m68k: Remove astro_mcf5373l board

This board is currently unmaintained. Remove it.

Acked-by: Angelo Dureghello <[email protected]>
Signed-off-by: Tom Rini <[email protected]>

1 files changed, 0 insertions, 187 deletions

diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h
deleted file mode 100644
index 65224324fbc..00000000000
--- a/include/configs/astro_mcf5373l.h
+++ /dev/null
@@ -1,187 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Configuration settings for the Sentec Cobra Board.
- *
- * (C) Copyright 2003 Josef Baumgartner <[email protected]>
- */
-
-/*
- * configuration for ASTRO "Urmel" board.
- * Originating from Cobra5272 configuration, messed up by
- * Wolfgang Wegner <[email protected]>
- * Please do not bother the original author with bug reports
- * concerning this file.
- */
-
-#ifndef _CONFIG_ASTRO_MCF5373L_H
-#define _CONFIG_ASTRO_MCF5373L_H
-
-#include <linux/stringify.h>
-
-/*
- * set the card type to actually compile for; either of
- * the possibilities listed below has to be used!
- */
-#define ASTRO_V532	1
-
-#if ASTRO_V532
-#define ASTRO_ID	0xF8
-#elif ASTRO_V512
-#define ASTRO_ID	0xFA
-#elif ASTRO_TWIN7S2
-#define ASTRO_ID	0xF9
-#elif ASTRO_V912
-#define ASTRO_ID	0xFC
-#elif ASTRO_COFDMDUOS2
-#define ASTRO_ID	0xFB
-#else
-#error No card type defined!
-#endif
-
-/* I2C */
-
-/*
- * Defines processor clock - important for correct timings concerning serial
- * interface etc.
- */
-
-#define CFG_SYS_CLK			80000000
-#define CFG_SYS_CPU_CLK		(CFG_SYS_CLK * 3)
-#define CFG_SYS_SDRAM_SIZE		32		/* SDRAM size in MB */
-
-/*
- * Define baudrate for UART1 (console output, tftp, ...)
- * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
- * CFG_SYS_BAUDRATE_TABLE defines values that can be selected
- * in u-boot command interface
- */
-
-#define CFG_SYS_UART_PORT		(2)
-#define CFG_SYS_UART2_ALT3_GPIO
-
-/* here we put our FPGA configuration... */
-
-/* Define user parameters that have to be customized most likely */
-
-/* AUTOBOOT settings - booting images automatically by u-boot after power on */
-
-/*
- * The following settings will be contained in the environment block ; if you
- * want to use a neutral environment all those settings can be manually set in
- * u-boot: 'set' command
- */
-
-#define CFG_EXTRA_ENV_SETTINGS			\
-	"loaderversion=11\0"				\
-	"card_id="__stringify(ASTRO_ID)"\0"			\
-	"alterafile=0\0"				\
-	"xilinxfile=0\0"				\
-	"xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\
-		"fpga load 0 0x41000000 $filesize\0" \
-	"alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\
-		"fpga load 1 0x41000000 $filesize\0" \
-	"env_default=1\0"				\
-	"env_check=if test $env_default -eq 1;"\
-		" then setenv env_default 0;saveenv;fi\0"
-
-/*
- * "update" is a non-standard command that has to be supplied
- * by external update.c; This is not included in mainline because
- * it needs non-blocking CFI routines.
- */
-
-#define CFG_SYS_FPGA_WAIT		1000
-
-/* End of user parameters to be customized */
-
-/* Defines memory range for test */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/* Base register address */
-
-#define CFG_SYS_MBAR		0xFC000000	/* Register Base Addrs */
-
-/* System Conf. Reg. & System Protection Reg. */
-
-#define CFG_SYS_SCR		0x0003;
-#define CFG_SYS_SPR		0xffff;
-
-/*
- * Definitions for initial stack pointer and data area (in internal SRAM)
- */
-#define CFG_SYS_INIT_RAM_ADDR	0x80000000
-#define CFG_SYS_INIT_RAM_SIZE		0x8000
-#define CFG_SYS_INIT_RAM_CTRL	0x221
-
-/*
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * for MCF5373, the allowable range is 0x40000000 to 0x7FF00000
- */
-#define CFG_SYS_SDRAM_BASE		0x40000000
-
-/*
- * Chipselect bank definitions
- *
- * CS0 - Flash 32MB (first 16MB)
- * CS1 - Flash 32MB (second half)
- * CS2 - FPGA
- * CS3 - FPGA
- * CS4 - unused
- * CS5 - unused
- */
-#define CFG_SYS_CS0_BASE		0
-#define CFG_SYS_CS0_MASK		0x00ff0001
-#define CFG_SYS_CS0_CTRL		0x00001fc0
-
-#define CFG_SYS_CS1_BASE		0x01000000
-#define CFG_SYS_CS1_MASK		0x00ff0001
-#define CFG_SYS_CS1_CTRL		0x00001fc0
-
-#define CFG_SYS_CS2_BASE		0x20000000
-#define CFG_SYS_CS2_MASK		0x00ff0001
-#define CFG_SYS_CS2_CTRL		0x0000fec0
-
-#define CFG_SYS_CS3_BASE		0x21000000
-#define CFG_SYS_CS3_MASK		0x00ff0001
-#define CFG_SYS_CS3_CTRL		0x0000fec0
-
-#define CFG_SYS_FLASH_BASE		0x00000000
-
-/* Reserve 256 kB for Monitor */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization ??
- */
-#define CFG_SYS_BOOTMAPSZ		(CFG_SYS_SDRAM_BASE + \
-						(CFG_SYS_SDRAM_SIZE << 20))
-
-/* FLASH organization */
-
-#define CFG_SYS_FLASH_SIZE		0x2000000
-
-#define LDS_BOARD_TEXT \
-	. = DEFINED(env_offset) ? env_offset : .; \
-	env/embedded.o(.text*)
-
-/* Cache Configuration */
-
-#define ICACHE_STATUS			(CFG_SYS_INIT_RAM_ADDR + \
-					 CFG_SYS_INIT_RAM_SIZE - 8)
-#define DCACHE_STATUS			(CFG_SYS_INIT_RAM_ADDR + \
-					 CFG_SYS_INIT_RAM_SIZE - 4)
-#define CFG_SYS_ICACHE_INV		(CF_CACR_CINVA)
-#define CFG_SYS_CACHE_ACR0		(CFG_SYS_SDRAM_BASE | \
-					 CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \
-					 CF_ACR_EN | CF_ACR_SM_ALL)
-#define CFG_SYS_CACHE_ICACR		(CF_CACR_EC | CF_CACR_CINVA | \
-					 CF_CACR_DCM_P)
-
-#endif	/* _CONFIG_ASTRO_MCF5373L_H */