| Age | Commit message (Collapse) | Author |
|---|
|
Our last sync with the kernel was 5.1.
We are so out of sync now, that tracking the patches and backporting
them one by one makes little sense and it's going to take ages.
This is an attempt to sync up Makefiles to 6.1.
Unfortunately due to sheer amount of patches this is not easy to review,
but that's what we decided during a community call for the bump to 5.1,
so we are following the same guidelines here.
Signed-off-by: Sughosh Ganu <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>a #rebased on -next
|
|
Per a private email, drop Luka Perkov from MAINTAINERS entries.
Reviewed-by: Tony Dinh <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Add Luka Perkov to CRS3xx-98DX3236 MAINTAINERS.
Signed-off-by: Luka Kovacic <[email protected]>
Cc: Luka Perkov <[email protected]>
Cc: Jakov Petrina <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <[email protected]>
Cc: Luka Perkov <[email protected]>
Cc: Jakov Petrina <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <[email protected]>
Cc: Luka Perkov <[email protected]>
Cc: Jakov Petrina <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
MikroTik CRS305-1G-4S Bit board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
The Bit board variant is added, which has a bigger Macronix flash.
Add basic U-Boot, UART and Winbond SPI flash support.
Signed-off-by: Luka Kovacic <[email protected]>
Cc: Luka Perkov <[email protected]>
Cc: Jakov Petrina <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier
implementation of new CRS3xx series boards, based on Marvell Prestera
98DX3236.
Signed-off-by: Luka Kovacic <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Cc: Luka Perkov <[email protected]>
Cc: Jakov Petrina <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present some boards generate kwbimage.cfg in the source tree
during the build. This breaks buildman testing on some systems
where the source tree is read-only. Update makefile rules to
generate it in the build tree instead.
Note some other boards have the kwbimage.cfg file written in
advance, hence we need check if the file exists in the build
tree first, otherwise we fall back to one in the source tree.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Chris Packham <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and
like some of the other similar boards requires bin_hdr.
bin_hdr (DDR3 init stage) is currently retrieved from the stock
bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip
support and writing env to SPI flash.
Signed-off-by: Luka Kovacic <[email protected]>
Reviewed-by: Chris Packham <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
