| Age | Commit message (Collapse) | Author |
|---|
|
According to SD and MMC spec, 74 clocks must be sent to device after
power stable. This is need in reinit ops for DM MMC or init ops for
non-DM MMC after power cycle.
So set the INTIA to send 80 clocks in esdhc_init_common and move
its calling from probe to reinit.
However, on 8MQ EVK and 8QXP MEK with some brands of SD cards, sending
80 clocks may not work well.
The root cause is related with power up time. According to spec, after
power stable, host shall supply at least 74 SD clocks to the SD card with
the maximum of 1ms. However, the power ram up time is related with the
characteristic of SD card. At the moment of sending 74 SD clocks, the
power probably not ram up to the operating level on the problematic
cards. Then cause the cards not ready.
This patch changes to send SD clock with 1ms duration to replace 80
SD clocks (0.2ms at 400Khz clock).
This way meets the spec requirement as well, and adds the margin for
power ram up time to be compatible with the problematic SD cards.
This is also aligned with implementation which has FORCE clock
always on.
Reviewed-and-tested-by: Haibo Chen <[email protected]>
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
With partition reset supported for i.MX8QM/QXP/95 and etc, when linux
mmc runtime suspended, the mmc clks are gated off. While at same time
system controller reset Cortex-A cores because of various reasons(
WDOG timeout and etc), with SPL run again, only enable PER clk is not
enough, also need to enable AHB/IPG clk, here use clk bulk API to enable
all the clocks.
Signed-off-by: Peng Fan <[email protected]>
|
|
So we can disable to build ADP5585 in SPL to save size
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Add support for DH electronics i.MX8MP DHCOM SoM on DRC02 carrier board.
This system is populated with two ethernet ports, two CANs, RS485 and RS232,
USB, capacitive buttons and an OLED display.
Matching Linux kernel patch has been posted:
https://lore.kernel.org/imx/[email protected]/
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Add support for DH electronics i.MX8M Plus DHCOM SoM on PicoITX carrier board.
This system is populated with serial console, EQoS ethernet, eMMC, SD, SPI NOR,
LEDs and USB 3.0 host used in USB 2.0 mode on PicoITX.
Matching Linux kernel patch has been posted:
https://lore.kernel.org/imx/[email protected]/
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dfu into next
u-boot-dfu-next-20241003
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/22516
DFU:
- Reinitialize only if dfu_alt_info changed
USB Gadget:
- New usb gadget driver for Renesas USBHS
- Simplify kconfig deps for CMD_USB_MASS_STORAGE
Android:
- Provide bootloader version to android via kernel commandline
|
|
Simon Glass <[email protected]> says:
This includes various patches towards implementing the VBE abrec
bootmeth in U-Boot.
|
|
This driver should not generally be present in SPL, even if misc devices
are enabled. Update the Makefile rule accordingly.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a missing colon and newline in rk3399_emmc_get_phy().
Signed-off-by: Simon Glass <[email protected]>
|
|
Allow MMC init when clock support is not enabled in a particular phase.
Refactor the setting of priv->emmc_clk so it is a bit clearer.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a little logging to some places in this driver, to aid debugging
when something goes wrong.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add an error-return log to the call in mmc_init_device()
Signed-off-by: Simon Glass <[email protected]>
|
|
When MMC booting fails it is sometimes hard to figure out what went
wrong as there is no error code. It isn't even clear which MMC device
was chosen, since SPL can have its own numbering.
Add some debugging to help with this.
Signed-off-by: Simon Glass <[email protected]>
|
|
Some boards want to use DM_MMC in TPL so add an option for that.
Signed-off-by: Simon Glass <[email protected]>
|
|
There are currently four symbols here, so drop the word 'two'.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
This header includes more than just dummy functions, so drop this
comment.
Signed-off-by: Simon Glass <[email protected]>
|
|
Separate BSS is current mandatory on armv8 but this is not useful for
early boot phases. Add support for the combined BSS.
Use an #ifdef to avoid using CONFIG_SPL_BSS_START_ADDR which is not
valid in this case.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
Some boards want to use the debug UART in TPL so add an option for that.
Signed-off-by: Simon Glass <[email protected]>
|
|
Some boards want to use RAM in VPL so add an option for that.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add an option so that this feature can be enabled in TPL for boards
which need it.
Signed-off-by: Simon Glass <[email protected]>
|
|
The sprintf() etc. functions are supposed to return the length of the
string written, but do not. Fix this by checking the amount of buffer
space used.
Signed-off-by: Simon Glass <[email protected]>
|
|
Adjust the condition so that separate BSS can be deselected for TPL and
VPL.
Signed-off-by: Simon Glass <[email protected]>
|
|
This doesn't describe the length parameter correctly. Fix it and
zunzip() too.
Signed-off-by: Simon Glass <[email protected]>
|
|
When bootstd is not enabled, bootdevs should not be set up. Add a
static inline function to see to this.
Signed-off-by: Simon Glass <[email protected]>
|
|
This file uses __aligned so should include the header which defines
that.
Signed-off-by: Simon Glass <[email protected]>
|
|
Before
commit da3447d09fa0 ("android: Fix ramdisk loading for bootimage v3+"),
the ramdisk was loaded from img_data.ramdisk_ptr, ignoring offset
provided via mkbootimg.
commit da3447d09fa0 ("android: Fix ramdisk loading for bootimage v3+")
rightfully fixes this by switching to use img_data.ramdisk_addr instead.
However, it does not copy the ramdisk content to img_data.ramdisk_addr
in case we use boot image v2.
Because of this, we can no longer boot Android on Khadas vim3 board:
[ 3.940361] RAMDISK: Couldn't find valid RAM disk image starting at 0.
Add the missing memcpy() to fix the issue.
Fixes: da3447d09fa0 ("android: Fix ramdisk loading for bootimage v3+")
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
Oliver Gaskell <[email protected]> says:
ADSP-SC5xx is a series of ARM-based DSPs.
This comprises the armv7 based SC57x, SC58x and SC594 series, and the
armv8 based SC598.
This patch series includes configurations, init code, and minimal DTs
to enable Analog Devices' evaluation boards for these SoCs to boot
through SPL and into U-Boot Proper, as well as devicetree schemas for
the added DTs.
This patch series depends on ("arm: Add Analog Devices SC5xx Machine
Type") (https://lists.denx.de/pipermail/u-boot/2024-April/552043.html)
|
|
Adds support for Analog Devices' SC573-EZKIT board. Includes:
- SoC specific configs in mach-sc5xx/Kconfig
- Memory Map for SPL
- Necessary board-specific init functions
- Board-specific Kconfig and environment in board/adi/
- Memory configuration
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Adds support for Analog Devices' SC589-MINI board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Adds support for Analog Devices' SC589-EZKIT board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
- Memory configuration
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Adds support for Analog Devices' SC584-EZKIT board. Includes:
- SoC specific configs in mach-sc5xx/Kconfig
- Memory Map for SPL
- SPL config options in common/spl/Kconfig
- Necessary board-specific init functions
- Board-specific Kconfig and environment in board/adi/
- Memory configuration
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Trevor Woerner <[email protected]>
Signed-off-by: Trevor Woerner <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Adds support for Analog Devices' SC594-SOM-EZLITE board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Adds support for Analog Devices' SC594-SOM-EZKIT board. Includes:
- SoC specific configs in mach-sc5xx/Kconfig
- Memory Map for SPL
- SPL config options in common/spl/Kconfig
- Necessary board-specific init functions
- Board-specific Kconfig and environment in board/adi/
- Memory configuration
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Trevor Woerner <[email protected]>
Signed-off-by: Trevor Woerner <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Co-developed-by: Ian Roberts <[email protected]>
Signed-off-by: Ian Roberts <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Adds support for Analog Devices' SC598-SOM-EZLITE board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Adds support for Analog Devices' SC598-SOM-EZKIT board. Includes:
- CONFIG options common to all SC5xx SoCs
- SoC specific configs in mach-sc5xx/Kconfig
- SPL config options in common/spl/Kconfig
- Memory Map for SPL
- Necessary board-specific init functions
- Board-specific Kconfig and environment in board/adi/
- Memory configuration
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Co-developed-by: Trevor Woerner <[email protected]>
Signed-off-by: Trevor Woerner <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Moves common options between all SC5xx series boards to the ARCH_SC5XX
option instead of duplicating them.
Also, it was possible to select multiple of the SoC support options.
Given a U-Boot binary can only support a single platform, this moves
the SoC selection to a `choice`, making them mutually exclusive.
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Add devicetree schema for the timer peripheral on Analog Devices SC5xx
series SoCs.
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Add devicetree schema for the clock tree on Analog Devices SC5xx series
SoCs.
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Add devicetree schema for Analog Devices SC5xx series SoCs.
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Add minimal device tree for Analog Devices' SC598-SOM-EZLITE board.
This patch depends on Patches 01 and 07, for sc5xx.dtsi and
sc598-som.dtsi respectively.
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Add minimal device tree for Analog Devices' SC598-SOM-EZKIT board, and
the SC598 SoM.
This patch depends on patch 01, for sc5xx.dtsi.
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Add minimal device tree for Analog Devices' SC594-SOM-EZLITE board.
This patch depends on Patches 01 and 05, for sc5xx.dtsi and
sc594-som.dtsi respectively.
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Add minimal device tree for Analog Devices' SC594-SOM-EZKIT board, and
the SC594 SoM.
This patch depends on patch 01, for sc5xx.dtsi.
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Add minimal device tree for Analog Devices' SC589-EZKIT board.
This patch depends on Patches 01 and 02, for sc5xx.dtsi and sc58x.dtsi.
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Trevor Woerner <[email protected]>
Signed-off-by: Trevor Woerner <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Add minimal device tree for Analog Devices' SC589-MINI board.
This patch depends on Patches 01 and 02, for sc5xx.dtsi and sc58x.dtsi.
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Trevor Woerner <[email protected]>
Signed-off-by: Trevor Woerner <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Add minimal device tree for Analog Devices' SC584-EZKIT board, and
common files for the SC58x family.
This patch depends on Patch 01, for sc5xx.dtsi.
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Trevor Woerner <[email protected]>
Signed-off-by: Trevor Woerner <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
Adds minimal device tree for Analog Devices' SC573-EZKIT board and
common files for the SC57x/SC5xx family.
This also adds all sc5* devicetrees to ARM SC5XX in MAINTAINERS, and
adds the ADSP Linux mailing list as the list for ARM SC5XX.
Co-developed-by: Greg Malysa <[email protected]>
Signed-off-by: Greg Malysa <[email protected]>
Co-developed-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Nathan Barrett-Morrison <[email protected]>
Signed-off-by: Oliver Gaskell <[email protected]>
|
|
The primary upstream URL for tf-a has moved, in some cases
things like tags are not always pushed to the old URL so
update the URLs to the primary upstream project URL.
Signed-off-by: Peter Robinson <[email protected]>
|
|
CONFIG_USB_GADGET_DOWNLOAD depends on CONFIG_USB_GADGET.
It is sufficient to depend on the prior.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
This commit adds support to manage an external regulator to enable the main
power supply VDD.
Signed-off-by: Arturo Buzarra <[email protected]>
|
