| Age | Commit message (Collapse) | Author |
|---|
|
Pool/config:
- record real uids (ra8m1_ek), enable usbtest for espressif s3/p4, then
park ra6m5_ek and ra8m1_ek in boards-skip (ra6m5's usbtest/MSC traffic
can kill the uPD720201 host on its ROM firmware; ra8m1 USBHS bring-up
pending); max32666/nrf54lm20 stay enabled - their MosChip flakiness
never wedges
- re-enable device/usbtest on HS boards (mimxrt1064, ch32v307) now that
uPD720201 firmware 2.0.2.6 fixes the command-ring death; mimxrt1015
stays skipped - its HS battery killed the controller on both ROM and
2.0.2.6 firmware (board-specific); match the moved host-test bundles
(f723 <-> rt1064); skip never-passing tests on the new
nrf5340dk/nrf54lm20dk boards and the detached pico host bundle, each
documented with a comment
Host-controller quirk gating in usbtest.py (auto-skip, self-heals on a
healthy xHCI):
- MosChip MCS9990 EHCI: case 25 (int-OUT never scheduled, FRINDEX bug)
and case 11 (unlinked reads complete short/EREMOTEIO)
- Renesas uPD720201 xHCI: firmware-gated. The card must run firmware
>= 2.0.2.6 (RAM-uploaded - it reverts to ROM on every power cycle):
on older firmware the command ring dies under unlink stress (a
Configure Endpoint command stops completing; the hub worker deadlocks
holding the device lock; only a host power cycle recovers; three
boards reproduced it). usbtest.py reads the FW version register (PCI
config 0x6c) and refuses to run at all on older firmware - hil_test
surfaces that as a failed test with the reason. On current firmware
the full 30-case battery runs (validated FS+HS: metro_m4, f723,
f723-DMA all 30/30).
Scheduling (hil_test.py):
- Shuffle each (board, variant)'s test order with a seeded RNG
(HIL_SHUFFLE_SEED to replay) so usbtest batteries and flash churn spread
across the timeline instead of convoying on one controller.
- Per-controller usbtest + flash semaphores: HIL_USBTEST_PARALLEL
(default 4) concurrent usbtest batteries and HIL_FLASH_PARALLEL
(default 8) concurrent flashes per host controller. Profiled on
uPD720201 firmware 2.0.2.6 across 8/1..12/8: wall time falls
22.2/14.3/12.5/10.8 min at usbtest width 1/2/3/4 and plateaus there;
zero controller errors everywhere; first battery case failures
(leaf-hub bandwidth stretch) appear at 12/8, and flash width 12 only
amplifies flasher-hub contention flakes - so 8/4 is the optimum. A
separate battery-window flash throttle was profiled and dropped.
- Give every example a unique hardcoded USB PID (0x4001-0x4022, usbtest
keeps 0x4010) instead of the PID_MAP interface bitmap: different
examples now always re-enumerate back-to-back, even on boards whose
CPU reset does not drop D+ (WCH CH58x), so the EXAMPLE_PID table and
same-PID adjacency reordering in hil_test.py are gone; only the
variant-boundary same-example repeat needs a swap.
- Report matrix: stable columns with the metric-bearing tests pinned
first (usbtest, cdc_msc_throughput, msc_file_explorer[_freertos]),
the rest alphabetical.
Fail fast:
- enum wait budget 8 s on the first attempt, 4 s on retries; dfu waits
are deadline-based so dfu-util's own runtime counts against the
budget.
A device-absent failure now costs ~3-5x a passing test (20-30 s)
instead of 10-30x (47-150 s).
- CI runs hil_test with --retry 1 and no in-run second pass: a broken
fixture fails the job fast instead of holding the self-hosted runner
for hours and blocking other PRs' HIL jobs. hil_test still writes the
.skip sidecar, so a manual re-run attempt only retests what failed.
Review fixes (multi-agent adversarial review of this commit):
- tinyusb_win_usbser.inf: the PID rework moved five CDC examples onto
even PIDs the INF's odd-only DeviceList never matched (legacy-Windows
usbser binding) - appended 0x4006/4008/400a/4020/4022 to both lists.
- usbtest example: USBTEST_TIER is now overridable and the descriptors
and pumps are tier-conditional, so a board whose DCD cannot serve a
tier lowers it instead of skipping the whole example - RA2A1 (RUSB2
with no isochronous pipe) builds at tier 3 via its BOARD_ define; the
host battery follows the tier advertised in bcdDevice. Tier-4 output
verified byte-identical after the refactor.
- dynamic_configuration's second config derived USB_PID + 11 = 0x4018,
colliding with net_lwip_webserver - now USB_PID + 0x0100, outside the
per-example space. tools/check_example_pids.py (pre-commit hook)
enforces PID uniqueness incl. derived and literal idProduct values.
- usbtest.py firmware gate: matched by device ID (uPD720201/720202,
both use the 0x6c FW register), and an unreadable version (setpci
missing/denied) now refuses with its own message instead of
masquerading as "firmware 0x00000000"; noted the gate is necessary
but not sufficient (board-specific kills stay per-board skips).
- hil_test: deadline waits use time.monotonic(); multiprocessing
context pinned to fork (raw semaphores in Pool initargs); flash and
usbtest permits unified into one fail-closed, exception-safe
ctrl_permit (unknown controller takes every slot and logs a warning
instead of silently borrowing slot 0); an all-skipped battery
reports as skip, not "0/0" failure; slow-body polls (mtp, printer,
disk read) go through a shared deadline-based wait_until so their
bodies count against the enum budget; throughput's FS detection
compares serials case-insensitively like every other walk; a missing
MSC read-speed line now fails the host msc_file_explorer test
instead of passing with an empty metric.
Hardening:
- fail fast (15 s) when a driver-registry sysfs write blocks: a wedged
device otherwise turns every subsequent battery into an unkillable
D-state writer and silently hangs the whole run
- usb-recover skill: a VM reboot is not a reliable cure (MosChip hubs
latch up across the PCIe reset); full host power cycle is
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Documentation tooling:
- Add the `build-doc` skill and `tools/build_doc.py` wrapper for local
Sphinx builds (clean / -W / open).
- Enable Markdown (MyST) in conf.py and auto-collect
examples/{device,host,dual}/*/README.md into a 3-level Examples nav
(Examples > Device/Host/Dual > example), noting each page's source
location and normalizing headings to a single H1.
- Remove the stale `.claude/commands/build-doc.md`; point the AGENTS.md
Documentation section at the skill.
Example docs:
- Add a README.md for every device/host/dual example: what it does, USB
interface table, notable tusb_config.h settings, generic CMake + Make
build steps, and how to try it.
- Fold each *_freertos variant into its base README, noting the FreeRTOS
source path and any RTOS-specific behavior.
Generated docs/examples/ output is git-ignored. Builds clean with
`sphinx-build -W`.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
The BSP family and MCU option were named "ch58x"/"CH58X", but the supported part is
the CH583/CH582 (and the SDK repo is openwch/ch583); CH585 is a separate MCU family,
so the CH58x umbrella was misleading. Rename to the specific family:
- hw/bsp/ch58x -> hw/bsp/ch583 (dir), and the BSP-local files ch58x_it.* ->
ch583_it.*, system_ch58x.* -> system_ch583.* (include guards/refs updated). The
vendor SDK files (CH58x_common.h, CH58x_*.c in hw/mcu/wch/ch583) keep their names.
- OPT_MCU_CH58X -> OPT_MCU_CH583 in tusb_option.h, tusb_mcu.h, and the shared WCH
USBFS driver (ch32_usbfs_reg.h, dcd_ch32_usbfs.c). OPT_MCU_CH582 is kept as an
alias (same value), so either name selects the same code.
- FAMILY_MCUS CH58X -> CH583, CFG_TUSB_MCU=OPT_MCU_CH583, mcu:CH58X -> mcu:CH583 in
the example skip lists, the CI build matrix (ci_set_matrix.py), the get_deps family
tag, and docs/reference/boards.rst.
Board names (ch582m_evt, yd-ch582m) are unchanged. Verified: make + cmake build for
ch582m_evt, and ci.lan HIL (all device examples pass).
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
`CFG_TUD_ENDPOINT_ONE_DIRECTION_ONLY` for improved configuration consistency across examples and core sources
|
|
|
|
|
|
fix compiling with nuc family
|
|
|
|
|
|
|
|
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
|
|
- add device/midi_test_freertos example
- update bth/dfu/midi device for cache line size
|
|
consistent
|
|
|
|
update tusb_init() to take rhport and role, defined as macro with optional argument for backward compatible
|
|
|
|
|
|
-Added support for MAX78002, MAX78002EVKIT
-Added provisions for remaining MAX32 USB parts
|
|
Initial commit for the port of TUSB to MAX32xxx parts, staring with MAX32690
- Added dcd_max32.c (based on dcd_musb.c) for interfacing with the peripheral
- Added MAX32690 part family support
- Added max32690evkit board support
- Updated examples for unique EP number requirement
- Updated get_deps.py to fetch the MSDK
Known Issues / Additional Testing Required
- msc_dual_lun only shown 1 volume on Windows
- USBTMC does not have a valid Windowsdriver
- DFU does not have a valid Windows driver
- WebUSB is "Device not Recognized"
- Need to test build scripts with IAR and Clang
|
|
|
|
Invoke unmounted state on configuration reset
|
|
|
|
|
|
|
|
|
|
add BOARD_UPPERCASE for board detection
|
|
family_configure_device/host/dual_example()
|
|
|
|
|
|
temporarily disable codespell
|
|
|
|
IAR generates warning Pe111 'statement is unreachable'. In a couple of
cases, replace return statements with TU_ATTR_FALLTHROUGH; because some
compilers apparently can't figure out that the return statements are
unreachable but do whinge about an imagined fall-through without them!
|
|
|
|
|
|
|
|
|
|
- BOARD_DEVICE/HOST_RHPORT_NUM to BOARD_TUD/H_RHPORT
- BOARD_DEVICE/HOST_RHPORT_SPEED to BOARD_TUD/H_MAX_SPEED
|
|
|
|
|
|
|
|
remove TUSB_DESC_CONFIG_ATT_REMOTE_WAKEUP attribute from non-hid
examples
|
|
|
|
|
|
- tud_dfu_dnload_complete() -> tud_dfu_download_complete()
- tud_dfu_req_dnload_data_cb() -> tud_dfu_download_cb()
- tud_dfu_req_upload_data_cb() -> tud_dfu_upload_cb()
|
|
|
|
- Examples should be CMake buildable from their own subdirectory; such a build will error out based on
matching .skip.MCU_xxx or a mismatched .only.MCU_
- It should be possible to build from a higher level and use .skip.MCU_ and .only.MCU_ to filter which
examples get built
- The intention is for the CMakeLists.txts in the examples to be non family specific and without MCU based IFs. I have
started this work, but am not really sure the state of the esp32 stuff; in any case the plan is to have
everything encapsulated in the FAMILY/family.cmake
- pico_examples now just includes examples/device/CMakeLists.txt and examples/host/CMakeLists.txt directly, as they
also build correctly when included from there.
Note that .skip.MCU_ for esp32 in the directories it wasn't previously avaiable has not been added, as the .skip is common to the regular Makefile builds also. It isn't clear whether these examples should build for esp32, but if not .skip should be added.
|
|
|
