| Age | Commit message (Collapse) | Author |
|---|
|
Our last sync with the kernel was 5.1.
We are so out of sync now, that tracking the patches and backporting
them one by one makes little sense and it's going to take ages.
This is an attempt to sync up Makefiles to 6.1.
Unfortunately due to sheer amount of patches this is not easy to review,
but that's what we decided during a community call for the bump to 5.1,
so we are following the same guidelines here.
Signed-off-by: Sughosh Ganu <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>a #rebased on -next
|
|
The MAINTAINERS files for B&R boards are not in sync
with the current file names. Update the files so
that they are correct again.
Signed-off-by: Wolfgang Wallner <[email protected]>
|
|
B&R Industrial Automation has been acquired by ABB in 2017, and this
will be reflected in our email addresses beginning from December 2025.
The email addresses change as follows:
@br-automation.com -> @<country-code>.abb.com
The existing email addresses will be valid until December 2026.
Add entries for Bernhard Messerklinger and myself to .mailmap, and
update the MAINTAINERS files.
Signed-off-by: Wolfgang Wallner <[email protected]>
Signed-off-by: Wolfgang Wallner <[email protected]>
|
|
Now that env_get_ip() has been removed, the include file <net.h> does
not need anything from <env.h>. Furthermore, include/env.h itself
includes other headers which can lead to longer indirect inclusion
paths. To prepare to remove <env.h> from <net.h> fix all of the
remaining places which had relied on this indirect inclusion to instead
include <env.h> directly.
Reviewed-by: Jerome Forissier <[email protected]> # net/lwip
Acked-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Wolfgang Wallner <[email protected]>
Reviewed-by: Martyn Welch <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
A number of platforms have "common" directories that are in turn not
listed by the board MAINTAINERS file. Add these directories in many
cases.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Since I'm leaving the company with end of June, the maintainership will
be transferred to Wolfgang Wallner.
Signed-off-by: Hannes Schmelzer <[email protected]>
Signed-off-by: Wolfgang Wallner <[email protected]>
|
|
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When binman is in use, most of the targets built by the Makefile are
inputs to binman. We then need a final rule to run binman to produce the
final outputs.
Rename the variable to indicate this, and add a new 'inputs' target.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <[email protected]>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <[email protected]>
|
|
Move this function out of common.h and into a relevant header file.
Signed-off-by: Simon Glass <[email protected]>
|
|
This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.
Signed-off-by: Hannes Schmelzer <[email protected]>
|
