| Age | Commit message (Collapse) | Author |
|---|
|
eDM SBC
Handle both MMC2 and SD2 boot devices as SDMMC device 1 on
Data Modul i.MX8M Mini eDM SBC. In case the system boots from
a microSD card, the BootROM reports boot device as SD2_BOOT
instead of MMC2_BOOT. Continue booting from that SDMMC device
instead of falling back to SDP. Note that SDMMC device 1 is
the microSD slot on this device, SDMMC device 2 is the eMMC,
but BootROM reports the numbers the other way around, hence
the potential confusion in this commit message.
Fixes: 0b97a394f6b7 ("ARM: imx: Replace YModem with SDP on Data Modul i.MX8M Mini eDM SBC SPL")
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Remove DECLARE_GLOBAL_DATA_PTR from files where gd is not used, and
drop the unnecessary inclusion of asm/global_data.h.
Headers should be included directly by the files that need them,
rather than indirectly via global_data.h.
Reviewed-by: Patrice Chotard <[email protected]> #STMicroelectronics boards and STM32MP1 ram test driver
Tested-by: Anshul Dalal <[email protected]> #TI boards
Acked-by: Yao Zi <[email protected]> #TH1520
Signed-off-by: Peng Fan <[email protected]>
|
|
Commit 86acdce2ba88 ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <[email protected]>
Tested-by: Adam Ford <[email protected]> #imx8mm_beacon
Tested-by: Bryan Brattlof <[email protected]>
Acked-by: Peng Fan <[email protected]> #NXP boards
|
|
The YModem support in SPL was never really used on this device,
the SDP support is much more convenient on i.MX8M Mini based
hardware. Replace the YModem support with SDP support.
The SDP can be utilized by forcing the board into SDP boot mode
by grounding test point right next to silkscreen label U30, and
then by using mfgtools 'uuu -brun spl flash.bin' once the device
enumerates on host system USB bus. The SDP capable USB port is
available on the USB micro-B port on the base board.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
Implement fdtdec_board_setup() auto-detection of ethernet PHY.
This uses properties of the hardware and pull resistor placement.
If GPIO1_16 RGMII_MDC is HIGH, then R530 (MX8MM eDM SBC) or
R390 (MX8MP eDM SBC) is populated. R530 or R390 is populated
only on boards with AR8031 PHY.
If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down is the
dominant pull resistor. This is the case on boards with BCM54213PE
PHY.
In case AR8031 PHY is populated, the PHY MDIO address is 0, in
case BCM54213PE PHY is populated, the PHY MDIO address is 1, the
fdtdec_board_setup() is used to patch the correct address into
the U-Boot control DT.
Enable broadcom PHY support to support both PHYs.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
We have a number of cases where the in-tree path of files and where
they presumably were when the first version of a patch were posted
differ slightly. Correct these to point at where the files are now.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Pull common.c into common subdirectory of the board file,
since this code can be reused by other Data Modul SBCs.
Drop the include of lpddr4_timing.h, which is unneeded.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The icache is enabled in common architecture code since commit:
2fa763baa1c ("ARM: imx: Enable instruction cache early on on i.MX8M")
Drop the board side duplicate code.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Pull this LPGPR unlock into common code, since it is used in multiple
systems already.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Adjust the DRAM timing settings for this board per ones provided
by hardware department. The change is applied to the LPDDR4 MR11
register CA ODT configuration, from RZQ/6 to RZQ/3, which fixes
stability issues on subset of boards. The DDR PHY PIE block has
been updated accordingly.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Replace the ad-hoc I2C register programming scripted in board
environment with U-Boot DM driver.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Enable CONFIG_SPL_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
