doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Prafulla Wadaskar <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Kim Phillips <[email protected]>
Cc: Andy Fleming <[email protected]>
Cc: Jason Jin <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Daniel Schwierzeck <[email protected]>
Acked-by: Stefano Babic <[email protected]>
Acked-by: Daniel Schwierzeck <[email protected]>

1 files changed, 0 insertions, 67 deletions

diff --git a/doc/README.dnp5370 b/doc/README.dnp5370
deleted file mode 100644
index 0172698e96d..00000000000
--- a/doc/README.dnp5370
+++ /dev/null
@@ -1,67 +0,0 @@
-This document describes the board support for
-Dil/NetPC DNP/5370 (http://www.dilnetpc.com/dnp0086.htm) module.
-The distributor is SSV (http://www.ssv-embedded.de),
-
-The module used to develop the support files contains:
-
-*   Processor: Blackfin BF537 Rev 0.3 (600 MHz core / 120MHz RAM)
-
-*   RAM: 32 MB SDRAM
-    Hynix HY57V561620FTP-H 810EA
-    Connected to Blackfin via "Expansion Bus"
-    Address range 0x0000.0000 - 0x1fff.ffff
-
-*   NOR flash: 32 MBit (4 MByte)
-    Exel Semiconductor ES29LVS320EB
-    Connected to Blackfin via "Expansion Bus",
-    Chip Selects 0, 1 and 2, each is connected
-    to a 1 MB memory bank at Blackfin, therefore
-    only 3 MB accessible.
-    Address range 0x2000.0000 - 0x202f.ffff
-    CFI compatible
-
-    Exel Semiconductor was bought by Rohm Semiconductor (www.rohm.com).
-
-*   NAND flash: 64 MBit (8 MByte)
-    Atmel 45DB642D-CNU
-    Connected to Blackfin via SPI
-    CFI compatible
-
-*   Davicom DM9161EP Ethernet PHY
-
-*   A SD card reader, connected via SPI
-
-*   Hardware watchdog MAX823 or TPS3823
-
-(other devices not listed here)
-
-To run it, the module must be inserted in a 64 pin DIL socket
-on another board, e.g. DNP/EVA13 (together: SSV SK28).
-
-The Blackfin is booted from NOR flash. The NOR flash data begins
-with the U-Boot code and is then followed by the Linux code.
-Finally, the MAC is stored in the last sector.
-You may need to adjust these settings to your needs.
-The memory map used to develop the board support is:
-
-Memory map:
-0x00000000 .. 0x01ffffff SDRAM
-0x20000000 .. 0x202fffff NOR flash
-
-RAM use:
-0x01f9bffc .. 0x01fbbffb U-Boot stack
-0x01f9c000 .. 0x01f9ffff U-Boot global data
-0x01fa0000 .. 0x01fbffff U-Boot malloc() RAM
-0x01fc0000 .. 0x01ffffff U-Boot execution RAM
-
-NOR flash use:
-0x20000000 .. 0x0002ffff U-Boot
-0x20004000 .. 0x20005fff U-Boot environment
-0x20030000 .. 0x202effff Linux kernel image
-0x202f0000 .. 0x202fffff MAC address sector
-
-NOR flash is 0x00300000 (3145728) bytes large (3 MB).
-Max space for compressed kernel in flash is 0x002c0000 (2883584) bytes (2.75 MB)
-Max space for u-boot in flash is 0x00030000 (196608) bytes (192 KB)
-
-The module is hardwired to BYPASS boot mode.