspend %08lx\r\n", dcd_reg->PORTSC1); + // USB Reset Received: register cleanup runs here within the reset window (IMXRT1060RM 42.5.6.2.1, p.2394) + // and BUS_RESET_START fires now; BUS_RESET_END, with the final speed, is triggered later by PCI. + if (int_status & INTR_RESET) { + _port_change_reason[rhport] = PORT_CHANGE_REASON_RESET; + bus_reset_begin(rhport); + dcd_event_bus_signal(rhport, DCD_EVENT_BUS_RESET_START, true); + } - if (dcd_reg->PORTSC1 & PORTSC1_SUSPEND) { - // Note: Host may delay more than 3 ms before and/or after bus reset before doing enumeration. - // Skip suspend event if we are not addressed - if ((dcd_reg->DEVICEADDR >> 25) & 0x0f) { - dcd_event_bus_signal(rhport, DCD_EVENT_SUSPEND, true); - } + // Port entered the full/high-speed operational state: the end of a bus reset, or a resume. + if (int_status & INTR_PORT_CHANGE) { + if (pci_reason == PORT_CHANGE_REASON_RESUME) { + dcd_event_bus_signal(rhport, DCD_EVENT_RESUME, true); + } else { + // the undefined encoding falls back to full speed + const uint32_t pspd = (dcd_reg->PORTSC1 & PORTSC1_PORT_SPEED) >> PORTSC1_PORT_SPEED_POS; + const tusb_speed_t speed = (pspd == PORTSC1_PORT_SPEED_LOW) ? TUSB_SPEED_LOW : + (pspd == PORTSC1_PORT_SPEED_HIGH) ? TUSB_SPEED_HIGH : TUSB_SPEED_FULL; + dcd_event_bus_reset(rhport, speed, true); + // This reset is over, so the next port change is a resume. Leaving it at RESET instead would + // dispatch every later resume as another end-of-reset, clearing the queue heads mid-session. + _port_change_reason[rhport] = PORT_CHANGE_REASON_RESUME; } } + // No unplug detection yet, by the manual rather than by omission: IMXRT1060RM 42.7.31 (p.2470) says a zero + // Current Connect Status means the device "did not attach successfully or was forcibly + // disconnected by the software writing a zero to the Run bit ... It does not state the device + // being disconnected or suspended", so a cable pull raises no port change at all. VBUS via + // OTGSC BSV is the manual's disconnect indicator, and it is board dependent. + if (int_status & INTR_USB) { // Make sure we read the latest version of _dcd_data. dcd_dcache_clean_invalidate(&_dcd_data, sizeof(dcd_data_t)); @@ -691,7 +753,7 @@ void dcd_int_handler(uint8_t rhport) { const uint32_t edpt_complete = dcd_reg->ENDPTCOMPLETE; dcd_reg->ENDPTCOMPLETE = edpt_complete; // acknowledge - // 23.10.12.3 Failed QTD also get ENDPTCOMPLETE set + // 42.5.6.6.4 Transfer Completion (p.2413): a failed dTD also sets ENDPTCOMPLETE // nothing to do, we will submit xfer as error to usbd // if (int_status & INTR_ERROR) { } @@ -707,12 +769,39 @@ void dcd_int_handler(uint8_t rhport) { } // Set up Received - // 23.10.10.2 Operational model for setup transfers + // 42.5.6.4.2 Control Endpoint Operation Model (p.2403) // Must be after normal transfer complete since it is possible to have both previous control status + new setup // in the same frame and we should handle previous status first. if (dcd_reg->ENDPTSETUPSTAT) { + // 42.5.6.4.2.1 Setup Phase (p.2403) steps 1-2: duplicate the setup payload BEFORE clearing + // ENDPTSETUPSTAT - + // the clear releases the setup lockout and a back-to-back SETUP (usbtest case 10) can + // overwrite the queue-head buffer immediately after. The copy is read through the volatile + // qualifier rather than memcpy'd because C orders volatile accesses only against each + // other: a plain copy may legally be sunk past the lockout-releasing store below. + union { + tusb_control_request_t request; + uint8_t byte[8]; + } setup; + const volatile uint8_t *setup_src = (const volatile uint8_t *)&_dcd_data.qhd[0][0].setup_request; + for (uint8_t i = 0; i < sizeof(setup.request); i++) { + setup.byte[i] = setup_src[i]; + } dcd_reg->ENDPTSETUPSTAT = dcd_reg->ENDPTSETUPSTAT; - dcd_event_setup_received(rhport, (uint8_t *)(uintptr_t)&_dcd_data.qhd[0][0].setup_request, true); + + // Retire a status/handshake phase left primed by the previous control sequence + // (IMXRT1060RM 42.5.6.4.2.1, p.2403), which would otherwise retire the response the task is about to + // prime for this setup. Skipped when EP0 has nothing primed or priming, since the manual + // does not want the flush wait in an interrupt handler when it has nothing to do. + // One volatile read per statement: C leaves their order unspecified within a single + // expression, which IAR rejects outright (Pa082). + const uint32_t ep0_mask = TU_BIT(0) | TU_BIT(16); + const uint32_t ep0_stat = dcd_reg->ENDPTSTAT; + const uint32_t ep0_prime = dcd_reg->ENDPTPRIME; + if ((ep0_stat | ep0_prime) & ep0_mask) { + flush_endpoints(dcd_reg, ep0_mask); + } + dcd_event_setup_received(rhport, setup.byte, true); } } diff --git a/src/portable/chipidea/ci_hs/hcd_ci_hs.c b/src/portable/chipidea/ci_hs/hcd_ci_hs.c index c0d14fe57..0f24f5bb6 100644 --- a/src/portable/chipidea/ci_hs/hcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/hcd_ci_hs.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -101,6 +82,10 @@ bool hcd_init(uint8_t rhport, const tusb_rhport_init_t *rh_init) { hcd_reg->USBMODE = USBMODE_CM_HOST; #endif + #ifdef CI_HS_SET_AHB_BURST + CI_HS_SET_AHB_BURST(rhport); + #endif + #if !TUH_OPT_HIGH_SPEED hcd_reg->PORTSC1 |= PORTSC1_FORCE_FULL_SPEED; #endif diff --git a/src/portable/dialog/da146xx/dcd_da146xx.c b/src/portable/dialog/da146xx/dcd_da146xx.c index 7d90b1f94..dc662857e 100644 --- a/src/portable/dialog/da146xx/dcd_da146xx.c +++ b/src/portable/dialog/da146xx/dcd_da146xx.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2020 Jerzy Kasenberg - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2020 Jerzy Kasenberg + * SPDX-FileCopyrightText: Copyright (c) 2020 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 03c3b91fd..660c38d8f 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/ehci/ehci.h b/src/portable/ehci/ehci.h index 719bdeafc..9d86ed04f 100644 --- a/src/portable/ehci/ehci.h +++ b/src/portable/ehci/ehci.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/ehci/ehci_api.h b/src/portable/ehci/ehci_api.h index e9018639f..6e3ddfb66 100644 --- a/src/portable/ehci/ehci_api.h +++ b/src/portable/ehci/ehci_api.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/mentor/musb/dcd_musb.c b/src/portable/mentor/musb/dcd_musb.c index 1d1280bf4..92c9fe92e 100644 --- a/src/portable/mentor/musb/dcd_musb.c +++ b/src/portable/mentor/musb/dcd_musb.c @@ -1,26 +1,8 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021 Koji KITAYAMA - * Copyright (c) 2024, Brent Kowal (Analog Devices, Inc) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021 Koji Kitayama + * SPDX-FileCopyrightText: Copyright (c) 2024, Brent Kowal (Analog Devices, Inc) + * SPDX-FileCopyrightText: Copyright (c) 2021 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -42,6 +24,8 @@ #include "musb_ti.h" #elif defined(TUP_USBIP_MUSB_ADI) #include "musb_max32.h" +#elif defined(TUP_USBIP_MUSB_PY32) + #include "musb_py32.h" #else #error "Unsupported MCU" #endif @@ -63,6 +47,7 @@ typedef struct { }; uint16_t length; /* the number of bytes in the buffer */ uint16_t remaining; /* the number of bytes remaining in the buffer */ + uint16_t mps; /* maximum packet size */ bool armed; /* true while a transfer is posted */ bool use_fifo; /* true: buf is tu_fifo_t*; false: buf is plain byte pointer. */ } pipe_state_t; @@ -177,6 +162,14 @@ TU_ATTR_ALWAYS_INLINE static inline pipe_state_t* pipe_get(uint8_t epnum, tusb_d return &_dcd.pipe[idx]; } +TU_ATTR_ALWAYS_INLINE static inline uint16_t musb_mps_to_maxp(uint16_t mps) { +#if defined(TUP_USBIP_MUSB_PY32) + return (uint8_t) ((mps + 7u) / 8u); +#else + return mps; +#endif +} + //-------------------------------------------------------------------- // HW FIFO Helper // Note: Index register is already set by caller @@ -241,7 +234,12 @@ TU_ATTR_ALWAYS_INLINE static inline bool hwfifo_config(musb_regs_t* musb, unsign bool double_packet) { (void) mps; - #if defined(TUP_USBIP_MUSB_ADI) + #if defined(TUP_USBIP_MUSB_PY32) + (void) musb; (void) is_rx; (void) double_packet; + // Puya FIFO sizes: EP0 = 64 B, EP1 = 512 B, EP2..4 = 128 B, EP5 = 64 B, shared between IN and OUT. + static const uint16_t py32_fifo_size[] = { 64, 512, 128, 128, 128, 64 }; + return epnum < TU_ARRAY_SIZE(py32_fifo_size) && mps <= py32_fifo_size[epnum]; + #elif defined(TUP_USBIP_MUSB_ADI) // AnalogDevice FIFO sizes: EP1..7 = 512 B, EP8..9 = 2048 B, EP10..11 = 4096 B. // DPB requires FIFO >= 2 * MPS. For HS bulk (MPS=512) only EP >= 8 qualifies. // Force single-buffered on EP < 8 even if the caller requested DPB. @@ -284,7 +282,7 @@ TU_ATTR_ALWAYS_INLINE static inline void hwfifo_flush(musb_regs_t* musb, unsigne // write to txfifo using pipe_state_t info static void pipe_write(musb_regs_t* musb_regs, pipe_state_t* pipe, uint8_t epnum) { musb_ep_csr_t* ep_csr = &musb_regs->indexed_csr; - const uint16_t mps = ep_csr->tx_maxp & MUSB_TXMAXP_PACKET_SIZE_M; + const uint16_t mps = pipe->mps; const uint16_t xact_len = tu_min16(mps, pipe->remaining); volatile void *hwfifo = &musb_regs->fifo[epnum]; if (xact_len) { @@ -310,6 +308,12 @@ static void process_epin_isr(uint8_t rhport, musb_regs_t *musb_regs, uint8_t epn } pipe_state_t* pipe = pipe_get(epnum, TUSB_DIR_IN); + // No active transfer: a halt/abort disarmed the pipe (armed=false) but may leave remaining>0. + // Do not keep loading the aborted transfer — that would re-fill the just-flushed FIFO and the + // next (re-armed) transfer's data would stack on top (host sees an oversized packet -> babble). + if (!pipe->armed) { + return; + } if (pipe->remaining > 0) { pipe_write(musb_regs, pipe, epnum); } else { @@ -332,7 +336,7 @@ static void process_epin_isr(uint8_t rhport, musb_regs_t *musb_regs, uint8_t epn // release the FIFO slot by clearing RXRDY. return true if short packet static bool pipe_read(musb_regs_t* musb_regs, pipe_state_t* pipe, uint8_t epnum) { musb_ep_csr_t* ep_csr = &musb_regs->indexed_csr; // index already set in process_epout_isr() - const uint16_t mps = ep_csr->rx_maxp & MUSB_RXMAXP_PACKET_SIZE_M; + const uint16_t mps = pipe->mps; const uint16_t rx_count = ep_csr->rx_count; const uint16_t xact_len = tu_min16(tu_min16(pipe->remaining, mps), rx_count); volatile void *hwfifo = &musb_regs->fifo[epnum]; @@ -644,7 +648,11 @@ static void process_bus_reset_isr(uint8_t rhport) { hwfifo_reset(musb, i, 0); hwfifo_reset(musb, i, 1); } +#if defined(TUP_USBIP_MUSB_PY32) + dcd_event_bus_reset(rhport, TUSB_SPEED_FULL, true); +#else dcd_event_bus_reset(rhport, (musb->power & MUSB_POWER_HSMODE) ? TUSB_SPEED_HIGH : TUSB_SPEED_FULL, true); +#endif } /*------------------------------------------------------------------ @@ -653,6 +661,11 @@ static void process_bus_reset_isr(uint8_t rhport) { #if CFG_TUSB_DEBUG >= MUSB_DEBUG static void print_musb_info(musb_regs_t* musb_regs) { +#if defined(TUP_USBIP_MUSB_PY32) + (void) musb_regs; + // musb discovery fields not present + TU_LOG1("musb py32 fixed full-speed configuration\r\n"); +#else // print version, epinfo, raminfo, config_data0, fifo_size TU_LOG1("musb version = %u.%u\r\n", musb_regs->hwvers_bit.major, musb_regs->hwvers_bit.minor); TU_LOG1("Number of endpoints: %u TX, %u RX\r\n", musb_regs->epinfo_bit.tx_ep_num, musb_regs->epinfo_bit.rx_ep_num); @@ -669,6 +682,7 @@ static void print_musb_info(musb_regs_t* musb_regs) { TU_LOG1("FIFO %u Size: TX %u RX %u\r\n", i, musb_regs->indexed_csr.fifo_size_bit.tx, musb_regs->indexed_csr.fifo_size_bit.rx); } #endif +#endif } #endif @@ -724,6 +738,18 @@ void dcd_remote_wakeup(uint8_t rhport) { musb_regs->power &= ~MUSB_POWER_RESUME; } +#if defined(TUP_USBIP_MUSB_PY32) +void dcd_connect(uint8_t rhport) +{ + (void) rhport; +} + +void dcd_disconnect(uint8_t rhport) +{ + (void) rhport; +} +#else + // Connect by enabling internal pull-up resistor on D+/D- void dcd_connect(uint8_t rhport) { @@ -739,6 +765,8 @@ void dcd_disconnect(uint8_t rhport) musb_regs->power &= ~MUSB_POWER_SOFTCONN; } +#endif + void dcd_sof_enable(uint8_t rhport, bool en) { (void) rhport; @@ -762,6 +790,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) { pipe->buf = NULL; pipe->length = 0; pipe->remaining = 0; + pipe->mps = (uint16_t) mps; pipe->armed = false; musb_regs_t* musb = MUSB_REGS(rhport); @@ -769,7 +798,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) { const uint8_t is_rx = (1 - epdir); musb_ep_maxp_csr_t* maxp_csr = &ep_csr->maxp_csr[is_rx]; - maxp_csr->maxp = mps; + maxp_csr->maxp = musb_mps_to_maxp((uint16_t) mps); maxp_csr->csrh = 0; #if MUSB_CFG_SHARED_FIFO if (epdir) { @@ -780,7 +809,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) { hwfifo_flush(musb, epn, is_rx, true); TU_ASSERT(hwfifo_config(musb, epn, is_rx, mps, ep_desc->bmAttributes.xfer == TUSB_XFER_BULK)); - musb->intren_ep[is_rx] |= TU_BIT(epn); + musb->intren_ep[is_rx ^ MUSB_INTR_EP_TX_RX_SWAP] |= TU_BIT(epn); return true; } @@ -791,8 +820,11 @@ bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet musb_regs_t* musb = MUSB_REGS(rhport); musb_ep_csr_t* ep_csr = get_ep_csr(musb, epn); const uint8_t is_rx = 1 - dir_in; + pipe_state_t *pipe = pipe_get(epn, dir_in); + pipe->mps = largest_packet_size; ep_csr->maxp_csr[is_rx].csrh = 0; - return hwfifo_config(musb, epn, is_rx, largest_packet_size, true); + TU_ASSERT(hwfifo_config(musb, epn, is_rx, largest_packet_size, true)); + return true; } bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const *ep_desc ) { @@ -808,6 +840,7 @@ bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const *ep_desc ) pipe->buf = NULL; pipe->length = 0; pipe->remaining = 0; + pipe->mps = (uint16_t) mps; pipe->armed = false; musb_regs_t* musb = MUSB_REGS(rhport); @@ -815,7 +848,7 @@ bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const *ep_desc ) const uint8_t is_rx = 1 - dir_in; musb_ep_maxp_csr_t* maxp_csr = &ep_csr->maxp_csr[is_rx]; - maxp_csr->maxp = mps; + maxp_csr->maxp = musb_mps_to_maxp((uint16_t) mps); maxp_csr->csrh |= MUSB_CSRH_ISO; #if MUSB_CFG_SHARED_FIFO if (dir_in) { @@ -830,7 +863,7 @@ bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const *ep_desc ) musb->fifo_size[is_rx] = hwfifo_byte2size(mps) | MUSB_FIFOSZ_DOUBLE_PACKET; #endif - musb->intren_ep[is_rx] |= TU_BIT(epn); + musb->intren_ep[is_rx ^ MUSB_INTR_EP_TX_RX_SWAP] |= TU_BIT(epn); if (ie) musb_dcd_int_enable(rhport); @@ -851,7 +884,7 @@ void dcd_edpt_close_all(uint8_t rhport) musb_ep_maxp_csr_t* maxp_csr = &ep_csr->maxp_csr[d]; hwfifo_flush(musb, i, d, true); hwfifo_reset(musb, i, d); - maxp_csr->maxp = 0; + maxp_csr->maxp = musb_mps_to_maxp(0); maxp_csr->csrh = 0; } } @@ -928,6 +961,10 @@ void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { } else { const tusb_dir_t ep_dir = tu_edpt_dir(ep_addr); const uint8_t is_rx = (ep_dir == TUSB_DIR_OUT ? 1u : 0u); + // A halt aborts the transfer: flush staged FIFO packet(s) before stalling, else leftover TX data + // concatenates with the next transfer after un-halt -> host sees an oversized packet (babble). + // FLUSH must precede SEND_STALL, which clears the TXRDY that hwfifo_flush() gates on. + hwfifo_flush(musb_regs, epn, is_rx, false); ep_csr->maxp_csr[is_rx].csrl = MUSB_CSRL_SEND_STALL(is_rx); pipe_state_t* pipe = pipe_get(epn, ep_dir); pipe->armed = false; diff --git a/src/portable/mentor/musb/hcd_musb.c b/src/portable/mentor/musb/hcd_musb.c index dcc023e0b..6a1601963 100644 --- a/src/portable/mentor/musb/hcd_musb.c +++ b/src/portable/mentor/musb/hcd_musb.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021 Koji KITAYAMA - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021 Koji Kitayama + * SPDX-FileCopyrightText: Copyright (c) 2021 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/mentor/musb/musb_max32.h b/src/portable/mentor/musb/musb_max32.h index 134b47122..9cf99126e 100644 --- a/src/portable/mentor/musb/musb_max32.h +++ b/src/portable/mentor/musb/musb_max32.h @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024, Brent Kowal (Analog Devices, Inc) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024, Brent Kowal (Analog Devices, Inc) + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -46,6 +28,7 @@ extern "C" { #define MUSB_CFG_SHARED_FIFO 1 // shared FIFO for TX and RX endpoints #define MUSB_CFG_DYNAMIC_FIFO 0 // dynamic EP FIFO sizing +#define MUSB_INTR_EP_TX_RX_SWAP 0 static const uintptr_t MUSB_BASES[] = { MXC_BASE_USBHS }; diff --git a/src/portable/mentor/musb/musb_py32.h b/src/portable/mentor/musb/musb_py32.h new file mode 100644 index 000000000..68d58ccb8 --- /dev/null +++ b/src/portable/mentor/musb/musb_py32.h @@ -0,0 +1,79 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2026, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef TUSB_MUSB_PY32_H_ +#define TUSB_MUSB_PY32_H_ + +#include "py32f0xx.h" + +#ifdef __cplusplus +extern "C" { +#endif + +// PY32 does not expose generic MUSB shared FIFO allocation registers; this +// selects the existing TX_MODE path required for IN endpoints. +#define MUSB_CFG_SHARED_FIFO 1 +#define MUSB_CFG_DYNAMIC_FIFO 0 +#define MUSB_INTR_EP_TX_RX_SWAP 1 + +static const uintptr_t MUSB_BASES[] = { USBD_BASE }; +static const IRQn_Type musb_irqs[] = { USB_IRQn }; + +TU_ATTR_ALWAYS_INLINE static inline void musb_dcd_phy_init(uint8_t rhport) { + musb_regs_t* musb_regs = MUSB_REGS(rhport); + + musb_regs->index = 0; + musb_regs->faddr = 0; + musb_regs->intr_usben = MUSB_IE_RESET | MUSB_IE_RESUME | MUSB_IE_SUSPND; + musb_regs->intr_txen = TU_BIT(0); + musb_regs->intr_rxen = 0; +} + +TU_ATTR_ALWAYS_INLINE static inline void musb_dcd_int_enable(uint8_t rhport) { + NVIC_EnableIRQ(musb_irqs[rhport]); +} + +TU_ATTR_ALWAYS_INLINE static inline void musb_dcd_int_disable(uint8_t rhport) { + NVIC_DisableIRQ(musb_irqs[rhport]); +} + +TU_ATTR_ALWAYS_INLINE static inline void musb_dcd_int_clear(uint8_t rhport) { + NVIC_ClearPendingIRQ(musb_irqs[rhport]); +} + +TU_ATTR_ALWAYS_INLINE static inline unsigned musb_dcd_get_int_enable(uint8_t rhport) { + return NVIC_GetEnableIRQ(musb_irqs[rhport]); +} + +TU_ATTR_ALWAYS_INLINE static inline void musb_dcd_int_handler_enter(uint8_t rhport) { + (void) rhport; +} + +#ifdef __cplusplus +} +#endif + +#endif diff --git a/src/portable/mentor/musb/musb_ti.h b/src/portable/mentor/musb/musb_ti.h index deaea8017..1cf26b1cb 100644 --- a/src/portable/mentor/musb/musb_ti.h +++ b/src/portable/mentor/musb/musb_ti.h @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024, Brent Kowal (Analog Devices, Inc) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024, Brent Kowal (Analog Devices, Inc) + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -48,6 +30,7 @@ #define MUSB_CFG_SHARED_FIFO 0 #define MUSB_CFG_DYNAMIC_FIFO 1 #define MUSB_CFG_DYNAMIC_FIFO_SIZE 4096 +#define MUSB_INTR_EP_TX_RX_SWAP 0 static const uintptr_t MUSB_BASES[] = { USB0_BASE }; diff --git a/src/portable/mentor/musb/musb_type.h b/src/portable/mentor/musb/musb_type.h index 3d3c3c834..1e8a761c0 100644 --- a/src/portable/mentor/musb/musb_type.h +++ b/src/portable/mentor/musb/musb_type.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -83,6 +64,75 @@ #define __R volatile const #endif +#if defined(TUP_USBIP_MUSB_PY32) + +typedef struct TU_ATTR_PACKED { + __IO uint8_t csrh; // 0x04, 0x08: CSRH + __IO uint8_t csrl; // 0x05, 0x09: CSRL + __IO uint8_t maxp; // 0x06, 0x0A: MAXP + __I uint8_t reserved; +} musb_ep_maxp_csr_t; + +TU_VERIFY_STATIC(sizeof(musb_ep_maxp_csr_t) == 4, "size is not correct"); + +typedef struct TU_ATTR_PACKED { + __IO uint8_t csr0l; // 0x00: CSR0 + __IO uint8_t count0; // 0x01: COUNT0 + __I uint8_t reserved_0x02[2]; + + union { + struct { + __IO uint8_t tx_csrh; // 0x04: TX CSRH + __IO uint8_t tx_csrl; // 0x05: TX CSRL + __IO uint8_t tx_maxp; // 0x06: TX MAXP + __I uint8_t reserved_0x07; + + __IO uint8_t rx_csrh; // 0x08: RX CSRH + __IO uint8_t rx_csrl; // 0x09: RX CSRL + __IO uint8_t rx_maxp; // 0x0A: RX MAXP + __I uint8_t reserved_0x0b; + }; + + musb_ep_maxp_csr_t maxp_csr[2]; + }; + + __IO uint16_t rx_count; // 0x0C: RX COUNT + __I uint8_t reserved_0x0e[2]; +} musb_ep_csr_t; + +TU_VERIFY_STATIC(sizeof(musb_ep_csr_t) == 16, "size is not correct"); + +typedef struct TU_ATTR_PACKED { + __IO uint8_t faddr; // 0x00: FADDR + __IO uint8_t power; // 0x01: POWER + __I uint8_t reserved_0x02[2]; + + __IO uint8_t intr_usb; // 0x04: INTRUSB + __IO uint8_t intr_rx; // 0x05: INTRRX + __IO uint8_t intr_tx; // 0x06: INTRTX + __I uint8_t reserved_0x07; + + __IO uint8_t intr_usben; // 0x08: INTRUSBEN + union { + struct { + __IO uint8_t intr_rxen; // 0x09: INTRRXEN + __IO uint8_t intr_txen; // 0x0A: INTRTXEN + }; + + __IO uint8_t intren_ep[2]; // 0x09-0x0A: RX, TX + }; + __I uint8_t reserved_0x0b; + + __IO uint16_t frame; // 0x0C: FRAME + __IO uint8_t index; // 0x0E: INDEX + __I uint8_t reserved_0x0f; + + musb_ep_csr_t indexed_csr; // 0x10-0x1F: Indexed CSR + __IO uint32_t fifo[16]; // 0x20-0x5F: FIFO 0-15 +} musb_regs_t; + +#else + typedef struct TU_ATTR_PACKED { __IO uint16_t maxp; // 0x00, 0x04: MAXP __IO uint8_t csrl; // 0x02, 0x06: CSRL @@ -296,6 +346,8 @@ typedef struct { TU_VERIFY_STATIC(sizeof(musb_regs_t) == 0x350, "size is not correct"); +#endif + //--------------------------------------------------------------------+ // Helper //--------------------------------------------------------------------+ diff --git a/src/portable/microchip/pic/dcd_pic.c b/src/portable/microchip/pic/dcd_pic.c index fedede8ab..7e490905c 100644 --- a/src/portable/microchip/pic/dcd_pic.c +++ b/src/portable/microchip/pic/dcd_pic.c @@ -1,31 +1,14 @@ /* - * The MIT License (MIT) + * SPDX-FileCopyrightText: Copyright (c) 2022 SudoMaker, Ltd. + * SPDX-FileCopyrightText: Copyright (c) 2020 Koji Kitayama + * SPDX-FileCopyrightText: Copyright (c) 2022 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * - * Copyright (c) 2022-2024 SudoMaker, Ltd. - * Author: Mike Yang (Reimu NotMoe) <[email protected]> + * This file is part of the TinyUSB stack. * + * Author: Mike Yang (Reimu NotMoe) <[email protected]> * Based on usb_device.c - Copyright (c) 2015 Microchip Technology Inc. * Based on dcd_khci.c - Copyright (c) 2020 Koji Kitayama - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. */ #include "tusb_option.h" diff --git a/src/portable/microchip/pic32mz/dcd_pic32mz.c b/src/portable/microchip/pic32mz/dcd_pic32mz.c index 94ecf1455..1fb5d08ad 100644 --- a/src/portable/microchip/pic32mz/dcd_pic32mz.c +++ b/src/portable/microchip/pic32mz/dcd_pic32mz.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2022 Jerzy Kasenberg - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2022 Jerzy Kasenberg + * SPDX-FileCopyrightText: Copyright (c) 2022 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/microchip/samd/dcd_samd.c b/src/portable/microchip/samd/dcd_samd.c index cdfb00e3c..54ef34c8e 100644 --- a/src/portable/microchip/samd/dcd_samd.c +++ b/src/portable/microchip/samd/dcd_samd.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2018 Scott Shawcroft for Adafruit Industries - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2018 Scott Shawcroft for Adafruit Industries + * SPDX-FileCopyrightText: Copyright (c) 2018 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -247,15 +229,49 @@ bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { (void) rhport; - (void) ep_addr; - (void)largest_packet_size; - return false; + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); + + // Reserve the endpoint bank with the largest packet size (persists across altsettings). The + // buffer address/count are filled per-transfer in dcd_edpt_xfer; only the SIZE bucket is fixed. + UsbDeviceDescBank* bank = &sram_registers[epnum][dir]; + uint32_t size_value = 0; + while (size_value < 7) { + if (1 << (size_value + 3) >= largest_packet_size) { + break; + } + size_value++; + } + if ( size_value == 7 && largest_packet_size > 1023 ) return false; + + bank->PCKSIZE.bit.SIZE = size_value; + return true; } bool dcd_edpt_iso_activate(uint8_t rhport, const tusb_desc_endpoint_t *desc_ep) { (void)rhport; - (void)desc_ep; - return false; + uint8_t const epnum = tu_edpt_number(desc_ep->bEndpointAddress); + uint8_t const dir = tu_edpt_dir(desc_ep->bEndpointAddress); + + // Configure and enable the ISO endpoint on altsetting selection (bank SIZE already reserved by + // dcd_edpt_iso_alloc). Mirrors the per-direction setup in dcd_edpt_open(), plus a bank scrub: + // under ISO_ALLOC the EP is never disabled on alt0 (usbd_edpt_close is a no-op), so the bank-ready + // state from the previous streaming session survives into re-activation. Leave the EP un-armed so + // a stale bank can't move a packet before dcd_edpt_xfer re-arms it (a leftover BK1RDY with a stale + // BYTE_COUNT would otherwise babble on the first IN token after re-selecting alt1). + UsbDeviceEndpoint* ep = &USB->DEVICE.DeviceEndpoint[epnum]; + if ( dir == TUSB_DIR_OUT ) { + ep->EPCFG.bit.EPTYPE0 = desc_ep->bmAttributes.xfer + 1; + ep->EPSTATUSCLR.reg = USB_DEVICE_EPSTATUSCLR_STALLRQ0 | USB_DEVICE_EPSTATUSCLR_DTGLOUT; + ep->EPSTATUSSET.reg = USB_DEVICE_EPSTATUSSET_BK0RDY; // OUT: not ready to receive until armed + ep->EPINTENSET.bit.TRCPT0 = true; + } else { + ep->EPCFG.bit.EPTYPE1 = desc_ep->bmAttributes.xfer + 1; + ep->EPSTATUSCLR.reg = USB_DEVICE_EPSTATUSCLR_STALLRQ1 | USB_DEVICE_EPSTATUSCLR_DTGLIN | + USB_DEVICE_EPSTATUSCLR_BK1RDY; // IN: clear stale "loaded" bank + ep->EPINTENSET.bit.TRCPT1 = true; + } + return true; } void dcd_edpt_close_all (uint8_t rhport) diff --git a/src/portable/microchip/samd/hcd_samd.c b/src/portable/microchip/samd/hcd_samd.c index 0de7ddeb6..8636200dd 100644 --- a/src/portable/microchip/samd/hcd_samd.c +++ b/src/portable/microchip/samd/hcd_samd.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024 ChrisDeadman - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024 ChrisDeadman + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/microchip/samg/dcd_samg.c b/src/portable/microchip/samg/dcd_samg.c index f8980b775..c4fb28cac 100644 --- a/src/portable/microchip/samg/dcd_samg.c +++ b/src/portable/microchip/samg/dcd_samg.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2018, hathach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2018, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/microchip/samx7x/dcd_samx7x.c b/src/portable/microchip/samx7x/dcd_samx7x.c index 6da1e9778..ea6492ad4 100644 --- a/src/portable/microchip/samx7x/dcd_samx7x.c +++ b/src/portable/microchip/samx7x/dcd_samx7x.c @@ -1,26 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2018, hathach (tinyusb.org) - * Copyright (c) 2021, HiFiPhile - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2018, Ha Thach (tinyusb.org) + * SPDX-FileCopyrightText: Copyright (c) 2021, HiFiPhile (Zixun LI) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/microchip/samx7x/samx7x_common.h b/src/portable/microchip/samx7x/samx7x_common.h index 5e3c20c0f..b34da2c36 100644 --- a/src/portable/microchip/samx7x/samx7x_common.h +++ b/src/portable/microchip/samx7x/samx7x_common.h @@ -1,30 +1,11 @@ /* -* The MIT License (MIT) -* -* Copyright (c) 2019 Microchip Technology Inc. -* Copyright (c) 2018, hathach (tinyusb.org) -* Copyright (c) 2021, HiFiPhile -* -* Permission is hereby granted, free of charge, to any person obtaining a copy -* of this software and associated documentation files (the "Software"), to deal -* in the Software without restriction, including without limitation the rights -* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell -* copies of the Software, and to permit persons to whom the Software is -* furnished to do so, subject to the following conditions: -* -* The above copyright notice and this permission notice shall be included in -* all copies or substantial portions of the Software. -* -* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR -* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, -* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE -* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER -* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, -* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN -* THE SOFTWARE. -* -* This file is part of the TinyUSB stack. -*/ + * SPDX-FileCopyrightText: Copyright (c) 2019 Microchip Technology Inc. + * SPDX-FileCopyrightText: Copyright (c) 2018, Ha Thach (tinyusb.org) + * SPDX-FileCopyrightText: Copyright (c) 2021, HiFiPhile (Zixun LI) + * SPDX-License-Identifier: MIT + * + * This file is part of the TinyUSB stack. + */ #ifndef _COMMON_USB_REGS_H_ #define _COMMON_USB_REGS_H_ diff --git a/src/portable/mindmotion/mm32/dcd_mm32f327x_otg.c b/src/portable/mindmotion/mm32/dcd_mm32f327x_otg.c index 6f88e0a24..b40d2a9f5 100644 --- a/src/portable/mindmotion/mm32/dcd_mm32f327x_otg.c +++ b/src/portable/mindmotion/mm32/dcd_mm32f327x_otg.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2020 SE TEAM - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2020 SE TEAM + * SPDX-FileCopyrightText: Copyright (c) 2020 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/nordic/nrf5x/dcd_nrf5x.c b/src/portable/nordic/nrf5x/dcd_nrf5x.c index befbaa338..5170e0645 100644 --- a/src/portable/nordic/nrf5x/dcd_nrf5x.c +++ b/src/portable/nordic/nrf5x/dcd_nrf5x.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -141,8 +122,22 @@ TU_ATTR_ALWAYS_INLINE static inline bool is_in_isr(void) { return (SCB->ICSR & SCB_ICSR_VECTACTIVE_Msk) ? true : false; } +// Errata 199 "USBD cannot receive tasks during DMA": while an EasyDMA transfer is in progress the +// controller may drop an incoming SETUP/IN/OUT token (lost event -> stuck EP0, esp. under rapid +// back-to-back control transfers). The workaround latches an undocumented "DMA in progress" test +// register (0x40027C1C) so tokens are held instead. Gated on the anomaly being present (all +// nRF52840 revisions; absent on other nRF52 parts). Mirrors nrfx usbd_dma_pending_set/clear(). +#define NRF_USBD_ERRATA_199_REG (*((volatile uint32_t*) 0x40027C1CUL)) + // helper to start DMA static void start_dma(volatile uint32_t* reg_startep) { + // EP0STATUS / EP0RCVOUT take the EasyDMA slot but do not transfer data, so no ERRATA-199 latch. + const bool no_dma = (reg_startep == &NRF_USBD->TASKS_EP0STATUS) || (reg_startep == &NRF_USBD->TASKS_EP0RCVOUT); + + if (!no_dma && nrf52_errata_199()) { + NRF_USBD_ERRATA_199_REG = 0x00000082UL; + } + (*reg_startep) = 1; __ISB(); __DSB(); @@ -150,7 +145,7 @@ static void start_dma(volatile uint32_t* reg_startep) { // TASKS_EP0STATUS, TASKS_EP0RCVOUT seem to need EasyDMA to be available // However these don't trigger any DMA transfer and got ENDED event subsequently // Therefore dma_pending is corrected right away - if ((reg_startep == &NRF_USBD->TASKS_EP0STATUS) || (reg_startep == &NRF_USBD->TASKS_EP0RCVOUT)) { + if (no_dma) { atomic_flag_clear(&_dcd.dma_running); } } @@ -165,6 +160,10 @@ static void edpt_dma_start(volatile uint32_t* reg_startep) { // DMA is complete static void edpt_dma_end(void) { + // Clear the ERRATA-199 "DMA in progress" latch set in start_dma(). + if (nrf52_errata_199()) { + NRF_USBD_ERRATA_199_REG = 0x00000000UL; + } atomic_flag_clear(&_dcd.dma_running); } @@ -396,58 +395,52 @@ void dcd_edpt_close_all(uint8_t rhport) { dcd_int_enable(rhport); } -void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) { - (void) rhport; +bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { + (void)rhport; + (void)largest_packet_size; + // nRF ISO endpoints are hardware-fixed to EP8 and use EasyDMA, so there is no packet buffer to + // pre-allocate here; the endpoint is enabled on dcd_edpt_iso_activate(). + TU_ASSERT(tu_edpt_number(ep_addr) == EP_ISO_NUM); + return true; +} +bool dcd_edpt_iso_activate(uint8_t rhport, const tusb_desc_endpoint_t *desc_ep) { + (void)rhport; + uint8_t const ep_addr = desc_ep->bEndpointAddress; uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const dir = tu_edpt_dir(ep_addr); + TU_ASSERT(epnum == EP_ISO_NUM); - if (epnum != EP_ISO_NUM) { - // CBI - if (dir == TUSB_DIR_OUT) { - NRF_USBD->INTENCLR = TU_BIT(USBD_INTEN_ENDEPOUT0_Pos + epnum); - NRF_USBD->EPOUTEN &= ~TU_BIT(epnum); - } else { - NRF_USBD->INTENCLR = TU_BIT(USBD_INTEN_ENDEPIN0_Pos + epnum); - NRF_USBD->EPINEN &= ~TU_BIT(epnum); - } + // A transfer armed before SET_INTERFACE survives to here (this port has no dcd close); usbd has + // just reset the endpoint's claim/busy state, so drop the stale descriptor too — otherwise the + // class's next arm trips TU_ASSERT(!xfer->started) in dcd_edpt_xfer(). + _dcd.xfer[epnum][dir].started = false; + _dcd.xfer[epnum][dir].data_received = false; + _dcd.xfer[epnum][dir].iso_in_transfer_ready = false; + + _dcd.xfer[epnum][dir].mps = tu_edpt_packet_size(desc_ep); + + if (dir == TUSB_DIR_OUT) { + // SPLIT ISO buffer when the ISO IN endpoint is already active. + if (_dcd.xfer[EP_ISO_NUM][TUSB_DIR_IN].mps) NRF_USBD->ISOSPLIT = USBD_ISOSPLIT_SPLIT_HalfIN; + NRF_USBD->EVENTS_ENDISOOUT = 0; + if ((NRF_USBD->INTEN & USBD_INTEN_SOF_Msk) == 0) NRF_USBD->EVENTS_SOF = 0; + NRF_USBD->INTENSET = USBD_INTENSET_ENDISOOUT_Msk | USBD_INTENSET_SOF_Msk; + NRF_USBD->EPOUTEN |= USBD_EPOUTEN_ISOOUT_Msk; } else { - _dcd.xfer[EP_ISO_NUM][dir].mps = 0; - // ISO - if (dir == TUSB_DIR_OUT) { - NRF_USBD->INTENCLR = USBD_INTENCLR_ENDISOOUT_Msk; - NRF_USBD->EPOUTEN &= ~USBD_EPOUTEN_ISOOUT_Msk; - NRF_USBD->EVENTS_ENDISOOUT = 0; - } else { - NRF_USBD->INTENCLR = USBD_INTENCLR_ENDISOIN_Msk; - NRF_USBD->EPINEN &= ~USBD_EPINEN_ISOIN_Msk; - } - // One of the ISO endpoints closed, no need to split buffers any more. - NRF_USBD->ISOSPLIT = USBD_ISOSPLIT_SPLIT_OneDir; - // When both ISO endpoint are close there is no need for SOF any more. - if (_dcd.xfer[EP_ISO_NUM][TUSB_DIR_IN].mps + _dcd.xfer[EP_ISO_NUM][TUSB_DIR_OUT].mps == 0) - NRF_USBD->INTENCLR = USBD_INTENCLR_SOF_Msk; + NRF_USBD->EVENTS_ENDISOIN = 0; + // SPLIT ISO buffer when the ISO OUT endpoint is already active. + if (_dcd.xfer[EP_ISO_NUM][TUSB_DIR_OUT].mps) NRF_USBD->ISOSPLIT = USBD_ISOSPLIT_SPLIT_HalfIN; + if ((NRF_USBD->INTEN & USBD_INTEN_SOF_Msk) == 0) NRF_USBD->EVENTS_SOF = 0; + NRF_USBD->INTENSET = USBD_INTENSET_ENDISOIN_Msk | USBD_INTENSET_SOF_Msk; + NRF_USBD->EPINEN |= USBD_EPINEN_ISOIN_Msk; } - _dcd.xfer[epnum][dir].started = false; + __ISB(); __DSB(); + return true; } -#if 0 -bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { - (void)rhport; - (void)ep_addr; - (void)largest_packet_size; - return false; -} - -bool dcd_edpt_iso_activate(uint8_t rhport, const tusb_desc_endpoint_t *desc_ep) { - (void)rhport; - (void)desc_ep; - return false; -} -#endif - bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t* buffer, uint16_t total_bytes, bool is_isr) { (void) rhport; (void) is_isr; @@ -862,6 +855,10 @@ static bool hfclk_running(void) { #if CFG_TUD_NRF_NRFX_VERSION == 1 return nrf_clock_hf_is_running(NRF_CLOCK_HFCLK_HIGH_ACCURACY); + #elif CFG_TUD_NRF_NRFX_VERSION == 2 + // nrfx 2.0.0 (MDK 8.29.0) has no nrf_clock_is_running(); it arrived in 2.1.0. + // nrf_clock_hf_is_running() is present in all of 2.0.0-2.11.0 (deprecated from 2.1.0). + return nrf_clock_hf_is_running(NRF_CLOCK, NRF_CLOCK_HFCLK_HIGH_ACCURACY); #else return nrf_clock_is_running(NRF_CLOCK, NRF_CLOCK_DOMAIN_HFCLK, NULL); #endif diff --git a/src/portable/nuvoton/nuc120/dcd_nuc120.c b/src/portable/nuvoton/nuc120/dcd_nuc120.c index 2edb1bc7a..513262ea4 100644 --- a/src/portable/nuvoton/nuc120/dcd_nuc120.c +++ b/src/portable/nuvoton/nuc120/dcd_nuc120.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019-2020 Peter Lawrence - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Peter Lawrence + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/nuvoton/nuc121/dcd_nuc121.c b/src/portable/nuvoton/nuc121/dcd_nuc121.c index 008c9df6b..b2859347c 100644 --- a/src/portable/nuvoton/nuc121/dcd_nuc121.c +++ b/src/portable/nuvoton/nuc121/dcd_nuc121.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Peter Lawrence - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Peter Lawrence + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/nuvoton/nuc505/dcd_nuc505.c b/src/portable/nuvoton/nuc505/dcd_nuc505.c index a0f3d4c3f..ece7911a1 100644 --- a/src/portable/nuvoton/nuc505/dcd_nuc505.c +++ b/src/portable/nuvoton/nuc505/dcd_nuc505.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2020 Peter Lawrence - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2020 Peter Lawrence + * SPDX-FileCopyrightText: Copyright (c) 2020 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/nxp/khci/dcd_khci.c b/src/portable/nxp/khci/dcd_khci.c deleted file mode 100644 index ad27b8528..000000000 --- a/src/portable/nxp/khci/dcd_khci.c +++ /dev/null @@ -1,578 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2020 Koji Kitayama - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "tusb_option.h" - -#if CFG_TUD_ENABLED && defined(TUP_USBIP_CHIPIDEA_FS) - -#ifdef TUP_USBIP_CHIPIDEA_FS_KINETIS - #include "fsl_device_registers.h" - #define KHCI USB0 -#else - #error "MCU is not supported" -#endif - -#include "device/dcd.h" - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM DECLARATION -//--------------------------------------------------------------------+ - -enum { - TOK_PID_OUT = 0x1u, - TOK_PID_IN = 0x9u, - TOK_PID_SETUP = 0xDu, -}; - -typedef struct TU_ATTR_PACKED -{ - union { - uint32_t head; - struct { - union { - struct { - uint16_t : 2; - __IO uint16_t tok_pid : 4; - uint16_t data : 1; - __IO uint16_t own : 1; - uint16_t : 8; - }; - struct { - uint16_t : 2; - uint16_t bdt_stall : 1; - uint16_t dts : 1; - uint16_t ninc : 1; - uint16_t keep : 1; - uint16_t : 10; - }; - }; - __IO uint16_t bc : 10; - uint16_t : 6; - }; - }; - uint8_t *addr; -}buffer_descriptor_t; - -TU_VERIFY_STATIC( sizeof(buffer_descriptor_t) == 8, "size is not correct" ); - -typedef struct TU_ATTR_PACKED -{ - union { - uint32_t state; - struct { - uint32_t max_packet_size :11; - uint32_t : 5; - uint32_t odd : 1; - uint32_t :15; - }; - }; - uint16_t length; - uint16_t remaining; -}endpoint_state_t; - -TU_VERIFY_STATIC( sizeof(endpoint_state_t) == 8, "size is not correct" ); - -typedef struct -{ - union { - /* [#EP][OUT,IN][EVEN,ODD] */ - buffer_descriptor_t bdt[16][2][2]; - uint16_t bda[512]; - }; - TU_ATTR_ALIGNED(4) union { - endpoint_state_t endpoint[16][2]; - endpoint_state_t endpoint_unified[16 * 2]; - }; - uint8_t setup_packet[8]; - uint8_t addr; -}dcd_data_t; - -//--------------------------------------------------------------------+ -// INTERNAL OBJECT & FUNCTION DECLARATION -//--------------------------------------------------------------------+ -// BDT(Buffer Descriptor Table) must be 256-byte aligned -CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(512) static dcd_data_t _dcd; - -TU_VERIFY_STATIC( sizeof(_dcd.bdt) == 512, "size is not correct" ); - -static void prepare_next_setup_packet(uint8_t rhport) -{ - const unsigned out_odd = _dcd.endpoint[0][0].odd; - const unsigned in_odd = _dcd.endpoint[0][1].odd; - TU_ASSERT(0 == _dcd.bdt[0][0][out_odd].own, ); - - _dcd.bdt[0][0][out_odd].data = 0; - _dcd.bdt[0][0][out_odd ^ 1].data = 1; - _dcd.bdt[0][1][in_odd].data = 1; - _dcd.bdt[0][1][in_odd ^ 1].data = 0; - dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_OUT), - _dcd.setup_packet, sizeof(_dcd.setup_packet), false); -} - -static void process_stall(uint8_t rhport) -{ - for (int i = 0; i < 16; ++i) { - unsigned const endpt = KHCI->ENDPOINT[i].ENDPT; - - if (endpt & USB_ENDPT_EPSTALL_MASK) { - // prepare next setup if endpoint0 - if ( i == 0 ) prepare_next_setup_packet(rhport); - - // clear stall bit - KHCI->ENDPOINT[i].ENDPT = endpt & ~USB_ENDPT_EPSTALL_MASK; - } - } -} - -static void process_tokdne(uint8_t rhport) -{ - const unsigned s = KHCI->STAT; - KHCI->ISTAT = USB_ISTAT_TOKDNE_MASK; /* fetch the next token if received */ - - uint8_t const epnum = (s >> USB_STAT_ENDP_SHIFT); - uint8_t const dir = (s & USB_STAT_TX_MASK) >> USB_STAT_TX_SHIFT; - unsigned const odd = (s & USB_STAT_ODD_MASK) ? 1 : 0; - - buffer_descriptor_t *bd = (buffer_descriptor_t *)&_dcd.bda[s]; - endpoint_state_t *ep = &_dcd.endpoint_unified[s >> 3]; - - /* fetch pid before discarded by the next steps */ - const unsigned pid = bd->tok_pid; - - /* reset values for a next transfer */ - bd->bdt_stall = 0; - bd->dts = 1; - bd->ninc = 0; - bd->keep = 0; - /* update the odd variable to prepare for the next transfer */ - ep->odd = odd ^ 1; - if (pid == TOK_PID_SETUP) { - dcd_event_setup_received(rhport, bd->addr, true); - KHCI->CTL &= ~USB_CTL_TXSUSPENDTOKENBUSY_MASK; - return; - } - - const unsigned bc = bd->bc; - const unsigned remaining = ep->remaining - bc; - if (remaining && bc == ep->max_packet_size) { - /* continue the transferring consecutive data */ - ep->remaining = remaining; - const int next_remaining = remaining - ep->max_packet_size; - if (next_remaining > 0) { - /* prepare to the after next transfer */ - bd->addr += ep->max_packet_size * 2; - bd->bc = next_remaining > ep->max_packet_size ? ep->max_packet_size: next_remaining; - __DSB(); - bd->own = 1; /* the own bit must set after addr */ - } - return; - } - const unsigned length = ep->length; - dcd_event_xfer_complete(rhport, - tu_edpt_addr(epnum, dir), - length - remaining, XFER_RESULT_SUCCESS, true); - if (0 == epnum && 0 == length) { - /* After completion a ZLP of control transfer, - * it prepares for the next steup transfer. */ - if (_dcd.addr) { - /* When the transfer was the SetAddress, - * the device address should be updated here. */ - KHCI->ADDR = _dcd.addr; - _dcd.addr = 0; - } - prepare_next_setup_packet(rhport); - } -} - -static void process_bus_reset(uint8_t rhport) -{ - KHCI->USBCTRL &= ~USB_USBCTRL_SUSP_MASK; - KHCI->CTL |= USB_CTL_ODDRST_MASK; - KHCI->ADDR = 0; - KHCI->INTEN = USB_INTEN_USBRSTEN_MASK | USB_INTEN_TOKDNEEN_MASK | USB_INTEN_SLEEPEN_MASK | - USB_INTEN_ERROREN_MASK | USB_INTEN_STALLEN_MASK; - - KHCI->ENDPOINT[0].ENDPT = USB_ENDPT_EPHSHK_MASK | USB_ENDPT_EPRXEN_MASK | USB_ENDPT_EPTXEN_MASK; - for (unsigned i = 1; i < 16; ++i) { - KHCI->ENDPOINT[i].ENDPT = 0; - } - buffer_descriptor_t *bd = _dcd.bdt[0][0]; - for (unsigned i = 0; i < sizeof(_dcd.bdt)/sizeof(*bd); ++i, ++bd) { - bd->head = 0; - } - const endpoint_state_t ep0 = { - .max_packet_size = CFG_TUD_ENDPOINT0_SIZE, - .odd = 0, - .length = 0, - .remaining = 0, - }; - _dcd.endpoint[0][0] = ep0; - _dcd.endpoint[0][1] = ep0; - tu_memclr(_dcd.endpoint[1], sizeof(_dcd.endpoint) - sizeof(_dcd.endpoint[0])); - _dcd.addr = 0; - prepare_next_setup_packet(rhport); - KHCI->CTL &= ~USB_CTL_ODDRST_MASK; - dcd_event_bus_reset(rhport, TUSB_SPEED_FULL, true); -} - -static void process_bus_sleep(uint8_t rhport) -{ - // Enable resume & disable suspend interrupt - const unsigned inten = KHCI->INTEN; - - KHCI->INTEN = (inten & ~USB_INTEN_SLEEPEN_MASK) | USB_INTEN_RESUMEEN_MASK; - KHCI->USBTRC0 |= USB_USBTRC0_USBRESMEN_MASK; - KHCI->USBCTRL |= USB_USBCTRL_SUSP_MASK; - - dcd_event_bus_signal(rhport, DCD_EVENT_SUSPEND, true); -} - -static void process_bus_resume(uint8_t rhport) -{ - // Enable suspend & disable resume interrupt - const unsigned inten = KHCI->INTEN; - - KHCI->USBCTRL &= ~USB_USBCTRL_SUSP_MASK; // will also clear USB_USBTRC0_USB_RESUME_INT_MASK - KHCI->USBTRC0 &= ~USB_USBTRC0_USBRESMEN_MASK; - KHCI->INTEN = (inten & ~USB_INTEN_RESUMEEN_MASK) | USB_INTEN_SLEEPEN_MASK; - - dcd_event_bus_signal(rhport, DCD_EVENT_RESUME, true); -} - -/*------------------------------------------------------------------*/ -/* Device API - *------------------------------------------------------------------*/ -bool dcd_init(uint8_t rhport, const tusb_rhport_init_t* rh_init) { - (void) rhport; - (void) rh_init; - - // save crystal-less setting (if available) - #if defined(FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED) && FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED == 1 - uint32_t clk_recover_irc_en = KHCI->CLK_RECOVER_IRC_EN; - uint32_t clk_recover_ctrl = KHCI->CLK_RECOVER_CTRL; - #endif - - KHCI->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; - while (KHCI->USBTRC0 & USB_USBTRC0_USBRESET_MASK); - - // restore crystal-less setting (if available) - #if defined(FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED) && FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED == 1 - KHCI->CLK_RECOVER_IRC_EN = clk_recover_irc_en; - KHCI->CLK_RECOVER_CTRL |= clk_recover_ctrl; - #endif - - tu_memclr(&_dcd, sizeof(_dcd)); - KHCI->USBTRC0 |= TU_BIT(6); /* software must set this bit to 1 */ - KHCI->BDTPAGE1 = (uint8_t)((uintptr_t)_dcd.bdt >> 8); - KHCI->BDTPAGE2 = (uint8_t)((uintptr_t)_dcd.bdt >> 16); - KHCI->BDTPAGE3 = (uint8_t)((uintptr_t)_dcd.bdt >> 24); - - KHCI->INTEN = USB_INTEN_USBRSTEN_MASK; - - dcd_connect(rhport); - NVIC_ClearPendingIRQ(USB0_IRQn); - - return true; -} - -void dcd_int_enable(uint8_t rhport) -{ - (void) rhport; - NVIC_EnableIRQ(USB0_IRQn); -} - -void dcd_int_disable(uint8_t rhport) -{ - (void) rhport; - NVIC_DisableIRQ(USB0_IRQn); -} - -void dcd_set_address(uint8_t rhport, uint8_t dev_addr) -{ - _dcd.addr = dev_addr & 0x7F; - /* Response with status first before changing device address */ - dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_IN), NULL, 0, false); -} - -void dcd_remote_wakeup(uint8_t rhport) -{ - (void) rhport; - - KHCI->CTL |= USB_CTL_RESUME_MASK; - - unsigned cnt = SystemCoreClock / 1000; - while (cnt--) __NOP(); - - KHCI->CTL &= ~USB_CTL_RESUME_MASK; -} - -void dcd_connect(uint8_t rhport) -{ - (void) rhport; - KHCI->USBCTRL = 0; - KHCI->CONTROL |= USB_CONTROL_DPPULLUPNONOTG_MASK; - KHCI->CTL |= USB_CTL_USBENSOFEN_MASK; -} - -void dcd_disconnect(uint8_t rhport) -{ - (void) rhport; - KHCI->CTL = 0; - KHCI->CONTROL &= ~USB_CONTROL_DPPULLUPNONOTG_MASK; -} - -void dcd_sof_enable(uint8_t rhport, bool en) -{ - (void) rhport; - (void) en; - - // TODO implement later -} - -//--------------------------------------------------------------------+ -// Endpoint API -//--------------------------------------------------------------------+ -static bool edpt_open(uint8_t rhport, uint8_t ep_addr, uint16_t max_packet_size, tusb_xfer_type_t xfer) { - (void)rhport; - - const unsigned epn = tu_edpt_number(ep_addr); - const unsigned dir = tu_edpt_dir(ep_addr); - endpoint_state_t *ep = &_dcd.endpoint[epn][dir]; - const unsigned odd = ep->odd; - buffer_descriptor_t *bd = _dcd.bdt[epn][dir]; - - /* No support for control transfer */ - TU_ASSERT(epn && (xfer != TUSB_XFER_CONTROL)); - - ep->max_packet_size = max_packet_size; - unsigned val = USB_ENDPT_EPCTLDIS_MASK; - val |= (xfer != TUSB_XFER_ISOCHRONOUS) ? USB_ENDPT_EPHSHK_MASK : 0; - val |= dir ? USB_ENDPT_EPTXEN_MASK : USB_ENDPT_EPRXEN_MASK; - KHCI->ENDPOINT[epn].ENDPT |= val; - - if (xfer != TUSB_XFER_ISOCHRONOUS) { - bd[odd].dts = 1; - bd[odd].data = 0; - bd[odd ^ 1].dts = 1; - bd[odd ^ 1].data = 1; - } - - return true; -} - -bool dcd_edpt_open(uint8_t rhport, const tusb_desc_endpoint_t *ep_desc) { - return edpt_open(rhport, ep_desc->bEndpointAddress, tu_edpt_packet_size(ep_desc), ep_desc->bmAttributes.xfer); -} - -bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { - return edpt_open(rhport, ep_addr, largest_packet_size, TUSB_XFER_ISOCHRONOUS); -} - -bool dcd_edpt_iso_activate(uint8_t rhport, const tusb_desc_endpoint_t *ep_desc) { - const unsigned epn = tu_edpt_number(ep_desc->bEndpointAddress); - const unsigned dir = tu_edpt_dir(ep_desc->bEndpointAddress); - endpoint_state_t *ep = &_dcd.endpoint[epn][dir]; - - dcd_int_disable(rhport); - ep->max_packet_size = tu_edpt_packet_size(ep_desc); - dcd_int_enable(rhport); - - return true; -} - -void dcd_edpt_close_all(uint8_t rhport) -{ - (void) rhport; - const unsigned ie = NVIC_GetEnableIRQ(USB0_IRQn); - NVIC_DisableIRQ(USB0_IRQn); - for (unsigned i = 1; i < 16; ++i) { - KHCI->ENDPOINT[i].ENDPT = 0; - } - if (ie) NVIC_EnableIRQ(USB0_IRQn); - buffer_descriptor_t *bd = _dcd.bdt[1][0]; - for (unsigned i = 2; i < sizeof(_dcd.bdt)/sizeof(*bd); ++i, ++bd) { - bd->head = 0; - } - endpoint_state_t *ep = &_dcd.endpoint[1][0]; - for (unsigned i = 2; i < sizeof(_dcd.endpoint)/sizeof(*ep); ++i, ++ep) { - /* Clear except the odd */ - ep->max_packet_size = 0; - ep->length = 0; - ep->remaining = 0; - } -} - -bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes, bool is_isr) -{ - (void) rhport; - (void) is_isr; - const unsigned epn = tu_edpt_number(ep_addr); - const unsigned dir = tu_edpt_dir(ep_addr); - endpoint_state_t *ep = &_dcd.endpoint[epn][dir]; - buffer_descriptor_t *bd = &_dcd.bdt[epn][dir][ep->odd]; - TU_ASSERT(0 == bd->own); - - const unsigned ie = NVIC_GetEnableIRQ(USB0_IRQn); - NVIC_DisableIRQ(USB0_IRQn); - - ep->length = total_bytes; - ep->remaining = total_bytes; - - const unsigned mps = ep->max_packet_size; - if (total_bytes > mps) { - buffer_descriptor_t *next = ep->odd ? bd - 1: bd + 1; - /* When total_bytes is greater than the max packet size, - * it prepares to the next transfer to avoid NAK in advance. */ - next->bc = total_bytes >= 2 * mps ? mps: total_bytes - mps; - next->addr = buffer + mps; - next->own = 1; - } - bd->bc = total_bytes >= mps ? mps: total_bytes; - bd->addr = buffer; - __DSB(); - bd->own = 1; /* This bit must be set last */ - - if (ie) NVIC_EnableIRQ(USB0_IRQn); - return true; -} - -void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) -{ - (void) rhport; - const unsigned epn = tu_edpt_number(ep_addr); - - if (0 == epn) { - KHCI->ENDPOINT[epn].ENDPT |= USB_ENDPT_EPSTALL_MASK; - } else { - const unsigned dir = tu_edpt_dir(ep_addr); - const unsigned odd = _dcd.endpoint[epn][dir].odd; - buffer_descriptor_t *bd = &_dcd.bdt[epn][dir][odd]; - TU_ASSERT(0 == bd->own,); - - const unsigned ie = NVIC_GetEnableIRQ(USB0_IRQn); - NVIC_DisableIRQ(USB0_IRQn); - - bd->bdt_stall = 1; - __DSB(); - bd->own = 1; /* This bit must be set last */ - - if (ie) NVIC_EnableIRQ(USB0_IRQn); - } -} - -void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) -{ - (void) rhport; - const unsigned epn = tu_edpt_number(ep_addr); - TU_VERIFY(epn,); - const unsigned dir = tu_edpt_dir(ep_addr); - const unsigned odd = _dcd.endpoint[epn][dir].odd; - buffer_descriptor_t *bd = _dcd.bdt[epn][dir]; - TU_VERIFY(bd[odd].own,); - - const unsigned ie = NVIC_GetEnableIRQ(USB0_IRQn); - NVIC_DisableIRQ(USB0_IRQn); - - bd[odd].own = 0; - __DSB(); - - // clear stall - bd[odd].bdt_stall = 0; - - // Reset data toggle - bd[odd ].data = 0; - bd[odd ^ 1].data = 1; - - // We already cleared this in ISR, but just clear it here to be safe - const unsigned endpt = KHCI->ENDPOINT[epn].ENDPT; - if (endpt & USB_ENDPT_EPSTALL_MASK) { - KHCI->ENDPOINT[epn].ENDPT = endpt & ~USB_ENDPT_EPSTALL_MASK; - } - - if (ie) NVIC_EnableIRQ(USB0_IRQn); -} - -//--------------------------------------------------------------------+ -// ISR -//--------------------------------------------------------------------+ -void dcd_int_handler(uint8_t rhport) -{ - uint32_t is = KHCI->ISTAT; - uint32_t msk = KHCI->INTEN; - - // clear non-enabled interrupts - KHCI->ISTAT = is & ~msk; - is &= msk; - - if (is & USB_ISTAT_ERROR_MASK) { - /* TODO: */ - uint32_t es = KHCI->ERRSTAT; - KHCI->ERRSTAT = es; - KHCI->ISTAT = is; /* discard any pending events */ - } - - if (is & USB_ISTAT_USBRST_MASK) { - KHCI->ISTAT = is; /* discard any pending events */ - process_bus_reset(rhport); - } - - if (is & USB_ISTAT_SLEEP_MASK) { - // TU_LOG3("Suspend: "); TU_LOG2_HEX(is); - - // Note Host usually has extra delay after bus reset (without SOF), which could falsely - // detected as Sleep event. Though usbd has debouncing logic so we are good - KHCI->ISTAT = USB_ISTAT_SLEEP_MASK; - process_bus_sleep(rhport); - } - -#if 0 // ISTAT_RESUME never trigger, probably for host mode ? - if (is & USB_ISTAT_RESUME_MASK) { - // TU_LOG2("ISTAT Resume: "); TU_LOG2_HEX(is); - KHCI->ISTAT = USB_ISTAT_RESUME_MASK; - process_bus_resume(rhport); - } -#endif - - if (KHCI->USBTRC0 & USB_USBTRC0_USB_RESUME_INT_MASK) { - // TU_LOG2("USBTRC0 Resume: "); TU_LOG2_HEX(is); TU_LOG2_HEX(KHCI->USBTRC0); - process_bus_resume(rhport); - } - - if (is & USB_ISTAT_SOFTOK_MASK) { - KHCI->ISTAT = USB_ISTAT_SOFTOK_MASK; - dcd_event_sof(rhport, tu_u16(KHCI->FRMNUMH, KHCI->FRMNUML), true); - } - - if (is & USB_ISTAT_STALL_MASK) { - KHCI->ISTAT = USB_ISTAT_STALL_MASK; - process_stall(rhport); - } - - if (is & USB_ISTAT_TOKDNE_MASK) { - process_tokdne(rhport); - } -} -#endif diff --git a/src/portable/nxp/lpc17_40/dcd_lpc17_40.c b/src/portable/nxp/lpc17_40/dcd_lpc17_40.c index 2840c6d5e..b577d0e9f 100644 --- a/src/portable/nxp/lpc17_40/dcd_lpc17_40.c +++ b/src/portable/nxp/lpc17_40/dcd_lpc17_40.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -38,6 +19,12 @@ //--------------------------------------------------------------------+ #define DCD_ENDPOINT_MAX 32 +// The iso machinery (5th DD word + packet-size memory) costs USB RAM on every build; +// compile it only when a class that can open an iso endpoint is enabled. Keep this in +// sync with the classes that actually arm an iso endpoint: audio, video, BTH (voice), +// and vendor (its optional CFG_TUD_VENDOR_EP_ISO_* endpoints, exercised by usbtest). +#define DCD_ISO_ENABLED (CFG_TUD_AUDIO || CFG_TUD_VIDEO || CFG_TUD_VENDOR || CFG_TUD_BTH) + typedef struct TU_ATTR_ALIGNED(4) { //------------- Word 0 -------------// @@ -67,11 +54,37 @@ typedef struct TU_ATTR_ALIGNED(4) volatile uint16_t present_count; // For non-iso : The number of bytes transferred by the DMA engine // For iso : number of packets +#if DCD_ISO_ENABLED //------------- Word 4 -------------// - // uint32_t iso_packet_size_addr; // iso only, can be omitted for non-iso + volatile uint32_t iso_packet_size_addr; // iso only: pointer into iso packet-size memory, + // advanced by hardware after each packet +#endif }dma_desc_t; -TU_VERIFY_STATIC( sizeof(dma_desc_t) == 16, "size is not correct"); // TODO not support ISO for now +TU_VERIFY_STATIC( sizeof(dma_desc_t) == (DCD_ISO_ENABLED ? 20 : 16), "size is not correct"); + +// Hardware fixes endpoint type by number: 3, 6, 9, 12 are the iso-capable ones. +// Constant per ep_id (= 2*epnum + dir) — unlike dd->isochronous, which dcd_edpt_xfer +// transiently zeroes while rebuilding the DD, this is safe to dispatch on from the ISR. +// TU_ATTR_UNUSED: every caller is under #if DCD_ISO_ENABLED, so non-iso builds don't +// reference it and clang -Wunused-function (fatal) would otherwise reject the build. +TU_ATTR_UNUSED TU_ATTR_ALWAYS_INLINE static inline bool ep_id_is_iso(uint8_t ep_id) { + uint8_t const epnum = (uint8_t)(ep_id >> 1); + return (epnum % 3) == 0 && (epnum != 0) && (epnum != 15); +} + +#if DCD_ISO_ENABLED +// Isochronous packet-size memory (UM10562 12.15.6.3): one word per packet. +// IN : software fills Packet_length (bits 15:0), 0 = ZLP +// OUT: hardware writes Frame_number (31:17) | Packet_valid (16) | Packet_length (15:0) +// Iso-capable endpoint numbers are 3, 6, 9, 12 -> 8 slots (x2 directions). +// One packet moves per FRAME, so a deep queue only adds latency: 8 frames is plenty. +#define ISO_MAX_PACKETS 8 +#define ISO_SLOT_COUNT 8 +TU_ATTR_ALWAYS_INLINE static inline uint8_t iso_slot(uint8_t ep_id) { + return (uint8_t)(((ep_id / 6) - 1) * 2 + (ep_id & 1)); // ep_id = 2*epnum + dir, epnum in {3,6,9,12} +} +#endif typedef struct { @@ -85,11 +98,17 @@ typedef struct { uint8_t* out_buffer; uint8_t out_bytes; + volatile bool out_queued; // an OUT xfer is queued; out_buffer may legitimately be NULL (status ZLP) volatile bool out_received; // indicate if data is already received in endpoint uint8_t in_bytes; } control; +#if DCD_ISO_ENABLED + // iso packet-size memory, must be DMA-reachable like the DDs + volatile uint32_t iso_psize[ISO_SLOT_COUNT][ISO_MAX_PACKETS]; +#endif + } dcd_data_t; CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(128) static dcd_data_t _dcd; @@ -98,6 +117,29 @@ CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(128) static dcd_data_t _dcd; //--------------------------------------------------------------------+ // SIE Command //--------------------------------------------------------------------+ + +// The SIE command protocol (CmdCode + CCEMPTY/CDFULL handshake) and the +// slave-mode Ctrl/RxData/TxData registers are shared between thread-mode API +// calls and dcd_int_handler, and are not reentrant: an ISR preempting a +// thread-mode SIE sequence consumes its handshake flags and overwrites +// CmdCode (symptom: EP0 wedges/answers stale data right after SET_INTERFACE +// stall/clear-stall bursts overlapping bulk EOT interrupts). Mask only the +// USB interrupt around those sequences; safe to nest, including from the ISR. +static inline bool usb_irq_lock(void) +{ + bool const enabled = NVIC_GetEnableIRQ(USB_IRQn) != 0; + if (enabled) + { + NVIC_DisableIRQ(USB_IRQn); // CMSIS already ends this with DSB+ISB + } + return enabled; +} + +static inline void usb_irq_unlock(bool enabled) +{ + if (enabled) NVIC_EnableIRQ(USB_IRQn); +} + static void sie_cmd_code (sie_cmdphase_t phase, uint8_t code_data) { LPC_USB->DevIntClr = (DEV_INT_COMMAND_CODE_EMPTY_MASK | DEV_INT_COMMAND_DATA_FULL_MASK); @@ -111,19 +153,28 @@ static void sie_cmd_code (sie_cmdphase_t phase, uint8_t code_data) static void sie_write (uint8_t cmd_code, uint8_t data_len, uint8_t data) { + bool const lock = usb_irq_lock(); + sie_cmd_code(SIE_CMDPHASE_COMMAND, cmd_code); if (data_len) { sie_cmd_code(SIE_CMDPHASE_WRITE, data); } + + usb_irq_unlock(lock); } static uint8_t sie_read (uint8_t cmd_code) { + bool const lock = usb_irq_lock(); + sie_cmd_code(SIE_CMDPHASE_COMMAND , cmd_code); sie_cmd_code(SIE_CMDPHASE_READ , cmd_code); - return (uint8_t) LPC_USB->CmdData; + uint8_t const data = (uint8_t) LPC_USB->CmdData; + + usb_irq_unlock(lock); + return data; } //--------------------------------------------------------------------+ @@ -136,6 +187,11 @@ static inline uint8_t ep_addr2idx(uint8_t ep_addr) static void set_ep_size(uint8_t ep_id, uint16_t max_packet_size) { + // ReEp RMW + the EP_RLZED handshake share DevIntSt with the ISR: a bus reset + // from dcd_int_handler writes DevIntClr = 0xFFFFFFFF and would consume the + // flag this spin waits on, hanging it forever -> same lock as the SIE paths. + bool const lock = usb_irq_lock(); + // follows example in 11.10.4.2 LPC_USB->ReEp |= TU_BIT(ep_id); LPC_USB->EpInd = ep_id; // select index before setting packet size @@ -143,6 +199,8 @@ static void set_ep_size(uint8_t ep_id, uint16_t max_packet_size) while ((LPC_USB->DevIntSt & DEV_INT_ENDPOINT_REALIZED_MASK) == 0) {} LPC_USB->DevIntClr = DEV_INT_ENDPOINT_REALIZED_MASK; + + usb_irq_unlock(lock); } @@ -249,6 +307,7 @@ static inline uint8_t byte2dword(uint8_t bytes) static void control_ep_write(void const * buffer, uint8_t len) { uint32_t const * buf32 = (uint32_t const *) buffer; + bool const lock = usb_irq_lock(); // Ctrl/TxData + SIE sequence must not interleave with the ISR LPC_USB->Ctrl = USBCTRL_WRITE_ENABLE_MASK; // logical endpoint = 0 LPC_USB->TxPLen = (uint32_t) len; @@ -264,10 +323,14 @@ static void control_ep_write(void const * buffer, uint8_t len) // select control IN & validate the endpoint sie_write(SIE_CMDCODE_ENDPOINT_SELECT+1, 0, 0); sie_write(SIE_CMDCODE_BUFFER_VALIDATE , 0, 0); + + usb_irq_unlock(lock); } static uint8_t control_ep_read(void * buffer, uint8_t len) { + bool const lock = usb_irq_lock(); // Ctrl/RxData + SIE sequence must not interleave with the ISR + LPC_USB->Ctrl = USBCTRL_READ_ENABLE_MASK; // logical endpoint = 0 while ((LPC_USB->RxPLen & USBRXPLEN_PACKET_READY_MASK) == 0) {} // TODO blocking, should have timeout @@ -286,6 +349,7 @@ static uint8_t control_ep_read(void * buffer, uint8_t len) sie_write(SIE_CMDCODE_ENDPOINT_SELECT+0, 0, 0); sie_write(SIE_CMDCODE_BUFFER_CLEAR , 0, 0); + usb_irq_unlock(lock); return len; } @@ -300,8 +364,9 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) uint8_t const epnum = tu_edpt_number(p_endpoint_desc->bEndpointAddress); uint8_t const ep_id = ep_addr2idx(p_endpoint_desc->bEndpointAddress); - // Endpoint type is fixed to endpoint number - // 1: interrupt, 2: Bulk, 3: Iso and so on + // Endpoint type is fixed to endpoint number (1 interrupt, 2 bulk, 3 iso, ...). + // Iso endpoints are armed via dcd_edpt_iso_alloc/activate, never through here + // (TUP_DCD_EDPT_ISO_ALLOC is defined for this IP), so only bulk/interrupt land here. switch ( p_endpoint_desc->bmAttributes.xfer ) { case TUSB_XFER_INTERRUPT: @@ -312,10 +377,6 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) TU_ASSERT((epnum % 3) == 2 || (epnum == 15)); break; - case TUSB_XFER_ISOCHRONOUS: - TU_ASSERT((epnum % 3) == 0 && (epnum != 0) && (epnum != 15)); - break; - default: break; } @@ -326,9 +387,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) //------------- first DD prepare -------------// dma_desc_t* const dd = &_dcd.dd[ep_id]; - tu_memclr(dd, sizeof(dma_desc_t)); - - dd->isochronous = (p_endpoint_desc->bmAttributes.xfer == TUSB_XFER_ISOCHRONOUS) ? 1 : 0; + tu_memclr(dd, sizeof(dma_desc_t)); // non-iso: isochronous stays 0 dd->max_packet_size = ep_size; dd->retired = 1; // invalid at first @@ -338,16 +397,54 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) } bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { +#if DCD_ISO_ENABLED (void)rhport; - (void)ep_addr; - (void)largest_packet_size; + uint8_t const ep_id = ep_addr2idx(ep_addr); + + // hardware fixes iso to endpoint numbers 3, 6, 9, 12 + TU_ASSERT(ep_id_is_iso(ep_id)); + TU_ASSERT(largest_packet_size > 0); + + set_ep_size(ep_id, largest_packet_size); + + dma_desc_t* const dd = &_dcd.dd[ep_id]; + tu_memclr(dd, sizeof(dma_desc_t)); + dd->isochronous = 1; + dd->max_packet_size = largest_packet_size; + dd->retired = 1; // invalid at first + + sie_write(SIE_CMDCODE_ENDPOINT_SET_STATUS + ep_id, 1, 0); + return true; +#else + (void)rhport; (void)ep_addr; (void)largest_packet_size; return false; +#endif } bool dcd_edpt_iso_activate(uint8_t rhport, const tusb_desc_endpoint_t *desc_ep) { +#if DCD_ISO_ENABLED (void)rhport; - (void)desc_ep; + uint8_t const ep_id = ep_addr2idx(desc_ep->bEndpointAddress); + dma_desc_t* const dd = &_dcd.dd[ep_id]; + + // same fixed-number rule as alloc: without it a rejected-but-ignored alloc (classes + // discard that return) would set isochronous on a non-iso ep_id and underflow iso_slot() + TU_ASSERT(ep_id_is_iso(ep_id)); + + // kill any armed transfer from a previous alternate setting + LPC_USB->EpDMADis = TU_BIT(ep_id); + _dcd.udca[ep_id] = NULL; + + dd->isochronous = 1; + dd->max_packet_size = tu_edpt_packet_size(desc_ep); + dd->retired = 1; + + sie_write(SIE_CMDCODE_ENDPOINT_SET_STATUS + ep_id, 1, 0); + return true; +#else + (void)rhport; (void)desc_ep; return false; +#endif } void dcd_edpt_close_all (uint8_t rhport) @@ -388,19 +485,28 @@ static bool control_xact(uint8_t rhport, uint8_t dir, uint8_t * buffer, uint8_t control_ep_write(buffer, len); }else { + // guard the out_received/out_buffer handshake against the EP0 OUT ISR + bool const lock = usb_irq_lock(); + if ( _dcd.control.out_received ) { // Already received the DATA OUT packet _dcd.control.out_received = false; - _dcd.control.out_buffer = NULL; - _dcd.control.out_bytes = 0; uint8_t received = control_ep_read(buffer, len); + // event queued with in_isr=true, which skips the queue's own locking: keep the + // USB IRQ masked across it, or a real ISR completion could interleave the write dcd_event_xfer_complete(0, 0, received, XFER_RESULT_SUCCESS, true); + usb_irq_unlock(lock); }else { + // buffer is NULL for a status-stage ZLP: signal the pending xfer explicitly, + // NOT via out_buffer != NULL — a NULL-buffer queue mistaken for "nothing queued" + // leaves out_received stale and poisons the next control OUT data stage. _dcd.control.out_buffer = buffer; _dcd.control.out_bytes = len; + _dcd.control.out_queued = true; + usb_irq_unlock(lock); } } @@ -425,26 +531,68 @@ bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t t uint16_t const ep_size = dd->max_packet_size; uint8_t is_iso = dd->isochronous; - tu_memclr(dd, sizeof(dma_desc_t)); - dd->isochronous = is_iso; - dd->max_packet_size = ep_size; - dd->buffer = (uint32_t) buffer; - dd->buflen = total_bytes; +#if DCD_ISO_ENABLED + if ( is_iso ) + { + // iso: buflen counts packets; per-packet sizes live in the packet-size memory. + // One packet moves per frame (UM10562 12.15.6: DMA request is raised for + // DMA-enabled iso endpoints on every FRAME interrupt, both directions). + // Validate BEFORE touching the DD: bailing out mid-rebuild would leave a + // zeroed (retired=0 -> serviceable) descriptor armed for the frame engine. + TU_ASSERT(ep_size > 0); + uint16_t const packets = (total_bytes > 0) ? (uint16_t) tu_div_ceil(total_bytes, ep_size) : 1; + TU_ASSERT(packets <= ISO_MAX_PACKETS); - _dcd.udca[ep_id] = dd; + uint8_t const slot = iso_slot(ep_id); + uint16_t remain = total_bytes; + for ( uint16_t i = 0; i < packets; i++ ) + { + uint16_t const pkt_len = tu_min16(remain, ep_size); + // IN: length to send (0 = ZLP). OUT: hardware writes back + // Frame_number|Packet_valid|Packet_length -- prefill 0 so a frame the + // hardware never wrote (missed/invalid) cannot read back as data. + _dcd.iso_psize[slot][i] = (ep_id & 1) ? pkt_len : 0; + remain = (uint16_t)(remain - pkt_len); + } - if ( ep_id % 2 ) - { - // Clear EP interrupt before Enable DMA - LPC_USB->EpIntEn &= ~TU_BIT(ep_id); - LPC_USB->EpDMAEn = TU_BIT(ep_id); + tu_memclr(dd, sizeof(dma_desc_t)); + dd->isochronous = 1; + dd->max_packet_size = ep_size; + dd->buffer = (uint32_t) buffer; + dd->buflen = packets; + dd->iso_packet_size_addr = (uint32_t) &_dcd.iso_psize[slot][0]; - // endpoint IN need to actively raise DMA request - LPC_USB->DMARSet = TU_BIT(ep_id); - }else + _dcd.udca[ep_id] = dd; + LPC_USB->EpDMAEn = TU_BIT(ep_id); // frame-triggered: no DMARSet, no EpIntEn + } + else +#else + (void) is_iso; +#endif { - // Enable DMA - LPC_USB->EpDMAEn = TU_BIT(ep_id); + tu_memclr(dd, sizeof(dma_desc_t)); + dd->max_packet_size = ep_size; + dd->buffer = (uint32_t) buffer; + dd->buflen = total_bytes; + + _dcd.udca[ep_id] = dd; + + if ( ep_id % 2 ) + { + // Clear EP interrupt before Enable DMA + // EpIntEn read-modify-write races the ISR's own RMWs -> lock + bool const lock = usb_irq_lock(); + LPC_USB->EpIntEn &= ~TU_BIT(ep_id); + LPC_USB->EpDMAEn = TU_BIT(ep_id); + usb_irq_unlock(lock); + + // endpoint IN need to actively raise DMA request + LPC_USB->DMARSet = TU_BIT(ep_id); + }else + { + // Enable DMA + LPC_USB->EpDMAEn = TU_BIT(ep_id); + } } return true; @@ -470,13 +618,20 @@ static void control_xfer_isr(uint8_t rhport, uint32_t ep_int_status) uint8_t setup_packet[8]; control_ep_read(setup_packet, 8); // TODO read before clear setup above + // a new SETUP voids any half-finished control state + _dcd.control.out_queued = false; + _dcd.control.out_received = false; + _dcd.control.out_buffer = NULL; + _dcd.control.out_bytes = 0; + dcd_event_setup_received(rhport, setup_packet, true); } - else if ( _dcd.control.out_buffer ) + else if ( _dcd.control.out_queued ) { - // software queued transfer previously + // software queued transfer previously (out_buffer NULL = status ZLP) uint8_t received = control_ep_read(_dcd.control.out_buffer, _dcd.control.out_bytes); + _dcd.control.out_queued = false; _dcd.control.out_buffer = NULL; _dcd.control.out_bytes = 0; @@ -532,7 +687,32 @@ static void dd_complete_isr(uint8_t rhport, uint8_t ep_id) uint8_t result = (dd->status == DD_STATUS_NORMAL || dd->status == DD_STATUS_DATA_UNDERUN) ? XFER_RESULT_SUCCESS : XFER_RESULT_FAILED; uint8_t const ep_addr = (ep_id / 2) | ((ep_id & 0x01) ? TUSB_DIR_IN_MASK : 0); - dcd_event_xfer_complete(rhport, ep_addr, dd->present_count, result, true); + uint32_t xferred_bytes; +#if DCD_ISO_ENABLED + if ( ep_id_is_iso(ep_id) ) + { + // present_count is in packets; actual byte counts are in the packet-size memory + // (IN: as programmed by us, OUT: Packet_length written back by hardware, + // guarded by Packet_valid -- a frame with no packet must count as 0) + uint8_t const slot = iso_slot(ep_id); + uint16_t const packets = tu_min16(dd->present_count, ISO_MAX_PACKETS); + xferred_bytes = 0; + for (uint16_t i = 0; i < packets; i++) + { + uint32_t const psize = _dcd.iso_psize[slot][i]; + if ( (ep_id & 1) || (psize & TU_BIT(16)) ) + { + xferred_bytes += (psize & 0xFFFFu); + } + } + } + else +#endif + { + xferred_bytes = dd->present_count; + } + + dcd_event_xfer_complete(rhport, ep_addr, (uint16_t) xferred_bytes, result, true); } // main USB IRQ handler @@ -588,6 +768,16 @@ void dcd_int_handler(uint8_t rhport) { if ( tu_bit_test(eot, ep_id) ) { + // dispatch on the hardware's fixed ep-number/type map, NOT dd->isochronous: + // thread-mode dcd_edpt_xfer transiently zeroes the DD while rebuilding it +#if DCD_ISO_ENABLED + if ( ep_id_is_iso(ep_id) ) + { + // iso: last packet already left with its frame; complete both directions here + dd_complete_isr(rhport, ep_id); + } + else +#endif if ( ep_id & 0x01 ) { // IN enable EpInt for end of usb transfer diff --git a/src/portable/nxp/lpc17_40/dcd_lpc17_40.h b/src/portable/nxp/lpc17_40/dcd_lpc17_40.h index 25c9f9985..da7f726d4 100644 --- a/src/portable/nxp/lpc17_40/dcd_lpc17_40.h +++ b/src/portable/nxp/lpc17_40/dcd_lpc17_40.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c b/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c index 8adf0f840..42f6750b1 100644 --- a/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c +++ b/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -106,6 +87,10 @@ enum { DEVCMDSTAT_SUSPEND_CHANGE_MASK = TU_BIT(25), DEVCMDSTAT_RESET_CHANGE_MASK = TU_BIT(26), DEVCMDSTAT_VBUS_DEBOUNCED_MASK = TU_BIT(28), + + // write-1-to-clear latches + DEVCMDSTAT_W1C_MASK = DEVCMDSTAT_SETUP_RECEIVED_MASK | DEVCMDSTAT_CONNECT_CHANGE_MASK | + DEVCMDSTAT_SUSPEND_CHANGE_MASK | DEVCMDSTAT_RESET_CHANGE_MASK, }; enum { @@ -177,6 +162,10 @@ typedef struct // - 55 usb0 (FS) has 5x2 endpoints, usb1 (HS) has 6x2 endpoints #define MAX_EP_PAIRS 6 +// Bounded spin waiting for hardware to clear an EPSKIP bit when retiring a still-armed endpoint on +// reopen (dcd_edpt_open). Hardware clears it within a (micro)frame; the guard only avoids a hang. +#define IP3511_EPSKIP_SPIN 100000u + // NOTE data will be transferred as soon as dcd get request by dcd_pipe(_queue)_xfer using double buffering. // current_td is used to keep track of number of remaining & xferred bytes of the current request. typedef struct @@ -186,7 +175,9 @@ typedef struct ep_cmd_sts_t ep[2*MAX_EP_PAIRS][2]; xfer_dma_t dma[2*MAX_EP_PAIRS]; - TU_ATTR_ALIGNED(64) uint8_t setup_packet[8]; + // volatile: the controller DMAs a new setup packet into this buffer as soon as the SETUP + // latch is cleared, so reads of it must stay ordered against the register accesses around them + TU_ATTR_ALIGNED(64) volatile uint8_t setup_packet[8]; }dcd_data_t; // EP list must be 256-byte aligned @@ -195,8 +186,12 @@ typedef struct // Use CFG_TUD_MEM_SECTION to place it accordingly. CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(256) static dcd_data_t _dcd; -// Dummy buffer to fix ZLPs overwriting the buffer (probably an USB/DMA controller bug) -// TODO find way to save memory +// Dummy buffer to fix ZLPs overwriting the buffer: Errata LPC55S6x USB.5 / LPC55S2x USB.4 - the +// HS device controller always DMA-writes OUT data in 8-byte units, so up to 7 bytes land past the +// received length. This redirects the ZLP case; the general short-OUT case is unhandled here +// (TinyUSB's own endpoint buffers are sized/aligned so the spill stays inside them, but a tight +// caller buffer can be overrun by up to 7 bytes - the SDK's documented workaround is a bounce +// buffer). TODO find way to save memory CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(64) static uint8_t dummy[8]; //--------------------------------------------------------------------+ @@ -236,7 +231,7 @@ static const dcd_controller_t _dcd_controller[] = { // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -TU_ATTR_ALWAYS_INLINE static inline uint16_t get_buf_offset(void const * buffer) { +TU_ATTR_ALWAYS_INLINE static inline uint16_t get_buf_offset(void const volatile * buffer) { uint32_t addr = (uint32_t) buffer; TU_ASSERT( (addr & 0x3f) == 0, 0 ); return ( (addr >> 6) & 0xFFFFUL ) ; @@ -262,6 +257,16 @@ TU_ATTR_ALWAYS_INLINE static inline bool rhport_is_highspeed(uint8_t rhport) { return _dcd_controller[rhport].is_highspeed; } + +// DEVCMDSTAT mixes RW fields with write-1-to-clear latches (SETUP + the 3 change bits): a blind +// RMW writes a pending latch back as 1 and silently clears it (a SETUP eaten this way strands +// EP0). Mask the latches on every update; pass one in set_mask only to clear it. +TU_ATTR_ALWAYS_INLINE static inline void devcmdstat_update(dcd_registers_t* dcd_reg, + uint32_t clear_mask, uint32_t set_mask) { + const uint32_t v = dcd_reg->DEVCMDSTAT & ~(DEVCMDSTAT_W1C_MASK | clear_mask); + dcd_reg->DEVCMDSTAT = v | set_mask; +} + //--------------------------------------------------------------------+ // CONTROLLER API //--------------------------------------------------------------------+ @@ -299,8 +304,10 @@ bool dcd_init(uint8_t rhport, const tusb_rhport_init_t* rh_init) { dcd_reg->DATABUFSTART = tu_align((uint32_t) &_dcd, TU_BIT(22)); // 22-bit alignment dcd_reg->INTSTAT = dcd_reg->INTSTAT; // clear all pending interrupt dcd_reg->INTEN = INT_DEVICE_STATUS_MASK; - dcd_reg->DEVCMDSTAT |= DEVCMDSTAT_DEVICE_ENABLE_MASK | DEVCMDSTAT_DEVICE_CONNECT_MASK | - DEVCMDSTAT_RESET_CHANGE_MASK | DEVCMDSTAT_CONNECT_CHANGE_MASK | DEVCMDSTAT_SUSPEND_CHANGE_MASK; + // deliberately clear every latch (incl. a SETUP left by a bootloader/warm start) for a + // deterministic init state + devcmdstat_update(dcd_reg, 0, DEVCMDSTAT_DEVICE_ENABLE_MASK | DEVCMDSTAT_DEVICE_CONNECT_MASK | + DEVCMDSTAT_W1C_MASK); NVIC_ClearPendingIRQ(_dcd_controller[rhport].irqnum); @@ -324,8 +331,7 @@ void dcd_set_address(uint8_t rhport, uint8_t dev_addr) // Response with status first before changing device address dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_IN), NULL, 0, false); - dcd_reg->DEVCMDSTAT &= ~DEVCMDSTAT_DEVICE_ADDR_MASK; - dcd_reg->DEVCMDSTAT |= dev_addr; + devcmdstat_update(dcd_reg, DEVCMDSTAT_DEVICE_ADDR_MASK, dev_addr); } void dcd_remote_wakeup(uint8_t rhport) @@ -336,13 +342,13 @@ void dcd_remote_wakeup(uint8_t rhport) void dcd_connect(uint8_t rhport) { dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_reg->DEVCMDSTAT |= DEVCMDSTAT_DEVICE_CONNECT_MASK; + devcmdstat_update(dcd_reg, 0, DEVCMDSTAT_DEVICE_CONNECT_MASK); } void dcd_disconnect(uint8_t rhport) { dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_reg->DEVCMDSTAT &= ~DEVCMDSTAT_DEVICE_CONNECT_MASK; + devcmdstat_update(dcd_reg, DEVCMDSTAT_DEVICE_CONNECT_MASK, 0); } void dcd_sof_enable(uint8_t rhport, bool en) @@ -356,13 +362,37 @@ void dcd_sof_enable(uint8_t rhport, bool en) //--------------------------------------------------------------------+ // DCD Endpoint Port //--------------------------------------------------------------------+ +// Retire a still-armed (Active) endpoint before reconfiguring it (reopen across SET_INTERFACE). +// UM11126 §41.7.6/§41.8.3: write EPSKIP and wait for hardware to clear the bit, then Active is +// safe to clear. EPSKIP raises the endpoint interrupt as it clears Active, delivered as a +// (partial) transfer completion. Here that is sanctioned — usbd_edpt_close() documents "in +// progress transfers may be delivered after this call", and that completion is what clears the +// stale usbd busy flag (ISO_ALLOC close is a no-op) so the class can re-arm the reopened +// endpoint. NOT for the stall/iso-activate paths: there the class re-arms from the completion +// callback and the endpoint ends up Active+Stall, which never sends a STALL handshake (usbtest +// case 13 regression on LPC11u37) — those paths must clear Active directly instead. +// Bounded: hardware clears EPSKIP within a (micro)frame. +static void edpt_skip_active(uint8_t rhport, uint8_t ep_id) { + ep_cmd_sts_t* ep_cs = get_ep_cs(ep_id); + if ( ep_cs[0].cmd_sts.active || ep_cs[1].cmd_sts.active ) { + dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; + dcd_reg->EPSKIP |= TU_BIT(ep_id); + uint32_t guard = IP3511_EPSKIP_SPIN; + while ( (dcd_reg->EPSKIP & TU_BIT(ep_id)) && guard-- ) {} + } + ep_cs[0].cmd_sts.active = ep_cs[1].cmd_sts.active = 0; +} + void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { (void) rhport; - // TODO cannot able to STALL Control OUT endpoint !!!!! FIXME try some walk-around uint8_t const ep_id = ep_addr2id(ep_addr); - _dcd.ep[ep_id][0].cmd_sts.stall = 1; + // Clear Active directly before setting Stall (no EPSKIP — see edpt_skip_active): the hardware + // services an armed buffer instead of returning STALL, so a halt requested while a transfer is + // queued would not actually stall the endpoint (usbtest case 13). + _dcd.ep[ep_id][0].cmd_sts.active = 0; + _dcd.ep[ep_id][0].cmd_sts.stall = 1; } void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) @@ -371,9 +401,17 @@ void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) uint8_t const ep_id = ep_addr2id(ep_addr); + // Preserve rf_tv: for non-control endpoints it is a TYPE bit, not the toggle value (UM11126: + // T=1 + RF 1/0 = interrupt/iso). Zeroing it here turned HS periodic interrupt endpoints into + // isochronous - no handshake on OUT, dead IN (usbtest cases 25/26 on lpc55 HS port). + // TODO implement the Errata LPC546xx USB.13 work-around (same semantics in UM11126): with RF/TV preserved at 1, TR + // loads the toggle from TV, so an HS interrupt endpoint restarts on DATA1 after clear-halt and + // the host discards one packet as a retransmission. The documented workaround needs an + // interrupt-on-NAK state machine (park as generic TR=1/TV=0, wait for a NAKed token to latch + // toggle 0 via EPTOGGLE, restore the type) - deferred; one lost packet beats the fully broken + // endpoint the old rf_tv clear caused. _dcd.ep[ep_id][0].cmd_sts.stall = 0; _dcd.ep[ep_id][0].cmd_sts.toggle_reset = 1; - _dcd.ep[ep_id][0].cmd_sts.rf_tv = 0; } bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) @@ -381,9 +419,15 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) //------------- Prepare Queue Head -------------// uint8_t ep_id = ep_addr2id(p_endpoint_desc->bEndpointAddress); ep_cmd_sts_t* ep_cs = get_ep_cs(ep_id); + dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - // Check if endpoint is available - TU_ASSERT( ep_cs[0].cmd_sts.disable && ep_cs[1].cmd_sts.disable ); + // usbd_edpt_close() is a no-op on ISO_ALLOC ports, so an endpoint a class closed then reopened + // across SET_INTERFACE (e.g. the video notification or audio streaming endpoint) is still armed + // here rather than disabled. Retire it (edpt_skip_active) before reconfiguring. + if ( !(ep_cs[0].cmd_sts.disable && ep_cs[1].cmd_sts.disable) ) { + edpt_skip_active(rhport, ep_id); + ep_cs[0].cmd_sts.disable = ep_cs[1].cmd_sts.disable = 1; + } edpt_reset(rhport, ep_id); @@ -408,7 +452,6 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) } // Enable EP interrupt - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; dcd_reg->INTEN |= TU_BIT(ep_id); return true; @@ -418,34 +461,40 @@ void dcd_edpt_close_all (uint8_t rhport) { for (uint8_t ep_id = 0; ep_id < 2*_dcd_controller[rhport].ep_pairs; ++ep_id) { - _dcd.ep[ep_id][0].cmd_sts.active = _dcd.ep[ep_id][0].cmd_sts.active = 0; // TODO proper way is to EPSKIP then wait ep[][].active then write ep[][].disable (see table 778 in LPC55S69 Use Manual) + _dcd.ep[ep_id][0].cmd_sts.active = _dcd.ep[ep_id][1].cmd_sts.active = 0; // TODO proper way is to EPSKIP then wait ep[][].active then write ep[][].disable (see table 778 in LPC55S69 Use Manual) _dcd.ep[ep_id][0].cmd_sts.disable = _dcd.ep[ep_id][1].cmd_sts.disable = 1; } } -void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) -{ - (void) rhport; - +bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { + (void) largest_packet_size; + // Reserve the endpoint command/status entry once (persists across altsetting changes); the + // buffer pointer is filled per-transfer, so nothing to pre-allocate. Mirrors the ISO branch of + // dcd_edpt_open(). uint8_t ep_id = ep_addr2id(ep_addr); - _dcd.ep[ep_id][0].cmd_sts.active = _dcd.ep[ep_id][0].cmd_sts.active = 0; // TODO proper way is to EPSKIP then wait ep[][].active then write ep[][].disable (see table 778 in LPC55S69 Use Manual) - _dcd.ep[ep_id][0].cmd_sts.disable = _dcd.ep[ep_id][1].cmd_sts.disable = 1; -} + ep_cmd_sts_t* ep_cs = get_ep_cs(ep_id); + TU_ASSERT( ep_cs[0].cmd_sts.disable && ep_cs[1].cmd_sts.disable ); -#if 0 -bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { - (void)rhport; - (void)ep_addr; - (void)largest_packet_size; - return false; + edpt_reset(rhport, ep_id); + ep_cs[0].cmd_sts.type = 1; // ISO + + dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; + dcd_reg->INTEN |= TU_BIT(ep_id); + return true; } bool dcd_edpt_iso_activate(uint8_t rhport, const tusb_desc_endpoint_t *desc_ep) { - (void)rhport; - (void)desc_ep; - return false; + // (Re)activate on altsetting selection: abort a transfer still armed from the previous + // altsetting (the hardware keeps servicing an Active buffer across SET_INTERFACE, fighting the + // fresh transfer the class queues), clear stall and reset the data toggle. Direct Active=0, not + // EPSKIP (see edpt_skip_active). The class re-arms via dcd_edpt_xfer(). + uint8_t ep_id = ep_addr2id(desc_ep->bEndpointAddress); + ep_cmd_sts_t* ep_cs = get_ep_cs(ep_id); + ep_cs[0].cmd_sts.active = 0; + ep_cs[1].cmd_sts.active = 0; + dcd_edpt_clear_stall(rhport, desc_ep->bEndpointAddress); + return true; } -#endif static void prepare_ep_xfer(uint8_t rhport, uint8_t ep_id, uint16_t buf_offset, uint16_t total_bytes) { uint16_t nbytes; @@ -518,7 +567,7 @@ static void bus_reset(uint8_t rhport) dcd_reg->EPSKIP = 0xFFFFFFFF; dcd_reg->INTSTAT = dcd_reg->INTSTAT; // clear all pending interrupt - dcd_reg->DEVCMDSTAT |= DEVCMDSTAT_SETUP_RECEIVED_MASK; // clear setup received interrupt + devcmdstat_update(dcd_reg, 0, DEVCMDSTAT_SETUP_RECEIVED_MASK); // clear setup received interrupt dcd_reg->INTEN = INT_DEVICE_STATUS_MASK | TU_BIT(0) | TU_BIT(1); // enable device status & control endpoints } @@ -577,18 +626,25 @@ void dcd_int_handler(uint8_t rhport) { dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - uint32_t const cmd_stat = dcd_reg->DEVCMDSTAT; - uint32_t int_status = dcd_reg->INTSTAT; - int_status &= dcd_reg->INTEN; + int_status &= dcd_reg->INTEN; dcd_reg->INTSTAT = int_status; // Acknowledge handled interrupt if (int_status == 0) return; + // Snapshot after the INTSTAT ack: latch bits persist (RWC) so nothing is lost, while the reverse + // order could consume INTSTAT bit0 for a SETUP not yet visible in the snapshot - stranding the + // SETUP (INTSTAT is edge-latched) and feeding bit0 to process_xfer_isr as a bogus completion. + uint32_t const cmd_stat = dcd_reg->DEVCMDSTAT; + //------------- Device Status -------------// if ( int_status & INT_DEVICE_STATUS_MASK ) { - dcd_reg->DEVCMDSTAT |= DEVCMDSTAT_RESET_CHANGE_MASK | DEVCMDSTAT_CONNECT_CHANGE_MASK | DEVCMDSTAT_SUSPEND_CHANGE_MASK; + // clear only the change latches observed in the snapshot: one latched by hardware between the + // snapshot and this write would be acknowledged unseen (its DEV_INT re-latches and dispatches + // next pass instead) + devcmdstat_update(dcd_reg, 0, cmd_stat & + (DEVCMDSTAT_RESET_CHANGE_MASK | DEVCMDSTAT_CONNECT_CHANGE_MASK | DEVCMDSTAT_SUSPEND_CHANGE_MASK)); if ( cmd_stat & DEVCMDSTAT_RESET_CHANGE_MASK) // bus reset { @@ -633,15 +689,43 @@ void dcd_int_handler(uint8_t rhport) _dcd.ep[0][0].cmd_sts.active = _dcd.ep[1][0].cmd_sts.active = 0; _dcd.ep[0][0].cmd_sts.stall = _dcd.ep[1][0].cmd_sts.stall = 0; - dcd_reg->DEVCMDSTAT |= DEVCMDSTAT_SETUP_RECEIVED_MASK; + // UM flow: ack the latch FIRST, then read the payload. This IP has no setup lockout, so a + // back-to-back SETUP can overwrite _dcd.setup_packet at any time - but with the latch already + // released, any such overwrite re-latches SETUP_RECEIVED and is redelivered (worst case a + // superseded duplicate, absorbed by usbd's queued-setup counter). The reverse order can + // consume the newer SETUP's latch unseen and lose it. + devcmdstat_update(dcd_reg, 0, DEVCMDSTAT_SETUP_RECEIVED_MASK); + + // UM11126 Fig 163 (control EP0 flowchart) requires clearing the EP0IN interrupt here: a + // control IN completion latched before this SETUP must not reach usbd after it, where it + // would be applied to the new request and arm its status stage early. EP0OUT goes with it - + // bit0 is set by SETUP reception too, and left set it would replay next pass as a phantom + // completion. Neither can discard live work: the SETUP latch NAKs all EP0 traffic until the + // update above, and both EP0 Active bits were cleared a few lines up. + dcd_reg->INTSTAT = TU_BIT(0) | TU_BIT(1); - dcd_event_setup_received(rhport, _dcd.setup_packet, true); + // Copied a byte at a time rather than with memcpy: C orders volatile accesses only against + // each other, so a non-volatile copy of this buffer may be sunk below the guard read that + // follows - gcc does exactly that at -O2 and -O3, leaving only -Os correct. + uint8_t setup_copy[8]; + for (uint8_t i = 0; i < sizeof(setup_copy); i++) { + setup_copy[i] = _dcd.setup_packet[i]; + } + + // a SETUP that raced in after the acks (its bit0 consumed above) makes this copy suspect: + // its latch is visible again, so re-raise the endpoint interrupt and let the next pass + // deliver the newer payload rather than passing up bytes that may be torn between the two + if (dcd_reg->DEVCMDSTAT & DEVCMDSTAT_SETUP_RECEIVED_MASK) { + dcd_reg->INTSETSTAT = TU_BIT(0); + } else { + dcd_event_setup_received(rhport, setup_copy, true); + } // keep waiting for next setup prepare_setup_packet(rhport); - // clear bit0 - int_status = tu_bit_clear(int_status, 0); + // drop both EP0 bits: acked above, and neither belongs to the request this SETUP starts + int_status &= ~(TU_BIT(0) | TU_BIT(1)); } // Endpoint transfer complete interrupt diff --git a/src/portable/nxp/lpc_ip3516/hcd_lpc_ip3516.c b/src/portable/nxp/lpc_ip3516/hcd_lpc_ip3516.c index c9810f51c..b9ad172c5 100644 --- a/src/portable/nxp/lpc_ip3516/hcd_lpc_ip3516.c +++ b/src/portable/nxp/lpc_ip3516/hcd_lpc_ip3516.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2025 HiFiPhile (Zixun LI) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2025 HiFiPhile (Zixun LI) + * SPDX-FileCopyrightText: Copyright (c) 2025 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/nxp/lpc_ip3516/hcd_lpc_ip3516.h b/src/portable/nxp/lpc_ip3516/hcd_lpc_ip3516.h index 5214c18ae..2b8758a9e 100644 --- a/src/portable/nxp/lpc_ip3516/hcd_lpc_ip3516.h +++ b/src/portable/nxp/lpc_ip3516/hcd_lpc_ip3516.h @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2025 HiFiPhile (Zixun LI) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2025 HiFiPhile (Zixun LI) + * SPDX-FileCopyrightText: Copyright (c) 2025 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/ohci/ohci.c b/src/portable/ohci/ohci.c index 4b248d9e6..2a174e46c 100644 --- a/src/portable/ohci/ohci.c +++ b/src/portable/ohci/ohci.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -397,7 +378,7 @@ static void ed_list_remove_by_addr(ohci_ed_t * p_head, uint8_t dev_addr) { ohci_ed_t* p_prev = p_head; while (p_prev->next) { - ohci_ed_t* ed = (ohci_ed_t*)_virt_addr((void*)p_prev->next); + ohci_ed_t* ed = hcd_dcache_uncached((ohci_ed_t*)_virt_addr((void*)p_prev->next)); if (ed->w0.dev_addr == dev_addr) { // Prevent Host Controller from processing this ED while we remove it @@ -406,12 +387,28 @@ static void ed_list_remove_by_addr(ohci_ed_t * p_head, uint8_t dev_addr) { // unlink ed, will also move up p_prev p_prev->next = ed->next; - // point the removed ED's next pointer to list head to make sure HC can always safely move away from this ED - ed->next = (uint32_t)_phys_addr(p_head); - ed->w0.used = 0; - ed->w0.skip = 0; + // Control endpoints (EP number 0) are statically allocated with the device which are only reused + // after connection of another device long after HC has finished with them now, these can be freed immediately. + if (ed->w0.ep_number != 0) { + // Wait until the next frame before reclaiming the ED and its TDs. Set the deadline before + // publishing is_reclaiming so a pending SOF IRQ cannot use an older deadline for this ED. + ohci_data.reclaim_frame = (uint16_t)(OHCI_REG->frame_number + 1); + ed->w0.is_reclaiming = 1; + + // 5.2.7.1.2 Removing. Disable list processing for bulk + if (p_head == p_ed_head[TUSB_XFER_BULK]) { + OHCI_REG->control &= ~OHCI_CONTROL_LIST_BULK_ENABLE_MASK; + } + + // Temporarily enable SOF IRQ. Clear any pending SOF first to wait for the next frame. + OHCI_REG->interrupt_status = OHCI_INT_SOF_MASK; + OHCI_REG->interrupt_enable = OHCI_INT_SOF_MASK; + } else { + ed->w0.used = 0; + ed->w0.skip = 0; + } } else { - p_prev = (ohci_ed_t*)_virt_addr((void*)p_prev->next); + p_prev = ed; } } } @@ -419,6 +416,7 @@ static void ed_list_remove_by_addr(ohci_ed_t * p_head, uint8_t dev_addr) { static ohci_gtd_t* gtd_find_free(void) { for (uint8_t i = 0; i < GTD_MAX; i++) { if (!ohci_data.gtd_pool[i].used) { + ohci_data.gtd_pool[i].used = 1; return &ohci_data.gtd_pool[i]; } } @@ -671,6 +669,60 @@ void hcd_int_handler(uint8_t hostid, bool in_isr) { // Disable MIE as per OHCI spec 5.3 OHCI_REG->interrupt_disable = OHCI_INT_MASTER_ENABLE_MASK; + // Start of frame (SOF). Signed subtraction handles frame number rollover and delayed interrupts. + if ((int_status & OHCI_INT_SOF_MASK) && + ((int16_t)((uint16_t)OHCI_REG->frame_number - ohci_data.reclaim_frame) >= 0)) { + OHCI_REG->interrupt_disable = OHCI_INT_SOF_MASK; + + bool re_enable_lists = false; + + for (size_t i = 0; i < ED_MAX; i++) { + ohci_ed_t* ed = hcd_dcache_uncached(&ohci_data.ed_pool[i]); + if (ed->w0.used && ed->w0.is_reclaiming) { + TU_ASSERT(ed->w0.skip == 1, ); + TU_ASSERT(ed->w0.ep_number != 0, ); + + // Reclaim orphaned TDs + uint32_t td_addr = ed->td_head.address & ~0x0F; + while (td_addr) { + if (!ed->w0.is_iso) { + ohci_gtd_t *gtd = (ohci_gtd_t*)_virt_addr((void*)(uintptr_t)td_addr); + gtd->used = 0; + } else { + // TODO: Free ITD once implemented + } + + if (td_addr == ed->td_tail) { + break; + } + td_addr = ((ohci_td_item_t*)_virt_addr((void*)(uintptr_t)td_addr))->next; + } + + ed->w0.is_reclaiming = 0; + ed->w0.used = 0; + ed->w0.skip = 0; + + re_enable_lists = true; + } + } + + if (re_enable_lists) { + // 5.2.7.1.2 Removing + // Reset current ED pointers and re-enable lists + // Once the next frame has started, the HcControlCurrentED or HcBulkCurrentED register should be adjusted so + // that it does not point to the Endpoint Descriptor being removed (for simplicity you may just write + // a zero to the register); + if (!(OHCI_REG->control & OHCI_CONTROL_LIST_CONTROL_ENABLE_MASK)) { + OHCI_REG->control_current_ed = 0; + OHCI_REG->control |= OHCI_CONTROL_LIST_CONTROL_ENABLE_MASK; + } + if (!(OHCI_REG->control & OHCI_CONTROL_LIST_BULK_ENABLE_MASK)) { + OHCI_REG->bulk_current_ed = 0; + OHCI_REG->control |= OHCI_CONTROL_LIST_BULK_ENABLE_MASK; + } + } + } + // Frame number overflow if (int_status & OHCI_INT_FRAME_OVERFLOW_MASK) { ohci_data.frame_number_hi++; diff --git a/src/portable/ohci/ohci.h b/src/portable/ohci/ohci.h index d9ebe1d54..e28c6404f 100644 --- a/src/portable/ohci/ohci.h +++ b/src/portable/ohci/ohci.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -126,7 +107,8 @@ typedef union { // HCD: make use of 5 reserved bits uint32_t used : 1; uint32_t is_interrupt_xfer : 1; - uint32_t : 3; + uint32_t is_reclaiming : 1; + uint32_t : 2; }; uint32_t value; } ohci_ed_word0_t; @@ -201,6 +183,7 @@ typedef struct TU_ATTR_ALIGNED(256) { gtd_extra_data_t gtd_extra[GTD_MAX]; volatile uint16_t frame_number_hi; + volatile uint16_t reclaim_frame; } ohci_data_t; //--------------------------------------------------------------------+ diff --git a/src/portable/ohci/ohci_nxp.h b/src/portable/ohci/ohci_nxp.h index 9cba05e95..de06e4569 100644 --- a/src/portable/ohci/ohci_nxp.h +++ b/src/portable/ohci/ohci_nxp.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2025 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2025 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/raspberrypi/pio_usb/dcd_pio_usb.c b/src/portable/raspberrypi/pio_usb/dcd_pio_usb.c index 78df2b6a6..2830c0f63 100644 --- a/src/portable/raspberrypi/pio_usb/dcd_pio_usb.c +++ b/src/portable/raspberrypi/pio_usb/dcd_pio_usb.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2018, hathach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2018, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c index 90eb920e0..8a7722fb0 100644 --- a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c +++ b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/raspberrypi/rp2040/dcd_rp2040.c b/src/portable/raspberrypi/rp2040/dcd_rp2040.c index 2b6bbc43b..564ded535 100644 --- a/src/portable/raspberrypi/rp2040/dcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/dcd_rp2040.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2020 Raspberry Pi (Trading) Ltd. - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2020 Raspberry Pi (Trading) Ltd. + * SPDX-FileCopyrightText: Copyright (c) 2020 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -405,6 +387,9 @@ bool dcd_deinit(uint8_t rhport) { reset_block(RESETS_RESET_USBCTRL_BITS); unreset_block_wait(RESETS_RESET_USBCTRL_BITS); + // Release allocated resources + rp2usb_deinit(); + return true; } @@ -568,9 +553,46 @@ void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { if (epnum != 0) { struct hw_endpoint* ep = hw_endpoint_get(epnum, dir); - ep->next_pid = 0; // reset data toggle - io_rw_32 *buf_reg = get_buf_ctrl(epnum, dir); - *buf_reg = 0; + + if (ep->state == EPSTATE_ACTIVE) { + // Clear-halt on an endpoint with an in-flight transfer is used as a data-toggle reset + // (e.g. usbtest case 29) rather than to recover from a real stall (a stall aborts the + // transfer, leaving the endpoint IDLE). Abort and re-issue the transfer with the toggle + // reset to DATA0 so it still completes and releases the usbd claim, instead of silently + // dropping it and starving the endpoint. Save the buffer/length before the abort clears them. + uint8_t* user_buf = ep->user_buf; + uint16_t remaining = ep->remaining_len; + const uint16_t xferred = ep->xferred_len; // bytes already moved on this submission + io_rw_32 *ep_reg = get_ep_ctrl(epnum, dir); + io_rw_32 *buf_reg = get_buf_ctrl(epnum, dir); + // bufctrl_prepare16() subtracts each armed buffer's length from remaining_len when arming, + // for BOTH directions, before the host has drained (IN) or filled (OUT) it. The abort below + // discards those still-armed buffers, so rewind remaining_len by their lengths or the re-issue + // is short by 1-2 packets. IN additionally advances user_buf as packets are copied into DPRAM, + // so its pointer must rewind too; OUT copies out only on completion, so its pointer is intact. + const uint32_t bc = *buf_reg; + uint16_t staged = 0; + if (bc & USB_BUF_CTRL_AVAIL) { + staged = (uint16_t)(bc & USB_BUF_CTRL_LEN_MASK); + } + if ((bc >> 16) & USB_BUF_CTRL_AVAIL) { + staged = (uint16_t)(staged + ((bc >> 16) & USB_BUF_CTRL_LEN_MASK)); + } + remaining = (uint16_t)(remaining + staged); + if (dir == TUSB_DIR_IN) { + user_buf -= staged; + } + hw_endpoint_abort_xfer(ep); // safe abort (handles RP2040-E2), resets ep transfer state + ep->next_pid = 0; // DATA0 + rp2usb_xfer_start(ep, ep_reg, buf_reg, user_buf, NULL, remaining); + // rp2usb_xfer_start() zeroes xferred_len; add back what the aborted transfer already moved so + // the eventual completion reports the full length, not just the post-clear-halt remainder. + ep->xferred_len += xferred; + } else { + ep->next_pid = 0; // reset data toggle + io_rw_32 *buf_reg = get_buf_ctrl(epnum, dir); + *buf_reg = 0; // clear the stall response + } } } diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 064834efb..a04890835 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -1,27 +1,7 @@ - /* - * The MIT License (MIT) - * - * Copyright (c) 2020 Raspberry Pi (Trading) Ltd. - * Copyright (c) 2021 Ha Thach (tinyusb.org) for Double Buffered - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2020 Raspberry Pi (Trading) Ltd. + * SPDX-FileCopyrightText: Copyright (c) 2021 Ha Thach (tinyusb.org) for Double Buffered + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -447,6 +427,10 @@ bool hcd_deinit(uint8_t rhport) { irq_remove_handler(USBCTRL_IRQ, hcd_rp2040_irq); reset_block(RESETS_RESET_USBCTRL_BITS); unreset_block_wait(RESETS_RESET_USBCTRL_BITS); + + // Release allocated resources + rp2usb_deinit(); + return true; } diff --git a/src/portable/raspberrypi/rp2040/rp2040_usb.c b/src/portable/raspberrypi/rp2040/rp2040_usb.c index 83ac48ec2..96b335bd3 100644 --- a/src/portable/raspberrypi/rp2040/rp2040_usb.c +++ b/src/portable/raspberrypi/rp2040/rp2040_usb.c @@ -1,26 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2020 Raspberry Pi (Trading) Ltd. - * Copyright (c) 2021 Ha Thach (tinyusb.org) for Double Buffered - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2020 Raspberry Pi (Trading) Ltd. + * SPDX-FileCopyrightText: Copyright (c) 2021 Ha Thach (tinyusb.org) for Double Buffered + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -104,6 +85,10 @@ void rp2usb_init(void) { critical_section_init(&rp2usb_lock); } +void rp2usb_deinit(void) { + critical_section_deinit(&rp2usb_lock); +} + void __tusb_irq_path_func(rp2usb_reset_transfer)(hw_endpoint_t *ep) { ep->state = EPSTATE_IDLE; ep->remaining_len = 0; @@ -195,10 +180,15 @@ void __tusb_irq_path_func(rp2usb_buffer_start)(hw_endpoint_t *ep, io_rw_32 *ep_r // Note: device EP0 does not have an endpoint control register if (ep_reg != NULL) { uint32_t ep_ctrl = *ep_reg; + // Isochronous endpoints get a single DPRAM buffer (hw_endpoint_open only double-sizes BULK), so + // they must never be double-buffered here even when a transfer spans multiple packets, or buffer + // 1 (at dpram_buf+64) would spill into the next endpoint's DPRAM. (Never true for BULK, so the + // double-buffered bulk path is unaffected.) + const bool is_iso = (((ep_ctrl >> EP_CTRL_BUFFER_TYPE_LSB) & 0x3u) == TUSB_XFER_ISOCHRONOUS); #if CFG_TUH_ENABLED - const bool force_single = (rp2usb_is_host_mode() && ep->interrupt_num > 0); + const bool force_single = is_iso || (rp2usb_is_host_mode() && ep->interrupt_num > 0); #else - const bool force_single = false; + const bool force_single = is_iso; #endif if (ep->remaining_len && !force_single) { diff --git a/src/portable/raspberrypi/rp2040/rp2040_usb.h b/src/portable/raspberrypi/rp2040/rp2040_usb.h index 8ebc3e3fc..e5a54007c 100644 --- a/src/portable/raspberrypi/rp2040/rp2040_usb.h +++ b/src/portable/raspberrypi/rp2040/rp2040_usb.h @@ -1,3 +1,11 @@ +/* + * SPDX-FileCopyrightText: Copyright (c) 2020 Raspberry Pi (Trading) Ltd. + * SPDX-FileCopyrightText: Copyright (c) 2020 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT + * + * This file is part of the TinyUSB stack. + */ + #ifndef RP2040_COMMON_H_ #define RP2040_COMMON_H_ @@ -139,6 +147,7 @@ extern volatile uint32_t e15_last_sof; #endif void rp2usb_init(void); +void rp2usb_deinit(void); // if usb hardware is in host mode TU_ATTR_ALWAYS_INLINE static inline bool rp2usb_is_host_mode(void) { diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index adbb53787..c93bab05e 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -1,26 +1,8 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2020 Koji Kitayama - * Portions copyrighted (c) 2021 Roland Winistoerfer - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2020 Koji Kitayama + * SPDX-FileCopyrightText: Portions copyrighted (c) 2021 Roland Winistoerfer + * SPDX-FileCopyrightText: Copyright (c) 2020 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -46,6 +28,9 @@ typedef struct { uint8_t ep; /* an assigned endpoint address */ uint8_t ff; /* `buf` is TU_FUFO or POD */ + bool queued; /* a transfer is submitted and not yet completed (independent of `buf`, which is + NULL for a zero-length read) -- used to decide clear-stall re-arm */ + bool zlp_pending; /* a zero-length IN packet couldn't be queued at submit (FIFO full); retry on BRDY */ } pipe_state_t; typedef struct @@ -58,6 +43,7 @@ typedef struct static dcd_data_t _dcd; + //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ @@ -139,9 +125,19 @@ static uint16_t edpt_max_packet_size(rusb2_reg_t *rusb, unsigned num) { return rusb->PIPEMAXP; } -static inline void pipe_wait_for_ready(rusb2_reg_t * rusb, unsigned num) { - while ( rusb->D0FIFOSEL_b.CURPIPE != num ) {} - while ( !rusb->D0FIFOCTR_b.FRDY ) {} +// Select the D0FIFO for `num` and wait until its buffer is ready for CPU access. Both flags +// normally settle within a few cycles (the pipe was just armed, or a BRDY freed a plane). But an +// IN pipe whose double buffer is already full stalls FRDY until the host drains it, and a +// no-handshake iso IN endpoint the host has stopped polling never drains at all — so FRDY would +// hang forever. This runs with the USB IRQ masked, so a naked spin freezes the whole stack; bound +// it and let the caller abort the FIFO access. Returns false on timeout. +#define RUSB2_FIFO_READY_SPIN 100000u +static inline bool pipe_wait_for_ready(rusb2_reg_t *rusb, unsigned num) { + uint32_t spin = RUSB2_FIFO_READY_SPIN; + while ( rusb->D0FIFOSEL_b.CURPIPE != num ) { if (!spin--) return false; } + spin = RUSB2_FIFO_READY_SPIN; + while ( !rusb->D0FIFOCTR_b.FRDY ) { if (!spin--) return false; } + return true; } //--------------------------------------------------------------------+ @@ -195,6 +191,15 @@ static bool pipe0_xfer_out(rusb2_reg_t *rusb) { pipe_state_t *pipe = &_dcd.pipe[0]; const unsigned rem = pipe->remaining; + // BRDY with no armed transfer: a back-to-back data-stage packet beat the PID=NAK below (the + // host has already ACKed it). Park it in the DCP buffer — an unread buffer NAKs further OUTs — + // and let process_pipe0_xfer deliver it when usbd arms the next chunk. BCLR here would silently + // drop the packet and shift every later chunk by one (usbtest ctrl_out corruption at ra4m1). + if (pipe->buf == NULL && rem == 0) { + rusb->DCPCTR = RUSB2_PIPE_CTR_PID_NAK; + return false; + } + const uint16_t mps = edpt0_max_packet_size(rusb); const uint16_t vld = rusb->CFIFOCTR_b.DTLN; const uint16_t len = tu_min16(tu_min16(rem, mps), vld); @@ -219,6 +224,12 @@ static bool pipe0_xfer_out(rusb2_reg_t *rusb) { pipe->remaining = rem - len; if ((len < mps) || (rem == len)) { pipe->buf = NULL; + // Flow-control the single-buffer control pipe: NAK further OUT until usbd arms the next + // data-stage chunk. usbd receives a multi-packet control-OUT one CFG_TUD_ENDPOINT0_SIZE + // packet per submit; without this the DCP auto-accepts the next back-to-back packet into the + // just-emptied buffer and the following BRDY (remaining==0) BCLR-discards it, dropping 64 + // bytes mid-transfer (e.g. usbtest ctrl_out 512B). RA4M1 UM R01UH0887 DCPCTR.PID. + rusb->DCPCTR = RUSB2_PIPE_CTR_PID_NAK; return true; } @@ -244,7 +255,12 @@ static bool pipe_xfer_in(rusb2_reg_t* rusb, unsigned num) } const uint16_t mps = edpt_max_packet_size(rusb, num); - pipe_wait_for_ready(rusb, num); + if (!pipe_wait_for_ready(rusb, num)) { + // Buffer never came ready (double-buffered IN pipe full, host not draining). Drop this load; + // the transfer stays pending and is retried when a BRDY frees a plane or the pipe is re-armed. + rusb->D0FIFOSEL = 0; + return false; + } uint16_t len = tu_min16(rem, mps); void *buf = pipe->buf; @@ -285,7 +301,10 @@ static bool pipe_xfer_out(rusb2_reg_t* rusb, unsigned num) rusb->D0FIFOSEL = fifo_sel; const uint16_t mps = edpt_max_packet_size(rusb, num); - pipe_wait_for_ready(rusb, num); + if (!pipe_wait_for_ready(rusb, num)) { + rusb->D0FIFOSEL = 0; + return false; // FIFO not ready; leave the receive pending (BRDY re-enters when data arrives) + } const uint16_t vld = (uint16_t)rusb->D0FIFOCTR_b.DTLN; const uint16_t len = tu_min16(tu_min16(rem, mps), vld); @@ -351,7 +370,16 @@ static void process_status_completion(uint8_t rhport) dcd_event_xfer_complete(rhport, ep_addr, 0, XFER_RESULT_SUCCESS, true); } -static bool process_pipe0_xfer(rusb2_reg_t *rusb, int buffer_type, uint8_t ep_addr, void *buffer, +// Report a completed transfer on `num` and reset its bookkeeping. Single completion path for the +// BRDY handler and the EP0 parked-packet drain, so they can't diverge (e.g. on clearing `queued`). +static void pipe_xfer_complete(uint8_t rhport, unsigned num, bool in_isr) { + pipe_state_t *pipe = &_dcd.pipe[num]; + pipe->queued = false; + dcd_event_xfer_complete(rhport, pipe->ep, pipe->length - pipe->remaining, + XFER_RESULT_SUCCESS, in_isr); +} + +static bool process_pipe0_xfer(uint8_t rhport, rusb2_reg_t *rusb, int buffer_type, uint8_t ep_addr, void *buffer, uint16_t total_bytes) { uint16_t fifo_sel = (rusb2_is_highspeed_reg(rusb) ? RUSB2_FIFOSEL_MBW_32BIT : RUSB2_FIFOSEL_MBW_16BIT) | FIFOSEL_BIGEND; @@ -377,6 +405,15 @@ static bool process_pipe0_xfer(rusb2_reg_t *rusb, int buffer_type, uint8_t ep_ad /* IN */ TU_ASSERT(rusb->DCPCTR_b.BSTS && (rusb->USBREQ & 0x80)); pipe0_xfer_in(rusb); + } else if (rusb->CFIFOCTR_b.DTLN > 0) { + /* OUT: a back-to-back packet parked by pipe0_xfer_out already sits in the DCP buffer (its + BRDY has fired and been cleared) — deliver it into this chunk now; no new BRDY will come + for it. Runs with the USB IRQ masked (dcd_edpt_xfer). Detected via the hardware DTLN + rather than a driver flag: the BCLR at SETUP/bus-reset then self-heals any parked state. */ + if (pipe0_xfer_out(rusb)) { + pipe_xfer_complete(rhport, 0, false); + return true; // PID stays NAK (set by pipe0_xfer_out) until the next chunk is armed + } } rusb->DCPCTR = RUSB2_PIPE_CTR_PID_BUF; } else { @@ -388,6 +425,24 @@ static bool process_pipe0_xfer(rusb2_reg_t *rusb, int buffer_type, uint8_t ep_ad return true; } +// Queue a zero-length IN packet. Returns false if the FIFO buffer wasn't free (double-buffered pipe +// full, host not draining) so BVAL couldn't be written -- the caller retries on the next BRDY. +static bool pipe_zlp_in(rusb2_reg_t *rusb, unsigned num) { + rusb->D0FIFOSEL = (uint16_t) num; + const bool ready = pipe_wait_for_ready(rusb, num); + if (ready) { + rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + } + rusb->D0FIFOSEL = 0; + // deselect completes within a few bus cycles (not host-dependent), but bound it anyway: this + // runs with the USB IRQ masked, where any stuck spin freezes the whole stack + uint32_t spin = RUSB2_FIFO_READY_SPIN; + while (rusb->D0FIFOSEL_b.CURPIPE) { + if (!spin--) { break; } + } + return ready; +} + static bool process_pipe_xfer(rusb2_reg_t* rusb, int buffer_type, uint8_t ep_addr, void* buffer, uint16_t total_bytes) { const unsigned epn = tu_edpt_number(ep_addr); @@ -397,23 +452,20 @@ static bool process_pipe_xfer(rusb2_reg_t* rusb, int buffer_type, uint8_t ep_add TU_ASSERT(num); pipe_state_t *pipe = &_dcd.pipe[num]; - pipe->ff = buffer_type; - pipe->buf = buffer; - pipe->length = total_bytes; - pipe->remaining = total_bytes; + pipe->ff = buffer_type; + pipe->buf = buffer; + pipe->length = total_bytes; + pipe->remaining = total_bytes; + pipe->queued = true; + pipe->zlp_pending = false; if (dir) { /* IN */ if (total_bytes) { pipe_xfer_in(rusb, num); } else { - /* ZLP */ - rusb->D0FIFOSEL = num; - pipe_wait_for_ready(rusb, num); - rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; - rusb->D0FIFOSEL = 0; - /* if CURPIPE bits changes, check written value */ - while (rusb->D0FIFOSEL_b.CURPIPE) {} + /* ZLP: if the FIFO buffer isn't free yet, defer the queue to the next BRDY (see process_pipe_brdy) */ + pipe->zlp_pending = !pipe_zlp_in(rusb, num); } } else { // OUT @@ -436,11 +488,11 @@ static bool process_pipe_xfer(rusb2_reg_t* rusb, int buffer_type, uint8_t ep_add return true; } -static bool process_edpt_xfer(rusb2_reg_t* rusb, int buffer_type, uint8_t ep_addr, void* buffer, uint16_t total_bytes) +static bool process_edpt_xfer(uint8_t rhport, rusb2_reg_t* rusb, int buffer_type, uint8_t ep_addr, void* buffer, uint16_t total_bytes) { const unsigned epn = tu_edpt_number(ep_addr); if (0 == epn) { - return process_pipe0_xfer(rusb, buffer_type, ep_addr, buffer, total_bytes); + return process_pipe0_xfer(rhport, rusb, buffer_type, ep_addr, buffer, total_bytes); } else { return process_pipe_xfer(rusb, buffer_type, ep_addr, buffer, total_bytes); } @@ -466,7 +518,15 @@ static void process_pipe_brdy(uint8_t rhport, unsigned num) if (dir) { /* IN */ - completed = pipe_xfer_in(rusb, num); + if (pipe->zlp_pending) { + // The submit-time ZLP couldn't be queued (FIFO full); a freed buffer plane lets us queue it + // now. Don't report completion until the ZLP is actually queued (and then sent, next BRDY), + // otherwise a spurious BRDY would complete a zero-length IN the host never received. + pipe->zlp_pending = !pipe_zlp_in(rusb, num); + completed = false; + } else { + completed = pipe_xfer_in(rusb, num); + } } else { // OUT if (num) { @@ -476,9 +536,7 @@ static void process_pipe_brdy(uint8_t rhport, unsigned num) } } if (completed) { - dcd_event_xfer_complete(rhport, pipe->ep, - pipe->length - pipe->remaining, - XFER_RESULT_SUCCESS, true); + pipe_xfer_complete(rhport, num, true); // TU_LOG1("C %d %d\r\n", num, pipe->length - pipe->remaining); } } @@ -603,19 +661,8 @@ bool dcd_init(uint8_t rhport, const tusb_rhport_init_t* rh_init) { #ifdef RUSB2_SUPPORT_HIGHSPEED if ( rusb2_is_highspeed_rhport(rhport) ) { - rusb->SYSCFG_b.HSE = 1; - - // leave CLKSEL as default (0x11) 24Mhz - - // Power and reset UTMI Phy - uint16_t physet = (rusb->PHYSET | RUSB2_PHYSET_PLLRESET_Msk) & ~RUSB2_PHYSET_DIRPD_Msk; - rusb->PHYSET = physet; - R_BSP_SoftwareDelay((uint32_t) 1, BSP_DELAY_UNITS_MILLISECONDS); - rusb->PHYSET_b.PLLRESET = 0; - - // set UTMI to operating mode and wait for PLL lock confirmation - rusb->LPSTS_b.SUSPENDM = 1; - while (!rusb->PLLSTA_b.PLLLOCK) {} + rusb->SYSCFG_b.HSE = TUD_OPT_HIGH_SPEED ? 1 : 0; // FS-only build: no HS chirp + rusb2_utmi_phy_powerup(rusb); rusb->SYSCFG_b.DRPD = 0; rusb->SYSCFG_b.USBE = 1; @@ -720,10 +767,20 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) if ( !rusb2_is_highspeed_rhport(rhport) && mps > 256) { return false; } + } else if (xfer == TUSB_XFER_INTERRUPT) { + // Interrupt pipes (6-9) have a fixed 64-byte buffer even in high speed (RA6M5 UM 29.1); + // a larger PIPEMAXP would enumerate, then silently truncate every transfer + TU_ASSERT(mps <= 64); } - const unsigned num = find_pipe(xfer); - TU_ASSERT(num); + // Re-opening an endpoint must reuse its pipe: usbd_edpt_close() is a no-op on ISO_ALLOC ports, + // so a class's close/open across SET_INTERFACE (e.g. video's notification endpoint) would + // otherwise allocate a second pipe with the same EPNUM and leak pipes until exhaustion. + unsigned num = _dcd.ep[dir][epn]; + if (num == 0) { + num = find_pipe(xfer); + TU_ASSERT(num); + } _dcd.pipe[num].ep = ep_addr; _dcd.ep[dir][epn] = num; @@ -731,13 +788,12 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) /* setup pipe */ dcd_int_disable(rhport); + rusb->PIPESEL = num; if ( rusb2_is_highspeed_rhport(rhport) ) { - // FIXME shouldn't be after pipe selection and config, also the BUFNMB should be changed - // depending on the allocation scheme + // PIPEBUF is PIPESEL-windowed (RA6M5 UM 29.2.35): write it after selecting the pipe. + // FIXME BUFNMB is a fixed 0x08 for every pipe; a real per-pipe allocation scheme is needed. rusb->PIPEBUF = 0x7C08; } - - rusb->PIPESEL = num; rusb->PIPEMAXP = mps; volatile uint16_t *ctr = get_pipectr(rusb, num); *ctr = RUSB2_PIPE_CTR_ACLRM_Msk | RUSB2_PIPE_CTR_SQCLR_Msk; @@ -766,6 +822,8 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) return true; } +static void edpt_close(uint8_t rhport, uint8_t ep_addr); + void dcd_edpt_close_all(uint8_t rhport) { unsigned i = TU_ARRAY_SIZE(_dcd.pipe); @@ -775,12 +833,14 @@ void dcd_edpt_close_all(uint8_t rhport) if (!ep_addr) { continue; } - dcd_edpt_close(rhport, (uint8_t)ep_addr); + edpt_close(rhport, (uint8_t)ep_addr); } dcd_int_enable(rhport); } -void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) +// Internal helper: on this (ISO_ALLOC) IP the stack no longer calls dcd_edpt_close(); only +// dcd_edpt_close_all() uses it to tear down each pipe. +static void edpt_close(uint8_t rhport, uint8_t ep_addr) { rusb2_reg_t * rusb = RUSB2_REG(rhport); const unsigned epn = tu_edpt_number(ep_addr); @@ -792,24 +852,73 @@ void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) *ctr = 0; rusb->PIPESEL = (uint16_t)num; rusb->PIPECFG = 0; - _dcd.pipe[num].ep = 0; + _dcd.pipe[num].ep = 0; + _dcd.pipe[num].queued = false; + _dcd.pipe[num].zlp_pending = false; _dcd.ep[dir][epn] = 0; } -#if 0 bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { - (void)rhport; - (void)ep_addr; - (void)largest_packet_size; - return false; + rusb2_reg_t * rusb = RUSB2_REG(rhport); + const unsigned epn = tu_edpt_number(ep_addr); + const unsigned dir = tu_edpt_dir(ep_addr); + + // Fullspeed ISO is limited to 256 bytes + if (!rusb2_is_highspeed_rhport(rhport) && largest_packet_size > 256) { + return false; + } + + // Reserve an ISO-capable pipe (1 or 2) once; it persists across altsetting changes so + // dcd_edpt_iso_activate() only has to re-arm it in place (no pipe free/realloc, which on this + // shared-register IP would churn PIPESEL/PIPECFG and disturb the other pipes). + const unsigned num = find_pipe(TUSB_XFER_ISOCHRONOUS); + TU_ASSERT(num); + _dcd.pipe[num].ep = ep_addr; + _dcd.ep[dir][epn] = num; + + dcd_int_disable(rhport); + rusb->PIPESEL = (uint16_t) num; + if (rusb2_is_highspeed_rhport(rhport)) { + // PIPEBUF is PIPESEL-windowed (RA6M5 UM 29.2.35): write it after selecting the pipe. + // FIXME (as in dcd_edpt_open): BUFNMB is a fixed 0x08 for every pipe; a real allocator is needed. + rusb->PIPEBUF = 0x7C08; + } + rusb->PIPEMAXP = largest_packet_size; + volatile uint16_t *ctr = get_pipectr(rusb, num); + *ctr = RUSB2_PIPE_CTR_ACLRM_Msk | RUSB2_PIPE_CTR_SQCLR_Msk; + *ctr = 0; // leave the pipe NAKing until activated + rusb->PIPECFG = (uint16_t) ((dir << 4) | epn | RUSB2_PIPECFG_TYPE_ISO | RUSB2_PIPECFG_DBLB_Msk); + rusb->BRDYSTS = (uint16_t) (0x3FFu ^ TU_BIT(num)); + rusb->BRDYENB |= TU_BIT(num); + dcd_int_enable(rhport); + return true; } bool dcd_edpt_iso_activate(uint8_t rhport, const tusb_desc_endpoint_t *desc_ep) { - (void)rhport; - (void)desc_ep; - return false; + rusb2_reg_t * rusb = RUSB2_REG(rhport); + const uint8_t ep_addr = desc_ep->bEndpointAddress; + const unsigned epn = tu_edpt_number(ep_addr); + const unsigned dir = tu_edpt_dir(ep_addr); + const unsigned num = _dcd.ep[dir][epn]; + TU_ASSERT(num); // must have been iso-alloc'd + + dcd_int_disable(rhport); + rusb->PIPESEL = (uint16_t) num; + rusb->PIPEMAXP = tu_edpt_packet_size(desc_ep); + volatile uint16_t *ctr = get_pipectr(rusb, num); + *ctr = RUSB2_PIPE_CTR_ACLRM_Msk | RUSB2_PIPE_CTR_SQCLR_Msk; // abort in-flight + reset data toggle + *ctr = 0; + // a transfer armed before SET_INTERFACE survives to here (no dcd close on this port): drop the + // stale bookkeeping so a BRDY firing before the class re-arms can't replay it + pipe_state_t *pipe = &_dcd.pipe[num]; + pipe->buf = NULL; + pipe->remaining = 0; + pipe->queued = false; + pipe->zlp_pending = false; + *ctr = RUSB2_PIPE_CTR_PID_BUF; // enable + dcd_int_enable(rhport); + return true; } -#endif bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes, bool is_isr) { @@ -817,7 +926,7 @@ bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t t rusb2_reg_t* rusb = RUSB2_REG(rhport); dcd_int_disable(rhport); - bool r = process_edpt_xfer(rusb, 0, ep_addr, buffer, total_bytes); + bool r = process_edpt_xfer(rhport, rusb, 0, ep_addr, buffer, total_bytes); dcd_int_enable(rhport); return r; @@ -830,7 +939,7 @@ bool dcd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16_ rusb2_reg_t* rusb = RUSB2_REG(rhport); dcd_int_disable(rhport); - bool r = process_edpt_xfer(rusb, 1, ep_addr, ff, total_bytes); + bool r = process_edpt_xfer(rhport, rusb, 1, ep_addr, ff, total_bytes); dcd_int_enable(rhport); return r; @@ -865,7 +974,19 @@ void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) } else { const unsigned num = _dcd.ep[0][tu_edpt_number(ep_addr)]; rusb->PIPESEL = (uint16_t)num; - if (rusb->PIPECFG_b.TYPE != 1) { + // Drop any packet parked in the buffer while halted: a data-OUT packet the host sent before + // aborting its transfer would otherwise be delivered into the next read after recovery + // (BOT reset + clear-halt re-arms a 31-byte CBW read which then receives stale WRITE data, + // "SCSI CBW is not valid" -> stall -> reset loop; ra6m5 msc write wedge). + *ctr = RUSB2_PIPE_CTR_ACLRM_Msk; + *ctr = 0; + // Non-bulk OUT re-enables straight away. Bulk OUT is normally armed together with its transaction + // counter (TRE) by process_pipe_xfer(), so we don't blindly re-enable it here — but if a receive + // was already armed (still queued), SQCLR above just left it NAKing. Re-assert BUF so it keeps + // receiving; the class driver still considers that read submitted and never re-arms it, so + // otherwise the endpoint NAKs forever (usbtest toggle test 29 clears the halt on an armed pipe). + // `queued` (not `buf`) is the armed test: a zero-length OUT read has buf==NULL yet is armed. + if (rusb->PIPECFG_b.TYPE != 1 || _dcd.pipe[num].queued) { *ctr = RUSB2_PIPE_CTR_PID_BUF; } } diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 4c3315044..489162e54 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -1,26 +1,8 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021 Koji Kitayama - * Portions copyrighted (c) 2021 Roland Winistoerfer - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021 Koji Kitayama + * SPDX-FileCopyrightText: Portions copyrighted (c) 2021 Roland Winistoerfer + * SPDX-FileCopyrightText: Copyright (c) 2021 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -472,11 +454,9 @@ bool hcd_init(uint8_t rhport, const tusb_rhport_init_t* rh_init) { if (rusb2_is_highspeed_rhport(rhport) ) { rusb->SYSCFG_b.HSE = 1; rusb->PHYSET_b.HSEB = 0; - rusb->PHYSET_b.DIRPD = 0; - R_BSP_SoftwareDelay((uint32_t) 1, BSP_DELAY_UNITS_MILLISECONDS); - rusb->PHYSET_b.PLLRESET = 0; - rusb->LPSTS_b.SUSPENDM = 1; - while ( !rusb->PLLSTA_b.PLLLOCK ); + // same PHY reference-clock + power-up requirements as dcd_init: without CLKSEL matching the + // board XTAL the PLL never locks and the wait below would spin forever (e.g. EK-RA8M1, 20 MHz) + rusb2_utmi_phy_powerup(rusb); rusb->SYSCFG_b.DRPD = 1; rusb->SYSCFG_b.DCFM = 1; rusb->SYSCFG_b.DPRPU = 0; diff --git a/src/portable/renesas/rusb2/rusb2_common.c b/src/portable/renesas/rusb2/rusb2_common.c index 8addbe4c6..c13b47c2b 100644 --- a/src/portable/renesas/rusb2/rusb2_common.c +++ b/src/portable/renesas/rusb2/rusb2_common.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2023 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2023 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/renesas/rusb2/rusb2_common.h b/src/portable/renesas/rusb2/rusb2_common.h index 6b8c3d7f2..90abdf4b9 100644 --- a/src/portable/renesas/rusb2/rusb2_common.h +++ b/src/portable/renesas/rusb2/rusb2_common.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2025 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2025 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 4774d2e2c..0954d0d25 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2022 Rafael Silva (@perigoso) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2022 Rafael Silva (@perigoso) + * SPDX-FileCopyrightText: Copyright (c) 2022 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -67,6 +49,23 @@ typedef struct { #define rusb2_is_highspeed_rhport(_p) (_p == 1) #define rusb2_is_highspeed_reg(_reg) (_reg == RUSB2_REG(1)) + + // UTMI PHY reference clock is the main oscillator: PHYSET.CLKSEL must match the board XTAL + // before the PHY PLL is released (RA6M5 UM R01UH0891 29.2.17: 00=12 MHz, 10=20 MHz, + // 11=24 MHz reset default). EK-RA6M5 runs 24 MHz (default works); EK-RA8M1 runs 20 MHz and + // never locks/chirps on the default. A board with a non-standard USB clocking scheme can + // pre-define RUSB2_PHYSET_CLKSEL_VALUE to override this selection. + #ifndef RUSB2_PHYSET_CLKSEL_VALUE + #if BSP_CFG_XTAL_HZ == 12000000 + #define RUSB2_PHYSET_CLKSEL_VALUE 0u + #elif BSP_CFG_XTAL_HZ == 20000000 + #define RUSB2_PHYSET_CLKSEL_VALUE 2u + #elif BSP_CFG_XTAL_HZ == 24000000 + #define RUSB2_PHYSET_CLKSEL_VALUE 3u + #else + #error "USBHS UTMI PHY: no PHYSET.CLKSEL encoding for this BSP_CFG_XTAL_HZ; define RUSB2_PHYSET_CLKSEL_VALUE" + #endif + #endif #else #define RUSB2_CONTROLLER_COUNT 1 @@ -102,6 +101,31 @@ TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_disable(uint8_t rhport) { TU_ATTR_ALWAYS_INLINE static inline void rusb2_phy_init(void) { } +#ifdef RUSB2_SUPPORT_HIGHSPEED +// UTMI PHY power-up per the FSP reference sequence (r_usb_preg_access.c), shared by dcd_init and +// hcd_init: program CLKSEL to the board XTAL while the PHY is powered down (DIRPD=1), 1 us, +// release DIRPD, 1 ms, release PLLRESET, then wait for PLL lock. Changing CLKSEL as the PHY +// powers up gets mis-sampled (EK-RA8M1, 20 MHz). +static inline void rusb2_utmi_phy_powerup(rusb2_reg_t* rusb) { + uint16_t physet = rusb->PHYSET | RUSB2_PHYSET_DIRPD_Msk; + rusb->PHYSET = physet; + #ifdef RUSB2_PHYSET_CLKSEL_VALUE + physet = (uint16_t) ((physet & ~RUSB2_PHYSET_CLKSEL_Msk) | + (RUSB2_PHYSET_CLKSEL_VALUE << RUSB2_PHYSET_CLKSEL_Pos)); + rusb->PHYSET = physet; + #endif + R_BSP_SoftwareDelay((uint32_t) 1, BSP_DELAY_UNITS_MICROSECONDS); + physet &= (uint16_t) ~RUSB2_PHYSET_DIRPD_Msk; + rusb->PHYSET = physet; + R_BSP_SoftwareDelay((uint32_t) 1, BSP_DELAY_UNITS_MILLISECONDS); + rusb->PHYSET_b.PLLRESET = 0; + + // set UTMI to operating mode and wait for PLL lock confirmation + rusb->LPSTS_b.SUSPENDM = 1; + while (!rusb->PLLSTA_b.PLLLOCK) {} +} +#endif + #ifdef __cplusplus } #endif diff --git a/src/portable/renesas/rusb2/rusb2_rx.h b/src/portable/renesas/rusb2/rusb2_rx.h index 7bf4be47e..fba51f550 100644 --- a/src/portable/renesas/rusb2/rusb2_rx.h +++ b/src/portable/renesas/rusb2/rusb2_rx.h @@ -1,27 +1,9 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2020 Koji Kitayama - * Portions copyrighted (c) 2021 Roland Winistoerfer - * Copyright (c) 2022 Rafael Silva (@perigoso) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2020 Koji Kitayama + * SPDX-FileCopyrightText: Portions copyrighted (c) 2021 Roland Winistoerfer + * SPDX-FileCopyrightText: Copyright (c) 2022 Rafael Silva (@perigoso) + * SPDX-FileCopyrightText: Copyright (c) 2020 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/renesas/rusb2/rusb2_type.h b/src/portable/renesas/rusb2/rusb2_type.h index 21f116857..511a898b6 100644 --- a/src/portable/renesas/rusb2/rusb2_type.h +++ b/src/portable/renesas/rusb2/rusb2_type.h @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2022 Rafael Silva (@perigoso) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2022 Rafael Silva (@perigoso) + * SPDX-FileCopyrightText: Copyright (c) 2022 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/sony/cxd56/dcd_cxd56.c b/src/portable/sony/cxd56/dcd_cxd56.c index be694edfa..f70ae826d 100644 --- a/src/portable/sony/cxd56/dcd_cxd56.c +++ b/src/portable/sony/cxd56/dcd_cxd56.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright 2019 Sony Semiconductor Solutions Corporation - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright 2019 Sony Semiconductor Solutions Corporation + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index f5a8beb65..ba05818b6 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -1,30 +1,9 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Nathan Conrad - * - * Portions: - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * Copyright (c) 2022 Simon Küppers (skuep) - * Copyright (c) 2022 HiFiPhile - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Nathan Conrad + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-FileCopyrightText: Copyright (c) 2022 Simon Küppers (skuep) + * SPDX-FileCopyrightText: Copyright (c) 2022 HiFiPhile (Zixun LI) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -856,7 +835,17 @@ void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { ep_reg &= U_EPREG_MASK | EP_STAT_MASK(dir) | EP_DTOG_MASK(dir); if (!ep_is_iso(ep_reg)) { - ep_change_status(&ep_reg, dir, EP_STAT_NAK); + // Only knock a genuinely STALLED endpoint down to NAK (the class then re-arms it). If the + // endpoint is armed (VALID) - e.g. a clear-halt used purely to reset the data toggle, as in + // usbtest case 29 - leave STAT untouched so the in-flight transfer isn't disarmed with no + // completion, which would leak the usbd claim and starve the endpoint. Masking the STAT bits + // to 0 writes no toggle, so an armed/idle endpoint keeps its current status. + const uint8_t stat_pos = (uint8_t) (U_EPTX_STAT_Pos + (dir == TUSB_DIR_IN ? 0u : 8u)); + if (((ep_reg >> stat_pos) & 0x3u) == EP_STAT_STALL) { + ep_change_status(&ep_reg, dir, EP_STAT_NAK); + } else { + ep_reg &= ~EP_STAT_MASK(dir); + } } ep_change_dtog(&ep_reg, dir, 0); // Reset to DATA0 ep_write(ep_idx, ep_reg, true); diff --git a/src/portable/st/stm32_fsdev/fsdev_apm32.h b/src/portable/st/stm32_fsdev/fsdev_apm32.h new file mode 100644 index 000000000..5031445e8 --- /dev/null +++ b/src/portable/st/stm32_fsdev/fsdev_apm32.h @@ -0,0 +1,77 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2024, hathach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + */ +#ifndef TUSB_FSDEV_APM32_H +#define TUSB_FSDEV_APM32_H + +#include "common/tusb_compiler.h" + +#if CFG_TUSB_MCU == OPT_MCU_APM32F0XX + #include "apm32f0xx.h" +#endif + +#define FSDEV_USE_SBUF_ISO 0 +#define FSDEV_REG_BASE ((uint32_t)(USBD_BASE)) +#define FSDEV_PMA_BASE ((uint32_t)(USBD_BASE + 0x400UL)) + +#ifndef CFG_TUD_FSDEV_DOUBLE_BUFFERED_ISO_EP + #define CFG_TUD_FSDEV_DOUBLE_BUFFERED_ISO_EP 0 +#endif + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +static const IRQn_Type fsdev_irq[] = { + USBD_IRQn +}; +enum { FSDEV_IRQ_NUM = TU_ARRAY_SIZE(fsdev_irq) }; + +TU_ATTR_ALWAYS_INLINE static inline void fsdev_int_enable(uint8_t rhport) { + (void)rhport; + for (uint8_t i = 0; i < FSDEV_IRQ_NUM; i++) { + NVIC_EnableIRQ(fsdev_irq[i]); + } +} + +TU_ATTR_ALWAYS_INLINE static inline void fsdev_int_disable(uint8_t rhport) { + (void)rhport; + for (uint8_t i = 0; i < FSDEV_IRQ_NUM; i++) { + NVIC_DisableIRQ(fsdev_irq[i]); + } +} + +TU_ATTR_ALWAYS_INLINE static inline void fsdev_disconnect(uint8_t rhport) { + (void) rhport; + FSDEV_REG->CNTR |= U_CNTR_PDWN; + FSDEV_REG->BCDR &= ~U_BCDR_DPPU; +} + +TU_ATTR_ALWAYS_INLINE static inline void fsdev_connect(uint8_t rhport) { + (void) rhport; + FSDEV_REG->CNTR &= ~U_CNTR_PDWN; + FSDEV_REG->BCDR |= U_BCDR_DPPU; +} + +#endif diff --git a/src/portable/st/stm32_fsdev/fsdev_at32.h b/src/portable/st/stm32_fsdev/fsdev_at32.h index 107884370..9138dc101 100644 --- a/src/portable/st/stm32_fsdev/fsdev_at32.h +++ b/src/portable/st/stm32_fsdev/fsdev_at32.h @@ -1,26 +1,6 @@ /* -* The MIT License (MIT) - * - * Copyright (c) 2024, hathach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * + * SPDX-FileCopyrightText: Copyright (c) 2024, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT */ #ifndef TUSB_FSDEV_AT32_H #define TUSB_FSDEV_AT32_H @@ -37,7 +17,7 @@ #define FSDEV_USE_SBUF_ISO 0 #define FSDEV_REG_BASE (APB1PERIPH_BASE + 0x00005C00UL) -#define FSDEV_PMA_BASE (APB1PERIPH_BASE + 0x00006000UL) +#define FSDEV_PMA_BASE (APB1PERIPH_BASE + 0x00007800UL) #ifndef CFG_TUD_FSDEV_DOUBLE_BUFFERED_ISO_EP #define CFG_TUD_FSDEV_DOUBLE_BUFFERED_ISO_EP 0 diff --git a/src/portable/st/stm32_fsdev/fsdev_ch32.h b/src/portable/st/stm32_fsdev/fsdev_ch32.h index b92bf3f58..2c13554d4 100644 --- a/src/portable/st/stm32_fsdev/fsdev_ch32.h +++ b/src/portable/st/stm32_fsdev/fsdev_ch32.h @@ -1,26 +1,6 @@ /* -* The MIT License (MIT) - * - * Copyright (c) 2024, hathach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * + * SPDX-FileCopyrightText: Copyright (c) 2024, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT */ /** <h2><center>© Copyright (c) 2016 STMicroelectronics. * All rights reserved.</center></h2> diff --git a/src/portable/st/stm32_fsdev/fsdev_common.c b/src/portable/st/stm32_fsdev/fsdev_common.c index 7c4572a1e..9c9233d12 100644 --- a/src/portable/st/stm32_fsdev/fsdev_common.c +++ b/src/portable/st/stm32_fsdev/fsdev_common.c @@ -1,26 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024 Ha Thach (tinyusb.org) - * Copyright (c) 2025, HiFiPhile (Zixun LI) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach (tinyusb.org) + * SPDX-FileCopyrightText: Copyright (c) 2025, HiFiPhile (Zixun LI) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -52,6 +33,11 @@ void fsdev_core_reset(void) { // Clear pending interrupts FSDEV_REG->ISTR = 0; + + #if (CFG_TUSB_MCU == OPT_MCU_AT32F403A_407) || (CFG_TUSB_MCU == OPT_MCU_AT32F413) + // Enable larger PMA area + CRM->misc1_bit.usbbufs = 1; + #endif } // De-initialize the USB Core diff --git a/src/portable/st/stm32_fsdev/fsdev_common.h b/src/portable/st/stm32_fsdev/fsdev_common.h index af84b8b97..00d9b513a 100644 --- a/src/portable/st/stm32_fsdev/fsdev_common.h +++ b/src/portable/st/stm32_fsdev/fsdev_common.h @@ -1,27 +1,8 @@ /* - * The MIT License (MIT) - * - * Copyright (c) N Conrad - * Copyright (c) 2024, hathach (tinyusb.org) - * Copyright (c) 2025, HiFiPhile (Zixun LI) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Nathan Conrad + * SPDX-FileCopyrightText: Copyright (c) 2024, Ha Thach (tinyusb.org) + * SPDX-FileCopyrightText: Copyright (c) 2025, HiFiPhile (Zixun LI) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -303,6 +284,8 @@ typedef struct { #include "fsdev_ch32.h" #elif defined(TUP_USBIP_FSDEV_AT32) #include "fsdev_at32.h" +#elif defined(TUP_USBIP_FSDEV_APM32) + #include "fsdev_apm32.h" #else #error "Unknown USB IP" #endif diff --git a/src/portable/st/stm32_fsdev/fsdev_stm32.h b/src/portable/st/stm32_fsdev/fsdev_stm32.h index 93cdac808..23e24752b 100644 --- a/src/portable/st/stm32_fsdev/fsdev_stm32.h +++ b/src/portable/st/stm32_fsdev/fsdev_stm32.h @@ -1,30 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright(c) N Conrad - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Nathan Conrad + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/st/stm32_fsdev/hcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/hcd_stm32_fsdev.c index f9201651a..1e84ed283 100644 --- a/src/portable/st/stm32_fsdev/hcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/hcd_stm32_fsdev.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2025 HiFiPhile (Zixun LI) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2025 HiFiPhile (Zixun LI) + * SPDX-FileCopyrightText: Copyright (c) 2025 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c index b4288968f..8ac9f148c 100644 --- a/src/portable/st/typec/typec_stm32.c +++ b/src/portable/st/typec/typec_stm32.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2023 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2023 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT */ #include "tusb_option.h" diff --git a/src/portable/sunxi/dcd_sunxi_musb.c b/src/portable/sunxi/dcd_sunxi_musb.c index 9fac0bc1c..c74ee68a0 100644 --- a/src/portable/sunxi/dcd_sunxi_musb.c +++ b/src/portable/sunxi/dcd_sunxi_musb.c @@ -1,27 +1,8 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021 Koji KITAYAMA - * Copyright (c) 2021 Tian Yunhao (t123yh) - * Copyright (c) 2021 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021 Koji Kitayama + * SPDX-FileCopyrightText: Copyright (c) 2021 Tian Yunhao (t123yh) + * SPDX-FileCopyrightText: Copyright (c) 2021 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/sunxi/musb_def.h b/src/portable/sunxi/musb_def.h index ce9b89d55..638f3c93d 100644 --- a/src/portable/sunxi/musb_def.h +++ b/src/portable/sunxi/musb_def.h @@ -1,27 +1,8 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021 Koji KITAYAMA - * Copyright (c) 2021 Tian Yunhao (t123yh) - * Copyright (c) 2021 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021 Koji Kitayama + * SPDX-FileCopyrightText: Copyright (c) 2021 Tian Yunhao (t123yh) + * SPDX-FileCopyrightText: Copyright (c) 2021 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index e1a2f6cf2..b2f1a93a4 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -1,28 +1,9 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 William D. Jones - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * Copyright (c) 2020 Jan Duempelmann - * Copyright (c) 2020 Reinhard Panhuber - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 William D. Jones + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-FileCopyrightText: Copyright (c) 2020 Jan Duempelmann + * SPDX-FileCopyrightText: Copyright (c) 2020 Reinhard Panhuber + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -412,10 +393,6 @@ static void edpt_schedule_packets(uint8_t rhport, const uint8_t epnum, const uin } dep->diepdma = (uintptr_t) xfer->buffer; dep->diepctl = depctl.value; // enable endpoint - // Advance buffer pointer for EP0 - if (epnum == 0) { - xfer->buffer += total_bytes; - } } else #endif { @@ -751,6 +728,8 @@ static void handle_bus_reset(uint8_t rhport) { tu_memclr(xfer_status, sizeof(xfer_status)); + _dcd_data.ep0_pending[TUSB_DIR_OUT] = 0; + _dcd_data.ep0_pending[TUSB_DIR_IN] = 0; _dcd_data.sof_en = false; _dcd_data.allocated_epin_count = 0; @@ -1028,6 +1007,10 @@ static void handle_epout_dma(uint8_t rhport, uint8_t epnum, dwc2_doepint_t doepi if (edpt_is_enabled(epin0)) { edpt_disable(rhport, 0x80, false); } + // a new SETUP aborts any in-progress control transfer: drop leftover EP0 chunking state so a + // stale latched completion cannot re-arm from it + _dcd_data.ep0_pending[TUSB_DIR_OUT] = 0; + _dcd_data.ep0_pending[TUSB_DIR_IN] = 0; dcd_dcache_invalidate(_dcd_usbbuf.setup_buffer, sizeof(_dcd_usbbuf.setup_buffer)); @@ -1048,24 +1031,37 @@ static void handle_epout_dma(uint8_t rhport, uint8_t epnum, dwc2_doepint_t doepi // only handle data skip if it is setup or status related // Normal OUT transfer complete if (!doepint_bm.status_phase_rx && !doepint_bm.setup_packet_rx) { + xfer_ctl_t* xfer = XFER_CTL_BASE(epnum, TUSB_DIR_OUT); if ((epnum == 0) && _dcd_data.ep0_pending[TUSB_DIR_OUT]) { - // EP0 can only handle one packet Schedule another packet to be received. + // EP0 can only handle one packet: invalidate and advance past the received bytes, then + // schedule the next. + if (xfer->buffer != NULL) { + dcd_dcache_invalidate(xfer->buffer, CFG_TUD_ENDPOINT0_SIZE); + xfer->buffer += CFG_TUD_ENDPOINT0_SIZE; + } edpt_schedule_packets(rhport, epnum, TUSB_DIR_OUT); } else { dwc2_dep_t* epout = &dwc2->epout[epnum]; - xfer_ctl_t* xfer = XFER_CTL_BASE(epnum, TUSB_DIR_OUT); // determine actual received bytes const dwc2_ep_tsize_t tsiz = {.value = epout->tsiz}; const uint16_t remain = tsiz.xfer_size; xfer->total_len -= remain; + // EP0 invalidates only this (final) chunk's DMA-written bytes: DOEPDMA "is incremented on + // every AHB transaction" (databook 7.1.83), i.e. it points past the last word written. + // Read it before dma_setup_prepare() re-targets it at the setup buffer + uint16_t inval_len = xfer->total_len; + if (epnum == 0) { + inval_len = (uint16_t)(epout->doepdma - (uintptr_t)xfer->buffer); + } + // prepare EP0 for next setup if(epnum == 0) { dma_setup_prepare(rhport); } - dcd_dcache_invalidate(xfer->buffer, xfer->total_len); + dcd_dcache_invalidate(xfer->buffer, inval_len); dcd_event_xfer_complete(rhport, epnum, xfer->total_len, XFER_RESULT_SUCCESS, true); } } @@ -1077,7 +1073,10 @@ static void handle_epin_dma(uint8_t rhport, uint8_t epnum, dwc2_diepint_t diepin if (diepint_bm.xfer_complete) { if ((epnum == 0) && _dcd_data.ep0_pending[TUSB_DIR_IN]) { - // EP0 can only handle one packet. Schedule another packet to be transmitted. + // EP0 can only handle one packet: advance past the sent bytes, then schedule the next. + if (xfer->buffer != NULL) { + xfer->buffer += CFG_TUD_ENDPOINT0_SIZE; + } edpt_schedule_packets(rhport, epnum, TUSB_DIR_IN); } else { dcd_event_xfer_complete(rhport, epnum | TUSB_DIR_IN_MASK, xfer->total_len, XFER_RESULT_SUCCESS, true); @@ -1144,7 +1143,12 @@ static void handle_incomplete_iso_in(uint8_t rhport) { xfer_ctl_t *xfer = XFER_CTL_BASE(epnum, TUSB_DIR_IN); if (xfer->iso_retry > 0) { xfer->iso_retry--; - // Restart ISO transfe: re-write TSIZ and CTL + // Restart ISO transfer: re-write DMA address, TSIZ, and CTL + #if CFG_TUD_DWC2_DMA_ENABLE + if (dma_device_enabled(dwc2)) { + epin->diepdma = (uintptr_t) xfer->buffer; + } + #endif dwc2_ep_tsize_t deptsiz = {.value = 0}; deptsiz.xfer_size = xfer->total_len; deptsiz.packet_count = tu_div_ceil(xfer->total_len, xfer->max_size); diff --git a/src/portable/synopsys/dwc2/dwc2_at32.h b/src/portable/synopsys/dwc2/dwc2_at32.h index 85fa9b20b..828af3055 100644 --- a/src/portable/synopsys/dwc2/dwc2_at32.h +++ b/src/portable/synopsys/dwc2/dwc2_at32.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/synopsys/dwc2/dwc2_bcm.h b/src/portable/synopsys/dwc2/dwc2_bcm.h index 91cae821e..8119d9139 100644 --- a/src/portable/synopsys/dwc2/dwc2_bcm.h +++ b/src/portable/synopsys/dwc2/dwc2_bcm.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/synopsys/dwc2/dwc2_common.c b/src/portable/synopsys/dwc2/dwc2_common.c index 33eabaeab..0e38218e3 100644 --- a/src/portable/synopsys/dwc2/dwc2_common.c +++ b/src/portable/synopsys/dwc2/dwc2_common.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024-2025 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/synopsys/dwc2/dwc2_common.h b/src/portable/synopsys/dwc2/dwc2_common.h index 5c4798d21..22a04c464 100644 --- a/src/portable/synopsys/dwc2/dwc2_common.h +++ b/src/portable/synopsys/dwc2/dwc2_common.h @@ -1,25 +1,6 @@ /* -* The MIT License (MIT) - * - * Copyright (c) 2024 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/synopsys/dwc2/dwc2_efm32.h b/src/portable/synopsys/dwc2/dwc2_efm32.h index 063360873..8b2922cc9 100644 --- a/src/portable/synopsys/dwc2/dwc2_efm32.h +++ b/src/portable/synopsys/dwc2/dwc2_efm32.h @@ -1,26 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021 Rafael Silva (@perigoso) - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021 Rafael Silva (@perigoso) + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/synopsys/dwc2/dwc2_esp32.h b/src/portable/synopsys/dwc2/dwc2_esp32.h index 436f8dc30..c7a7d7d25 100644 --- a/src/portable/synopsys/dwc2/dwc2_esp32.h +++ b/src/portable/synopsys/dwc2/dwc2_esp32.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/synopsys/dwc2/dwc2_gd32.h b/src/portable/synopsys/dwc2/dwc2_gd32.h index 28c3fde5e..2520972fe 100644 --- a/src/portable/synopsys/dwc2/dwc2_gd32.h +++ b/src/portable/synopsys/dwc2/dwc2_gd32.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/synopsys/dwc2/dwc2_nrf.h b/src/portable/synopsys/dwc2/dwc2_nrf.h index a1bf692f8..c5f50043d 100644 --- a/src/portable/synopsys/dwc2/dwc2_nrf.h +++ b/src/portable/synopsys/dwc2/dwc2_nrf.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2025 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2025 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. * diff --git a/src/portable/synopsys/dwc2/dwc2_stm32.h b/src/portable/synopsys/dwc2/dwc2_stm32.h index 126632fec..0c9b534d4 100644 --- a/src/portable/synopsys/dwc2/dwc2_stm32.h +++ b/src/portable/synopsys/dwc2/dwc2_stm32.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/synopsys/dwc2/dwc2_type.h b/src/portable/synopsys/dwc2/dwc2_type.h index 7c03a4a91..18e8dd02f 100644 --- a/src/portable/synopsys/dwc2/dwc2_type.h +++ b/src/portable/synopsys/dwc2/dwc2_type.h @@ -1,26 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024, hathach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * + * SPDX-FileCopyrightText: Copyright (c) 2024, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT */ /** <h2><center>© Copyright (c) 2019 STMicroelectronics. * All rights reserved.</center></h2> diff --git a/src/portable/synopsys/dwc2/dwc2_xmc.h b/src/portable/synopsys/dwc2/dwc2_xmc.h index 85b2a2633..16f051103 100644 --- a/src/portable/synopsys/dwc2/dwc2_xmc.h +++ b/src/portable/synopsys/dwc2/dwc2_xmc.h @@ -1,26 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2021 Rafael Silva (@perigoso) - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2021 Rafael Silva (@perigoso) + * SPDX-FileCopyrightText: Copyright (c) 2021, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/synopsys/dwc2/hcd_dwc2.c b/src/portable/synopsys/dwc2/hcd_dwc2.c index a536b1e36..5a171f80e 100644 --- a/src/portable/synopsys/dwc2/hcd_dwc2.c +++ b/src/portable/synopsys/dwc2/hcd_dwc2.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -45,6 +26,12 @@ #endif #define DWC2_CHANNEL_COUNT_MAX 16u // absolute max channel count + + // Conservative time budget for enabling a slave-mode periodic OUT channel and writing its first packet before the + // current (micro)frame ends. HFNUM.FrRem is measured in PHY clocks; 1024 clocks are 17.1 us at 60 MHz, 21.3 us at + // 48 MHz, or 34.1 us at 30 MHz. Defer to SOF when less time remains. + #define DWC2_PERIODIC_OUT_MIN_FRREM 1024u + TU_VERIFY_STATIC(CFG_TUH_DWC2_ENDPOINT_MAX <= 255, "currently only use 8-bit for index"); enum { @@ -56,7 +43,9 @@ enum { }; enum { - HCD_XFER_PERIOD_SPLIT_NYET_MAX = 3 + HCD_XFER_PERIOD_SPLIT_NYET_MAX = 3, + HCD_FRAME_NUMBER_MASK = 0x3fff, + HCD_FRAME_COUNT = HCD_FRAME_NUMBER_MASK + 1 }; //-------------------------------------------------------------------- @@ -75,18 +64,22 @@ typedef struct { }; struct TU_ATTR_PACKED { - uint32_t uframe_interval : 18; // micro-frame interval + uint32_t uframe_interval : 19; // micro-frame interval uint32_t speed : 2; uint32_t next_pid : 2; // PID for next transfer uint32_t next_do_ping : 1; // Do PING for next transfer if possible (highspeed OUT) uint32_t closing : 1; // endpoint is closing - // uint32_t : 8; + uint32_t aborting : 1; // periodic DMA channel is waiting for its automatic halt + uint32_t periodic_phase : 1; // periodic transfer phase is established + uint32_t xfer_pending : 1; // periodic transfer waiting for its service interval + // uint32_t : 4; }; - uint32_t uframe_countdown; // micro-frame count down to transfer for periodic, only need 18-bit + uint32_t uframe_countdown; // micro-frame count down to transfer for periodic, only need 19-bit uint8_t* buffer; uint16_t buflen; + uint16_t periodic_frame; // frame/microframe number of the last scheduled periodic transaction } hcd_endpoint_t; // Additional info for each channel when it is active @@ -105,6 +98,7 @@ typedef struct { // be composed of multiple channel_xfer_start() (retry with NAK/NYET) uint16_t fifo_bytes; // bytes written/read from/to FIFO (may not be transferred on USB bus). uint8_t retry_disabled; // 1: channel was disabled to throttle a split retry (NAK in / XactErr out); re-arm on its halt + volatile bool aborting; // periodic DMA abort waiting for the channel's automatic halt } hcd_xfer_t; typedef struct { @@ -206,7 +200,7 @@ TU_ATTR_ALWAYS_INLINE static inline bool channel_disable(const dwc2_regs_t* dwc2 // the worst case), the controller generates a channel halted and disables the channel automatically. // - For split enabled channels (both non-periodic and periodic), channel disable must not be programmed randomly. // However, channel disable can be programmed for specific scenarios such as NAK and FrmOvrn. - if (is_period && (channel->hcsplt & HCSPLT_SPLITEN)) { + if (is_period) { return true; } } else { @@ -219,13 +213,86 @@ TU_ATTR_ALWAYS_INLINE static inline bool channel_disable(const dwc2_regs_t* dwc2 return true; } -// attempt to send IN token to receive data -TU_ATTR_ALWAYS_INLINE static inline bool channel_send_in_token(const dwc2_regs_t* dwc2, dwc2_channel_t* channel) { +// Retire all active host channels on root-port disconnect without waiting for +// Channel Halted interrupts. +// stop new channel/FIFO interrupts, flush queued slave requests, request a +// halt for enabled channels, then clear their interrupt and software state. +static void channel_cleanup_on_disconnect(dwc2_regs_t *dwc2) { + const uint32_t xfer_ints = GINTSTS_NPTX_FIFO_EMPTY | GINTSTS_PTX_FIFO_EMPTY | GINTSTS_HCINT; + dwc2->gintmsk &= ~xfer_ints; + dwc2->gintsts = xfer_ints; + dwc2->haintmsk = 0; + + const uint8_t max_channel = dwc2_channel_count(dwc2); + #if CFG_TUH_DWC2_SLAVE_ENABLE + if (!dma_host_enabled(dwc2)) { + // With CHENA clear, CHDIS flushes a posted request without consuming + // request-queue space. Clear EPDIR as required for this flush operation. + for (uint8_t ch_id = 0; ch_id < max_channel; ch_id++) { + if (_hcd_data.xfer[ch_id].allocated) { + dwc2_channel_t *channel = &dwc2->channel[ch_id]; + const uint32_t hcchar = channel->hcchar; + if (hcchar & HCCHAR_CHENA) { + channel->hcchar = (hcchar & ~(HCCHAR_CHENA | HCCHAR_EPDIR)) | HCCHAR_CHDIS; + } + } + } + } + #endif + + for (uint8_t ch_id = 0; ch_id < max_channel; ch_id++) { + if (_hcd_data.xfer[ch_id].allocated) { + dwc2_channel_t *channel = &dwc2->channel[ch_id]; + const uint32_t hcchar = channel->hcchar; + if (hcchar & HCCHAR_CHENA) { + channel->hcchar = hcchar | HCCHAR_CHDIS; + } + channel->hcintmsk = 0; + channel->hcint = 0xFFFFFFFFU; + } + } + + tu_memclr(_hcd_data.xfer, sizeof(_hcd_data.xfer)); + for (uint8_t ep_id = 0; ep_id < CFG_TUH_DWC2_ENDPOINT_MAX; ep_id++) { + hcd_endpoint_t *edpt = &_hcd_data.edpt[ep_id]; + if (edpt->hcchar_bm.enable) { + edpt->closing = 1; + edpt->xfer_pending = 0; + } + } +} + +// Enable a channel, selecting the following frame for a new periodic transfer. +// Return that frame from the same HFNUM sample used for ODDFRM selection. +// Clear CHDIS explicitly: a halted channel may retain it in HCCHAR. +TU_ATTR_ALWAYS_INLINE static inline uint16_t channel_enable(dwc2_regs_t* dwc2, dwc2_channel_t* channel, + bool next_periodic_frame) { + uint32_t hcchar = channel->hcchar & ~HCCHAR_CHDIS; + uint16_t periodic_frame = 0; + if (next_periodic_frame) { + // Prevent the USB interrupt from consuming the selected frame before + // HCCHAR.CHENA is written. Queue-space waits happen before this helper. + const uint32_t gahbcfg = dwc2->gahbcfg; + dwc2->gahbcfg = gahbcfg & ~GAHBCFG_GINT; + const uint32_t hfnum = dwc2->hfnum; + hcchar = (hcchar & ~HCCHAR_ODDFRM) | (((hfnum & 1u) ^ 1u) << HCCHAR_ODDFRM_Pos); + channel->hcchar = hcchar | HCCHAR_CHENA; + periodic_frame = (uint16_t) ((hfnum + 1u) & HCD_FRAME_NUMBER_MASK); + dwc2->gahbcfg = gahbcfg; + } else { + channel->hcchar = hcchar | HCCHAR_CHENA; + } + return periodic_frame; +} + +// Attempt to send an IN token to receive data. For a new periodic transfer, +// select its frame only after request-queue space is available. +TU_ATTR_ALWAYS_INLINE static inline uint16_t channel_send_in_token(dwc2_regs_t* dwc2, dwc2_channel_t* channel, + bool next_periodic_frame) { while (0 == req_queue_avail(dwc2, channel_is_periodic(channel->hcchar))) { // blocking wait for request queue available } - channel->hcchar |= HCCHAR_CHENA; - return true; + return channel_enable(dwc2, channel, next_periodic_frame); } // Find currently enabled channel. Note: EP0 is bidirectional @@ -281,11 +348,13 @@ static void edpt_close(dwc2_regs_t *dwc2, uint8_t ep_id) { // Find an endpoint that is opened previously with hcd_edpt_open() // Note: EP0 is bidirectional -TU_ATTR_ALWAYS_INLINE static inline uint8_t edpt_find_opened(uint8_t dev_addr, uint8_t ep_num, uint8_t ep_dir) { +TU_ATTR_ALWAYS_INLINE static inline uint8_t edpt_find_opened(uint8_t dev_addr, uint8_t ep_num, uint8_t ep_dir, + bool include_closing) { for (uint8_t i = 0; i < (uint8_t)CFG_TUH_DWC2_ENDPOINT_MAX; i++) { const hcd_endpoint_t *edpt = &_hcd_data.edpt[i]; const dwc2_channel_char_t hcchar_bm = edpt->hcchar_bm; - if (hcchar_bm.enable && hcchar_bm.dev_addr == dev_addr && hcchar_bm.ep_num == ep_num && + if (hcchar_bm.enable && (include_closing || !edpt->closing) && hcchar_bm.dev_addr == dev_addr && + hcchar_bm.ep_num == ep_num && (ep_num == 0 || hcchar_bm.ep_dir == ep_dir)) { return i; } @@ -355,13 +424,13 @@ TU_ATTR_ALWAYS_INLINE static inline uint8_t cal_next_pid(uint8_t pid, uint8_t pa static void dfifo_host_init(uint8_t rhport, bool is_hs_phy) { const dwc2_controller_t* dwc2_controller = &_dwc2_controller[rhport]; dwc2_regs_t* dwc2 = DWC2_REG(rhport); - const dwc2_ghwcfg2_t ghwcfg2 = {.value = dwc2->ghwcfg2}; + const uint8_t channel_count = dwc2_channel_count(dwc2); // Scatter/Gather DMA mode is not yet supported. Buffer DMA only need 1 words per channel const bool is_dma = dma_host_enabled(dwc2); uint16_t dfifo_top = dwc2_controller->otg_dfifo_depth; if (is_dma) { - dfifo_top -= ghwcfg2.num_host_ch; + dfifo_top -= channel_count; } // fixed allocation for now, improve later: @@ -377,13 +446,12 @@ static void dfifo_host_init(uint8_t rhport, bool is_hs_phy) { } uint16_t nptxfsiz = 2 * nptx_largest; - uint16_t rxfsiz = 2 * (ptx_largest + 2) + ghwcfg2.num_host_ch; + uint16_t rxfsiz = 2 * (ptx_largest + 2) + channel_count; TU_ASSERT(dfifo_top >= (nptxfsiz + rxfsiz),); uint16_t ptxfsiz = dfifo_top - (nptxfsiz + rxfsiz); dwc2->gdfifocfg = (dfifo_top << GDFIFOCFG_EPINFOBASE_SHIFT) | dfifo_top; - dfifo_top -= rxfsiz; dwc2->grxfsiz = rxfsiz; dfifo_top -= nptxfsiz; @@ -567,7 +635,7 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, const tusb_desc_endpoint_t* edpt->next_pid = HCTSIZ_PID_DATA0; switch (desc_ep->bmAttributes.xfer) { case TUSB_XFER_ISOCHRONOUS: - edpt->uframe_interval = 1 << (desc_ep->bInterval - 1); + edpt->uframe_interval = 1u << (desc_ep->bInterval - 1); if (bus_info.speed == TUSB_SPEED_FULL) { edpt->uframe_interval <<= 3; } @@ -575,7 +643,7 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, const tusb_desc_endpoint_t* case TUSB_XFER_INTERRUPT: if (bus_info.speed == TUSB_SPEED_HIGH) { - edpt->uframe_interval = 1 << (desc_ep->bInterval - 1); + edpt->uframe_interval = 1u << (desc_ep->bInterval - 1); } else { edpt->uframe_interval = desc_ep->bInterval << 3; } @@ -585,6 +653,13 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, const tusb_desc_endpoint_t* break; } + if (channel_is_periodic(edpt->hcchar)) { + // HFNUM cannot distinguish elapsed periods longer than one counter cycle. USB permits the host to provide a + // shorter period, so bound the selected period to the history available from HFNUM. + const uint32_t ucount = (rh_speed == TUSB_SPEED_HIGH) ? 1u : 8u; + edpt->uframe_interval = tu_min32(edpt->uframe_interval, HCD_FRAME_COUNT * ucount); + } + return true; } @@ -592,7 +667,7 @@ bool hcd_edpt_close(uint8_t rhport, uint8_t daddr, uint8_t ep_addr) { dwc2_regs_t *dwc2 = DWC2_REG(rhport); const uint8_t ep_num = tu_edpt_number(ep_addr); const uint8_t ep_dir = tu_edpt_dir(ep_addr); - const uint8_t ep_id = edpt_find_opened(daddr, ep_num, ep_dir); + const uint8_t ep_id = edpt_find_opened(daddr, ep_num, ep_dir, true); TU_ASSERT(ep_id < CFG_TUH_DWC2_ENDPOINT_MAX); edpt_close(dwc2, ep_id); @@ -607,7 +682,10 @@ static void channel_xfer_out_wrapup(dwc2_regs_t* dwc2, uint8_t ch_id) { hcd_endpoint_t* edpt = &_hcd_data.edpt[xfer->ep_id]; const dwc2_channel_tsize_t hctsiz = {.value = channel->hctsiz}; - edpt->next_pid = hctsiz.pid; // save PID + const dwc2_channel_char_t hcchar = {.value = channel->hcchar}; + if (hcchar.ep_type != HCCHAR_EPTYPE_ISOCHRONOUS) { + edpt->next_pid = hctsiz.pid; // save PID + } /* Since hctsiz.xfersize field reflects the number of bytes transferred via the AHB, not the USB) * For IN: we can use hctsiz.xfersize as remaining bytes. @@ -616,7 +694,6 @@ static void channel_xfer_out_wrapup(dwc2_regs_t* dwc2, uint8_t ch_id) { * transfer was halted before its normal completion. */ const uint16_t remain_packets = hctsiz.packet_count; - const dwc2_channel_char_t hcchar = {.value = channel->hcchar}; const uint16_t total_packets = cal_packet_count(edpt->buflen, hcchar.ep_size); const uint16_t actual_bytes = (total_packets - remain_packets) * hcchar.ep_size; @@ -626,20 +703,26 @@ static void channel_xfer_out_wrapup(dwc2_regs_t* dwc2, uint8_t ch_id) { edpt->buflen -= actual_bytes; } -static bool channel_xfer_start(dwc2_regs_t* dwc2, uint8_t ch_id) { +#if CFG_TUH_DWC2_SLAVE_ENABLE +static bool channel_txfifo_write(dwc2_regs_t* dwc2, uint8_t ch_id, bool is_periodic); +#endif +static void periodic_xfer_defer(dwc2_regs_t* dwc2, hcd_endpoint_t* edpt, uint32_t uframe_countdown); + +static bool channel_xfer_start(dwc2_regs_t* dwc2, uint8_t ch_id, bool defer_periodic_out) { hcd_xfer_t* xfer = &_hcd_data.xfer[ch_id]; hcd_endpoint_t* edpt = &_hcd_data.edpt[xfer->ep_id]; dwc2_channel_char_t* hcchar_bm = &edpt->hcchar_bm; dwc2_channel_t* channel = &dwc2->channel[ch_id]; bool const is_period = channel_is_periodic(edpt->hcchar); - +#if CFG_TUH_DWC2_SLAVE_ENABLE + const uint8_t saved_pid = edpt->next_pid; + const uint8_t saved_do_ping = edpt->next_do_ping; +#endif + uint16_t periodic_frame = 0; // clear previous state xfer->fifo_bytes = 0; // hchar: restore but don't enable yet - if (is_period) { - hcchar_bm->odd_frame = 1 - (dwc2->hfnum & 1); // transfer on next frame - } channel->hcchar = (edpt->hcchar & ~HCCHAR_CHENA); // hctsiz: zero length packet still count as 1 @@ -655,15 +738,17 @@ static bool channel_xfer_start(dwc2_regs_t* dwc2, uint8_t ch_id) { channel->hctsiz = hctsiz.value; edpt->next_do_ping = 0; - // pre-calculate next PID based on packet count, adjusted in transfer complete interrupt if short packet + // Single-transaction isochronous endpoints always use DATA0. Pre-calculate the next PID for other endpoints, + // adjusted in the transfer-complete interrupt if a short packet is received. if (hcchar_bm->ep_num == 0) { edpt->next_pid = HCTSIZ_PID_DATA1; // control data and status stage always start with DATA1 - } else { + } else if (hcchar_bm->ep_type != HCCHAR_EPTYPE_ISOCHRONOUS) { edpt->next_pid = cal_next_pid(edpt->next_pid, packet_count); } channel->hcsplt = edpt->hcsplt; channel->hcint = 0xFFFFFFFFU; // clear all channel interrupts + dwc2->gintmsk |= GINTSTS_HCINT; if (dma_host_enabled(dwc2)) { channel->hcintmsk = HCINT_HALTED; @@ -672,13 +757,19 @@ static bool channel_xfer_start(dwc2_regs_t* dwc2, uint8_t ch_id) { channel->hcdma = (uint32_t) edpt->buffer; if (hcchar_bm->ep_dir == TUSB_DIR_IN) { - channel_send_in_token(dwc2, channel); + periodic_frame = channel_send_in_token(dwc2, channel, is_period); } else { hcd_dcache_clean(edpt->buffer, edpt->buflen); - channel->hcchar |= HCCHAR_CHENA; + periodic_frame = channel_enable(dwc2, channel, is_period); + } + } +#if CFG_TUH_DWC2_SLAVE_ENABLE + else { + uint32_t hcintmsk = HCINT_NAK | HCINT_XACT_ERR | HCINT_STALL | + HCINT_XFER_COMPLETE | HCINT_DATATOGGLE_ERR; + if (is_period) { + hcintmsk |= HCINT_FARME_OVERRUN; } - } else { - uint32_t hcintmsk = HCINT_NAK | HCINT_XACT_ERR | HCINT_STALL | HCINT_XFER_COMPLETE | HCINT_DATATOGGLE_ERR; if (hcchar_bm->ep_dir == TUSB_DIR_IN) { hcintmsk |= HCINT_BABBLE_ERR | HCINT_DATATOGGLE_ERR | HCINT_ACK; } else { @@ -696,16 +787,36 @@ static bool channel_xfer_start(dwc2_regs_t* dwc2, uint8_t ch_id) { // IN Token. If we got NAK, we have to re-enable the channel again in the interrupt. Due to the way usbh stack only // call hcd_edpt_xfer() once, we will need to manage de-allocate/re-allocate IN channel dynamically. if (hcchar_bm->ep_dir == TUSB_DIR_IN) { - channel_send_in_token(dwc2, channel); + periodic_frame = channel_send_in_token(dwc2, channel, is_period); } else { - channel->hcchar |= HCCHAR_CHENA; - if (edpt->buflen > 0) { - // To prevent conflict with other channel, we will enable periodic/non-periodic FIFO empty interrupt accordingly - // And write packet in the interrupt handler + // The final FIFO word creates the OUT request. Keep CHENA and that write + // atomic with respect to this controller's ISR. + // This region never waits for FIFO or queue space. + const uint32_t gahbcfg = dwc2->gahbcfg; + dwc2->gahbcfg = gahbcfg & ~GAHBCFG_GINT; + if (defer_periodic_out && is_period) { + const dwc2_hfnum_t hfnum = {.value = dwc2->hfnum}; + if (hfnum.remainning < DWC2_PERIODIC_OUT_MIN_FRREM) { + edpt->next_pid = saved_pid; + edpt->next_do_ping = saved_do_ping; + dwc2->gahbcfg = gahbcfg; + return false; + } + } + periodic_frame = channel_enable(dwc2, channel, is_period); + if (edpt->buflen > 0 && channel_txfifo_write(dwc2, ch_id, is_period)) { + // The FIFO-empty interrupt handles only work that did not fit in the + // initial synchronous write. dwc2->gintmsk |= (is_period ? GINTSTS_PTX_FIFO_EMPTY : GINTSTS_NPTX_FIFO_EMPTY); } + dwc2->gahbcfg = gahbcfg; } } +#endif + + if (is_period && defer_periodic_out) { + edpt->periodic_frame = periodic_frame; + } return true; } @@ -717,8 +828,48 @@ static bool edpt_xfer_kickoff(dwc2_regs_t* dwc2, uint8_t ep_id) { hcd_xfer_t* xfer = &_hcd_data.xfer[ch_id]; xfer->ep_id = ep_id; xfer->result = XFER_RESULT_INVALID; + hcd_endpoint_t* edpt = &_hcd_data.edpt[ep_id]; + const bool result = channel_xfer_start(dwc2, ch_id, true); + if (!result) { + channel_dealloc(dwc2, ch_id); + periodic_xfer_defer(dwc2, edpt, 0); + return true; + } + if (channel_is_periodic(_hcd_data.edpt[ep_id].hcchar)) { + edpt->periodic_phase = 1; + edpt->xfer_pending = 0; + } + return result; +} + +static uint32_t periodic_xfer_countdown(dwc2_regs_t* dwc2, hcd_endpoint_t const* edpt) { + const uint32_t ucount = (hprt_speed_get(dwc2) == TUSB_SPEED_HIGH) ? 1u : 8u; + const uint16_t frame = (uint16_t) (dwc2->hfnum & HCD_FRAME_NUMBER_MASK); + const uint16_t elapsed_frames = (uint16_t) (frame - edpt->periodic_frame) & HCD_FRAME_NUMBER_MASK; + const uint32_t elapsed_uframes = (uint32_t) elapsed_frames * ucount; - return channel_xfer_start(dwc2, ch_id); + if (elapsed_uframes < edpt->uframe_interval) { + return edpt->uframe_interval - elapsed_uframes - ucount; + } + + // The service opportunity was missed. Keep the established phase and use + // the next interval rather than starting a new interval from this request. + return edpt->uframe_interval - (elapsed_uframes % edpt->uframe_interval) - ucount; +} + +static void periodic_xfer_defer(dwc2_regs_t* dwc2, hcd_endpoint_t* edpt, uint32_t uframe_countdown) { + const uint32_t gahbcfg = dwc2->gahbcfg; + dwc2->gahbcfg = gahbcfg & ~GAHBCFG_GINT; + + edpt->uframe_countdown = uframe_countdown; + edpt->xfer_pending = 1; + + if (0 == (dwc2->gintmsk & GINTMSK_SOFM)) { + dwc2->gintsts = GINTSTS_SOF; + dwc2->gintmsk |= GINTMSK_SOFM; + } + + dwc2->gahbcfg = gahbcfg; } bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) { @@ -726,10 +877,10 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * const uint8_t ep_num = tu_edpt_number(ep_addr); const uint8_t ep_dir = tu_edpt_dir(ep_addr); - uint8_t ep_id = edpt_find_opened(dev_addr, ep_num, ep_dir); - TU_ASSERT(ep_id < CFG_TUH_DWC2_ENDPOINT_MAX); + uint8_t ep_id = edpt_find_opened(dev_addr, ep_num, ep_dir, false); + TU_VERIFY(ep_id < CFG_TUH_DWC2_ENDPOINT_MAX); hcd_endpoint_t *edpt = &_hcd_data.edpt[ep_id]; - TU_VERIFY(edpt->closing == 0); // skip if endpoint is closing + TU_VERIFY(edpt->closing == 0 && edpt->aborting == 0); // skip if endpoint is closing or aborting edpt->buffer = buffer; edpt->buflen = buflen; @@ -739,6 +890,26 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * edpt->hcchar_bm.ep_dir = ep_dir; } + if (channel_is_periodic(edpt->hcchar)) { + const uint32_t ucount = (hprt_speed_get(dwc2) == TUSB_SPEED_HIGH) ? 1u : 8u; +#if CFG_TUH_DWC2_SLAVE_ENABLE + // Establish a slower slave-mode OUT schedule from SOF. bInterval=1 must be queued immediately to avoid + // losing every other service opportunity. + if (!dma_host_enabled(dwc2) && ep_dir == TUSB_DIR_OUT && !edpt->periodic_phase && + edpt->uframe_interval > ucount) { + periodic_xfer_defer(dwc2, edpt, 0); + return true; + } +#endif + if (edpt->periodic_phase && edpt->uframe_interval > ucount) { + const uint32_t countdown = periodic_xfer_countdown(dwc2, edpt); + if (countdown > 0) { + periodic_xfer_defer(dwc2, edpt, countdown); + return true; + } + } + } + return edpt_xfer_kickoff(dwc2, ep_id); } @@ -748,11 +919,39 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { dwc2_regs_t* dwc2 = DWC2_REG(rhport); const uint8_t ep_num = tu_edpt_number(ep_addr); const uint8_t ep_dir = tu_edpt_dir(ep_addr); - const uint8_t ep_id = edpt_find_opened(dev_addr, ep_num, ep_dir); + const uint8_t ep_id = edpt_find_opened(dev_addr, ep_num, ep_dir, false); TU_VERIFY(ep_id < CFG_TUH_DWC2_ENDPOINT_MAX); + hcd_endpoint_t* edpt = &_hcd_data.edpt[ep_id]; + + hcd_int_disable(rhport); + + const bool xfer_pending = edpt->xfer_pending; + if (xfer_pending) { + edpt->xfer_pending = 0; + edpt->uframe_countdown = 0; + } + + if (xfer_pending) { + hcd_int_enable(rhport); + return true; + } + + // A periodic DMA channel must halt naturally at the next service boundary. Prevent a replacement transfer until the + // halt ISR retires the channel, and suppress completion for the aborted transfer. + if (dma_host_enabled(dwc2) && channel_is_periodic(edpt->hcchar)) { + const uint8_t ch_id = channel_find_enabled(dwc2, dev_addr, ep_num, ep_dir); + if (ch_id < 16) { + hcd_xfer_t* xfer = &_hcd_data.xfer[ch_id]; + edpt->aborting = 1; + xfer->aborting = true; + hcd_int_enable(rhport); + return true; + } + } - // hcd_int_disable(rhport); + hcd_int_enable(rhport); + // Channel disable may wait for request-queue space in slave mode. // Find enabled channeled and disable it, channel will be de-allocated in the interrupt handler const uint8_t ch_id = channel_find_enabled(dwc2, dev_addr, ep_num, ep_dir); if (ch_id < 16) { @@ -760,15 +959,13 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { channel_disable(dwc2, channel); } - // hcd_int_enable(rhport); - return true; } // Submit a special transfer to send 8-byte Setup Packet, when complete hcd_event_xfer_complete() must be invoked bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, const uint8_t setup_packet[8]) { - uint8_t ep_id = edpt_find_opened(dev_addr, 0, TUSB_DIR_OUT); - TU_ASSERT(ep_id < CFG_TUH_DWC2_ENDPOINT_MAX); // no opened endpoint + uint8_t ep_id = edpt_find_opened(dev_addr, 0, TUSB_DIR_OUT, false); + TU_VERIFY(ep_id < CFG_TUH_DWC2_ENDPOINT_MAX); // endpoint can close asynchronously on disconnect hcd_endpoint_t* edpt = &_hcd_data.edpt[ep_id]; edpt->next_pid = HCTSIZ_PID_SETUP; @@ -780,7 +977,7 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { (void) rhport; const uint8_t ep_num = tu_edpt_number(ep_addr); const uint8_t ep_dir = tu_edpt_dir(ep_addr); - const uint8_t ep_id = edpt_find_opened(dev_addr, ep_num, ep_dir); + const uint8_t ep_id = edpt_find_opened(dev_addr, ep_num, ep_dir, false); TU_VERIFY(ep_id < CFG_TUH_DWC2_ENDPOINT_MAX); hcd_endpoint_t* edpt = &_hcd_data.edpt[ep_id]; @@ -809,7 +1006,7 @@ static void channel_xfer_in_retry(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t hci if (xfer->period_split_nyet_count < HCD_XFER_PERIOD_SPLIT_NYET_MAX) { hcchar.odd_frame = 1 - (dwc2->hfnum & 1); // transfer on next frame channel->hcchar = hcchar.value; - channel_send_in_token(dwc2, channel); + channel_send_in_token(dwc2, channel, false); return; } else { // too many NYET, de-allocate channel with below code @@ -822,23 +1019,20 @@ static void channel_xfer_in_retry(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t hci // retry on next frame if bInterval is 1 hcchar.odd_frame = 1 - (dwc2->hfnum & 1); channel->hcchar = hcchar.value; - channel_send_in_token(dwc2, channel); + channel_send_in_token(dwc2, channel, false); } else { // otherwise, de-allocate channel, enable SOF set frame counter for later transfer const dwc2_channel_tsize_t hctsiz = {.value = channel->hctsiz}; - edpt->next_pid = hctsiz.pid; // save PID - edpt->uframe_countdown = edpt->uframe_interval - ucount; - // enable SOF interrupt if not already enabled - if (0 == (dwc2->gintmsk & GINTMSK_SOFM)) { - dwc2->gintsts = GINTSTS_SOF; - dwc2->gintmsk |= GINTMSK_SOFM; + if (hcchar.ep_type != HCCHAR_EPTYPE_ISOCHRONOUS) { + edpt->next_pid = hctsiz.pid; // save PID } + periodic_xfer_defer(dwc2, edpt, periodic_xfer_countdown(dwc2, edpt)); // already halted, de-allocate channel (called from DMA isr) channel_dealloc(dwc2, ch_id); } } else { // for control/bulk: retry immediately - channel_send_in_token(dwc2, channel); + channel_send_in_token(dwc2, channel, false); } } @@ -873,6 +1067,13 @@ static void handle_rxflvl_irq(uint8_t rhport) { // In packet received, pop this entry --> ACK interrupt const uint16_t byte_count = grxstsp.byte_count; hcd_xfer_t* xfer = &_hcd_data.xfer[ch_id]; + if (!xfer->allocated) { + // Discard data for a channel retired by disconnect. + for (uint16_t count = 0; count < byte_count; count += sizeof(uint32_t)) { + (void) dwc2->fifo[0][0]; + } + break; + } TU_ASSERT(xfer->ep_id < CFG_TUH_DWC2_ENDPOINT_MAX,); hcd_endpoint_t* edpt = &_hcd_data.edpt[xfer->ep_id]; @@ -902,38 +1103,50 @@ static void handle_rxflvl_irq(uint8_t rhport) { } } -// return true if there is still pending data and need more ISR +// Return true if data remains for a later FIFO-empty interrupt. +static bool channel_txfifo_write(dwc2_regs_t* dwc2, uint8_t ch_id, bool is_periodic) { + hcd_xfer_t* xfer = &_hcd_data.xfer[ch_id]; + dwc2_channel_t* channel = &dwc2->channel[ch_id]; + const dwc2_channel_char_t hcchar = {.value = channel->hcchar}; + TU_ASSERT(xfer->ep_id < CFG_TUH_DWC2_ENDPOINT_MAX); + hcd_endpoint_t* edpt = &_hcd_data.edpt[xfer->ep_id]; + const dwc2_channel_tsize_t hctsiz = {.value = channel->hctsiz}; + const uint16_t remain_packets = hctsiz.packet_count; + + for (uint16_t i = 0; i < remain_packets; i++) { + const uint16_t remain_bytes = edpt->buflen - xfer->fifo_bytes; + const uint16_t xact_bytes = tu_min16(remain_bytes, hcchar.ep_size); + + // The packet's last FIFO word creates its request-queue entry. + // HNPTXSTS differs by one request-queue bit, which is outside these fields. + const dwc2_hptxsts_t txsts = {.value = (is_periodic ? dwc2->hptxsts : dwc2->hnptxsts)}; + if ((xact_bytes > (txsts.fifo_available << 2)) || (txsts.req_queue_available == 0)) { + return true; + } + + tu_hwfifo_write(dwc2->fifo[ch_id], edpt->buffer + xfer->fifo_bytes, xact_bytes, NULL); + xfer->fifo_bytes += xact_bytes; + } + + return false; +} + +// Return true if at least one matching channel needs another interrupt. static bool handle_txfifo_empty(dwc2_regs_t* dwc2, bool is_periodic) { const uint8_t max_channel = dwc2_channel_count(dwc2); for (uint8_t ch_id = 0; ch_id < max_channel; ch_id++) { + hcd_xfer_t* xfer = &_hcd_data.xfer[ch_id]; dwc2_channel_t* channel = &dwc2->channel[ch_id]; const dwc2_channel_char_t hcchar = {.value = channel->hcchar}; - // skip writing to FIFO if channel is expecting halted. - if (0 == (channel->hcintmsk & HCINT_HALTED) && (hcchar.ep_dir == TUSB_DIR_OUT)) { - hcd_xfer_t *xfer = &_hcd_data.xfer[ch_id]; - TU_ASSERT(xfer->ep_id < CFG_TUH_DWC2_ENDPOINT_MAX); - hcd_endpoint_t* edpt = &_hcd_data.edpt[xfer->ep_id]; - const dwc2_channel_tsize_t hctsiz = {.value = channel->hctsiz}; - const uint16_t remain_packets = hctsiz.packet_count; - for (uint16_t i = 0; i < remain_packets; i++) { - const uint16_t remain_bytes = edpt->buflen - xfer->fifo_bytes; - const uint16_t xact_bytes = tu_min16(remain_bytes, hcchar.ep_size); - - // skip if there is not enough space in FIFO and RequestQueue. - // Packet's last word written to FIFO will trigger a request queue - // Use period txsts for both p/np to get request queue space available (1-bit difference, it is small enough) - const dwc2_hptxsts_t txsts = {.value = (is_periodic ? dwc2->hptxsts : dwc2->hnptxsts)}; - if ((xact_bytes > (txsts.fifo_available << 2)) || (txsts.req_queue_available == 0)) { - return true; - } - - tu_hwfifo_write(dwc2->fifo[ch_id], edpt->buffer + xfer->fifo_bytes, xact_bytes, NULL); - xfer->fifo_bytes += xact_bytes; + if (xfer->allocated && channel_is_periodic(hcchar.value) == is_periodic && + 0 == (channel->hcintmsk & HCINT_HALTED) && hcchar.ep_dir == TUSB_DIR_OUT) { + if (channel_txfifo_write(dwc2, ch_id, is_periodic)) { + return true; } } } - return false; // no channel has pending data + return false; } static bool handle_channel_in_slave(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t hcint) { @@ -951,7 +1164,8 @@ static bool handle_channel_in_slave(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t h // } if (hcint & HCINT_XFER_COMPLETE) { - if (edpt->hcchar_bm.ep_num != 0) { + if (edpt->hcchar_bm.ep_num != 0 && + edpt->hcchar_bm.ep_type != HCCHAR_EPTYPE_ISOCHRONOUS) { edpt->next_pid = hctsiz.pid; // save pid (already toggled) } @@ -964,6 +1178,17 @@ static bool handle_channel_in_slave(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t h xfer->result = XFER_RESULT_SUCCESS; } + if (channel_is_periodic(channel->hcchar) && remain_packets == 0) { + // The core has already halted a completed periodic IN channel. Complete + // it now so the next interval can be submitted without another halt IRQ. + is_done = true; + } else { + channel_disable(dwc2, channel); + } + } else if (hcint & HCINT_FARME_OVERRUN) { + if (edpt->hcchar_bm.ep_type == HCCHAR_EPTYPE_ISOCHRONOUS) { + xfer->result = XFER_RESULT_FAILED; + } channel_disable(dwc2, channel); } else if (hcint & (HCINT_XACT_ERR | HCINT_BABBLE_ERR | HCINT_STALL)) { if (hcint & HCINT_STALL) { @@ -1001,7 +1226,7 @@ static bool handle_channel_in_slave(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t h channel->hcintmsk |= HCINT_NYET; hcsplt.split_compl = 1; channel->hcsplt = hcsplt.value; - channel_send_in_token(dwc2, channel); + channel_send_in_token(dwc2, channel, false); } else { // do nothing for complete split with DATA, this will trigger XferComplete and handled there } @@ -1012,7 +1237,7 @@ static bool handle_channel_in_slave(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t h // still more packet to receive, also reset to start split hcsplt.split_compl = 0; channel->hcsplt = hcsplt.value; - channel_send_in_token(dwc2, channel); + channel_send_in_token(dwc2, channel, false); } } } else if (hcint & HCINT_HALTED) { @@ -1058,6 +1283,12 @@ static bool handle_channel_out_slave(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t } else if (hcint & HCINT_STALL) { xfer->result = XFER_RESULT_STALLED; channel_disable(dwc2, channel); + } else if (hcint & HCINT_FARME_OVERRUN) { + channel_xfer_out_wrapup(dwc2, ch_id); + if (edpt->hcchar_bm.ep_type == HCCHAR_EPTYPE_ISOCHRONOUS) { + xfer->result = XFER_RESULT_FAILED; + } + channel_disable(dwc2, channel); } else if (hcint & HCINT_NYET) { xfer->err_count = 0; if (hcsplt.split_en == 1u) { @@ -1093,7 +1324,7 @@ static bool handle_channel_out_slave(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t is_done = true; } else { // Got here due to NAK or NYET - TU_ASSERT(channel_xfer_start(dwc2, ch_id)); + TU_ASSERT(channel_xfer_start(dwc2, ch_id, false)); } } else if (hcint & HCINT_ACK) { xfer->err_count = 0; @@ -1145,9 +1376,13 @@ static bool handle_channel_in_dma(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t hci if (xfer->closing) { is_done = true; } else { - channel_send_in_token(dwc2, channel); + channel_send_in_token(dwc2, channel, false); } } else if (hcint & (HCINT_XFER_COMPLETE | HCINT_STALL | HCINT_BABBLE_ERR)) { + if (edpt->hcchar_bm.ep_num != 0 && (hcint & HCINT_XFER_COMPLETE)) { + edpt->next_pid = hctsiz.pid; // save pid (already toggled) + } + const uint16_t remain_bytes = (uint16_t) hctsiz.xfer_size; const uint16_t remain_packets = hctsiz.packet_count; const uint16_t actual_len = edpt->buflen - remain_bytes; @@ -1206,7 +1441,7 @@ static bool handle_channel_in_dma(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t hci hcchar.odd_frame = 1 - (dwc2->hfnum & 1); // transfer on next frame channel->hcchar = hcchar.value; } - channel_send_in_token(dwc2, channel); + channel_send_in_token(dwc2, channel, false); } } else if (hcint & (HCINT_NAK | HCINT_DATATOGGLE_ERR)) { xfer->err_count = 0; @@ -1223,8 +1458,12 @@ static bool handle_channel_in_dma(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t hci channel_xfer_in_retry(dwc2, ch_id, hcint); } } else if (hcint & HCINT_FARME_OVERRUN) { - // retry start-split in next binterval - channel_xfer_in_retry(dwc2, ch_id, hcint); + if (hcchar.ep_type == HCCHAR_EPTYPE_ISOCHRONOUS) { + xfer->result = XFER_RESULT_FAILED; + is_done = true; + } else { + channel_xfer_in_retry(dwc2, ch_id, hcint); + } } if (xfer->closing == 1) { @@ -1253,7 +1492,7 @@ static bool handle_channel_out_dma(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t hc if (xfer->closing) { is_done = true; } else { - channel_xfer_start(dwc2, ch_id); + channel_xfer_start(dwc2, ch_id, false); } } else if (hcint & (HCINT_XFER_COMPLETE | HCINT_STALL)) { is_done = true; @@ -1267,30 +1506,38 @@ static bool handle_channel_out_dma(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t hc } channel->hcintmsk &= ~HCINT_ACK; } else if (hcint & HCINT_XACT_ERR) { - if (hcint & (HCINT_NAK | HCINT_NYET | HCINT_ACK)) { - xfer->err_count = 0; - // clean up transfer so far and start again - channel_xfer_out_wrapup(dwc2, ch_id); - channel_xfer_start(dwc2, ch_id); - } else { - xfer->err_count++; - if (xfer->err_count >= HCD_XFER_ERROR_MAX) { - xfer->result = XFER_RESULT_FAILED; - is_done = true; - } else { - // Rewind, then retry the start-split. Non-periodic SPLIT throttles via channel_disable + re-arm on - // the halt (immediate re-fire exhausts the retry budget; the disable gives the hub TT a recovery - // gap, like slave). Periodic split is excluded: channel_disable() is a no-op for it, so the halt - // never fires and the channel would wedge. Non-split re-inits immediately (Programming Guide 5.1.2.3). - channel_xfer_out_wrapup(dwc2, ch_id); - if (hcsplt.split_en && !channel_is_periodic(channel->hcchar)) { - xfer->retry_disabled = 1; - channel_disable(dwc2, channel); - } else { - channel_xfer_start(dwc2, ch_id); - } - } - } + if (hcint & (HCINT_NAK | HCINT_NYET | HCINT_ACK)) { + xfer->err_count = 0; + // clean up transfer so far and start again + channel_xfer_out_wrapup(dwc2, ch_id); + channel_xfer_start(dwc2, ch_id, false); + } else { + xfer->err_count++; + if (xfer->err_count >= HCD_XFER_ERROR_MAX) { + xfer->result = XFER_RESULT_FAILED; + is_done = true; + } else { + // Rewind, then retry the start-split. Non-periodic SPLIT throttles via channel_disable + re-arm on + // the halt (immediate re-fire exhausts the retry budget; the disable gives the hub TT a recovery + // gap, like slave). Periodic split is excluded: channel_disable() is a no-op for it, so the halt + // never fires and the channel would wedge. Non-split re-inits immediately (Programming Guide 5.1.2.3). + channel_xfer_out_wrapup(dwc2, ch_id); + if (hcsplt.split_en && !channel_is_periodic(channel->hcchar)) { + xfer->retry_disabled = 1; + channel_disable(dwc2, channel); + } else { + channel_xfer_start(dwc2, ch_id, false); + } + } + } + } else if (hcint & HCINT_FARME_OVERRUN) { + channel_xfer_out_wrapup(dwc2, ch_id); + if (edpt->hcchar_bm.ep_type == HCCHAR_EPTYPE_ISOCHRONOUS) { + xfer->result = XFER_RESULT_FAILED; + is_done = true; + } else { + channel_xfer_start(dwc2, ch_id, false); + } } else if (hcint & HCINT_NYET) { if (hcsplt.split_en && hcsplt.split_compl) { // split not yet mean hub has no data, retry complete split @@ -1311,7 +1558,7 @@ static bool handle_channel_out_dma(dwc2_regs_t* dwc2, uint8_t ch_id, uint32_t hc // Non-split OUT NAK is core-handled (5.1.2.2), so this is split-only. xfer->err_count = 0; channel_xfer_out_wrapup(dwc2, ch_id); - channel_xfer_start(dwc2, ch_id); + channel_xfer_start(dwc2, ch_id, false); } if (xfer->closing == 1) { @@ -1339,7 +1586,29 @@ static void handle_channel_irq(uint8_t rhport, bool in_isr) { dwc2_channel_char_t hcchar = {.value = channel->hcchar}; const uint32_t hcint = channel->hcint; - channel->hcint = hcint; // clear interrupt + // Slave handlers process one cause per pass. If ChHltd arrived with + // another cause, leave it pending so the next pass retires the halt. + const uint32_t hcint_clear = (!is_dma && (hcint & ~HCINT_HALTED)) ? (hcint & ~HCINT_HALTED) : hcint; + channel->hcint = hcint_clear; + + if (is_dma && xfer->aborting && (hcint & HCINT_HALTED)) { + hcd_endpoint_t* edpt = &_hcd_data.edpt[xfer->ep_id]; + const bool closing = xfer->closing; + // channel_xfer_start() predicts the PID after all requested packets; + // an aborted transfer may have completed fewer. + if (hcchar.ep_type != HCCHAR_EPTYPE_ISOCHRONOUS) { + const dwc2_channel_tsize_t hctsiz = {.value = channel->hctsiz}; + edpt->next_pid = hctsiz.pid; + } + xfer->aborting = false; + channel_dealloc(dwc2, ch_id); + if (closing) { + edpt_dealloc(edpt); + } else { + edpt->aborting = 0; + } + continue; + } bool is_done = false; if (is_dma) { @@ -1392,15 +1661,17 @@ static bool handle_sof_irq(uint8_t rhport, bool in_isr) { for(uint8_t ep_id = 0; ep_id < CFG_TUH_DWC2_ENDPOINT_MAX; ep_id++) { hcd_endpoint_t *edpt = &_hcd_data.edpt[ep_id]; if (edpt->closing == 0) { - if (edpt->hcchar_bm.enable && channel_is_periodic(edpt->hcchar) && edpt->uframe_countdown > 0) { - edpt->uframe_countdown -= tu_min32(ucount, edpt->uframe_countdown); + if (edpt->hcchar_bm.enable && channel_is_periodic(edpt->hcchar) && edpt->xfer_pending) { + if (edpt->uframe_countdown > 0) { + edpt->uframe_countdown -= tu_min32(ucount, edpt->uframe_countdown); + } if (edpt->uframe_countdown == 0) { if (!edpt_xfer_kickoff(dwc2, ep_id)) { edpt->uframe_countdown = ucount; // failed to start, try again next frame } } - more_isr = true; + more_isr = more_isr || edpt->xfer_pending; } } } @@ -1520,25 +1791,23 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { } } - if (gintsts & GINTSTS_HPRTINT) { - // Host port interrupt: source is cleared in HPRT register - // TU_LOG1_HEX(dwc2->hprt); - handle_hprt_irq(rhport, in_isr); - } - - if (gintsts & GINTSTS_HCINT) { - // Host Channel interrupt: source is cleared in HCINT register - // must be handled after TX FIFO empty - handle_channel_irq(rhport, in_isr); - } - if (gintsts & GINTSTS_DISCINT) { - // Device disconnected dwc2->gintsts = GINTSTS_DISCINT; + channel_cleanup_on_disconnect(dwc2); + hcd_event_device_remove(rhport, in_isr); - if (0 == (dwc2->hprt & HPRT_CONN_STATUS)) { - hcd_event_device_remove(rhport, in_isr); + // A fast replug can be visible without a pending connect-detect interrupt. + const uint32_t hprt = dwc2->hprt; + if (!(hprt & HPRT_CONN_DETECT) && (hprt & HPRT_CONN_STATUS)) { + hcd_event_device_attach(rhport, in_isr); } + return; + } + + if (gintsts & GINTSTS_HPRTINT) { + // Host port interrupt: source is cleared in HPRT register + // TU_LOG1_HEX(dwc2->hprt); + handle_hprt_irq(rhport, in_isr); } #if CFG_TUH_DWC2_SLAVE_ENABLE @@ -1572,6 +1841,13 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { } } #endif + + // Draining the RxFIFO completion status can assert HCINT.XferCompl. Read + // the live status here so the completion is handled in this ISR invocation. + if ((dwc2->gintsts & dwc2->gintmsk) & GINTSTS_HCINT) { + handle_channel_irq(rhport, in_isr); + } + } #endif diff --git a/src/portable/template/dcd_template.c b/src/portable/template/dcd_template.c index 90c672d19..71be2024c 100644 --- a/src/portable/template/dcd_template.c +++ b/src/portable/template/dcd_template.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2018, hathach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2018, Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/template/hcd_template.c b/src/portable/template/hcd_template.c index d2f304407..658db7fd9 100644 --- a/src/portable/template/hcd_template.c +++ b/src/portable/template/hcd_template.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2023 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2023 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/ti/msp430x5xx/dcd_msp430x5xx.c b/src/portable/ti/msp430x5xx/dcd_msp430x5xx.c index 5f4b139d8..a734adb7d 100644 --- a/src/portable/ti/msp430x5xx/dcd_msp430x5xx.c +++ b/src/portable/ti/msp430x5xx/dcd_msp430x5xx.c @@ -1,26 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019-2020 William D. Jones - * Copyright (c) 2019-2020 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 William D. Jones + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/valentyusb/eptri/dcd_eptri.c b/src/portable/valentyusb/eptri/dcd_eptri.c index 1b555b3b7..68a993574 100644 --- a/src/portable/valentyusb/eptri/dcd_eptri.c +++ b/src/portable/valentyusb/eptri/dcd_eptri.c @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/valentyusb/eptri/dcd_eptri.h b/src/portable/valentyusb/eptri/dcd_eptri.h index 2fe74a712..fef8836c2 100644 --- a/src/portable/valentyusb/eptri/dcd_eptri.h +++ b/src/portable/valentyusb/eptri/dcd_eptri.h @@ -1,25 +1,6 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2019 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/wch/ch32_usbfs_reg.h b/src/portable/wch/ch32_usbfs_reg.h index 415a015dc..5b037281f 100644 --- a/src/portable/wch/ch32_usbfs_reg.h +++ b/src/portable/wch/ch32_usbfs_reg.h @@ -1,26 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024 Matthew Tran - * Copyright (c) 2024 hathach - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024 Matthew Tran + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -198,6 +179,14 @@ #endif #endif +// CH32V20x/V30x/F20x USBFS gives endpoint 3 a 1023-byte isochronous packet (CH32FV2x_V3xRM ch23: +// every endpoint is 64 B except EP3 = 1023 B, from EP3's 10-bit R16_UEP3_T_LEN field plus a single +// contiguous >=1023 B DMA buffer — NOT double-buffering, which only yields 2x64 B). +// CH32V103/X035/CH58x cap every endpoint at 64 B. dcd_ch32_usbfs.c reads this to size EP3's buffer. +#if CFG_TUSB_MCU == OPT_MCU_CH32V20X || CFG_TUSB_MCU == OPT_MCU_CH32V307 || CFG_TUSB_MCU == OPT_MCU_CH32F20X + #define CH32_USBFS_EP3_1023_BUFSIZE 1 +#endif + #ifdef __GNUC__ #pragma GCC diagnostic pop #endif diff --git a/src/portable/wch/ch32_usbhs_reg.h b/src/portable/wch/ch32_usbhs_reg.h index 87300b497..d176f0950 100644 --- a/src/portable/wch/ch32_usbhs_reg.h +++ b/src/portable/wch/ch32_usbhs_reg.h @@ -1,26 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024 Matthew Tran - * Copyright (c) 2024 hathach - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024 Matthew Tran + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ diff --git a/src/portable/wch/dcd_ch32_usbfs.c b/src/portable/wch/dcd_ch32_usbfs.c index ece9cde07..ec521224e 100644 --- a/src/portable/wch/dcd_ch32_usbfs.c +++ b/src/portable/wch/dcd_ch32_usbfs.c @@ -1,26 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024 Matthew Tran - * Copyright (c) 2024 hathach - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024 Matthew Tran + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -35,6 +16,17 @@ /* private defines */ #define EP_MAX (8) + // EP3 IN buffer size. CH32V20x/V30x/F20x USBFS support full-speed iso packets up to 1023 B on + // endpoint 3 (every other endpoint is 64 B); those parts set CH32_USBFS_EP3_1023_BUFSIZE in + // ch32_usbfs_reg.h. V103/X035/CH58x cap every endpoint at 64 B. Overridable per project. + #ifndef CFG_TUD_WCH_USBFS_EP3_BUFSIZE + #ifdef CH32_USBFS_EP3_1023_BUFSIZE + #define CFG_TUD_WCH_USBFS_EP3_BUFSIZE 1023 + #else + #define CFG_TUD_WCH_USBFS_EP3_BUFSIZE 64 + #endif + #endif + // Struct-based EP register access (uniform layout). CH58X has a different register map and // defines EP_DMA/EP_TX_LEN/EP_CTRL itself in ch32_usbfs_reg.h. #if CFG_TUSB_MCU == OPT_MCU_CH583 @@ -126,7 +118,7 @@ struct usb_xfer { static struct { bool ep0_tog; - bool isochronous[EP_MAX]; + bool isochronous[EP_MAX][2]; // per [ep][dir]: an ep number may be iso in one direction struct usb_xfer xfer[EP_MAX][2]; #ifdef CH32_USBFS_EP4_SHARES_EP0 // CH58X buffers laid out by hand so EP0/EP4 don't burn two unused buffer[] slots. EP0 and EP4 @@ -142,21 +134,23 @@ static struct { TU_ATTR_ALIGNED(4) uint8_t ep6_buffer[2][64]; TU_ATTR_ALIGNED(4) uint8_t ep7_buffer[2][64]; #else + // Every endpoint gets a 64-byte OUT + 64-byte IN buffer. TU_ATTR_ALIGNED(4) uint8_t buffer[EP_MAX][2][64]; - // EP3 IN gets an enlarged buffer for full-speed isochronous (packets up to 1023 B). + #if CFG_TUD_WCH_USBFS_EP3_BUFSIZE > 64 + // ...except EP3, which supports full-speed iso packets up to 1023 B on CH32V20x/V30x/F20x, so its + // IN buffer is enlarged (OUT stays 64 B; an OUT transfer >64 B on EP3 would overwrite queued IN). TU_ATTR_ALIGNED(4) struct { - // OUT transfers >64 bytes will overwrite queued IN data! uint8_t out[64]; - uint8_t in[1023]; + uint8_t in[CFG_TUD_WCH_USBFS_EP3_BUFSIZE]; uint8_t pad; } ep3_buffer; + #endif #endif } data; // DMA / copy buffer pointers per endpoint. The WCH USBFS buffer holds OUT (RX) at offset 0 and -// IN (TX) at +64; EP0 is half-duplex and reuses its OUT chunk for IN; EP3 has an enlarged IN -// buffer for throughput. On CH58X, EP0/EP4 share ep0_ep4_buffer and the regular endpoints use -// their own named buffer (see the struct above). +// IN (TX) at +64; EP0 is half-duplex and reuses its OUT chunk for IN. On CH58X, EP0/EP4 share +// ep0_ep4_buffer and the regular endpoints use their own named buffer (see the struct above). #ifdef CH32_USBFS_EP4_SHARES_EP0 // OUT base of the regular CH58X endpoints (EP1/2/3/5/6/7; EP0/EP4 share ep0_ep4_buffer). static inline uint8_t* ch58x_ep_buffer(uint8_t ep) { @@ -176,7 +170,9 @@ static inline uint32_t ep_dma_addr(uint8_t ep) { if (ep == 0 || ep == 4) { return (uint32_t) &data.ep0_ep4_buffer[0]; } // EP4 shares EP0's DMA return (uint32_t) ch58x_ep_buffer(ep); #else - if (ep == 3) { return (uint32_t) &data.ep3_buffer.out[0]; } + #if CFG_TUD_WCH_USBFS_EP3_BUFSIZE > 64 + if (ep == 3) { return (uint32_t) &data.ep3_buffer.out[0]; } // EP3 has an enlarged IN buffer + #endif return (uint32_t) &data.buffer[ep][0]; #endif } @@ -187,7 +183,9 @@ static inline uint8_t* ep_out_buf(uint8_t ep) { if (ep == 4) { return &data.ep0_ep4_buffer[64]; } return ch58x_ep_buffer(ep); #else + #if CFG_TUD_WCH_USBFS_EP3_BUFSIZE > 64 if (ep == 3) { return data.ep3_buffer.out; } + #endif return data.buffer[ep][TUSB_DIR_OUT]; #endif } @@ -199,7 +197,9 @@ static inline uint8_t* ep_in_buf(uint8_t ep) { return ch58x_ep_buffer(ep) + 64; // IN at +64 within the endpoint's 128-byte buffer #else if (ep == 0) { return data.buffer[0][TUSB_DIR_OUT]; } // EP0 half-duplex: IN reuses OUT chunk - if (ep == 3) { return data.ep3_buffer.in; } + #if CFG_TUD_WCH_USBFS_EP3_BUFSIZE > 64 + if (ep == 3) { return data.ep3_buffer.in; } // enlarged IN buffer for full-speed iso + #endif return data.buffer[ep][TUSB_DIR_IN]; #endif } @@ -221,9 +221,8 @@ static void update_in(uint8_t rhport, uint8_t ep, bool force) { if (force || xfer->len) { size_t len = TU_MIN(xfer->max_size, xfer->len); #if CFG_TUSB_MCU == OPT_MCU_CH583 - // Every CH58x endpoint buffer is 64 bytes. Isochronous (which would push max_size up to 1023) - // is refused in dcd_edpt_iso_alloc(), but some classes (e.g. video) ignore that result, so cap - // the copy here to guarantee we never write past the buffer into a neighbouring endpoint's. + // Every CH58x endpoint buffer is 64 bytes; cap the copy so an iso mps a class mistakenly set + // larger can't write past the buffer into a neighbouring endpoint's. len = TU_MIN(len, 64u); #endif memcpy(ep_in_buf(ep), xfer->buffer, len); @@ -235,7 +234,7 @@ static void update_in(uint8_t rhport, uint8_t ep, bool force) { if (ep == 0) { ep_tx_ctrl_set(0, USBFS_EP_T_RES_ACK | (data.ep0_tog ? USBFS_EP_T_TOG : 0)); data.ep0_tog = !data.ep0_tog; - } else if (data.isochronous[ep]) { + } else if (data.isochronous[ep][TUSB_DIR_IN]) { ep_tx_set_response(ep, USBFS_EP_T_RES_NYET); } else { ep_tx_set_response(ep, USBFS_EP_T_RES_ACK); @@ -244,7 +243,7 @@ static void update_in(uint8_t rhport, uint8_t ep, bool force) { xfer->valid = false; if (ep == 0) { ep_tx_ctrl_set(0, USBFS_EP_T_RES_NAK | (data.ep0_tog ? USBFS_EP_T_TOG : 0)); - } else if (!data.isochronous[ep]) { + } else if (!data.isochronous[ep][TUSB_DIR_IN]) { ep_tx_set_response(ep, USBFS_EP_T_RES_NAK); } dcd_event_xfer_complete(rhport, ep | TUSB_DIR_IN_MASK, xfer->processed_len, XFER_RESULT_SUCCESS, true); @@ -273,7 +272,7 @@ static void update_out(uint8_t rhport, uint8_t ep, size_t rx_len) { ep_rx_set_response(0, USBFS_EP_R_RES_NAK); } else { uint8_t rx_res = - data.isochronous[ep] ? USBFS_EP_R_RES_NYET : (xfer->valid ? USBFS_EP_R_RES_ACK : USBFS_EP_R_RES_NAK); + data.isochronous[ep][TUSB_DIR_OUT] ? USBFS_EP_R_RES_NYET : (xfer->valid ? USBFS_EP_R_RES_ACK : USBFS_EP_R_RES_NAK); ep_rx_set_response(ep, rx_res); } } @@ -338,12 +337,14 @@ void dcd_int_handler(uint8_t rhport) { // Drop an OUT packet whose data toggle doesn't match what we expect -- a host retransmit // after a lost ACK, or a host that doesn't alternate DATA0/DATA1. The hardware auto-toggle // does not reject these on its own, so the check is needed on every variant. EP0 keeps its - // own toggle via the SETUP/status flow and is exempt. - if (ep != 0 && !(int_st & USBFS_INT_ST_TOG_OK)) { break; } + // own toggle via the SETUP/status flow and is exempt; isochronous is DATA0-only (no toggle), + // so its packets must not be toggle-checked. + if (ep != 0 && !data.isochronous[ep][TUSB_DIR_OUT] && !(int_st & USBFS_INT_ST_TOG_OK)) { break; } #ifdef CH32_USBFS_EP_MANUAL_TOG // CH58x has no hardware auto-toggle: advance the expected RX toggle after each accepted packet // (EP0 included -- it also has no auto-toggle and a control-OUT data stage can span packets). - EP_CTRL(ep) ^= USBFS_EPC_R_TOG; + // Iso endpoints are DATA0-only, so leave them alone (matches the PID_IN path). + if (!data.isochronous[ep][TUSB_DIR_OUT]) { EP_CTRL(ep) ^= USBFS_EPC_R_TOG; } #endif update_out(rhport, ep, rx_len); break; @@ -352,7 +353,8 @@ void dcd_int_handler(uint8_t rhport) { case PID_IN: #ifdef CH32_USBFS_EP_MANUAL_TOG // Manual toggle: flip the TX toggle after each ACK'd IN packet (EP0 manages its own). - if (ep != 0) { EP_CTRL(ep) ^= USBFS_EPC_T_TOG; } + // Isochronous transfers are DATA0-only (no toggle), so leave iso endpoints alone. + if (ep != 0 && !data.isochronous[ep][TUSB_DIR_IN]) { EP_CTRL(ep) ^= USBFS_EPC_T_TOG; } #endif update_in(rhport, ep, false); break; @@ -462,6 +464,7 @@ bool dcd_edpt_open(uint8_t rhport, const tusb_desc_endpoint_t *desc_ep) { uint8_t dir = tu_edpt_dir(desc_ep->bEndpointAddress); TU_ASSERT(ep < EP_MAX); + data.isochronous[ep][dir] = false; // (re)opening as a non-iso endpoint clears any stale iso flag data.xfer[ep][dir].max_size = tu_edpt_packet_size(desc_ep); if (ep != 0) { @@ -483,31 +486,38 @@ void dcd_edpt_close_all(uint8_t rhport) { bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { (void)rhport; - (void)ep_addr; - (void)largest_packet_size; -#if CFG_TUSB_MCU == OPT_MCU_CH583 - // No isochronous support on CH58x: its 8-bit T_LEN caps a packet at 255B and the endpoints use - // plain 64-byte buffers, so accepting an iso max_size (up to 1023) would let update_in()/ - // update_out() run off the end of the buffer into neighbouring ones. Refuse it outright. - return false; -#else uint8_t ep = tu_edpt_number(ep_addr); uint8_t dir = tu_edpt_dir(ep_addr); + TU_ASSERT(ep < EP_MAX); + + // Endpoint buffers are 64 B, except EP3 IN which is enlarged for full-speed iso on the parts that + // support 1023-byte EP3 packets (CH32V20x/V30x/F20x; CFG_TUD_WCH_USBFS_EP3_BUFSIZE). Reject a + // larger mps rather than running off the end into the neighbouring endpoint's memory. + uint16_t max_packet = 64; +#if CFG_TUD_WCH_USBFS_EP3_BUFSIZE > 64 + if (ep == 3 && dir == TUSB_DIR_IN) { max_packet = CFG_TUD_WCH_USBFS_EP3_BUFSIZE; } +#endif + TU_VERIFY(largest_packet_size <= max_packet); - data.isochronous[ep] = true; + data.isochronous[ep][dir] = true; data.xfer[ep][dir].max_size = largest_packet_size; return true; -#endif } bool dcd_edpt_iso_activate(uint8_t rhport, const tusb_desc_endpoint_t *desc_ep) { (void)rhport; - (void)desc_ep; -#if CFG_TUSB_MCU == OPT_MCU_CH583 - return false; // CH58x has no isochronous support (see dcd_edpt_iso_alloc) -#else + const uint8_t ep = tu_edpt_number(desc_ep->bEndpointAddress); + const uint8_t dir = tu_edpt_dir(desc_ep->bEndpointAddress); + + // a transfer armed before SET_INTERFACE survives to here (no dcd close on this port): drop the + // stale descriptor and NAK the endpoint so the ISR can't complete it against the old buffer + data.xfer[ep][dir].valid = false; + if (dir == TUSB_DIR_IN) { + ep_tx_set_response(ep, USBFS_EP_T_RES_NAK); + } else { + ep_rx_set_response(ep, USBFS_EP_R_RES_NAK); + } return true; -#endif } bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t *buffer, uint16_t total_bytes, bool is_isr) { @@ -529,7 +539,7 @@ bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t *buffer, uint16_t to if (dir == TUSB_DIR_IN) { update_in(rhport, ep, true); } else { - uint8_t rx_res = data.isochronous[ep] ? USBFS_EP_R_RES_NYET : USBFS_EP_R_RES_ACK; + uint8_t rx_res = data.isochronous[ep][TUSB_DIR_OUT] ? USBFS_EP_R_RES_NYET : USBFS_EP_R_RES_ACK; ep_rx_set_response(ep, rx_res); } dcd_int_enable(rhport); @@ -565,9 +575,15 @@ void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { ep_rx_ctrl_set(0, USBFS_EP_R_RES_ACK); } } else { - // clear-stall resets the toggle to DATA0 (USB spec); manual-toggle parts then re-sync via ISR + // clear-stall resets the toggle to DATA0 (USB spec); manual-toggle parts then re-sync via ISR. + // Preserve an in-flight receive: if a read is still armed (the class driver considers it + // submitted and won't re-arm), fall back to ACK, not NAK, or the endpoint NAKs forever and the + // host times out (usbtest toggle test 29 clears the halt between bulk writes on an armed EP). if (dir == TUSB_DIR_OUT) { - ep_rx_ctrl_set(ep, EP_R_AUTO_TOG | USBFS_EP_R_RES_NAK); + uint8_t res = data.xfer[ep][TUSB_DIR_OUT].valid + ? (data.isochronous[ep][TUSB_DIR_OUT] ? USBFS_EP_R_RES_NYET : USBFS_EP_R_RES_ACK) + : USBFS_EP_R_RES_NAK; + ep_rx_ctrl_set(ep, EP_R_AUTO_TOG | res); } else { ep_tx_ctrl_set(ep, EP_T_AUTO_TOG | USBFS_EP_T_RES_NAK); } diff --git a/src/portable/wch/dcd_ch32_usbhs.c b/src/portable/wch/dcd_ch32_usbhs.c index ea3b052ad..577f86582 100644 --- a/src/portable/wch/dcd_ch32_usbhs.c +++ b/src/portable/wch/dcd_ch32_usbhs.c @@ -1,26 +1,8 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2022 Greg Davill - * Copyright (c) 2023 Denis Krasutski - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2022 Greg Davill + * SPDX-FileCopyrightText: Copyright (c) 2023 Denis Krasutski + * SPDX-FileCopyrightText: Copyright (c) 2022 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ @@ -366,8 +348,16 @@ void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { const tusb_dir_t dir = tu_edpt_dir(ep_addr); if (dir == TUSB_DIR_OUT) { - EP_RX_CTRL(ep_num) = USBHS_EP_R_RES_NAK | USBHS_EP_R_TOG_0; - ep_data_tog[ep_num][TUSB_DIR_OUT] = false; + ep_data_tog[ep_num][TUSB_DIR_OUT] = false; // clear-halt resets the toggle to DATA0 + xfer_ctl_t *xfer = XFER_CTL_BASE(ep_num, TUSB_DIR_OUT); + if (xfer->valid) { + // A receive is still armed (the class driver considers it submitted and won't re-arm it); + // re-queue it (ACK/NYET) instead of leaving it NAKing, or the endpoint NAKs forever after + // clear-halt (usbtest toggle test 29 clears the halt on an armed bulk-OUT pipe). + queue_out_packet(ep_num, xfer); + } else { + EP_RX_CTRL(ep_num) = USBHS_EP_R_RES_NAK | USBHS_EP_R_TOG_0; + } } else { EP_TX_CTRL(ep_num) = USBHS_EP_T_RES_NAK | USBHS_EP_T_TOG_0; ep_data_tog[ep_num][TUSB_DIR_IN] = false; diff --git a/src/portable/wch/hcd_ch32_usbfs.c b/src/portable/wch/hcd_ch32_usbfs.c index 7bbf122dd..5caa1bbf1 100644 --- a/src/portable/wch/hcd_ch32_usbfs.c +++ b/src/portable/wch/hcd_ch32_usbfs.c @@ -1,25 +1,7 @@ /* - * The MIT License (MIT) - * - * Copyright (c) 2024 Mitsumine Suzu (verylowfreq) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. + * SPDX-FileCopyrightText: Copyright (c) 2024 Mitsumine Suzu (verylowfreq) + * SPDX-FileCopyrightText: Copyright (c) 2024 Ha Thach (tinyusb.org) + * SPDX-License-Identifier: MIT * * This file is part of the TinyUSB stack. */ |