Merge branch '2021-10-01-assorted-removal-and-migration' into next

- Remove the last non-CONFIG_DM boards, and their related unused code.
- Finish a few partial migrations to Kconfig, and remove some redundant
  serial related code.

43 files changed, 0 insertions, 1096 deletions

diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
deleted file mode 100644
index dd11e9841e9..00000000000
--- a/include/configs/MPC8349EMDS.h
+++ /dev/null
@@ -1,315 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2006-2010
- * Wolfgang Denk, DENX Software Engineering, [email protected].
- */
-
-/*
- * mpc8349emds board configuration file
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300		1	/* E300 Family */
-
-#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
-
-/*
- * DDR Setup
- */
-#define CONFIG_SPD_EEPROM		/* use SPD EEPROM for DDR setup*/
-
-/*
- * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver
- * unselect it to use old spd_sdram.c
- */
-#define CONFIG_SYS_SPD_BUS_NUM	0
-#define SPD_EEPROM_ADDRESS1	0x52
-#define SPD_EEPROM_ADDRESS2	0x51
-#define CONFIG_DIMM_SLOTS_PER_CTLR	2
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
-
-#define CONFIG_SYS_SDRAM_BASE	0x00000000	/* DDR is system memory*/
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
-					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-/*
- * DDRCDR - DDR Control Driver Register
- */
-#define CONFIG_SYS_DDRCDR_VALUE	0x80080001
-
-#if defined(CONFIG_SPD_EEPROM)
-/*
- * Determine DDR configuration from I2C interface.
- */
-#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
-#else
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_SYS_DDR_SIZE		256		/* MB */
-#define CONFIG_SYS_DDR_CS2_CONFIG	(CSCONFIG_EN \
-				| CSCONFIG_ROW_BIT_13 \
-				| CSCONFIG_COL_BIT_10)
-#define CONFIG_SYS_DDR_TIMING_1	0x36332321
-#define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-#define CONFIG_SYS_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
-#define CONFIG_SYS_DDR_INTERVAL	0x04060100	/* autocharge,no open page */
-
-/* the default burst length is 4 - for 64-bit data path */
-				/* DLL,normal,seq,4/2.5, 4 burst len */
-#define CONFIG_SYS_DDR_MODE	0x00000022
-#endif
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE	0xF0000000	/* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_BASE		0xFE000000	/* start of FLASH   */
-#define CONFIG_SYS_FLASH_SIZE		32	/* max flash size in MB */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef  CONFIG_SYS_RAMBOOT
-#endif
-
-/*
- * BCSR register on local bus 32KB, 8-bit wide for MDS config reg
- */
-#define CONFIG_SYS_BCSR			0xE2400000
-					/* Access window base at BCSR base */
-
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000	/* Initial RAM addr */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	\
-			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)	/* Reserve 512 kB for Mon */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE    1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
-
-/* SPI */
-#undef CONFIG_SOFT_SPI			/* SPI bit-banged */
-
-/* GPIOs.  Used as SPI chip selects */
-#define CONFIG_SYS_GPIO1_PRELIM
-#define CONFIG_SYS_GPIO1_DIR		0xC0000000  /* SPI CS on 0, LED on 1 */
-#define CONFIG_SYS_GPIO1_DAT		0xC0000000  /* Both are active LOW */
-
-/* TSEC */
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/* USB */
-#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY	1 /* Use SYS board PHY */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
-#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */
-
-#define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
-#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
-#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
-#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
-#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI2_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
-#define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */
-
-#if defined(CONFIG_PCI)
-
-#if !defined(CONFIG_PCI_PNP)
-	#define PCI_ENET0_IOADDR	0xFIXME
-	#define PCI_ENET0_MEMADDR	0xFIXME
-	#define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-
-#endif	/* CONFIG_PCI */
-
-/*
- * TSEC configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_GMII		1	/* MII PHY management */
-#define CONFIG_TSEC1		1
-#define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2		1
-#define CONFIG_TSEC2_NAME	"TSEC1"
-#define TSEC1_PHY_ADDR		0
-#define TSEC2_PHY_ADDR		1
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME		"TSEC0"
-
-#endif	/* CONFIG_TSEC_ENET */
-
-/*
- * Configure on-board RTC
- */
-#define CONFIG_RTC_DS1374		/* use ds1374 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68	/* at address 0x68 */
-
-/*
- * Environment
- */
-#ifndef CONFIG_SYS_RAMBOOT
-/* Address and size of Redundant Environment Sector	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-				/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
-
-/*
- * System performance
- */
-#define CONFIG_SYS_SCCR_TSEC1CM	1	/* TSEC1 clock mode (0-3) */
-#define CONFIG_SYS_SCCR_TSEC2CM	1	/* TSEC2 & I2C0 clock mode (0-3) */
-
-/* System IO Config */
-#define CONFIG_SYS_SICRH 0
-#define CONFIG_SYS_SICRL SICRL_LDP_A
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH0
-#endif
-
-#define CONFIG_HOSTNAME		"mpc8349emds"
-#define CONFIG_ROOTPATH		"/nfsroot/rootfs"
-#define CONFIG_BOOTFILE		"uImage"
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=mpc8349emds\0"					\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
-		"bootm\0"						\
-	"load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0"		\
-	"update=protect off fe000000 fe03ffff; "			\
-		"era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\
-	"upd=run load update\0"						\
-	"fdtaddr=780000\0"						\
-	"fdtfile=mpc834x_mds.dtb\0"					\
-	""
-
-#define NFSBOOTCOMMAND						\
-	"setenv bootargs root=/dev/nfs rw "				\
-		"nfsroot=$serverip:$rootpath "				\
-		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
-							"$netdev:off "	\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr - $fdtaddr"
-
-#define RAMBOOTCOMMAND						\
-	"setenv bootargs root=/dev/ram rw "				\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $ramdiskaddr $ramdiskfile;"				\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8349EMDS_SDRAM.h b/include/configs/MPC8349EMDS_SDRAM.h
deleted file mode 100644
index 2a53b14d0b2..00000000000
--- a/include/configs/MPC8349EMDS_SDRAM.h
+++ /dev/null
@@ -1,372 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2006-2010
- * Wolfgang Denk, DENX Software Engineering, [email protected].
- */
-
-/*
- * mpc8349emds board configuration file
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300		1	/* E300 Family */
-
-#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
-
-/*
- * DDR Setup
- */
-#define CONFIG_SPD_EEPROM		/* use SPD EEPROM for DDR setup*/
-
-/*
- * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver
- * unselect it to use old spd_sdram.c
- */
-#define CONFIG_SYS_SPD_BUS_NUM	0
-#define SPD_EEPROM_ADDRESS1	0x52
-#define SPD_EEPROM_ADDRESS2	0x51
-#define CONFIG_DIMM_SLOTS_PER_CTLR	2
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
-
-#define CONFIG_SYS_SDRAM_BASE	0x00000000	/* DDR is system memory*/
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
-					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-/*
- * DDRCDR - DDR Control Driver Register
- */
-#define CONFIG_SYS_DDRCDR_VALUE	0x80080001
-
-#if defined(CONFIG_SPD_EEPROM)
-/*
- * Determine DDR configuration from I2C interface.
- */
-#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
-#else
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_SYS_DDR_SIZE		256		/* MB */
-#define CONFIG_SYS_DDR_CS2_CONFIG	(CSCONFIG_EN \
-				| CSCONFIG_ROW_BIT_13 \
-				| CSCONFIG_COL_BIT_10)
-#define CONFIG_SYS_DDR_TIMING_1	0x36332321
-#define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-#define CONFIG_SYS_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
-#define CONFIG_SYS_DDR_INTERVAL	0x04060100	/* autocharge,no open page */
-
-/* the default burst length is 4 - for 64-bit data path */
-				/* DLL,normal,seq,4/2.5, 4 burst len */
-#define CONFIG_SYS_DDR_MODE	0x00000022
-#endif
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE	0xF0000000	/* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_BASE		0xFE000000	/* start of FLASH   */
-#define CONFIG_SYS_FLASH_SIZE		32	/* max flash size in MB */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef  CONFIG_SYS_RAMBOOT
-#endif
-
-/*
- * BCSR register on local bus 32KB, 8-bit wide for MDS config reg
- */
-#define CONFIG_SYS_BCSR			0xE2400000
-					/* Access window base at BCSR base */
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000	/* Initial RAM addr */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	\
-			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)	/* Reserve 512 kB for Mon */
-
-/*
- * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory.
- */
-
-/* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */
-/*
- * Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
- *
- * For BR2, need:
- *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
- *    port-size = 32-bits = BR2[19:20] = 11
- *    no parity checking = BR2[21:22] = 00
- *    SDRAM for MSEL = BR2[24:26] = 011
- *    Valid = BR[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
- */
-
-/*
- * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
- *
- * For OR2, need:
- *    64MB mask for AM, OR2[0:7] = 1111 1100
- *                 XAM, OR2[17:18] = 11
- *    9 columns OR2[19-21] = 010
- *    13 rows   OR2[23-25] = 100
- *    EAD set for extra time OR[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
- */
-
-
-				/* LB sdram refresh timer, about 6us */
-#define CONFIG_SYS_LBC_LSRT	0x32000000
-				/* LB refresh timer prescal, 266MHz/32 */
-#define CONFIG_SYS_LBC_MRTPR	0x20000000
-
-#define CONFIG_SYS_LBC_LSDMR_COMMON    (LSDMR_RFEN	\
-				| LSDMR_BSMA1516	\
-				| LSDMR_RFCR8		\
-				| LSDMR_PRETOACT6	\
-				| LSDMR_ACTTORW3	\
-				| LSDMR_BL8		\
-				| LSDMR_WRC3		\
-				| LSDMR_CL3)
-
-/*
- * SDRAM Controller configuration sequence.
- */
-#define CONFIG_SYS_LBC_LSDMR_1	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
-#define CONFIG_SYS_LBC_LSDMR_2	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
-#define CONFIG_SYS_LBC_LSDMR_3	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
-#define CONFIG_SYS_LBC_LSDMR_4	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
-#define CONFIG_SYS_LBC_LSDMR_5	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE    1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
-
-/* SPI */
-#undef CONFIG_SOFT_SPI			/* SPI bit-banged */
-
-/* GPIOs.  Used as SPI chip selects */
-#define CONFIG_SYS_GPIO1_PRELIM
-#define CONFIG_SYS_GPIO1_DIR		0xC0000000  /* SPI CS on 0, LED on 1 */
-#define CONFIG_SYS_GPIO1_DAT		0xC0000000  /* Both are active LOW */
-
-/* TSEC */
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/* USB */
-#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY	1 /* Use SYS board PHY */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
-#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */
-
-#define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
-#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
-#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
-#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
-#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI2_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
-#define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */
-
-#if defined(CONFIG_PCI)
-
-#if !defined(CONFIG_PCI_PNP)
-	#define PCI_ENET0_IOADDR	0xFIXME
-	#define PCI_ENET0_MEMADDR	0xFIXME
-	#define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-
-#endif	/* CONFIG_PCI */
-
-/*
- * TSEC configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_GMII		1	/* MII PHY management */
-#define CONFIG_TSEC1		1
-#define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2		1
-#define CONFIG_TSEC2_NAME	"TSEC1"
-#define TSEC1_PHY_ADDR		0
-#define TSEC2_PHY_ADDR		1
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME		"TSEC0"
-
-#endif	/* CONFIG_TSEC_ENET */
-
-/*
- * Configure on-board RTC
- */
-#define CONFIG_RTC_DS1374		/* use ds1374 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68	/* at address 0x68 */
-
-/*
- * Environment
- */
-#ifndef CONFIG_SYS_RAMBOOT
-/* Address and size of Redundant Environment Sector	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-				/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
-
-/*
- * System performance
- */
-#define CONFIG_SYS_SPCR_TSEC1EP	3	/* TSEC1 emergency priority (0-3) */
-#define CONFIG_SYS_SPCR_TSEC2EP	3	/* TSEC2 emergency priority (0-3) */
-#define CONFIG_SYS_SCCR_TSEC1CM	1	/* TSEC1 clock mode (0-3) */
-#define CONFIG_SYS_SCCR_TSEC2CM	1	/* TSEC2 & I2C0 clock mode (0-3) */
-
-/* System IO Config */
-#define CONFIG_SYS_SICRH 0
-#define CONFIG_SYS_SICRL SICRL_LDP_A
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH0
-#endif
-
-#define CONFIG_HOSTNAME		"mpc8349emds"
-#define CONFIG_ROOTPATH		"/nfsroot/rootfs"
-#define CONFIG_BOOTFILE		"uImage"
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=mpc8349emds\0"					\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
-		"bootm\0"						\
-	"load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0"		\
-	"update=protect off fe000000 fe03ffff; "			\
-		"era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\
-	"upd=run load update\0"						\
-	"fdtaddr=780000\0"						\
-	"fdtfile=mpc834x_mds.dtb\0"					\
-	""
-
-#define NFSBOOTCOMMAND						\
-	"setenv bootargs root=/dev/nfs rw "				\
-		"nfsroot=$serverip:$rootpath "				\
-		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
-							"$netdev:off "	\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr - $fdtaddr"
-
-#define RAMBOOTCOMMAND						\
-	"setenv bootargs root=/dev/ram rw "				\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $ramdiskaddr $ramdiskfile;"				\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h
index 26c6180d3a5..72119a1cf04 100644
--- a/include/configs/MPC837XERDB.h
+++ b/include/configs/MPC837XERDB.h
@@ -321,10 +321,6 @@
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index fc9d94984e2..fe156e78157 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -288,10 +288,6 @@
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index f7d05ffa89a..5c54bad4964 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -415,10 +415,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index e1e0717991d..3a9ea032921 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -278,10 +278,6 @@
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index 02b0b71ada5..922f0661aba 100644
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -619,10 +619,6 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20) /* Initial Memory map for Linux */
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20) /* Increase max gunzip size */
 
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h
index 6da44e7ab82..1e75066eb1c 100644
--- a/include/configs/P2041RDB.h
+++ b/include/configs/P2041RDB.h
@@ -466,10 +466,6 @@ unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory for Linux */
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h
index 3ae8a14c944..e4629946ddb 100644
--- a/include/configs/T102xRDB.h
+++ b/include/configs/T102xRDB.h
@@ -584,10 +584,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h
index 910baef00c4..7c48c3af71f 100644
--- a/include/configs/T104xRDB.h
+++ b/include/configs/T104xRDB.h
@@ -592,10 +592,6 @@
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
 /*
  * Dynamic MTD Partition support with mtdparts
  */
diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h
index 315d1f7b01a..57640acfc90 100644
--- a/include/configs/T208xQDS.h
+++ b/include/configs/T208xQDS.h
@@ -585,11 +585,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h
index 6824be9e758..6f27386d2ba 100644
--- a/include/configs/T208xRDB.h
+++ b/include/configs/T208xRDB.h
@@ -540,11 +540,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/T4240RDB.h b/include/configs/T4240RDB.h
index 54db021ec9a..b7cbf87d306 100644
--- a/include/configs/T4240RDB.h
+++ b/include/configs/T4240RDB.h
@@ -214,10 +214,6 @@
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/amcore.h b/include/configs/amcore.h
index 428c2f7fd72..98ad047bc4c 100644
--- a/include/configs/amcore.h
+++ b/include/configs/amcore.h
@@ -13,7 +13,6 @@
 #define CONFIG_MCFTMR
 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		0
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
 #define CONFIG_BOOTCOMMAND		"bootm ffc20000"
 #define CONFIG_EXTRA_ENV_SETTINGS				\
diff --git a/include/configs/ap121.h b/include/configs/ap121.h
index fb2a0b33cc0..f3fc53ba484 100644
--- a/include/configs/ap121.h
+++ b/include/configs/ap121.h
@@ -21,9 +21,6 @@
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE - 1)
 
-#define CONFIG_SYS_BAUDRATE_TABLE \
-	{9600, 19200, 38400, 57600, 115200}
-
 #define CONFIG_BOOTCOMMAND              "sf probe;" \
 					"mtdparts default;" \
 					"bootm 0x9f650000"
diff --git a/include/configs/ap143.h b/include/configs/ap143.h
index bb9544b8e74..fa13a801b77 100644
--- a/include/configs/ap143.h
+++ b/include/configs/ap143.h
@@ -25,8 +25,6 @@
  * Serial Port
  */
 #define CONFIG_SYS_NS16550_CLK          25000000
-#define CONFIG_SYS_BAUDRATE_TABLE \
-	{9600, 19200, 38400, 57600, 115200}
 
 #define CONFIG_BOOTCOMMAND              "sf probe;" \
 					"mtdparts default;" \
diff --git a/include/configs/ap152.h b/include/configs/ap152.h
index 766f10b6bea..3eaf19283bb 100644
--- a/include/configs/ap152.h
+++ b/include/configs/ap152.h
@@ -25,8 +25,6 @@
  * Serial Port
  */
 #define CONFIG_SYS_NS16550_CLK          25000000
-#define CONFIG_SYS_BAUDRATE_TABLE \
-	{9600, 19200, 38400, 57600, 115200}
 
 #define CONFIG_BOOTCOMMAND              "sf probe;" \
 					"mtdparts default;" \
diff --git a/include/configs/aspenite.h b/include/configs/aspenite.h
deleted file mode 100644
index 4a25d561653..00000000000
--- a/include/configs/aspenite.h
+++ /dev/null
@@ -1,30 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2010
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <[email protected]>
- * Contributor: Mahavir Jain <[email protected]>
- */
-
-#ifndef __CONFIG_ASPENITE_H
-#define __CONFIG_ASPENITE_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_SHEEVA_88SV331xV5	1	/* CPU Core subversion */
-#define CONFIG_ARMADA100		1	/* SOC Family Name */
-
-/*
- * There is no internal RAM in ARMADA100, using DRAM
- * TBD: dcache to be used for this
- */
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
-
-#include "mv-common.h"
-
-/*
- * Environment variables configurations
- */
-
-#endif	/* __CONFIG_ASPENITE_H */
diff --git a/include/configs/bg0900.h b/include/configs/bg0900.h
deleted file mode 100644
index d9599b85911..00000000000
--- a/include/configs/bg0900.h
+++ /dev/null
@@ -1,39 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2013 Marek Vasut <[email protected]>
- */
-#ifndef __CONFIGS_BG0900_H__
-#define __CONFIGS_BG0900_H__
-
-/* Memory configuration */
-#define PHYS_SDRAM_1			0x40000000	/* Base address */
-#define PHYS_SDRAM_1_SIZE		0x10000000	/* Max 256 MB RAM */
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-
-/* Environment */
-
-/* FEC Ethernet on SoC */
-#ifdef	CONFIG_CMD_NET
-#define CONFIG_FEC_MXC
-#endif
-
-/* Boot Linux */
-#define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_BOOTCOMMAND	"bootm"
-
-/* Extra Environment */
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"update_spi_firmware_filename=u-boot.sb\0"			\
-	"update_spi_firmware_maxsz=0x80000\0"				\
-	"update_spi_firmware="	/* Update the SPI flash firmware */	\
-		"if sf probe 2:0 ; then "				\
-		"if tftp ${update_spi_firmware_filename} ; then "	\
-		"sf erase 0x0 +${filesize} ; "				\
-		"sf write ${loadaddr} 0x0 ${filesize} ; "		\
-		"fi ; "							\
-		"fi\0"
-
-/* The rest of the configuration is shared */
-#include <configs/mxs.h>
-
-#endif /* __CONFIGS_BG0900_H__ */
diff --git a/include/configs/cgtqmx8.h b/include/configs/cgtqmx8.h
index 304c876e8b9..4012814988d 100644
--- a/include/configs/cgtqmx8.h
+++ b/include/configs/cgtqmx8.h
@@ -159,9 +159,6 @@
 #define PHYS_SDRAM_1_SIZE		0x80000000	/* 2 GB */
 #define PHYS_SDRAM_2_SIZE		0x100000000	/* 4 GB */
 
-/* Serial */
-#define CONFIG_BAUDRATE			115200
-
 /* Generic Timer Definitions */
 #define COUNTER_FREQUENCY		8000000	/* 8MHz */
 
diff --git a/include/configs/cm_fx6.h b/include/configs/cm_fx6.h
index a22fd0ee1fe..d40c3a9c3e5 100644
--- a/include/configs/cm_fx6.h
+++ b/include/configs/cm_fx6.h
@@ -32,7 +32,6 @@
 
 /* Serial console */
 #define CONFIG_MXC_UART_BASE		UART4_BASE
-#define CONFIG_SYS_BAUDRATE_TABLE	{9600, 19200, 38400, 57600, 115200}
 
 /* Environment */
 
diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h
index 01f4dba9e92..79fca968dc0 100644
--- a/include/configs/corenet_ds.h
+++ b/include/configs/corenet_ds.h
@@ -466,10 +466,6 @@
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/flea3.h b/include/configs/flea3.h
deleted file mode 100644
index 6c3b2c4bf55..00000000000
--- a/include/configs/flea3.h
+++ /dev/null
@@ -1,155 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2011, Stefano Babic <[email protected]>
- *
- * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
- *
- * Copyright (C) 2007, Guennadi Liakhovetski <[email protected]>
- *
- * Configuration for the flea3 board.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/imx-regs.h>
-
- /* High Level Configuration Options */
-#define CONFIG_MX35
-
-/* Set TEXT at the beginning of the NOR flash */
-
-/* This is required to setup the ESDC controller */
-
-/*
- * Hardware drivers
- */
-#define CONFIG_SYS_SPD_BUS_NUM		2 /* I2C3 */
-
-/*
- * UART (console)
- */
-#define CONFIG_MXC_UART_BASE	UART3_BASE
-
-/*
- * Command definition
- */
-
-#define CONFIG_NET_RETRY_COUNT	100
-
-/*
- * Ethernet on SOC (FEC)
- */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE	FEC_BASE_ADDR
-#define CONFIG_FEC_MXC_PHYADDR	0x1
-
-#define CONFIG_ARP_TIMEOUT	200UL
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_CBSIZE	512	/* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	32	/* max number of command args */
-
-/*
- * Physical Memory Map
- */
-#define PHYS_SDRAM_1		CSD0_BASE_ADDR
-#define PHYS_SDRAM_1_SIZE	(128 * 1024 * 1024)
-
-#define CONFIG_SYS_SDRAM_BASE		CSD0_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_ADDR	(IRAM_BASE_ADDR + 0x10000)
-#define CONFIG_SYS_INIT_RAM_SIZE		(IRAM_SIZE / 2)
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
-					CONFIG_SYS_GBL_DATA_OFFSET)
-
-/*
- * MTD Command for mtdparts
- */
-
-/*
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE		CS0_BASE_ADDR
-#define CONFIG_SYS_MAX_FLASH_BANKS 1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512	/* max number of sectors on one chip */
-/* Monitor at beginning of flash */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
-
-/* Address and size of Redundant Environment Sector	*/
-
-/*
- * CFI FLASH driver setup
- */
-
-/* A non-standard buffered write algorithm */
-
-/*
- * NAND FLASH driver setup
- */
-#define CONFIG_MXC_NAND_REGS_BASE	(NFC_BASE_ADDR)
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		(NFC_BASE_ADDR)
-#define CONFIG_MXC_NAND_HWECC
-#define CONFIG_SYS_NAND_LARGEPAGE
-
-/*
- * Default environment and default scripts
- * to update uboot and load kernel
- */
-
-#define CONFIG_HOSTNAME "flea3"
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip_sta=setenv bootargs ${bootargs} "			\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"		\
-	"addip=if test -n ${ipdyn};then run addip_dyn;"			\
-		"else run addip_sta;fi\0"				\
-	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
-	"addtty=setenv bootargs ${bootargs}"				\
-		" console=ttymxc2,${baudrate}\0"			\
-	"addmisc=setenv bootargs ${bootargs} ${misc}\0"			\
-	"loadaddr=80800000\0"						\
-	"kernel_addr_r=80800000\0"					\
-	"hostname=" CONFIG_HOSTNAME "\0"			\
-	"bootfile=" CONFIG_HOSTNAME "/uImage\0"		\
-	"ramdisk_file=" CONFIG_HOSTNAME "/uRamdisk\0"	\
-	"flash_self=run ramargs addip addtty addmtd addmisc;"		\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"flash_nfs=run nfsargs addip addtty addmtd addmisc;"		\
-		"bootm ${kernel_addr}\0"				\
-	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
-		"run nfsargs addip addtty addmtd addmisc;"		\
-		"bootm ${kernel_addr_r}\0"				\
-	"net_self_load=tftp ${kernel_addr_r} ${bootfile};"		\
-		"tftp ${ramdisk_addr_r} ${ramdisk_file};\0"		\
-	"net_self=if run net_self_load;then "				\
-		"run ramargs addip addtty addmtd addmisc;"		\
-		"bootm ${kernel_addr_r} ${ramdisk_addr_r};"		\
-		"else echo Images not loades;fi\0"			\
-	"u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0"		\
-	"load=tftp ${loadaddr} ${u-boot}\0"				\
-	"uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0"		\
-	"update=protect off ${uboot_addr} +80000;"			\
-		"erase ${uboot_addr} +80000;"				\
-		"cp.b ${loadaddr} ${uboot_addr} ${filesize}\0"		\
-	"upd=if run load;then echo Updating u-boot;if run update;"	\
-		"then echo U-Boot updated;"				\
-			"else echo Error updating u-boot !;"		\
-			"echo Board without bootloader !!;"		\
-		"fi;"							\
-		"else echo U-Boot not downloaded..exiting;fi\0"		\
-	"bootcmd=run net_nfs\0"
-
-#endif				/* __CONFIG_H */
diff --git a/include/configs/kontron_sl28.h b/include/configs/kontron_sl28.h
index 438a189702d..6769592101d 100644
--- a/include/configs/kontron_sl28.h
+++ b/include/configs/kontron_sl28.h
@@ -45,7 +45,6 @@
 
 /* serial port */
 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0) / 2)
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
 #define CONFIG_SYS_CLK_FREQ		100000000
 #define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ / 4)
diff --git a/include/configs/ls1012a_common.h b/include/configs/ls1012a_common.h
index 1edea0a2b2f..8a49f2d0075 100644
--- a/include/configs/ls1012a_common.h
+++ b/include/configs/ls1012a_common.h
@@ -59,8 +59,6 @@
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
 
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
 #define CONFIG_SYS_HZ			1000
 
 #define CONFIG_HWCONFIG
diff --git a/include/configs/ls1028a_common.h b/include/configs/ls1028a_common.h
index 50edefb3632..1401264f931 100644
--- a/include/configs/ls1028a_common.h
+++ b/include/configs/ls1028a_common.h
@@ -45,8 +45,6 @@
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0) / 2)
 
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
 /* Miscellaneous configurable options */
 
 /* Physical Memory Map */
diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h
index 6cae6c13960..fb697bdf130 100644
--- a/include/configs/ls1043a_common.h
+++ b/include/configs/ls1043a_common.h
@@ -54,8 +54,6 @@
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
 
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
 /* SD boot SPL */
 #ifdef CONFIG_SD_BOOT
 
diff --git a/include/configs/ls1046a_common.h b/include/configs/ls1046a_common.h
index 1d8adf97d3c..f0bde08f246 100644
--- a/include/configs/ls1046a_common.h
+++ b/include/configs/ls1046a_common.h
@@ -54,8 +54,6 @@
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
 
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
 /* SD boot SPL */
 #ifdef CONFIG_SD_BOOT
 #define CONFIG_SPL_MAX_SIZE		0x1f000		/* 124 KiB */
diff --git a/include/configs/ls1088a_common.h b/include/configs/ls1088a_common.h
index f39f0316c59..9ae0b8e0ae4 100644
--- a/include/configs/ls1088a_common.h
+++ b/include/configs/ls1088a_common.h
@@ -63,8 +63,6 @@
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0) / 2)
 
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
 #if !defined(SPL_NO_IFC) || defined(CONFIG_TARGET_LS1088AQDS)
 /* IFC */
 #define CONFIG_FSL_IFC
diff --git a/include/configs/ls2080a_common.h b/include/configs/ls2080a_common.h
index 770f2aaf6f9..6d9ae9d987e 100644
--- a/include/configs/ls2080a_common.h
+++ b/include/configs/ls2080a_common.h
@@ -74,8 +74,6 @@
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
 
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
 /* IFC */
 #define CONFIG_FSL_IFC
 
diff --git a/include/configs/lx2160a_common.h b/include/configs/lx2160a_common.h
index 4db19e26c15..dddac7b05c3 100644
--- a/include/configs/lx2160a_common.h
+++ b/include/configs/lx2160a_common.h
@@ -67,7 +67,6 @@
 					(void *)CONFIG_SYS_SERIAL1, \
 					(void *)CONFIG_SYS_SERIAL2, \
 					(void *)CONFIG_SYS_SERIAL3 }
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
 /* MC firmware */
 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH		0x20000
diff --git a/include/configs/mt7620.h b/include/configs/mt7620.h
index b05ac0ade5b..a2de0342921 100644
--- a/include/configs/mt7620.h
+++ b/include/configs/mt7620.h
@@ -24,9 +24,6 @@
 #define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_CBSIZE		1024
 
-/* Serial common */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
 /* SPL */
 
 #define CONFIG_SYS_UBOOT_START		CONFIG_SYS_TEXT_BASE
diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index 49dbbf07f88..58336110568 100644
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -597,10 +597,6 @@
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/pxa-common.h b/include/configs/pxa-common.h
index 52d77e06acf..7a78f98eb15 100644
--- a/include/configs/pxa-common.h
+++ b/include/configs/pxa-common.h
@@ -9,13 +9,6 @@
 #define	__CONFIG_PXA_COMMON_H__
 
 /*
- * KGDB
- */
-#ifdef	CONFIG_CMD_KGDB
-#define	CONFIG_KGDB_BAUDRATE		230400
-#endif
-
-/*
  * OHCI USB
  */
 #ifdef	CONFIG_CMD_USB
diff --git a/include/configs/s5p4418_nanopi2.h b/include/configs/s5p4418_nanopi2.h
index c482de122ba..21feba0569e 100644
--- a/include/configs/s5p4418_nanopi2.h
+++ b/include/configs/s5p4418_nanopi2.h
@@ -113,7 +113,6 @@
 					 (void *)PHY_BASEADDR_UART1, \
 					 (void *)PHY_BASEADDR_UART2, \
 					 (void *)PHY_BASEADDR_UART3}
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
 /*-----------------------------------------------------------------------
  * PLL
diff --git a/include/configs/socrates.h b/include/configs/socrates.h
index 4fd119ce854..454dbd30b61 100644
--- a/include/configs/socrates.h
+++ b/include/configs/socrates.h
@@ -203,10 +203,6 @@
  */
 #define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux	*/
 
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port*/
-#endif
-
 
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
diff --git a/include/configs/stmark2.h b/include/configs/stmark2.h
index 5516ecfcdf5..a71de054589 100644
--- a/include/configs/stmark2.h
+++ b/include/configs/stmark2.h
@@ -12,7 +12,6 @@
 
 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		0
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
 
 #define LDS_BOARD_TEXT						\
 	board/sysam/stmark2/sbf_dram_init.o (.text*)
diff --git a/include/configs/synquacer.h b/include/configs/synquacer.h
index 225d017d17d..13e9c64387e 100644
--- a/include/configs/synquacer.h
+++ b/include/configs/synquacer.h
@@ -49,9 +49,6 @@
 #define CONFIG_SYS_MEMTEST_START	(CONFIG_SYS_SDRAM_BASE + (512 * 1024))
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + PHYS_SDRAM_SIZE)
 
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_SYS_BAUDRATE_TABLE	{115200, 19200, 38400, 57600, 9600 }
-
 #define CONFIG_SYS_CBSIZE		1024
 #define CONFIG_SYS_MAXARGS		128
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
diff --git a/include/configs/tplink_wdr4300.h b/include/configs/tplink_wdr4300.h
index 32689e1aecf..f9a0b7d1aaa 100644
--- a/include/configs/tplink_wdr4300.h
+++ b/include/configs/tplink_wdr4300.h
@@ -25,8 +25,6 @@
  * Serial Port
  */
 #define CONFIG_SYS_NS16550_CLK		40000000
-#define CONFIG_SYS_BAUDRATE_TABLE \
-	{9600, 19200, 38400, 57600, 115200}
 
 #define CONFIG_BOOTCOMMAND		\
 	"dhcp 192.168.1.1:wdr4300.fit && bootm $loadaddr"
diff --git a/include/configs/vexpress_common.h b/include/configs/vexpress_common.h
index 02fd9636110..990f5ed5470 100644
--- a/include/configs/vexpress_common.h
+++ b/include/configs/vexpress_common.h
@@ -123,7 +123,6 @@
 #define CONFIG_PL01x_PORTS		{(void *)CONFIG_SYS_SERIAL0, \
 					 (void *)CONFIG_SYS_SERIAL1}
 
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 #define CONFIG_SYS_SERIAL0		V2M_UART0
 #define CONFIG_SYS_SERIAL1		V2M_UART1
 
diff --git a/include/configs/x86-common.h b/include/configs/x86-common.h
index 4b39faababd..486b5ca7765 100644
--- a/include/configs/x86-common.h
+++ b/include/configs/x86-common.h
@@ -44,10 +44,6 @@
 	"ext2load scsi 0:3 01000000 /boot/vmlinuz; zboot 01000000"
 #endif
 
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE			115200
-#endif
-
 /*
  * Miscellaneous configurable options
  */
diff --git a/include/configs/xtfpga.h b/include/configs/xtfpga.h
index b69834a7fa1..ccc90a66f7d 100644
--- a/include/configs/xtfpga.h
+++ b/include/configs/xtfpga.h
@@ -170,7 +170,6 @@
 
 /* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */
 #define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
 /*======================*/
 /* Ethernet Driver Info */
diff --git a/include/configs/zmx25.h b/include/configs/zmx25.h
deleted file mode 100644
index d7cbb0f7c98..00000000000
--- a/include/configs/zmx25.h
+++ /dev/null
@@ -1,78 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (c) 2011 Graf-Syteco, Matthias Weisser
- * <[email protected]>
- *
- * Configuation settings for the zmx25 board
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/imx-regs.h>
-
-#define CONFIG_SYS_TIMER_RATE		32768
-#define CONFIG_SYS_TIMER_COUNTER	\
-	(&((struct gpt_regs *)IMX_GPT1_BASE)->counter)
-
-/*
- * Environment settings
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"gs_fast_boot=setenv bootdelay 5\0" \
-	"gs_slow_boot=setenv bootdelay 10\0" \
-	"bootcmd=dcache off; mw.l 0x81000000 0 1024; usb start;" \
-		"fatls usb 0; fatload usb 0 0x81000000 zmx25-init.bin;" \
-		"bootm 0x81000000; bootelf 0x81000000\0"
-
-/*
- * Hardware drivers
- */
-
-/*
- * Serial
- */
-#define CONFIG_MXC_UART_BASE	UART2_BASE
-
-/*
- * Ethernet
- */
-#define CONFIG_FEC_MXC
-#define CONFIG_FEC_MXC_PHYADDR		0x00
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * USB
- */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI_MXC
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_MXC_USB_PORT	1
-#define CONFIG_MXC_USB_PORTSC	PORT_PTS_SERIAL
-#define CONFIG_MXC_USB_FLAGS	(MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN)
-#define CONFIG_EHCI_IS_TDI
-#endif /* CONFIG_CMD_USB */
-
-/* SDRAM */
-#define PHYS_SDRAM		0x80000000	/* start address of LPDDRRAM */
-#define PHYS_SDRAM_SIZE		0x04000000	/* 64 megs */
-
-#define CONFIG_SYS_SDRAM_BASE	PHYS_SDRAM
-#define CONFIG_SYS_INIT_SP_ADDR	0x78020000	/* end of internal SRAM */
-
-/*
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE		0xA0000000
-#define CONFIG_SYS_MAX_FLASH_BANKS	1
-#define CONFIG_SYS_MAX_FLASH_SECT	256
-
-/*
- * CFI FLASH driver setup
- */
-
-#endif	/* __CONFIG_H */