| Age | Commit message (Collapse) | Author |
|---|
|
Move dh_add_item_number_and_serial_to_env() to common code, so it
can be used by both STM32MP13xx and iMX8MP DHSOM. No functional
change.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
The isprint() checks printability across all 256 characters, some of the
upper 128 characters are printable and produce artifacts on UART. Call
isascii() first to only consider the bottom 7bit ASCII characters as
printable, and then check their printability using isprint(). This fixes
a rare misprint in case the ID page content is uninitialized or corrupted.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Christoph Niedermaier <[email protected]>
|
|
dh_get_value_from_eeprom_buffer()
The eip pointer in dh_get_value_from_eeprom_buffer() might be NULL.
The current NULL pointer check happens too late, after the eip was
accessed in variable assignment. Reorder the two, so the NULL pointer
check happens first, and any access second, otherwise the access may
trigger a hang or other undefined behavior.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Christoph Niedermaier <[email protected]>
|
|
This file reads from the environment but does not include the correct
header. Update it.
Signed-off-by: Simon Glass <[email protected]>
|
|
The env variable "SN" is used to store the serial number on DH electronics
SoMs. New SoMs will use the variable "dh_som_serial_number". To ensure
compatibility, these env variables are synchronized. This is achieved
using callback functions.
Signed-off-by: Christoph Niedermaier <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
The new i.MX8M Plus DHCOM rev.200 is populated with M24C32-D EEPROM
that contains an additional write-lockable page called ID page, which
is populated with a structure containing ethernet MAC addresses, DH
item number and DH serial number.
Because the write-lockable page is not present on rev.100 i.MX8MP DHCOM
SoM, test whether EEPROM ID page exists by setting up the i2c driver.
There may be multiple EEPROMs with an ID page on this platform, always
use the first one. The evaluation of the EEPROM ID page is done in two
steps. First, the content is read and checked. This is done to cache
the content of the EEPROM ID page. Second, the content is extracted
from the EEPROM buffer by requesting it.
For the ethernet MAC address the i.MX8M Plus DHCOM currently supports
parsing address from multiple sources in the following priority order:
1) U-Boot environment 'ethaddr'/'eth1addr' environment variable
2) SoC OTP fuses
3) On-SoM EEPROM
Add support for parsing the content of this new EEPROM ID page and place
it between 2) and 3) on the priority list. The new entry is 2.5) On-SoM
EEPROM write-lockable page.
Signed-off-by: Christoph Niedermaier <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
EEPROM on DHSOM
Check whether the ethernet interface is enabled at all before reading
MAC EEPROM. As a cost saving measure, it can happen that the MAC EEPROM
is not populated on SoMs which do not use ethernet.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
This is a starting point for unifying duplicate code in the DH board
files. The functions for setting up MAC addresses are very similar for
the i.MX6, i.MX8 and stm32mp1 based boards.
All pre-existing implementations follow the same logic:
(1) Check if ethaddr is already set in the environment
(2) If not, try to get it from a board specific location (e.g. fuse)
(3) If not, try to get it from eeprom
After this commit, (1) and (3) are implemented as common functions,
ready to be used by board specific files.
Furthermore there is an implementation of (2) for imx based boards.
Signed-off-by: Philip Oberfichtner <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
