| Age | Commit message (Collapse) | Author |
|---|
|
The devicetree binding files are in their own directory and use a simple
text format. Add a link for the binding for the /config node, since it
is otherwise hard to find.
Suggested-by: Heinrich Schuchardt <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Since Albert Aribaud is not maintaining anymore the LaCie Ethernet Disk
mini V2 board, then I am taking over.
Signed-off-by: Simon Guinot <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc153 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc153 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
I am taking over responsibility for the GE board from Sebastian Reichel.
Updating the MAINTAINERS files to reflect this.
Signed-off-by: Martyn Welch <[email protected]>
Acked-by: Sebastian Reichel <[email protected]>
|
|
As the lastest spear directories are removed, delete the associated entry
in the MAINTAINERS file:
- arch/arm/cpu/arm926ejs/spear/
- arch/arm/include/asm/arch-spear/
Fixes: 570c3dcfc153 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Output like the following is quite irritating:
=> bootefi hello
Scanning disk mmc2.blk...
No valid Btrfs found
Bad magic number for SquashFS image.
** Unrecognized filesystem type **
Scanning disk mmc1.blk...
No valid Btrfs found
Bad magic number for SquashFS image.
** Unrecognized filesystem type **
Scanning disk mmc0.blk...
No valid Btrfs found
Bad magic number for SquashFS image.
** Unrecognized filesystem type **
Albeit a whole disk may be formatted with a filesystem in most cases
a partition table is used and the whole disk (partition number 0) doesn't
contain a filesytem. Some partitions may only contain a blob. Not seeing a
filesytem on the whole disk or on any partition is only worth a debug
message.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Our mailmapper script required Python 2 which is no longer maintained.
A main difference when converting to Python 3 is that byte strings are not
character strings. So add conversion and skip over conversion errors.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Tpm test cases relies on tpm device setup. Provide an environment
variable "env__tpm_device_test_skip = True" to skip the test case
if tpm device is not present.
Only needed will have to add variable to the py-test framework.
Test runs successfully even this variable is absent.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
The KBUILD_BASENAME contains just the name of the compiled module,
in this case 'sequencer', rather than a full path to the compiled
file. Use it to prevent pulling the full path into the U-Boot binary,
which is useless and annoying.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Siew Chin Lim <[email protected]>
Cc: Simon Goldschmidt <[email protected]>
Cc: Tien Fong Chee <[email protected]>
|
|
The DM DWMAC driver is perfectly capable of configuring the ethernet
PHY reset GPIO, let the driver do it instead of doing it in the board
file.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Siew Chin Lim <[email protected]>
Cc: Simon Goldschmidt <[email protected]>
Cc: Tien Fong Chee <[email protected]>
|
|
The Designware I2C IP is used to communicate with I2C peripherals on
SoCFPGA, and required to access I2C EEPROM on this board. Enable it.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Siew Chin Lim <[email protected]>
Cc: Simon Goldschmidt <[email protected]>
Cc: Tien Fong Chee <[email protected]>
|
|
The USB peripheral controller is the DWC2 controller 1, not 0.
Update the phandle to fix UDC support on this board.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Siew Chin Lim <[email protected]>
Cc: Simon Goldschmidt <[email protected]>
Cc: Tien Fong Chee <[email protected]>
|
|
The WDT on this system should be enabled, make it so.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Siew Chin Lim <[email protected]>
Cc: Simon Goldschmidt <[email protected]>
Cc: Tien Fong Chee <[email protected]>
|
|
The SPI NOR bus mode is 0 on this system, update it accordingly.
Increase frequency to 40 MHz and enable SFDP parsing, since the
flashes on this system support that and it is a huge performance
improvement.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Siew Chin Lim <[email protected]>
Cc: Simon Goldschmidt <[email protected]>
Cc: Tien Fong Chee <[email protected]>
|
|
This was configured in downstream, so it is likely that most of the
custom software used around the device depends on it. Make upstream
compatible.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Siew Chin Lim <[email protected]>
Cc: Simon Goldschmidt <[email protected]>
Cc: Tien Fong Chee <[email protected]>
|
|
Increase the environment size from 4k to 16k to prevent
environment from becoming full.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Siew Chin Lim <[email protected]>
Cc: Simon Goldschmidt <[email protected]>
Cc: Tien Fong Chee <[email protected]>
|
|
The comment is no longer meaningful due to DT conversion, drop it.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Siew Chin Lim <[email protected]>
Cc: Simon Goldschmidt <[email protected]>
Cc: Tien Fong Chee <[email protected]>
|
|
This adds support for the DWC_sub31 controllers such as those
found on Apple's M1 SoC. This version of the controller
seems to work fine with the existing driver.
Signed-off-by: Mark Kettenis <[email protected]>
|
|
Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.
This also adds support for the HSIC mode of the i.MX7.
Signed-off-by: Markus Niebel <[email protected]>
Signed-off-by: Matthias Schiffer <[email protected]>
|
|
These definitions are unused, all boards that define portsc flags use
the equivalent PORT_* definitions instead.
Signed-off-by: Markus Niebel <[email protected]>
Signed-off-by: Matthias Schiffer <[email protected]>
|
|
The MXC_EHCI_MODE_ definitions are redundant. Replace MXC_EHCI_MODE_SERIAL
with the equivalent PORT_PTS_SERIAL.
Only the zmx25 platform is affected.
Signed-off-by: Markus Niebel <[email protected]>
Signed-off-by: Matthias Schiffer <[email protected]>
|
|
Import usb_phy_interface enum values and DT match strings from the Linux
kernel.
Signed-off-by: Markus Niebel <[email protected]>
Signed-off-by: Matthias Schiffer <[email protected]>
|
|
Pine H64 and Orange Pi 3 both provide a USB3 type A port.
Enable it in U-Boot.
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Some platforms, like the Allwinner H6, do not have a separate glue layer
around the dwc3. Instead, they rely on the clocks/resets/phys referenced
from the dwc3 DT node itself. Add support for enabling the clocks/resets
referenced from the dwc3 DT node.
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.
The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.
This also fixes a failure to call reset_free if xhci_register failed.
Fixes: 0b80371b350e ("usb: xhci: Add reset controller support")
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
This driver is needed for XHCI to work on the Allwinner H6 SoC. The
driver is copied from Linux v5.10.
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
On Intel Tangier the SDHCI #2 provides SD card connection.
Add GPIO card detection for it.
Fixes: 39665beed6f7 ("x86: tangier: Enable ACPI support for Intel Tangier")
BugLink: https://github.com/edison-fw/meta-intel-edison/issues/135
Signed-off-by: Andy Shevchenko <[email protected]>
Acked-by: Bin Meng <[email protected]>
|
|
eMMC is non-removable on Intel Edison board. Fix the DTS accordingly.
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated,
CONFIG_SYS_MAX_FLASH_BANKS is replaced by cfi_flash_num_flash_banks,
but this variable is defined in drivers/mtd/cfi_flash.c, which is
compiled only when CONFIG_FLASH_CFI_DRIVER is activated, in U-Boot
or in SPL when CONFIG_SPL_MTD_SUPPORT is activated.
This patch deactivates this feature CONFIG_SYS_MAX_FLASH_BANKS_DETECT
when flash cfi driver is not activated to avoid compilation issue in
the next patch, when CONFIG_SYS_MAX_FLASH_BANKS is used in spi_nor_scan().
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <[email protected]>
|
|
The controller may need to have clocks/resets enabled for it to work.
Add support for this. Since the clocks/resets are optional on some
platforms (per the device tree binding), do not prevent probing the
controller if they are missing.
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
The Linux i2c driver supports i2c-scl-rising-time-ns,
and i2c-scl-falling-time-ns, but U-Boot uses hard-coded values
for these values.
Update the calculation by fetching them from the device tree if
present and use the previous values as the default if they are
missing.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
Move the individual keystone 2 SoC symbols to the mach Kconfig file,
select them as needed.
Signed-off-by: Tom Rini <[email protected]>
|
|
We have individual SOC symbols for each keystone 2 platform. Use the
existing CONFIG_ARCH_KEYSTONE rather than CONFIG_SOC_KEYSTONE to
encompass all of the keystone families.
Signed-off-by: Tom Rini <[email protected]>
|
|
Clean up the config header file by removing some now irrelevant code /
comments.
Signed-off-by: Tom Rini <[email protected]>
|
|
Clean up the config header file by removing some now irrelevant code /
comments.
Signed-off-by: Tom Rini <[email protected]>
|
|
Clean up the config header file by removing some now irrelevant code /
comments.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
CONFIG_OMAP_EHCI_PHY3_RESET_GPIO
To do this, we also introduce CONFIG_HAS_CONFIG_OMAP_EHCI_PHYn_RESET_GPIO
options to get setting the GPIO number.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that DM_USB is always enabled, we can drop some legacy code.
Signed-off-by: Tom Rini <[email protected]>
|
|
We have one places that uses this symbol and CONFIG_TARGET_OMAPL138_LCDK
works equally well, switch to that.
Signed-off-by: Tom Rini <[email protected]>
|
|
Move the main option for handling drivers/dma/keystone_nav* to Kconfig,
and enable it by default. All of the sub-symbols are not configurable,
so remove them from the CONFIG namespace.
Signed-off-by: Tom Rini <[email protected]>
|
|
The COFNIG_KEYSTONE_RBL_NAND option is always enabled for the driver on
keystone platforms, but not older davinci platforms. Use def_bool for
the symbol. For CONFIG_KEYSTONE_NAND_MAX_RBL_PAGE, it's only used within
the driver and derived from another symbol, so remove CONFIG from the
name. Finally, CONFIG_KEYSTONE_NAND_MAX_RBL_SIZE is a bit more fixed.
For now, use the value directly. Long term, as part of DM'ifying NAND,
this should come from the device tree.
Signed-off-by: Tom Rini <[email protected]>
|
|
Since cm_t35 was removed, CONFIG_CM_T3X does not exist. This lets us
simplify the code in board/compulab/common/eeprom.c a bit.
Cc: Igor Grinberg <[email protected]>
Cc: Nikita Kiryanov <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_USB_XHCI_OMAP
Signed-off-by: Tom Rini <[email protected]>
|
|
At this point in time, all platforms that had previously used
drivers/usb/phy/omap_usb_phy.c have been migrated to DM and related
options. Remove this now unused code and some related unused defines.
Signed-off-by: Tom Rini <[email protected]>
|
|
This is only used in the aemif driver that is otherwise currently
keystone2 centric. Moving forward, if this is applicable to some other
platform then such base addresses should be able to be obtained via the
device tree. Use KS2_AEMIF_CNTRL_BASE directly now rather than
indirectly.
Signed-off-by: Tom Rini <[email protected]>
|
|
- At this point there are a large number of Beaglebone boards, refer to
them as a family rather than a growing list.
- Reword customization as we're largely Kconfig-oriented now.
- Remove the NOR section as the relevant defconfigs have long been
removed and the general support was not updated.
Signed-off-by: Tom Rini <[email protected]>
|
|
Convert the existing documentation to rST, keeping to just making
formatting changes to start with.
Signed-off-by: Tom Rini <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dm into next
Various of-platdata improvements, including CONFIG_OF_REAL
|
|
Prepare v2021.10-rc5
|
