summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-03-30configs: ls1088aqds: support distro bootBiwen Li
Add support of distro boot for ls1088aqds Signed-off-by: Biwen Li <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30board: fsl: lx2160a: fix SDHC1_DAT4 signal routingYangbo Lu
The SDHC1_DAT4 signal could be routes to SDHC1_VS or SDHC1 adapter slot for SDHC1 usage. When SDHC1 is selected in RCW, do not force to route it to SDHC1 adapter slot if find it has already been configued for SDHC1_VS. Signed-off-by: Yangbo Lu <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30pci-host-ecam-generic: access config space independent of system-wide bus idVladimir Oltean
The pci-host-ecam-generic code assumes that the ECAM is the first PCI bus in the system to be probed. Therefore, the system-wide bus number allocated by U-Boot in sequence for it is going to be zero, which corresponds to the memory-mapped config spaces found within it. Reuse the logic from other PCI bus drivers, and assume that U-Boot will allocate bus numbers in sequence for all buses within the current ECAM. So the base number of the bus needs to be subtracted when indexing the correct config space. Fixes: 3675cb044e68 ("PCI: Add driver for a 'pci-host-ecam-generic' host controller") Signed-off-by: Vladimir Oltean <[email protected]> Reviewed-by: Alex Marginean <[email protected]> Signed-off-by: Priyanka Jain <[email protected]>
2020-03-30include/configs: ls1012afrwy: fix load address of itb with bootm commandBiwen Li
The old load address of itb will overwrite uboots reserved memory on ls1012afrwy with 512 MiB ram Signed-off-by: Biwen Li <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30armv8/ls1046ardb: RGMII ports require internal delayMadalin Bucur
The correct setting for the RGMII ports on LS1046ARDB is to enable delay on both Rx and Tx so the interface mode used must be PHY_INTERFACE_MODE_RGMII_ID. There is a pull-up that turns on Rx internal delay by default and the u-boot does not override that (yet) so in u-boot the interface is functional. In Linux the PHY driver is clearing the Rx delay for the "rgmii-txid" mode and the reception does not work. Changing the RGMII mode to internal delay here ensures that device tree fix-ups for the PHY connection type turn on both Tx and Rx internal delay in Linux. Fixes: cc1aa218f510 ("armv8/ls1046a: RGMII PHY requires internal delay on Tx") Signed-off-by: Madalin Bucur <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30armv8/ls1043ardb: RGMII ports require internal delayMadalin Bucur
The correct setting for the RGMII ports on LS1043ARDB is to enable delay on both Rx and Tx so the interface mode used must be PHY_INTERFACE_MODE_RGMII_ID. There is a pull-up that turns on Rx internal delay by default and the u-boot does not override that (yet) so in u-boot the interface is functional. In Linux the PHY driver is clearing the Rx delay for the "rgmii-txid" mode and the reception does not work. Changing the RGMII mode to internal delay here ensures that device tree fix-ups for the PHY connection type turn on both Tx and Rx internal delay in Linux. Fixes: 5a78a472f666 ("armv8/ls1043a: RGMII PHY requires internal delay on Tx") Signed-off-by: Madalin Bucur <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30net: fman: add support for all RGMII delay modesMadalin Bucur
The RGMII modes that include internal delay were not all properly treated in the memac code. Add support for all RGMII delay modes. Fixes: 111fd19e3b9e ("fm/mEMAC: add mEMAC frame work") Signed-off-by: Madalin Bucur <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30lx2160a: Add dhcp in boot_targetsMeenakshi Aggarwal
Add dhcp in supported boot_targets for lx2160. Signed-off-by: Meenakshi Aggarwal <[email protected]> Signed-off-by: Priyanka Jain <[email protected]>
2020-03-30armv8: ls1028a: add dhcp boot target deviceYuantian Tang
Add DHCP boot target device to enable command bootcmd_dhcp. Signed-off-by: Yuantian Tang <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30board: ls1028ardb: add BOARD_LATE_INIT configYuantian Tang
Select BOARD_LATE_INIT config so that many board works can be done in late init stage. Signed-off-by: Yuantian Tang <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30lx2160a : Remove default VID settingMeenakshi Aggarwal
Set VID to 800 mV for Rev1 and set VID as per switch settings for Rev2. Signed-off-by: Meenakshi Aggarwal <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30armv8: ls1028a: Update secure boot headers offsetPriyanka Singh
Update the secure boot headers offsets of Kernel and other firmware images for SD and XSPI boot sources used by esbc_validate command. Signed-off-by: Priyanka Singh <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30lx2160a : Add emmc in boot_targets environment variableMeenakshi Aggarwal
Add emmc in supported boot_targets and Add bootcmd environment variable for emmc boot. Signed-off-by: Meenakshi Aggarwal <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30arm64: ls1046a: remove fdt_high environment variableYuantian Tang
Setting fdt_high and initrd_high to 0xffffffffffffffff leads to various difficulty to resolve bugs. Remove them and use bootm_size instead to safely contain a kernel, device tree and initrd for relocation. Signed-off-by: Yuantian Tang <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30arm64: ls1028a: remove fdt_high environment variableYuantian Tang
Setting fdt_high and initrd_high to 0xffffffffffffffff leads to various difficulty to resolve bugs. Remove them and use bootm_size instead to safely contain a kernel, device tree and initrd for relocation. Signed-off-by: Yuantian Tang <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30board: fsl: lx2160a: Add GIC LPI memory reserve fixupWasim Khan
Reserve DDR memory region used for GIC LPI configuration table. Signed-off-by: Wasim Khan <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30configs: lx2160a: Enable GIC_V3_ITS configWasim Khan
Enable GIC_V3_ITS config to program GIC LPI configuration table. Signed-off-by: Wasim Khan <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30board: fsl: lx2160a: Program GIC LPI configuration tableWasim Khan
Program GIC LPI configuration table: 1. Redistributor PROCBASER configuration table (which is common for all redistributors) 2. Redistributor pending table (PENDBASER), for all the available redistributors. Signed-off-by: Manish Tomar <[email protected]> Signed-off-by: Wasim Khan <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30board: lx2160a: Correct board fixup for PCIe nodesVikas Singh
Update "board_fix_fdt" with correct counter value "i". This will fix the issue while fetching the "reg_names" resource from fdt after fixup. Signed-off-by: Vikas Singh <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30ls1021a: Set CONFIG_SYS_BOOTMAPSZ to the memory for relocationAlison Wang
This patch sets CONFIG_SYS_BOOTMAPSZ to the amount of memory available to safely contain a kernel, device tree and initrd for relocation. The way to set fdt_high as 0xffffffff to disable device tree relocation is removed. Signed-off-by: Alison Wang <[email protected]> Reviewed-by: Tom Rini <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-03-30ARM: dts: rmobile: Enable IIC3 on V2H BlancheMarek Vasut
Enable IIC3 to permit access to the PMIC. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2020-03-30ARM: dts: rmobile: Add IIC3 node on Gen2 R8A7792 V2HMarek Vasut
Add IIC3 node from mainline Linux DT. This will be further updated in subsequent DT sync, however adding this node for now is sufficient and minimal change. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2020-03-30clk: renesas: Switch to fdtdec_get_addr_size_auto_noparent() on Gen2Marek Vasut
The fdtdec_get_addr() does not take into account values set in #address-cells and #size-cells , but assumes them to be 1 for 32bit systems and 2 for 64bit systems. This is true for most DTs, however there are exceptions. Switch to fdtdec_get_addr_size_auto_noparent(), which takes the #address/size-cells values into consideration, otherwise the reset controller node register offset is incorrectly parsed. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2020-03-30ARM: rmobile: Convert Gen2 Blanche to DM_SPI{,_FLASH}Marek Vasut
Enable DM_SPI and DM_SPI_FLASH in U-Boot on V2H Blanche. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2020-03-30usb: Migrate to support live DT for some driverKever Yang
Use ofnode_ instead of fdt_ APIs so that the drivers can support live DT. This patch updates usb_get_dr_mode() and usb_get_maximum_speed() to use ofnode as parameter instead of fdt offset. And all the drivers who use these APIs update to use live dt APIs at the same time. Signed-off-by: Kever Yang <[email protected]>
2020-03-30usb: ehci-msm: Use dev interface to get device addressKever Yang
Use dev_read_addr_ptr() instead of devfdt_get_addr() so that we can support live DT. Signed-off-by: Kever Yang <[email protected]> Reviewed-by: Ramon Fried <[email protected]>
2020-03-30usb: dwc3-of-simple: Drop redundant inclding header fileKever Yang
The fdtdec.h is no use in this file, remove the include code. Signed-off-by: Kever Yang <[email protected]>
2020-03-28configs: a64-olinuxino-emmc: add eMMC boot part config commandsPetr Štetiar
mmc bootbus and partconf commands are needed in order to be able to configure booting from separate boot0/boot1 eMMC partitions. Signed-off-by: Petr Štetiar <[email protected]> [jagan: rebase on master] Signed-off-by: Jagan Teki <[email protected]>
2020-03-28vexpress_ca9x4: Enable use of correct DTB file and restore EFI loader.Kristian Amlie
EFI was disabled in f95b8a4b5f64f because of the missing DTB file, and indeed, the DTB file is required to load recent versions of GRUB (2.04) correctly. Signed-off-by: Kristian Amlie <[email protected]>
2020-03-28efi_loader: only reserve memory if fdt node enabledHeinrich Schuchardt
Sub-nodes of /reserved-memory may be disabled. In this case we should not reserve memory in the memory map. Reported-by: Patrick DELAUNAY <[email protected]> Fixes: fef907b2e440 ("efi_loader: create reservations after ft_board_setup") Signed-off-by: Heinrich Schuchardt <[email protected]> Reviewed-by: Atish Patra <[email protected]>
2020-03-28cmd: efidebug: fix int to pointer castHeinrich Schuchardt
On 32 bit systems fix warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] Fixes: a415d61eac26 ("cmd: map addresses to sysmem in efidebug memmap") Signed-off-by: Heinrich Schuchardt <[email protected]>
2020-03-28test/py: UEFI helloworld requires OF_CONTROLHeinrich Schuchardt
With CONFIG_OF_CONTROL environment variable $fdtcontroladdr is not defined and test_efi_helloworld_net() fails. Signed-off-by: Heinrich Schuchardt <[email protected]>
2020-03-27Merge branch '2020-03-27-master-imports'Tom Rini
- Update a few MAINTAINERS entries - cache alignment fix in ext4 code - Two small test fixes
2020-03-27test: typo decompressionHeinrich Schuchardt
%s/decopmression/decompression/ Signed-off-by: Heinrich Schuchardt <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2020-03-27MAINTAINERS: add myself as maintainer of fs/btrfsMarek Behún
Signed-off-by: Marek Behún <[email protected]>
2020-03-27fs: ext4: Fix alignment of cache buffersJan Kiszka
We need to align the cache buffer to ARCH_DMA_MINALIGN in order to avoid access errors like CACHE: Misaligned operation at range [be0231e0, be0235e0] seen on the MCIMX7SABRE. Fixes: d5aee659f217 ("fs: ext4: cache extent data") Signed-off-by: Jan Kiszka <[email protected]> Reviewed-by: Tom Rini <[email protected]> Reviewed-by: Stephen Warren <[email protected]> Tested-by: Peter Robinson <[email protected]>
2020-03-27MAINTAINERS: Add usb.h entry to usbMarek Vasut
Add usb.h file into the USB list. Signed-off-by: Marek Vasut <[email protected]> Cc: Tom Rini <[email protected]>
2020-03-27test/py: mmc: Fix 'mmc info' testcaseHarald Seiler
Commit 41e30dcf8796 ("cmd: mmc: Make Mode: printout consistent") fixed the layout of `mmc info` output. Reflect this change in the respective testcase. Also fix a typo in the documentation. Fixes: 41e30dcf8796 ("cmd: mmc: Make Mode: printout consistent") Signed-off-by: Harald Seiler <[email protected]> Acked-by: Stephen Warren <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2020-03-27Revert "vexpress_ca9x4: Enable use of correct DTB file and restore EFI loader."Tom Rini
Currently this causes failures of the platform when running the EFI loader tests, so disable it for now. This reverts commit af827140e5965e5bb2bcad1c53ca8419b428ff6d. Signed-off-by: Tom Rini <[email protected]>
2020-03-26Merge tag 'u-boot-rockchip-20200327' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Fixed for rv1108 and elgin-rv1108 board - Fix the keyboard from USB instead of CrOS EC
2020-03-26Merge tag 'u-boot-stm32-20200324' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm into next - stm32mp: fix command stboard - stm32mp: update kernel device tree according the part number - stm32mp: add 800 MHz profile support = stm32mp15xd and stm32mp15xf - stm32mp: set cp15 frequency in psci cpu on - stm32mp: DT alignment with Linux 5.6-rc1 - stm32mp: clk: add SPI5 support and correct CKSELR masks - stm32mp: ram: fixes on LPDDR2/LPDDR3 support and on tuning - stm32: i2c: allows for any bus frequency - sti: timer: livetree and clk API conversion
2020-03-26rockchip: mkimage: Use an existing macro instead of a decimal valueMiquel Raynal
Depending on the SoC, a header of four characters is prepended to the image. There is already a macro defining the number of characters: RK_SPL_HDR_SIZE, so use it instead of hardcoding "4". Signed-off-by: Miquel Raynal <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-03-26rv1108: Fix boot regressionOtavio Salvador
Since commit 79030a486128 ("rockchip: Add Single boot image (with binman, pad_cat)") the following boot regression is seen: U-Boot 2020.04-rc3-00050-gd16e18ca6c-dirty (Mar 09 2020 - 11:40:07 -0300) Model: Elgin RV1108 R1 board DRAM: 128 MiB initcall sequence 67fd12a0 failed at call 6000b927 (err=-22) This happens because the above commit missed to include the "rockchip-u-boot.dtsi" for rv1108, so include this file like it done for other Rockchip SoC dtsi's. Fixes: 79030a486128 ("rockchip: Add Single boot image (with binman, pad_cat)") Signed-off-by: Otavio Salvador <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-03-26elgin-rv1108: Avoid adc_channel_single_shot errorOtavio Salvador
Currently the following error message is seen during boot: U-Boot 2020.01-08751-g55759ae141 (Mar 09 2020 - 14:44:52 -0300) Model: Elgin RV1108 R1 board DRAM: 128 MiB APLL: 600000000 DPLL:1200000000 GPLL:1188000000 ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000 MMC: dwmmc@30110000: 0 Loading Environment from MMC... OK In: serial@10210000 Out: serial@10210000 Err: serial@10210000 Model: Elgin RV1108 R1 board rockchip_dnl_key_pressed: adc_channel_single_shot fail! .... Since the elgin-rv1108 does not use ADC to read the download key status, select CONFIG_ROCKCHIP_BOOT_MODE_REG=0 to avoid such error. Signed-off-by: Otavio Salvador <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-03-26elgin-rv1108: Use rk_board_late_init() for GPIO settingsOtavio Salvador
Since commit 8e9a8d0d0c8c ("rockchip: elgin-rv1108: use board_early_init_f for per-boar init") the function that configure the board GPIOs is no longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected. These GPIOs do not need to be configured in such early stagem, so change it to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y to fix the regression. Signed-off-by: Otavio Salvador <[email protected]> Signed-off-by: Fabio Berton <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-03-26ARM: dts: Activate pullups in the console pins on rv1108-elgin-r1Otavio Salvador
In order to make the console pins more robust to noise, activate the pullups and increase its drive strength. Signed-off-by: Otavio Salvador <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-03-26rockchip: Change keyboard input from CrOS EC keyboard to a USB keyboardPeter Robinson
These boards aren't ChromeOS devices so won't have a cros-ec-keyb input as it's the keyboard available via the ChromeOS Embedded Controller. Update them to use a USB keyboard which would actually be available. Also enable the usb keyboard option for those devices that don't have it enabled already. Signed-off-by: Peter Robinson <[email protected]> Reviewed-by: Michael Trimarchi <[email protected]> Reviewed-by: Simon Glass <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-03-26rockchip: evb-rv1108: Use syscon API to get grf baseKever Yang
Use syscon API to get grf base instead of get from dts. Signed-off-by: Kever Yang <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2020-03-26rockchip: elgin-rv1108: Use syscon API to get grf baseKever Yang
Use syscon API to get grf base instead of get from dts. Signed-off-by: Kever Yang <[email protected]> Reviewed-by: Simon Glass <[email protected]> Acked-by: Otavio Salvador <[email protected]>
2020-03-24timer: sti: use clk API to get timer clock rateNicolas Heemeryck
Retrieve clock rate through device tree. This mimics the behavior of arm_global_timer in Linux. Signed-off-by: Nicolas Heemeryck <[email protected]> Cc: Patrice Chotard <[email protected]> Acked-by: Patrice Chotard <[email protected]>
generated by cgit v1.3.1 (git 2.54.0) at 2026-08-13 05:02:18 +0000