| Age | Commit message (Collapse) | Author |
|---|
|
Restyle all Kconfigs:
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Signed-off-by: Johan Jonker <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Acked-by: Adam Ford <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
Cc: Adam Ford <[email protected]>
Cc: Vanessa Maegima <[email protected]>
Cc: Otavio Salvador <[email protected]>
Cc: Igor Opaniuk <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The board_boot_order() function currenly assumes that the boot source
is MMC/eMMC, but this isn't true for the NAND devices.
This patch cleans up board_boot_order() to check for NAND, SD, ESD,
MMC or EMMC. Anything beyond these are not supported, so it will
default back to the serial downloader if any of those devices are not
available.
Fixes: 9fb50c68daa6 ("ARM: imx6q_logic: Fix MMC2 booting")
Signed-off-by: Adam Ford <[email protected]>
|
|
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
These functions belong in serial.h so move them over.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with
-u-boot.dtsi entries to include the pinmuxing in SPL, the manual
code setting up the pinmux can go away.
This patch removes the legacy pinmuxing code from the board file.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
With the reverting of a previous change to spl_boot_device,
this board needs a new solution to determining if we're booting
from MMC1 or MMC2.
This patch creates board_boot_order function which overrides the
standard, and returns not only MMC1, or MMC2, but also can fall
back to NAND or the serial downloader should other boot options
fail.
Signed-off-by: Adam Ford <[email protected]>
|
|
In order to call preloader_console_init from board_init_f when
DM_SERIAL is enabled, it neesd to call spl_early_init() to get early access
to DM and device tree.
This patch calls spl_early_init just before preloader_console_init()
and enables DM_SERIAL and SPL_DM_SERIAL.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Per the workflow found in crt0.S, we don't need to clear BSS in
board_init_f nor do we need to call board_init_r since that will be
done for us from main when we return from board_init_f.
This patch removes the unneeded function calls from board_init_f.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and
usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file
which will enable these functions so SPL can properly setup UART, detect
microSD card, and startup.
Fixes: 8f4691e31a18 ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled,
remove MMC init")
Signed-off-by: Adam Ford <[email protected]>
|
|
Move env_set() over to the new header file.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Since the board uses SPL_OF_CONTROL now, we don't need to
explicitly initialize the MMC driver, but we still need to
pinmux the corresponding pins. This patch removes the
initialization code and leave just the muxing behind.
Signed-off-by: Adam Ford <[email protected]>
|
|
Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <[email protected]>
Tested-by: Steffen Dirkwinkel <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Reviewed-by: Martyn Welch <[email protected]>
Acked-by: Jason Liu <[email protected]>
|
|
The board file uses the processor type to determine what dtb file
is set. Unfortunately, if the user wants to manually set this,
it get gets overwritten upon boot. This patch adds a check to
see if the value is already set and only changes it if the value
is empty.
Signed-off-by: Adam Ford <[email protected]>
|
|
The Ethernet has been broken for some time. This patch unifies
this board with a few others that use a similar approach to
enabling phy. This fixes ar8031 Ethernet controller so it works.
Signed-off-by: Adam Ford <[email protected]>
|
|
This patch enables Falcon Mode by default and updates the README
file to show instructions on how to run from the micro SD card
or eMMC. This patch also enables fatwrite to help assist with
writing the 'args' to the microSD card.
Signed-off-by: Adam Ford <[email protected]>
|
|
The i.MX6 SOM and development kits have undergone significant
updates and changes over the past few months. This re-sync's
the U-Boot with Logic PD's BSP.
Signed-off-by: Adam Ford <[email protected]>
|
|
The MMC booting wasn't previously fitting into the codespace.
This patch enables MMC booting from the baseboard by reducing
some DM overhead during SPL.
Signed-off-by: Adam Ford <[email protected]>
|
|
Since the vast majority of i.MX6 boards are migrating to SPL,
this patch converts im6q_logic to SPL and enables the SDP for
loading SPL and u-boot.img over USB. The Falcon mode only
supports NAND flash as of now due to limited space/RAM, but
all i.MX6D/Q SOM's from Logic PD have internal NAND from which
to boot.
Signed-off-by: Adam Ford <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
When building with W=1 errors like the one below is seen:
board/freescale/mx6sabresd/mx6sabresd.c:546:5: warning:
no previous prototype for ‘overwrite_console’
[-Wmissing-prototypes] int overwrite_console(void)
Fix the build warnings by including <input.h>.
Signed-off-by: Diego Dorta <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <[email protected]>
CC: Fabio Estevam <[email protected]>
CC: Akshay Bhat <[email protected]>
CC: Ken Lin <[email protected]>
CC: Marek Vasut <[email protected]>
CC: Heiko Schocher <[email protected]>
CC: "Sébastien Szymanski" <[email protected]>
CC: Christian Gmeiner <[email protected]>
CC: Stefan Roese <[email protected]>
CC: Patrick Bruenn <[email protected]>
CC: Troy Kisky <[email protected]>
CC: Nikita Kiryanov <[email protected]>
CC: Otavio Salvador <[email protected]>
CC: "Eric Bénard" <[email protected]>
CC: Jagan Teki <[email protected]>
CC: Ye Li <[email protected]>
CC: Peng Fan <[email protected]>
CC: Adrian Alonso <[email protected]>
CC: Alison Wang <[email protected]>
CC: Tim Harvey <[email protected]>
CC: Martin Donnelly <[email protected]>
CC: Marcin Niestroj <[email protected]>
CC: Lukasz Majewski <[email protected]>
CC: Adam Ford <[email protected]>
CC: "Albert ARIBAUD (3ADEV)" <[email protected]>
CC: Boris Brezillon <[email protected]>
CC: Soeren Moch <[email protected]>
CC: Richard Hu <[email protected]>
CC: Wig Cheng <[email protected]>
CC: Vanessa Maegima <[email protected]>
CC: Max Krummenacher <[email protected]>
CC: Stefan Agner <[email protected]>
CC: Markus Niebel <[email protected]>
CC: Breno Lima <[email protected]>
CC: Francesco Montefoschi <[email protected]>
CC: Jaehoon Chung <[email protected]>
CC: Scott Wood <[email protected]>
CC: Joe Hershberger <[email protected]>
CC: Anatolij Gustschin <[email protected]>
CC: Simon Glass <[email protected]>
CC: "Andrew F. Davis" <[email protected]>
CC: "Łukasz Majewski" <[email protected]>
CC: Patrice Chotard <[email protected]>
CC: Nobuhiro Iwamatsu <[email protected]>
CC: Hans de Goede <[email protected]>
CC: Masahiro Yamada <[email protected]>
CC: Stephen Warren <[email protected]>
CC: Andre Przywara <[email protected]>
CC: "Álvaro Fernández Rojas" <[email protected]>
CC: York Sun <[email protected]>
CC: Xiaoliang Yang <[email protected]>
CC: Chen-Yu Tsai <[email protected]>
CC: George McCollister <[email protected]>
CC: Sven Ebenfeld <[email protected]>
CC: Filip Brozovic <[email protected]>
CC: Petr Kulhavy <[email protected]>
CC: Eric Nelson <[email protected]>
CC: Bai Ping <[email protected]>
CC: Anson Huang <[email protected]>
CC: Sanchayan Maity <[email protected]>
CC: Lokesh Vutla <[email protected]>
CC: Patrick Delaunay <[email protected]>
CC: Gary Bisson <[email protected]>
CC: Alexander Graf <[email protected]>
CC: [email protected]
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Christian Gmeiner <[email protected]>
|
|
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM. Items in the dtsi file
are specific to the SOM itself. Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.
Signed-off-by: Adam Ford <[email protected]>
|
