Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2021.01

arm64:
- Support for bigger U-Boot images compiled with PIE

microblaze:
- Extend support for LE/BE systems

zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode

zynqmp-r5:
- Fix MPU mapping and defconfig setting.

xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot

cmd:
- pxe: Add fixing for platforms with manual relocation support

clk:
- fixed_rate: Add DM flag to support early boot on r5

fpga:
- zynqmppl: Use only firmware interface and enable SPL build

serial:
- uartlite: Enable for ARM systems and support endians

mmc:
- zynq: Fix indentation

net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64

kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values

bindings:
- Add binding doc for vsc8531

2 files changed, 48 insertions, 16 deletions

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index e344677f91f..b4805a2e4ea 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -734,7 +734,7 @@ config UNIPHIER_SERIAL
 
 config XILINX_UARTLITE
 	bool "Xilinx Uarlite support"
-	depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || 4xx)
+	depends on DM_SERIAL
 	help
 	  If you have a Xilinx based board and want to use the uartlite
 	  serial ports, say Y to this option. If unsure, say N.
@@ -802,7 +802,7 @@ config STM32_SERIAL
 
 config ZYNQ_SERIAL
 	bool "Cadence (Xilinx Zynq) UART support"
-	depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_ZYNQMP_R5)
+	depends on DM_SERIAL
 	help
 	  This driver supports the Cadence UART. It is found e.g. in Xilinx
 	  Zynq/ZynqMP.
diff --git a/drivers/serial/serial_xuartlite.c b/drivers/serial/serial_xuartlite.c
index 5116d13751d..236ab860ad8 100644
--- a/drivers/serial/serial_xuartlite.c
+++ b/drivers/serial/serial_xuartlite.c
@@ -23,6 +23,8 @@
 #define ULITE_CONTROL_RST_TX	0x01
 #define ULITE_CONTROL_RST_RX	0x02
 
+static bool little_endian;
+
 struct uartlite {
 	unsigned int rx_fifo;
 	unsigned int tx_fifo;
@@ -34,15 +36,31 @@ struct uartlite_platdata {
 	struct uartlite *regs;
 };
 
+static u32 uart_in32(void __iomem *addr)
+{
+	if (little_endian)
+		return in_le32(addr);
+	else
+		return in_be32(addr);
+}
+
+static void uart_out32(void __iomem *addr, u32 val)
+{
+	if (little_endian)
+		out_le32(addr, val);
+	else
+		out_be32(addr, val);
+}
+
 static int uartlite_serial_putc(struct udevice *dev, const char ch)
 {
 	struct uartlite_platdata *plat = dev_get_platdata(dev);
 	struct uartlite *regs = plat->regs;
 
-	if (in_be32(&regs->status) & SR_TX_FIFO_FULL)
+	if (uart_in32(&regs->status) & SR_TX_FIFO_FULL)
 		return -EAGAIN;
 
-	out_be32(&regs->tx_fifo, ch & 0xff);
+	uart_out32(&regs->tx_fifo, ch & 0xff);
 
 	return 0;
 }
@@ -52,10 +70,10 @@ static int uartlite_serial_getc(struct udevice *dev)
 	struct uartlite_platdata *plat = dev_get_platdata(dev);
 	struct uartlite *regs = plat->regs;
 
-	if (!(in_be32(&regs->status) & SR_RX_FIFO_VALID_DATA))
+	if (!(uart_in32(&regs->status) & SR_RX_FIFO_VALID_DATA))
 		return -EAGAIN;
 
-	return in_be32(&regs->rx_fifo) & 0xff;
+	return uart_in32(&regs->rx_fifo) & 0xff;
 }
 
 static int uartlite_serial_pending(struct udevice *dev, bool input)
@@ -64,19 +82,26 @@ static int uartlite_serial_pending(struct udevice *dev, bool input)
 	struct uartlite *regs = plat->regs;
 
 	if (input)
-		return in_be32(&regs->status) & SR_RX_FIFO_VALID_DATA;
+		return uart_in32(&regs->status) & SR_RX_FIFO_VALID_DATA;
 
-	return !(in_be32(&regs->status) & SR_TX_FIFO_EMPTY);
+	return !(uart_in32(&regs->status) & SR_TX_FIFO_EMPTY);
 }
 
 static int uartlite_serial_probe(struct udevice *dev)
 {
 	struct uartlite_platdata *plat = dev_get_platdata(dev);
 	struct uartlite *regs = plat->regs;
+	int ret;
 
-	out_be32(&regs->control, 0);
-	out_be32(&regs->control, ULITE_CONTROL_RST_RX | ULITE_CONTROL_RST_TX);
-	in_be32(&regs->control);
+	uart_out32(&regs->control, 0);
+	uart_out32(&regs->control, ULITE_CONTROL_RST_RX | ULITE_CONTROL_RST_TX);
+	ret = uart_in32(&regs->status);
+	/* Endianness detection */
+	if ((ret & SR_TX_FIFO_EMPTY) != SR_TX_FIFO_EMPTY) {
+		little_endian = true;
+		uart_out32(&regs->control, ULITE_CONTROL_RST_RX |
+			   ULITE_CONTROL_RST_TX);
+	}
 
 	return 0;
 }
@@ -119,20 +144,27 @@ U_BOOT_DRIVER(serial_uartlite) = {
 static inline void _debug_uart_init(void)
 {
 	struct uartlite *regs = (struct uartlite *)CONFIG_DEBUG_UART_BASE;
+	int ret;
 
-	out_be32(&regs->control, 0);
-	out_be32(&regs->control, ULITE_CONTROL_RST_RX | ULITE_CONTROL_RST_TX);
-	in_be32(&regs->control);
+	uart_out32(&regs->control, 0);
+	uart_out32(&regs->control, ULITE_CONTROL_RST_RX | ULITE_CONTROL_RST_TX);
+	uart_in32(&regs->status);
+	/* Endianness detection */
+	if ((ret & SR_TX_FIFO_EMPTY) != SR_TX_FIFO_EMPTY) {
+		little_endian = true;
+		uart_out32(&regs->control, ULITE_CONTROL_RST_RX |
+			   ULITE_CONTROL_RST_TX);
+	}
 }
 
 static inline void _debug_uart_putc(int ch)
 {
 	struct uartlite *regs = (struct uartlite *)CONFIG_DEBUG_UART_BASE;
 
-	while (in_be32(&regs->status) & SR_TX_FIFO_FULL)
+	while (uart_in32(&regs->status) & SR_TX_FIFO_FULL)
 		;
 
-	out_be32(&regs->tx_fifo, ch & 0xff);
+	uart_out32(&regs->tx_fifo, ch & 0xff);
 }
 
 DEBUG_UART_FUNCS