| Age | Commit message (Collapse) | Author |
|---|
|
Currently, the board specific code evaluates only the first Ethernet
MAC address fuse, regardless of whether the first or second MAC
address is requested. When the function to determine the second
Ethernet MAC address is looking for the fused MAC address, it only
reads the first MAC address fuse and increment it by one to set
the second Ethernet MAC address. That is not the expected behavior
when two MAC addresses are fused, because this causes the second
fused MAC address to be ignored. Change this so that the second
fused MAC address will be used.
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Christoph Niedermaier <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Introduce timing patch which converts 2 GiB DRAM timings to 4 GiB 1-rank
timings. This is a new configuration which carries IS43LQ32K01B DRAM part.
The 512 MiB SoM strapping that was never used is repurposed for this part.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The 2 GiB and 4 GiB 2-rank DRAM timings on i.MX8MP DHCOM are very
similar. Instead of carrying around two copies of almost identical
timing tables, implement a patch of the 2 GiB table to convert it
into 4 GiB 2-rank table and pass the result to DRAM initialization
code. This saves us 13640 Bytes in SPL, and frees up space for more
DRAM initialization tables.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The DRAM size tables are shared by SPL and U-Boot proper, deduplicate
those tables into lpddr4_timing.h . No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The inline ECC configuration is identical for 2 GiB DRAM variants
and 4 GiB DRAM variants of the SoM, no matter the rank count. Fold
the ECC configuration directly into spl.c to simplify the upcoming
deduplication. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Remove DECLARE_GLOBAL_DATA_PTR from files where gd is not used, and
drop the unnecessary inclusion of asm/global_data.h.
Headers should be included directly by the files that need them,
rather than indirectly via global_data.h.
Reviewed-by: Patrice Chotard <[email protected]> #STMicroelectronics boards and STM32MP1 ram test driver
Tested-by: Anshul Dalal <[email protected]> #TI boards
Acked-by: Yao Zi <[email protected]> #TH1520
Signed-off-by: Peng Fan <[email protected]>
|
|
Move dh_add_item_number_and_serial_to_env() to common code, so it
can be used by both STM32MP13xx and iMX8MP DHSOM. No functional
change.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Commit 86acdce2ba88 ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <[email protected]>
Tested-by: Adam Ford <[email protected]> #imx8mm_beacon
Tested-by: Bryan Brattlof <[email protected]>
Acked-by: Peng Fan <[email protected]> #NXP boards
|
|
In case ENV_IS_IN_SPI_FLASH is disabled, returning ENVL_SPI_FLASH
leads to failure to find environment driver on start up. Fix this
by testing whether ENV_IS_IN_SPI_FLASH is enabled and if not, then
return ENVL_NOWHERE instead.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The new i.MX8M Plus DHCOM rev.200 is populated with M24C32-D EEPROM
that contains an additional write-lockable page called ID page, which
is populated with a structure containing ethernet MAC addresses, DH
item number and DH serial number.
Because the write-lockable page is not present on rev.100 i.MX8MP DHCOM
SoM, test whether EEPROM ID page exists by setting up the i2c driver.
There may be multiple EEPROMs with an ID page on this platform, always
use the first one. The evaluation of the EEPROM ID page is done in two
steps. First, the content is read and checked. This is done to cache
the content of the EEPROM ID page. Second, the content is extracted
from the EEPROM buffer by requesting it.
For the ethernet MAC address the i.MX8M Plus DHCOM currently supports
parsing address from multiple sources in the following priority order:
1) U-Boot environment 'ethaddr'/'eth1addr' environment variable
2) SoC OTP fuses
3) On-SoM EEPROM
Add support for parsing the content of this new EEPROM ID page and place
it between 2) and 3) on the priority list. The new entry is 2.5) On-SoM
EEPROM write-lockable page.
Signed-off-by: Christoph Niedermaier <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Update the MAINTAINERS file glob to cover all of i.MX8MP DHSOM related files.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Simon Glass <[email protected]> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
Both regulators_enable_boot_on/off() are unused and superseded by
regulator uclass regulator_post_probe(). Remove both functions.
Signed-off-by: Marek Vasut <[email protected]>
|
|
DHCOM SoM
U-Boot is currently unable to automatically enable regulators which
contain DT property regulator-always-on or regulator-boot-on. There
is an ongoing work to add this functionality to regulator core code,
but until the proper solution lands, add this awful workaround code
to force these regulators on. This is specifically needed to assure
the VIO regulator used to supply ethernet magnetics is enabled.
Signed-off-by: Marek Vasut <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
EEPROM on DHSOM
Check whether the ethernet interface is enabled at all before reading
MAC EEPROM. As a cost saving measure, it can happen that the MAC EEPROM
is not populated on SoMs which do not use ethernet.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB and for 2 GiB device the available DRAM size
becomes 1.8 GiB.
Signed-off-by: Marek Vasut <[email protected]>
|
|
In case the Buck5 and Buck6 regulators which supply DRAM Vdd1 and Vdd2/Vddq
respectively operate in automatic PWM/PFM mode, the DRAM EDAC detects more
correctable errors than if the regulators operate in forced PWM only mode.
Force DRAM regulators to forced PWM mode only to stop tempting the DRAM.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The current imx8mp-dhcom-som.dtsi describes production rev.200 SoM,
add DT overlay which reinstates rev.100 SoM description to permit
prototype rev.100 SoMs to be used until they get phased out.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Add DT overlays to support additional DH i.MX8MP DHCOM SoM 660-100
population options with 1x or 2x RMII PHY mounted on PDK2 or PDK3
carrier boards.
Use SPL DTO support to apply matching SoM specific DTO to cater
for the SoM differences. Remove ad-hoc patching of control DT from
fdtdec_board_setup().
Signed-off-by: Marek Vasut <[email protected]>
|
|
1. Convert all linker symbols to char[] type so that we can get the
corresponding address by calling array name 'var' or its address
'&var'. In this way, we can avoid some potential issues[1].
2. Remove unused symbol '_TEXT_BASE'. It has been abandoned and has
not been referenced by any source code.
3. Move '__data_end' to the arch x86's own sections header as it's
only used by x86 arch.
4. Remove some duplicate declared linker symbols. Now we use the
standard header file to declare them.
[1] This patch fixes the boot failure on MIPS target. Error log:
SPL: Image overlaps SPL
Fixes: 1b8a1be1a1f1 ("spl: spl_legacy: Fix spl_end address")
Signed-off-by: Shiji Yang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Make use of globs to cover all the DTs and defconfigs.
Fill in missing DH u-boot list name.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The FEC interface mode is now configured in common board_interface_eth_init()
and called by FEC MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The EQoS interface mode is now configured in common board_interface_eth_init()
and called by EQoS MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The i.MX8MP DHCOM SoM may be populated with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY attached to EQoS MAC, and either external RGMII PHY
or LAN8740Ai RMII PHY attached to FEC MAC. The SoM configuration can be
detected for each MAC by reading RX_CTL pull resistor state early on boot.
Make use of this, detect the exact PHY configuration, and patch control DT
accordingly so that the ethernet is configured correctly in U-Boot.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The DH electronics i.MX8M Plus DHCOM SoM currently supports only 4 GiB
of DRAM population option. Add another population option with 2 GiB of
DRAM. The chips used on the 2 GiB option are 2x K4F6E3S4HM-MGCJ .
Signed-off-by: Marek Vasut <[email protected]>
|
|
The PCA9450 reset configuration can now be performed by the PCA9450 PMIC
driver itself, remove the hard-coded variant from board code and let the
PMIC driver perform this task using one-liner:
```
$ sed -i '/set WDOG_B_CFG to cold reset/,+2 d' $(git grep -l PCA9450_RESET_CTRL.*0xA1 board/)
```
Venice and i.MX93 EVK required slight manual fix up.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Pull this LPGPR unlock into common code, since it is used in multiple
systems already.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Commit 99c7cc58e12 ("ddr: imx: Add i.MX9 DDR controller driver")
contains an inobvious side-effect which renders all systems using
DRAM controller at 3732 MT/s unbootable. The change is located in
ddrphy_init_set_dfi_clk(), where the switch case statement entry
3732 changed to entry 3733, so any board with DDR calibration data
for 3732 MT/s operations needs to be updated to 3733 MT/s to match
the change.
Since there is currently only one such board, update the board instead
of handling both 3732 and 3733 options in the driver. It is likely the
NXP MX8MP RPA update will follow and use the later value too.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
To reduce code duplication, let the imx8 based DH boards use the common
code for setting up their MAC addresses.
Signed-off-by: Philip Oberfichtner <[email protected]>
Tested-by: Marek Vasut <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
