| Age | Commit message (Collapse) | Author |
|---|
|
Our last sync with the kernel was 5.1.
We are so out of sync now, that tracking the patches and backporting
them one by one makes little sense and it's going to take ages.
This is an attempt to sync up Makefiles to 6.1.
Unfortunately due to sheer amount of patches this is not easy to review,
but that's what we decided during a community call for the bump to 5.1,
so we are following the same guidelines here.
Signed-off-by: Sughosh Ganu <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>a #rebased on -next
|
|
When binman is in use, most of the targets built by the Makefile are
inputs to binman. We then need a final rule to run binman to produce the
final outputs.
Rename the variable to indicate this, and add a new 'inputs' target.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Add Intel Edison board which is using U-Boot.
The patch is based on work done by the following people (in alphabetical
order):
Aiden Park <[email protected]>
Dukjoon Jeon <[email protected]>
eric.park <[email protected]>
Fabien Chereau <[email protected]>
Felipe Balbi <[email protected]>
Scott D Phillips <[email protected]>
Sebastien Colleur <[email protected]>
Steve Sakoman <[email protected]>
Vincent Tinelli <[email protected]>
In case we're building for Intel Edison, we must have 4096 bytes of
zeroes in the beginning on u-boot.bin. This is done in
board/intel/edison/config.mk.
First run sets hardware_id environment variable which is read from
System Controller Unit (SCU).
Serial number (serial# environment variable) is generated based on eMMC
CID.
MAC address on USB network interface is unique to the board but kept the
same all over the time.
Set mac address from U-Boot using following scheme:
OUI = 02:00:86
next 3 bytes of MAC address set from eMMC serial number
This allows to have a unique mac address across reboot and flashing.
Signed-off-by: Vincent Tinelli <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
[bmeng: Add MAINTAINERS file for Intel Edison board]
Signed-off-by: Bin Meng <[email protected]>
|
