Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-marvell

- kirkwood: Add Pogoplug-V4 support (Tony)
- kirkwood: GoFlex Home : Use Marvell PHY driver (Tony)
- Another set of kwboot improvements (Pali)
- Minor misc stuff

2 files changed, 65 insertions, 23 deletions

diff --git a/include/configs/goflexhome.h b/include/configs/goflexhome.h
index 90e37d98535..c2795792683 100644
--- a/include/configs/goflexhome.h
+++ b/include/configs/goflexhome.h
@@ -1,5 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
+ * Copyright (C) 2022 Tony Dinh <[email protected]>
  * Copyright (C) 2013 Suriyan Ramasami <[email protected]>
  *
  * Based on dockstar.h originally written by
@@ -14,55 +15,40 @@
 #ifndef _CONFIG_GOFLEXHOME_H
 #define _CONFIG_GOFLEXHOME_H
 
+#include <linux/bitops.h>
+
 /*
  * Default GPIO configuration and LED status
  */
 #define GOFLEXHOME_OE_LOW               (~(0))
 #define GOFLEXHOME_OE_HIGH              (~(0))
-#define GOFLEXHOME_OE_VAL_LOW           (1 << 29)       /* USB_PWEN low */
-#define GOFLEXHOME_OE_VAL_HIGH          (1 << 17)       /* LED pin high */
-
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG         10
-#define MV88E1116_CPRSP_CR3_REG         21
-#define MV88E1116_MAC_CTRL_REG          21
-#define MV88E1116_PGADR_REG             22
-#define MV88E1116_RGMII_TXTM_CTRL       (1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL       (1 << 5)
+#define GOFLEXHOME_OE_VAL_LOW		BIT(29)		/* USB_PWEN low */
+#define GOFLEXHOME_OE_VAL_HIGH          BIT(17)		/* LED pin high */
 
 #include "mv-common.h"
 
 /*
- *  Environment variables configurations
- */
-/*
- * max 4k env size is enough, but in case of nand
- * it has to be rounded to sector size
- */
-
-/*
  * Default environment variables
  */
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"console=console=ttyS0,115200\0" \
 	"mtdids=nand0=orion_nand\0" \
-	"mtdparts="CONFIG_MTDPARTS_DEFAULT \
+	"mtdparts=" CONFIG_MTDPARTS_DEFAULT \
 	"kernel=/boot/uImage\0" \
 	"bootargs_root=ubi.mtd=root root=ubi0:root rootfstype=ubifs ro\0"
 
 /*
  * Ethernet Driver configuration
  */
-#ifdef CONFIG_CMD_NET
 #define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
 #define CONFIG_PHY_BASE_ADR	0
-#endif /* CONFIG_CMD_NET */
+#ifdef CONFIG_RESET_PHY_R
+#undef CONFIG_RESET_PHY_R      /* remove legacy reset_phy() */
+#endif
 
 /* SATA driver configuration */
-#ifdef CONFIG_SATA
 #define CONFIG_SYS_SATA_MAX_DEVICE	1
 #define CONFIG_LBA48
-#endif /* CONFIG_SATA */
 
 #endif /* _CONFIG_GOFLEXHOME_H */
diff --git a/include/configs/pogo_v4.h b/include/configs/pogo_v4.h
new file mode 100644
index 00000000000..568a93623db
--- /dev/null
+++ b/include/configs/pogo_v4.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2014-2022 Tony Dinh <[email protected]>
+ *
+ * Based on
+ * Copyright (C) 2012
+ * David Purdy <[email protected]>
+ *
+ * Based on Kirkwood support:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ */
+
+#ifndef _CONFIG_POGO_V4_H
+#define _CONFIG_POGO_V4_H
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"dtb_file=/boot/dts/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
+	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"\
+	"mtdids=nand0=orion_nand\0"\
+	"bootargs_console=console=ttyS0,115200\0" \
+	"bootcmd_usb=usb start; load usb 0:1 0x00800000 /boot/uImage; " \
+	"load usb 0:1 0x01100000 /boot/uInitrd; " \
+	"load usb 0:1 0x2c00000 $dtb_file\0"
+
+/*
+ * Ethernet Driver configuration
+ */
+#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR	0
+#ifdef CONFIG_RESET_PHY_R
+#undef CONFIG_RESET_PHY_R	/* remove legacy reset_phy() */
+#endif
+
+/*
+ *  SATA Driver configuration
+ */
+#define CONFIG_SYS_SATA_MAX_DEVICE	1
+
+/*
+ * Support large disk for SATA and USB
+ */
+#define CONFIG_SYS_64BIT_LBA
+#define CONFIG_LBA48
+
+#endif /* _CONFIG_POGO_V4_H */