| Age | Commit message (Collapse) | Author |
|---|
|
Remove DECLARE_GLOBAL_DATA_PTR from files where gd is not used, and
drop the unnecessary inclusion of asm/global_data.h.
Headers should be included directly by the files that need them,
rather than indirectly via global_data.h.
Reviewed-by: Patrice Chotard <[email protected]> #STMicroelectronics boards and STM32MP1 ram test driver
Tested-by: Anshul Dalal <[email protected]> #TI boards
Acked-by: Yao Zi <[email protected]> #TH1520
Signed-off-by: Peng Fan <[email protected]>
|
|
CMPC885 board can be pluged on a mother board with fibre interface, so
fibre interface MAC address must be initialised for that case.
Signed-off-by: Hugo Dubois <[email protected]>
Reviewed-by: CASAUBON Jean Michel <[email protected]>
Signed-off-by: Christophe Leroy <[email protected]>
|
|
Remove inclusion of common.h and add relevant
includes when necessary.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
When CMPC885 board is used for MIAE device, SCC2 SCC3 and SMC2
are used for serial lines. Therefore only SCC4 is available for
handling the TDM line.
In order to use SCC4 in QMC mode without loosing SMC2, SMC2
must be relocated.
Activate SMC relocation and relocate SMC2 at offset 0x1fc0 which
is unused.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
In order to know the motherboard type earlier, perform I/O ports
initialisation and FPGA loading in board_early_init_f() instead
of board_early_init_r().
This is needed to be able to load mpc8xx CPM microcode base on
motherboard type and before starting to use the CPM.
Console is not available yet so remove the printfs.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
A duplicated FPGA loading sequence appears after FPGA reset.
Remove it.
Fixes: dac3c6f625 ("board: cssi: Add new board MCR3000_2G")
Signed-off-by: Christophe Leroy <[email protected]>
|
|
All the code used to manage the mother boards will be
common to soon to come CPU board.
Move all that code into common.c
Signed-off-by: Christophe Leroy <[email protected]>
|
|
On cmpc885 board, the ethernet addresses are stored in an
EEPROM that is accessed through SPI.
A 3 bytes command is sent to the chip then the content
gets read. At the time being a single block access is
performed, ignoring the first 3 bytes read.
Reword the SPI transfer to first send 3 bytes then
receive the content of the EEPROM so that there don't be
3 dummy bytes at the beginning of the buffer.
And move the function into common.c so that it can be
reused by the board that will be added in a future patch.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
In preparation of the new cssi board called cmpcpro which
we be introduce in a future patch, move common
functions into a dedicated file in a common directory.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
This adds support for the MIAE and VGoIP devices.
Those devices have the same CPU board that the MCR3000_2G board.
The devices are very modular, they are provided with
interchangeable front and back panels.
Linux kernel is shipped with a device tree which contains all
possible setups, and U-boot eliminates unrelated nodes based on
detected hardware.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <[email protected]>
Reviewed-by: FRANJOU Stephane <[email protected]>
|
|
This adds a new board from CS GROUP. The board is called
MCR3000_2G, and has a CPU board called CMPC885.
That CPU board is shared with another equipment that will
be added in a later patch.
That board stores Ethernet MAC addresses in an EEPROM which
is accessed using SPI bus.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <[email protected]>
Reviewed-by: FRANJOU Stephane <[email protected]>
|
