| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Pool/config:
- record real uids (ra8m1_ek), enable usbtest for espressif s3/p4, then
park ra6m5_ek and ra8m1_ek in boards-skip (ra6m5's usbtest/MSC traffic
can kill the uPD720201 host on its ROM firmware; ra8m1 USBHS bring-up
pending); max32666/nrf54lm20 stay enabled - their MosChip flakiness
never wedges
- re-enable device/usbtest on HS boards (mimxrt1064, ch32v307) now that
uPD720201 firmware 2.0.2.6 fixes the command-ring death; mimxrt1015
stays skipped - its HS battery killed the controller on both ROM and
2.0.2.6 firmware (board-specific); match the moved host-test bundles
(f723 <-> rt1064); skip never-passing tests on the new
nrf5340dk/nrf54lm20dk boards and the detached pico host bundle, each
documented with a comment
Host-controller quirk gating in usbtest.py (auto-skip, self-heals on a
healthy xHCI):
- MosChip MCS9990 EHCI: case 25 (int-OUT never scheduled, FRINDEX bug)
and case 11 (unlinked reads complete short/EREMOTEIO)
- Renesas uPD720201 xHCI: firmware-gated. The card must run firmware
>= 2.0.2.6 (RAM-uploaded - it reverts to ROM on every power cycle):
on older firmware the command ring dies under unlink stress (a
Configure Endpoint command stops completing; the hub worker deadlocks
holding the device lock; only a host power cycle recovers; three
boards reproduced it). usbtest.py reads the FW version register (PCI
config 0x6c) and refuses to run at all on older firmware - hil_test
surfaces that as a failed test with the reason. On current firmware
the full 30-case battery runs (validated FS+HS: metro_m4, f723,
f723-DMA all 30/30).
Scheduling (hil_test.py):
- Shuffle each (board, variant)'s test order with a seeded RNG
(HIL_SHUFFLE_SEED to replay) so usbtest batteries and flash churn spread
across the timeline instead of convoying on one controller.
- Per-controller usbtest + flash semaphores: HIL_USBTEST_PARALLEL
(default 4) concurrent usbtest batteries and HIL_FLASH_PARALLEL
(default 8) concurrent flashes per host controller. Profiled on
uPD720201 firmware 2.0.2.6 across 8/1..12/8: wall time falls
22.2/14.3/12.5/10.8 min at usbtest width 1/2/3/4 and plateaus there;
zero controller errors everywhere; first battery case failures
(leaf-hub bandwidth stretch) appear at 12/8, and flash width 12 only
amplifies flasher-hub contention flakes - so 8/4 is the optimum. A
separate battery-window flash throttle was profiled and dropped.
- Give every example a unique hardcoded USB PID (0x4001-0x4022, usbtest
keeps 0x4010) instead of the PID_MAP interface bitmap: different
examples now always re-enumerate back-to-back, even on boards whose
CPU reset does not drop D+ (WCH CH58x), so the EXAMPLE_PID table and
same-PID adjacency reordering in hil_test.py are gone; only the
variant-boundary same-example repeat needs a swap.
- Report matrix: stable columns with the metric-bearing tests pinned
first (usbtest, cdc_msc_throughput, msc_file_explorer[_freertos]),
the rest alphabetical.
Fail fast:
- enum wait budget 8 s on the first attempt, 4 s on retries; dfu waits
are deadline-based so dfu-util's own runtime counts against the
budget.
A device-absent failure now costs ~3-5x a passing test (20-30 s)
instead of 10-30x (47-150 s).
- CI runs hil_test with --retry 1 and no in-run second pass: a broken
fixture fails the job fast instead of holding the self-hosted runner
for hours and blocking other PRs' HIL jobs. hil_test still writes the
.skip sidecar, so a manual re-run attempt only retests what failed.
Review fixes (multi-agent adversarial review of this commit):
- tinyusb_win_usbser.inf: the PID rework moved five CDC examples onto
even PIDs the INF's odd-only DeviceList never matched (legacy-Windows
usbser binding) - appended 0x4006/4008/400a/4020/4022 to both lists.
- usbtest example: USBTEST_TIER is now overridable and the descriptors
and pumps are tier-conditional, so a board whose DCD cannot serve a
tier lowers it instead of skipping the whole example - RA2A1 (RUSB2
with no isochronous pipe) builds at tier 3 via its BOARD_ define; the
host battery follows the tier advertised in bcdDevice. Tier-4 output
verified byte-identical after the refactor.
- dynamic_configuration's second config derived USB_PID + 11 = 0x4018,
colliding with net_lwip_webserver - now USB_PID + 0x0100, outside the
per-example space. tools/check_example_pids.py (pre-commit hook)
enforces PID uniqueness incl. derived and literal idProduct values.
- usbtest.py firmware gate: matched by device ID (uPD720201/720202,
both use the 0x6c FW register), and an unreadable version (setpci
missing/denied) now refuses with its own message instead of
masquerading as "firmware 0x00000000"; noted the gate is necessary
but not sufficient (board-specific kills stay per-board skips).
- hil_test: deadline waits use time.monotonic(); multiprocessing
context pinned to fork (raw semaphores in Pool initargs); flash and
usbtest permits unified into one fail-closed, exception-safe
ctrl_permit (unknown controller takes every slot and logs a warning
instead of silently borrowing slot 0); an all-skipped battery
reports as skip, not "0/0" failure; slow-body polls (mtp, printer,
disk read) go through a shared deadline-based wait_until so their
bodies count against the enum budget; throughput's FS detection
compares serials case-insensitively like every other walk; a missing
MSC read-speed line now fails the host msc_file_explorer test
instead of passing with an empty metric.
Hardening:
- fail fast (15 s) when a driver-registry sysfs write blocks: a wedged
device otherwise turns every subsequent battery into an unkillable
D-state writer and silently hangs the whole run
- usb-recover skill: a VM reboot is not a reliable cure (MosChip hubs
latch up across the PCIe reset); full host power cycle is
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Documentation tooling:
- Add the `build-doc` skill and `tools/build_doc.py` wrapper for local
Sphinx builds (clean / -W / open).
- Enable Markdown (MyST) in conf.py and auto-collect
examples/{device,host,dual}/*/README.md into a 3-level Examples nav
(Examples > Device/Host/Dual > example), noting each page's source
location and normalizing headings to a single H1.
- Remove the stale `.claude/commands/build-doc.md`; point the AGENTS.md
Documentation section at the skill.
Example docs:
- Add a README.md for every device/host/dual example: what it does, USB
interface table, notable tusb_config.h settings, generic CMake + Make
build steps, and how to try it.
- Fold each *_freertos variant into its base README, noting the FreeRTOS
source path and any RTOS-specific behavior.
Generated docs/examples/ output is git-ignored. Builds clean with
`sphinx-build -W`.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
|
|
The BSP family and MCU option were named "ch58x"/"CH58X", but the supported part is
the CH583/CH582 (and the SDK repo is openwch/ch583); CH585 is a separate MCU family,
so the CH58x umbrella was misleading. Rename to the specific family:
- hw/bsp/ch58x -> hw/bsp/ch583 (dir), and the BSP-local files ch58x_it.* ->
ch583_it.*, system_ch58x.* -> system_ch583.* (include guards/refs updated). The
vendor SDK files (CH58x_common.h, CH58x_*.c in hw/mcu/wch/ch583) keep their names.
- OPT_MCU_CH58X -> OPT_MCU_CH583 in tusb_option.h, tusb_mcu.h, and the shared WCH
USBFS driver (ch32_usbfs_reg.h, dcd_ch32_usbfs.c). OPT_MCU_CH582 is kept as an
alias (same value), so either name selects the same code.
- FAMILY_MCUS CH58X -> CH583, CFG_TUSB_MCU=OPT_MCU_CH583, mcu:CH58X -> mcu:CH583 in
the example skip lists, the CI build matrix (ci_set_matrix.py), the get_deps family
tag, and docs/reference/boards.rst.
Board names (ch582m_evt, yd-ch582m) are unchanged. Verified: make + cmake build for
ch582m_evt, and ci.lan HIL (all device examples pass).
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
CH58x has no isochronous support (dcd_edpt_iso_alloc() returns false), but the
audio class ignores that result and the endpoints fall back to capped 64-byte
non-iso transfers, producing non-functional audio firmware. video_capture and the
FreeRTOS audio examples already carry mcu:CH58X; add it to the remaining iso
examples (audio_test, audio_4_channel_mic, audio_test_multi_rate, cdc_uac2,
uac2_headset, uac2_speaker_fb) so they are not built for CH58x.
Found by Codex review. Verified via build_utils.skip_example() that all six now
skip on ch582m_evt while control examples (e.g. cdc_msc) still build.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
The audio20 get/set entity dispatchers already extract entity_id from
wIndex and route to the matching clock / feature-unit helper, so each
helper's own entity_id re-derivation and TU_ASSERT(entity_id == ...) was
dead: the helper is only ever reached for its one entity. Unknown
entities are still rejected by the dispatcher's "not handled" path.
Remove the redundant local, the dead assert, and the constant "entity"
field from each helper's not-supported log (the message text already
identifies the entity). The local is dropped entirely rather than kept
for the log, since TU_LOG1 compiles out in release and would leave it
unused.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
Co-authored-by: HiFiPhile <[email protected]>
|
|
(4KB FIFO)
|
|
extraction
- Add TU_BITFIELD_ORDER guards for audio10_desc_as_iso_data_ep_t.bmAttributes in audio.h
- Add TU_BITFIELD_ORDER guards for audio20_control_request_t.bmRequestType_bit in audio.h
- Fix cdc_uac2/src/uac2_app.c: replace alias cast with TU_U16_LOW/HIGH field extraction
- Fix uac2_headset/src/main.c: replace alias cast with TU_U16_LOW/HIGH field extraction
- Fix uac2_speaker_fb/src/main.c: replace alias cast with TU_U16_LOW/HIGH field extraction
Addresses review comment: https://github.com/hathach/tinyusb/pull/3597#issuecomment-4320042007
Agent-Logs-Url: https://github.com/hathach/tinyusb/sessions/8b695271-74b3-4a26-b3d8-c48ecdf2e481
Co-authored-by: HiFiPhile <[email protected]>
|
|
# Conflicts:
# src/common/tusb_types.h
# src/portable/mentor/musb/dcd_musb.c
|
|
`CFG_TUD_ENDPOINT_ONE_DIRECTION_ONLY` for improved configuration consistency across examples and core sources
|
|
|
|
|
|
|
|
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
fix compiling with nuc family
|
|
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
|
|
|
|
|
|
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: Mengsk <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: Mengsk <[email protected]>
|
|
Signed-off-by: Mengsk <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
driver can execute xfer_is()
|
|
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
consistent
|
|
|
|
update tusb_init() to take rhport and role, defined as macro with optional argument for backward compatible
|
|
|
|
|
|
|
|
-Added support for MAX78002, MAX78002EVKIT
-Added provisions for remaining MAX32 USB parts
|
|
Initial commit for the port of TUSB to MAX32xxx parts, staring with MAX32690
- Added dcd_max32.c (based on dcd_musb.c) for interfacing with the peripheral
- Added MAX32690 part family support
- Added max32690evkit board support
- Updated examples for unique EP number requirement
- Updated get_deps.py to fetch the MSDK
Known Issues / Additional Testing Required
- msc_dual_lun only shown 1 volume on Windows
- USBTMC does not have a valid Windowsdriver
- DFU does not have a valid Windows driver
- WebUSB is "Device not Recognized"
- Need to test build scripts with IAR and Clang
|
|
|
|
|
