Merge branch 'next'

Bring in the assorted changes that have been staged in the 'next' branch
prior to release.

Signed-off-by: Tom Rini <[email protected]>

13 files changed, 94 insertions, 515 deletions

diff --git a/include/configs/P1023RDB.h b/include/configs/P1023RDB.h
deleted file mode 100644
index 5c29a4f274e..00000000000
--- a/include/configs/P1023RDB.h
+++ /dev/null
@@ -1,338 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2013 Freescale Semiconductor, Inc.
- *
- * Authors:  Roy Zang <[email protected]>
- *	     Chunhe Lan <[email protected]>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <linux/stringify.h>
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
-#endif
-
-/* High Level Configuration Options */
-
-#define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
-#define CONFIG_PCIE1		/* PCIE controller 1 (slot 1) */
-#define CONFIG_PCIE2		/* PCIE controller 2 (slot 2) */
-#define CONFIG_PCIE3		/* PCIE controller 3 (slot 3) */
-#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
-#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_clock_freq(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ	66666666
-#define CONFIG_DDR_CLK_FREQ	CONFIG_SYS_CLK_FREQ
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE			/* toggle L2 cache */
-#define CONFIG_BTB			/* toggle branch predition */
-#define CONFIG_HWCONFIG
-
-#define CONFIG_ENABLE_36BIT_PHYS
-
-/* Implement conversion of addresses in the LBC */
-#define CONFIG_SYS_LBC_LBCR		0x00000000
-#define CONFIG_SYS_LBC_LCRR		LCRR_CLKDIV_8
-
-/* DDR Setup */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	1
-
-#define CONFIG_DDR_SPD
-#define CONFIG_SYS_SDRAM_SIZE		512u	/* DDR is 512M */
-#define CONFIG_SYS_SPD_BUS_NUM          0
-#define SPD_EEPROM_ADDRESS              0x50
-#define CONFIG_SYS_DDR_RAW_TIMING
-
-/*
- * Memory map
- *
- * 0x0000_0000	0x1fff_ffff	DDR			512M cacheable
- * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
- * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
- * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
- * 0xff00_0000	0xff3f_ffff	DPAA_QBMAN		4M cacheable
- * 0xff60_0000	0xff7f_ffff	CCSR			2M non-cacheable
- * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K cacheable TLB0
- *
- * Localbus non-cacheable
- *
- * 0xec00_0000	0xefff_ffff	NOR flash		64M non-cacheable
- * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_FLASH_BASE		0xec000000 /* start of FLASH 64M */
-#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_FLASH_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
-				| BR_PS_16 | BR_V)
-#define CONFIG_FLASH_OR_PRELIM	0xfc000ff7
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	512	/* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000/* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN	(768 * 1024)	  /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN	(6 * 1024 * 1024) /* Reserved for malloc */
-
-#define CONFIG_SYS_NAND_BASE		0xffa00000
-#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
-
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
-
-/* NAND flash config */
-#define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
-				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
-				| BR_PS_8		/* Port Size = 8bit */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_NAND_OR_PRELIM  (OR_AM_256KB		/* length 256K */ \
-				| OR_FCM_PGS \
-				| OR_FCM_CSCT \
-				| OR_FCM_CST \
-				| OR_FCM_CHT \
-				| OR_FCM_SCY_1 \
-				| OR_FCM_TRLX \
-				| OR_FCM_EHTR)
-
-#define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
-#define CONFIG_SYS_OR0_PRELIM	CONFIG_FLASH_OR_PRELIM	/* NOR Options */
-#define CONFIG_SYS_BR1_PRELIM	CONFIG_SYS_NAND_BR_PRELIM
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-
-/* Serial Port */
-#undef	CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR + 0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_ID_EEPROM
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_BUS_NUM		0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 3, Slot 1, tgtid 3, Base address b000 */
-#define CONFIG_SYS_PCIE3_NAME		"Slot 3"
-#define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
-#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS	0xffc00000
-#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 2, direct to uli, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME		"Slot 2"
-#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
-#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 1, Slot 2, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME		"Slot 1"
-#define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
-#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc20000
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
-
-#if defined(CONFIG_PCI)
-#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#endif	/* CONFIG_PCI */
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO		/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
-
-/*
- * USB
- */
-#define CONFIG_HAS_FSL_DR_USB
-#ifdef CONFIG_HAS_FSL_DR_USB
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
-#endif
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)   /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)   /* Increase max gunzip size */
-
-/*
- * Environment Configuration
- */
-#define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_UBOOTPATH	(u-boot.bin) /* U-Boot image on TFTP server */
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR		1000000
-
-/* Qman/Bman */
-#define CONFIG_SYS_QMAN_MEM_BASE	0xff000000
-#define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
-#define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
-#define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
-#define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
-					CONFIG_SYS_QMAN_CENA_SIZE)
-#define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_SWP_ISDR_REG	0xE08
-#define CONFIG_SYS_BMAN_MEM_BASE	0xff200000
-#define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
-#define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
-#define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
-#define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
-					CONFIG_SYS_BMAN_CENA_SIZE)
-#define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_SWP_ISDR_REG	0xE08
-
-/* For FM */
-#define CONFIG_SYS_DPAA_FMAN
-
-/* Default address of microcode for the Linux Fman driver */
-/* QE microcode/firmware address */
-#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
-#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR	0x1
-#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR	0x2
-
-#define CONFIG_SYS_TBIPA_VALUE	8
-#define CONFIG_ETHPRIME		"FM1@DTSEC1"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS	\
-	"netdev=eth0\0"						\
-	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
-	"loadaddr=1000000\0"					\
-	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
-	"tftpflash=tftpboot $loadaddr $uboot; "			\
-		"protect off $ubootaddr +$filesize; "		\
-		"erase $ubootaddr +$filesize; "			\
-		"cp.b $loadaddr $ubootaddr $filesize; "		\
-		"protect on $ubootaddr +$filesize; "		\
-		"cmp.b $loadaddr $ubootaddr $filesize\0"	\
-	"consoledev=ttyS0\0"					\
-	"ramdiskaddr=2000000\0"					\
-	"ramdiskfile=rootfs.ext2.gz.uboot\0"			\
-	"fdtaddr=1e00000\0"					\
-	"fdtfile=p1023rdb.dtb\0"				\
-	"othbootargs=ramdisk_size=600000\0"			\
-	"bdev=sda1\0"						\
-	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
-
-#define CONFIG_HDBOOT					\
-	"setenv bootargs root=/dev/$bdev rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND						\
-	"setenv bootargs root=/dev/nfs rw "				\
-	"nfsroot=$serverip:$rootpath "					\
-	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-	"console=$consoledev,$baudrate $othbootargs;"			\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND						\
-	"setenv bootargs root=/dev/ram rw "				\
-	"console=$consoledev,$baudrate $othbootargs;"			\
-	"tftp $ramdiskaddr $ramdiskfile;"				\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND		CONFIG_RAMBOOTCOMMAND
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/P5020DS.h b/include/configs/P5020DS.h
deleted file mode 100644
index 873d39a10c5..00000000000
--- a/include/configs/P5020DS.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2009-2011 Freescale Semiconductor, Inc.
- */
-
-/*
- * P5020 DS board configuration file
- * Also supports P5010 DS
- */
-#define CONFIG_FSL_NGPIXIS		/* use common ngPIXIS code */
-
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_FSL_SATA_V2
-#define CONFIG_PCIE3
-#define CONFIG_PCIE4
-#define CONFIG_SYS_FSL_RAID_ENGINE
-#define CONFIG_SYS_DPAA_RMAN
-
-#define CONFIG_SYS_SRIO
-#define CONFIG_SRIO1			/* SRIO port 1 */
-#define CONFIG_SRIO2			/* SRIO port 2 */
-#define CONFIG_SRIO_PCIE_BOOT_MASTER
-#define CONFIG_ICS307_REFCLK_HZ		25000000  /* ICS307 ref clk freq */
-
-#include "corenet_ds.h"
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 9c4ef369c5c..5af90d932d5 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -66,6 +66,12 @@
 #define BOOTENV_DEV_NAME_NAND(devtypeu, devtypel, instance) \
 	#devtypel #instance " "
 
+#if CONFIG_IS_ENABLED(CMD_USB)
+# define BOOT_TARGET_USB(func) func(USB, usb, 0)
+#else
+# define BOOT_TARGET_USB(func)
+#endif
+
 #if CONFIG_IS_ENABLED(CMD_PXE)
 # define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
 #else
@@ -84,6 +90,7 @@
 	func(MMC, mmc, 1) \
 	func(LEGACY_MMC, legacy_mmc, 1) \
 	func(NAND, nand, 0) \
+	BOOT_TARGET_USB(func) \
 	BOOT_TARGET_PXE(func) \
 	BOOT_TARGET_DHCP(func)
 
@@ -280,8 +287,6 @@
 #define CONFIG_SYS_ENV_SECT_SIZE	CONFIG_SYS_NAND_BLOCK_SIZE
 #endif
 
-/* SPI flash. */
-
 /* Network. */
 /* Enable Atheros phy driver */
 
diff --git a/include/configs/ebisu.h b/include/configs/ebisu.h
index 06cbb03dc6a..ee9ddb13362 100644
--- a/include/configs/ebisu.h
+++ b/include/configs/ebisu.h
@@ -22,4 +22,16 @@
 
 /* Environment in eMMC, at the end of 2nd "boot sector" */
 
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_MTD
+#define CONFIG_FLASH_SHOW_PROGRESS	45
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ 0x08000000 }
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT	1
+#define CONFIG_SYS_MAX_FLASH_SECT	256
+#define CONFIG_SYS_WRITE_SWAPPED_DATA
+
 #endif /* __EBISU_H */
diff --git a/include/configs/j721e_evm.h b/include/configs/j721e_evm.h
index c8a76037ff0..1b47e18b2f9 100644
--- a/include/configs/j721e_evm.h
+++ b/include/configs/j721e_evm.h
@@ -2,7 +2,7 @@
 /*
  * Configuration header file for K3 J721E EVM
  *
- * Copyright (C) 2018-2019 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2018-2020 Texas Instruments Incorporated - https://www.ti.com/
  *	Lokesh Vutla <[email protected]>
  */
 
@@ -23,8 +23,10 @@
 #if defined(CONFIG_TARGET_J721E_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SPL_TEXT_BASE +	\
 					 CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE)
+#define CONFIG_SYS_UBOOT_BASE		0x50280000
 /* Image load address in RAM for DFU boot*/
 #else
+#define CONFIG_SYS_UBOOT_BASE		0x50080000
 /*
  * Maximum size in memory allocated to the SPL BSS. Keep it as tight as
  * possible (to allow the build to go through), as this directly affects
@@ -81,16 +83,29 @@
 	"uuid_disk=${uuid_gpt_disk};" \
 	"name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"
 
+#ifdef CONFIG_SYS_K3_SPL_ATF
+#if defined(CONFIG_TARGET_J721E_R5_EVM)
+#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC				\
+	"addr_mainr5f0_0load=0x88000000\0"				\
+	"name_mainr5f0_0fw=/lib/firmware/j7-main-r5f0_0-fw\0"		\
+	"addr_mcur5f0_0load=0x89000000\0"				\
+	"name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0"
+#elif defined(CONFIG_TARGET_J7200_R5_EVM)
+#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC				\
+	"addr_mcur5f0_0load=0x89000000\0"				\
+	"name_mcur5f0_0fw=/lib/firmware/j7200-mcu-r5f0_0-fw\0"
+#endif /* CONFIG_TARGET_J721E_R5_EVM */
+#else
+#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC ""
+#endif /* CONFIG_SYS_K3_SPL_ATF */
+
 /* U-Boot MMC-specific configuration */
 #define EXTRA_ENV_J721E_BOARD_SETTINGS_MMC				\
 	"boot=mmc\0"							\
 	"mmcdev=1\0"							\
 	"bootpart=1:2\0"						\
 	"bootdir=/boot\0"						\
-	"addr_mainr5f0_0load=88000000\0"					\
-	"name_mainr5f0_0fw=/lib/firmware/j7-main-r5f0_0-fw\0"		\
-	"addr_mcur5f0_0load=89000000\0"					\
-	"name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0"		\
+	EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC				\
 	"rd_spec=-\0"							\
 	"init_mmc=run args_all args_mmc\0"				\
 	"get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \
@@ -109,15 +124,28 @@
 		"${bootdir}/${name_fit}\0"				\
 	"partitions=" PARTS_DEFAULT
 
+/* Set the default list of remote processors to boot */
+#if defined(CONFIG_TARGET_J721E_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
 #ifdef DEFAULT_RPROCS
 #undef DEFAULT_RPROCS
 #endif
+#endif
+
+#ifdef CONFIG_TARGET_J721E_A72_EVM
 #define DEFAULT_RPROCS	""						\
 		"3 /lib/firmware/j7-main-r5f0_1-fw "			\
 		"4 /lib/firmware/j7-main-r5f1_0-fw "			\
+		"5 /lib/firmware/j7-main-r5f1_1-fw "			\
 		"6 /lib/firmware/j7-c66_0-fw "				\
 		"7 /lib/firmware/j7-c66_1-fw "				\
 		"8 /lib/firmware/j7-c71_0-fw "
+#endif /* CONFIG_TARGET_J721E_A72_EVM */
+
+#ifdef CONFIG_TARGET_J7200_A72_EVM
+#define DEFAULT_RPROCS ""						\
+		"2 /lib/firmware/j7200-main-r5f0_0-fw "			\
+		"3 /lib/firmware/j7200-main-r5f0_1-fw "
+#endif /* CONFIG_TARGET_J7200_A72_EVM */
 
 /* set default dfu_bufsiz to 128KB (sector size of OSPI) */
 #define EXTRA_ENV_DFUARGS \
diff --git a/include/configs/km/km-mpc832x.h b/include/configs/km/km-mpc832x.h
index d7186ab9198..22dfb5da67b 100644
--- a/include/configs/km/km-mpc832x.h
+++ b/include/configs/km/km-mpc832x.h
@@ -11,20 +11,6 @@
 #define CONFIG_83XX_PCICLK		66000000
 
 /*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-
-/*
  * System IO Config
  */
 #define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
diff --git a/include/configs/km/km-mpc8360.h b/include/configs/km/km-mpc8360.h
index bdbb8bf6b59..798b1269605 100644
--- a/include/configs/km/km-mpc8360.h
+++ b/include/configs/km/km-mpc8360.h
@@ -7,20 +7,6 @@
  */
 
 /*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-
-/*
  * System IO Setup
  */
 #define CONFIG_SYS_SICRH		(SICRH_UC1EOBI | SICRH_UC2E1OBI)
diff --git a/include/configs/km/km-mpc83xx.h b/include/configs/km/km-mpc83xx.h
index 7c7f2d4ec01..7aacd37c8a7 100644
--- a/include/configs/km/km-mpc83xx.h
+++ b/include/configs/km/km-mpc83xx.h
@@ -61,16 +61,6 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
 
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
-
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_NUM_I2C_BUSES	4
diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index 1b74177b2f2..a9bf213d8b4 100644
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -12,24 +12,6 @@
 
 #include <linux/stringify.h>
 
-#if defined(CONFIG_TARGET_P1020MBG)
-#define CONFIG_BOARDNAME "P1020MBG-PC"
-#define CONFIG_VSC7385_ENET
-#define CONFIG_SLIC
-#define __SW_BOOT_MASK		0x03
-#define __SW_BOOT_NOR		0xe4
-#define __SW_BOOT_SD		0x54
-#define CONFIG_SYS_L2_SIZE	(256 << 10)
-#endif
-
-#if defined(CONFIG_TARGET_P1020UTM)
-#define CONFIG_BOARDNAME "P1020UTM-PC"
-#define __SW_BOOT_MASK		0x03
-#define __SW_BOOT_NOR		0xe0
-#define __SW_BOOT_SD		0x50
-#define CONFIG_SYS_L2_SIZE	(256 << 10)
-#endif
-
 #if defined(CONFIG_TARGET_P1020RDB_PC)
 #define CONFIG_BOARDNAME "P1020RDB-PC"
 #define CONFIG_NAND_FSL_ELBC
@@ -74,51 +56,6 @@
  */
 #endif
 
-#if defined(CONFIG_TARGET_P1021RDB)
-#define CONFIG_BOARDNAME "P1021RDB-PC"
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_VSC7385_ENET
-#define CONFIG_SYS_LBC_LBCR	0x00080000	/* Implement conversion of
-						addresses in the LBC */
-#define __SW_BOOT_MASK		0x03
-#define __SW_BOOT_NOR		0x5c
-#define __SW_BOOT_SPI		0x1c
-#define __SW_BOOT_SD		0x9c
-#define __SW_BOOT_NAND		0xec
-#define __SW_BOOT_PCIE		0x6c
-#define CONFIG_SYS_L2_SIZE	(256 << 10)
-/*
- * Dynamic MTD Partition support with mtdparts
- */
-#endif
-
-#if defined(CONFIG_TARGET_P1024RDB)
-#define CONFIG_BOARDNAME "P1024RDB"
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SLIC
-#define __SW_BOOT_MASK		0xf3
-#define __SW_BOOT_NOR		0x00
-#define __SW_BOOT_SPI		0x08
-#define __SW_BOOT_SD		0x04
-#define __SW_BOOT_NAND		0x0c
-#define CONFIG_SYS_L2_SIZE	(256 << 10)
-#endif
-
-#if defined(CONFIG_TARGET_P1025RDB)
-#define CONFIG_BOARDNAME "P1025RDB"
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SLIC
-
-#define CONFIG_SYS_LBC_LBCR	0x00080000	/* Implement conversion of
-						addresses in the LBC */
-#define __SW_BOOT_MASK		0xf3
-#define __SW_BOOT_NOR		0x00
-#define __SW_BOOT_SPI		0x08
-#define __SW_BOOT_SD		0x04
-#define __SW_BOOT_NAND		0x0c
-#define CONFIG_SYS_L2_SIZE	(256 << 10)
-#endif
-
 #if defined(CONFIG_TARGET_P2020RDB)
 #define CONFIG_BOARDNAME "P2020RDB-PC"
 #define CONFIG_NAND_FSL_ELBC
@@ -246,7 +183,7 @@
 #define CONFIG_SYS_SPD_BUS_NUM 1
 #define SPD_EEPROM_ADDRESS 0x52
 
-#if (defined(CONFIG_TARGET_P1020MBG) || defined(CONFIG_TARGET_P1020RDB_PD))
+#if defined(CONFIG_TARGET_P1020RDB_PD)
 #define CONFIG_SYS_SDRAM_SIZE_LAW	LAW_SIZE_2G
 #define CONFIG_CHIP_SELECTS_PER_CTRL	2
 #else
@@ -313,12 +250,9 @@
 /*
  * Local Bus Definitions
  */
-#if (defined(CONFIG_TARGET_P1020MBG) || defined(CONFIG_TARGET_P1020RDB_PD))
+#if defined(CONFIG_TARGET_P1020RDB_PD)
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* 64M */
 #define CONFIG_SYS_FLASH_BASE		0xec000000
-#elif defined(CONFIG_TARGET_P1020UTM)
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* 32M */
-#define CONFIG_SYS_FLASH_BASE		0xee000000
 #else
 #define CONFIG_SYS_MAX_FLASH_SECT	128	/* 16M */
 #define CONFIG_SYS_FLASH_BASE		0xef000000
@@ -451,6 +385,7 @@
 
 /* Vsc7385 switch */
 #ifdef CONFIG_VSC7385_ENET
+#define __VSCFW_ADDR			"vscfw_addr=ef000000"
 #define CONFIG_SYS_VSC7385_BASE		0xffb00000
 
 #ifdef CONFIG_PHYS_64BIT
@@ -654,42 +589,6 @@
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #endif /* CONFIG_QE */
 
-#ifdef CONFIG_TARGET_P1025RDB
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_MIIM_ADDRESS	(CONFIG_SYS_CCSRBAR + 0x82120)
-
-#undef CONFIG_UEC_ETH
-#define CONFIG_PHY_MODE_NEED_CHANGE
-
-#define CONFIG_UEC_ETH1	/* ETH1 */
-#define CONFIG_HAS_ETH0
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	0	/* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK	QE_CLK12 /* CLK12 for MII */
-#define CONFIG_SYS_UEC1_TX_CLK	QE_CLK9 /* CLK9 for MII */
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0x0	/* 0x0 for MII */
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif /* CONFIG_UEC_ETH1 */
-
-#define CONFIG_UEC_ETH5	/* ETH5 */
-#define CONFIG_HAS_ETH1
-
-#ifdef CONFIG_UEC_ETH5
-#define CONFIG_SYS_UEC5_UCC_NUM	4	/* UCC5 */
-#define CONFIG_SYS_UEC5_RX_CLK	QE_CLK_NONE
-#define CONFIG_SYS_UEC5_TX_CLK	QE_CLK13 /* CLK 13 for RMII */
-#define CONFIG_SYS_UEC5_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC5_PHY_ADDR	0x3	/* 0x3 for RMII */
-#define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC5_INTERFACE_SPEED	100
-#endif /* CONFIG_UEC_ETH5 */
-#endif /* CONFIG_TARGET_P1025RDB */
-
 /*
  * Environment
  */
@@ -809,6 +708,7 @@ i2c mw 18 3 __SW_BOOT_MASK 1; reset
 "ramdisk_size=120000\0"	\
 "map_lowernorbank=i2c dev 1; i2c mw 18 1 02 1; i2c mw 18 3 fd 1\0" \
 "map_uppernorbank=i2c dev 1; i2c mw 18 1 00 1; i2c mw 18 3 fd 1\0" \
+__stringify(__VSCFW_ADDR)"\0" \
 __stringify(__NOR_RST_CMD)"\0" \
 __stringify(__SPI_RST_CMD)"\0" \
 __stringify(__SD_RST_CMD)"\0" \
diff --git a/include/configs/salvator-x.h b/include/configs/salvator-x.h
index 240df9c63b9..db06fa5ffd6 100644
--- a/include/configs/salvator-x.h
+++ b/include/configs/salvator-x.h
@@ -19,4 +19,16 @@
 
 /* Environment in eMMC, at the end of 2nd "boot sector" */
 
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_MTD
+#define CONFIG_FLASH_SHOW_PROGRESS	45
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ 0x08000000 }
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT	1
+#define CONFIG_SYS_MAX_FLASH_SECT	256
+#define CONFIG_SYS_WRITE_SWAPPED_DATA
+
 #endif /* __SALVATOR_X_H */
diff --git a/include/configs/topic_miami.h b/include/configs/topic_miami.h
index 6e3953835d1..010d28ac86f 100644
--- a/include/configs/topic_miami.h
+++ b/include/configs/topic_miami.h
@@ -24,7 +24,6 @@
 
 /* No falcon support */
 #undef CONFIG_SPL_OS_BOOT
-#undef CONFIG_SPL_FPGA_SUPPORT
 
 /* FPGA commands that we don't use */
 
diff --git a/include/configs/ulcb.h b/include/configs/ulcb.h
index 15fb6272287..165c82d508e 100644
--- a/include/configs/ulcb.h
+++ b/include/configs/ulcb.h
@@ -19,4 +19,16 @@
 
 /* Environment in eMMC, at the end of 2nd "boot sector" */
 
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_MTD
+#define CONFIG_FLASH_SHOW_PROGRESS	45
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ 0x08000000 }
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT	1
+#define CONFIG_SYS_MAX_FLASH_SECT	256
+#define CONFIG_SYS_WRITE_SWAPPED_DATA
+
 #endif /* __ULCB_H */
diff --git a/include/configs/xilinx_versal.h b/include/configs/xilinx_versal.h
index d7255a05dff..8b416327b57 100644
--- a/include/configs/xilinx_versal.h
+++ b/include/configs/xilinx_versal.h
@@ -94,6 +94,18 @@
 # define BOOT_TARGET_DEVICES_MMC(func)
 #endif
 
+#if defined(CONFIG_CMD_PXE) && defined(CONFIG_CMD_DHCP)
+# define BOOT_TARGET_DEVICES_PXE(func)	func(PXE, pxe, na)
+#else
+# define BOOT_TARGET_DEVICES_PXE(func)
+#endif
+
+#if defined(CONFIG_CMD_DHCP)
+# define BOOT_TARGET_DEVICES_DHCP(func)	func(DHCP, dhcp, na)
+#else
+# define BOOT_TARGET_DEVICES_DHCP(func)
+#endif
+
 #if defined(CONFIG_ZYNQMP_GQSPI) || defined(CONFIG_CADENCE_OSPI_VERSAL)
 # define BOOT_TARGET_DEVICES_XSPI(func)	func(XSPI, xspi, 0)
 #else
@@ -135,8 +147,8 @@
 	BOOT_TARGET_DEVICES_MMC(func) \
 	BOOT_TARGET_DEVICES_XSPI(func) \
 	BOOT_TARGET_DEVICES_DFU_USB(func) \
-	func(PXE, pxe, na) \
-	func(DHCP, dhcp, na)
+	BOOT_TARGET_DEVICES_PXE(func) \
+	BOOT_TARGET_DEVICES_DHCP(func)
 
 #include <config_distro_bootcmd.h>