drivers: Use CONFIG_XPL_BUILD instead of CONFIG_SPL_BUILD

Use the new symbol to refer to any 'SPL' build, including TPL and VPL

Signed-off-by: Simon Glass <[email protected]>

7 files changed, 8 insertions, 8 deletions

diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 78810f98367..66bd30b837b 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -63,7 +63,7 @@ obj-$(CONFIG_XEN_SERIAL) += serial_xen.o
 obj-$(CONFIG_XTENSA_SEMIHOSTING_SERIAL) += serial_xtensa_semihosting.o
 obj-$(CONFIG_S5P4418_PL011_SERIAL) += serial_s5p4418_pl011.o
 
-ifndef CONFIG_SPL_BUILD
+ifndef CONFIG_XPL_BUILD
 obj-$(CONFIG_USB_TTY) += usbtty.o
 endif
 obj-$(CONFIG_UART4_SERIAL) += serial_adi_uart4.o
diff --git a/drivers/serial/atmel_usart.c b/drivers/serial/atmel_usart.c
index 7e45a80969e..0b35582aaa4 100644
--- a/drivers/serial/atmel_usart.c
+++ b/drivers/serial/atmel_usart.c
@@ -218,7 +218,7 @@ static const struct dm_serial_ops atmel_serial_ops = {
 	.setbrg = atmel_serial_setbrg,
 };
 
-#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_SPL_CLK)
+#if defined(CONFIG_XPL_BUILD) && !defined(CONFIG_SPL_CLK)
 static int atmel_serial_enable_clk(struct udevice *dev)
 {
 	struct atmel_serial_priv *priv = dev_get_priv(dev);
diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c
index 55bc39648d7..3489228127e 100644
--- a/drivers/serial/ns16550.c
+++ b/drivers/serial/ns16550.c
@@ -227,7 +227,7 @@ static void ns16550_setbrg(struct ns16550 *com_port, int baud_divisor)
 
 void ns16550_init(struct ns16550 *com_port, int baud_divisor)
 {
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_OMAP34XX)
+#if defined(CONFIG_XPL_BUILD) && defined(CONFIG_OMAP34XX)
 	/*
 	 * On some OMAP3/OMAP4 devices when UART3 is configured for boot mode
 	 * before SPL starts only THRE bit is set. We have to empty the
@@ -303,7 +303,7 @@ void ns16550_putc(struct ns16550 *com_port, char c)
 char ns16550_getc(struct ns16550 *com_port)
 {
 	while ((serial_in(&com_port->lsr) & UART_LSR_DR) == 0) {
-#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_USB_TTY)
+#if !defined(CONFIG_XPL_BUILD) && defined(CONFIG_USB_TTY)
 		extern void usbtty_poll(void);
 		usbtty_poll();
 #endif
diff --git a/drivers/serial/serial-uclass.c b/drivers/serial/serial-uclass.c
index 84f02f7ac76..9feaa1eceec 100644
--- a/drivers/serial/serial-uclass.c
+++ b/drivers/serial/serial-uclass.c
@@ -101,7 +101,7 @@ static void serial_find_console_or_panic(void)
 			}
 		}
 	}
-	if (!IS_ENABLED(CONFIG_SPL_BUILD) || !CONFIG_IS_ENABLED(OF_CONTROL) ||
+	if (!IS_ENABLED(CONFIG_XPL_BUILD) || !CONFIG_IS_ENABLED(OF_CONTROL) ||
 	    !blob) {
 		/*
 		 * Try to use CONFIG_CONS_INDEX if available (it is numbered
diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c
index dc4bb06fa99..e10ca6eef76 100644
--- a/drivers/serial/serial.c
+++ b/drivers/serial/serial.c
@@ -315,7 +315,7 @@ static struct serial_device *get_current(void)
 
 	/* We must have a console device */
 	if (!dev) {
-#ifdef CONFIG_SPL_BUILD
+#ifdef CONFIG_XPL_BUILD
 		puts("Cannot find console\n");
 		hang();
 #else
diff --git a/drivers/serial/serial_s5p.c b/drivers/serial/serial_s5p.c
index 801b7645afa..734780a124a 100644
--- a/drivers/serial/serial_s5p.c
+++ b/drivers/serial/serial_s5p.c
@@ -117,7 +117,7 @@ static void __maybe_unused s5p_serial_baud(struct s5p_uart *uart, u8 reg_width,
 		writeb(val % 16, &uart->rest.value);
 }
 
-#ifndef CONFIG_SPL_BUILD
+#ifndef CONFIG_XPL_BUILD
 int s5p_serial_setbrg(struct udevice *dev, int baudrate)
 {
 	struct s5p_serial_plat *plat = dev_get_plat(dev);
diff --git a/drivers/serial/serial_zynq.c b/drivers/serial/serial_zynq.c
index 55f13c00ddf..b74712f3eeb 100644
--- a/drivers/serial/serial_zynq.c
+++ b/drivers/serial/serial_zynq.c
@@ -152,7 +152,7 @@ static int zynq_serial_setbrg(struct udevice *dev, int baudrate)
 	return 0;
 }
 
-#if !defined(CONFIG_SPL_BUILD)
+#if !defined(CONFIG_XPL_BUILD)
 static int zynq_serial_setconfig(struct udevice *dev, uint serial_config)
 {
 	struct zynq_uart_plat *plat = dev_get_plat(dev);