Merge tag 'i2c-updates-for-2026.07-rc3' of https://source.denx.de/u-boot/custodians/u-boot-i2c

updates for 2026.07-rc3

- designware_i2c: Staticize driver ops from Marek
- i2c: Remove legacy CONFIG_SYS_I2C_SOFT
-

1 files changed, 0 insertions, 92 deletions

diff --git a/README b/README
index 6836a917c79..f0bad144360 100644
--- a/README
+++ b/README
@@ -628,98 +628,6 @@ The following options need to be configured:
 
 		If you do not have i2c muxes on your board, omit this define.
 
-- Legacy I2C Support:
-		If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
-		then the following macros need to be defined (examples are
-		from include/configs/lwmon.h):
-
-		I2C_INIT
-
-		(Optional). Any commands necessary to enable the I2C
-		controller or configure ports.
-
-		eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |=	PB_SCL)
-
-		I2C_ACTIVE
-
-		The code necessary to make the I2C data line active
-		(driven).  If the data line is open collector, this
-		define can be null.
-
-		eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |=  PB_SDA)
-
-		I2C_TRISTATE
-
-		The code necessary to make the I2C data line tri-stated
-		(inactive).  If the data line is open collector, this
-		define can be null.
-
-		eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
-
-		I2C_READ
-
-		Code that returns true if the I2C data line is high,
-		false if it is low.
-
-		eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-
-		I2C_SDA(bit)
-
-		If <bit> is true, sets the I2C data line high. If it
-		is false, it clears it (low).
-
-		eg: #define I2C_SDA(bit) \
-			if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SDA
-
-		I2C_SCL(bit)
-
-		If <bit> is true, sets the I2C clock line high. If it
-		is false, it clears it (low).
-
-		eg: #define I2C_SCL(bit) \
-			if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
-
-		I2C_DELAY
-
-		This delay is invoked four times per clock cycle so this
-		controls the rate of data transfer.  The data rate thus
-		is 1 / (I2C_DELAY * 4). Often defined to be something
-		like:
-
-		#define I2C_DELAY  udelay(2)
-
-		CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
-
-		If your arch supports the generic GPIO framework (asm/gpio.h),
-		then you may alternatively define the two GPIOs that are to be
-		used as SCL / SDA.  Any of the previous I2C_xxx macros will
-		have GPIO-based defaults assigned to them as appropriate.
-
-		You should define these to the GPIO value as given directly to
-		the generic GPIO functions.
-
-		CFG_SYS_I2C_NOPROBES
-
-		This option specifies a list of I2C devices that will be skipped
-		when the 'i2c probe' command is issued.
-
-		e.g.
-			#define CFG_SYS_I2C_NOPROBES {0x50,0x68}
-
-		will skip addresses 0x50 and 0x68 on a board with one I2C bus
-
-		CONFIG_SOFT_I2C_READ_REPEATED_START
-
-		defining this will force the i2c_read() function in
-		the soft_i2c driver to perform an I2C repeated start
-		between writing the address pointer and reading the
-		data.  If this define is omitted the default behaviour
-		of doing a stop-start sequence will be used.  Most I2C
-		devices can use either method, but some require one or
-		the other.
-
 - SPI Support:	CONFIG_SPI
 
 		Enables SPI driver (so far only tested with