| Age | Commit message (Collapse) | Author |
|---|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <[email protected]>
|
|
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This function is empty, drop it.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Steven Lawrance <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This header file should not be included in other header files. Remove it
from each one and use a forward declaration instead.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Implement method board_phy_config to configure the external phys
on the pcb90.
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
Implement method board_phy_config to configure the phy for pcb120.
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
In Serval SoC family there are 2 different pcb, both of them have the same
phy, but with different version. Therefore implement board_phy_config
and set all the phys in the same way.
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
When detecting the board, it was reading a register in the GPIO page of
the phy and based on that value it was making a decision. The bug was that
after the GPIO page for the first phy was set it was not reseted back.
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
In Jaguar2 SoC family there are 3 different pcb. Each of this needs
to configure the phys in different ways. Therefore implement the
function board_phy_config and based on pcb configure them accordingly.
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
When power cycle the Jaguar2 boards, it couldn't read the
phys, therefore it always deduce that the board type is
pcb111.
Add a small delay after setting the gpio pins, fix the
issue.
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
Enable debug uart for Jaguar2 SoC family.
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
Add board support and configuration for Jaguar2 SoC family.
The detection of the board type is based on the phy ids.
Signed-off-by: Horatiu Vultur <[email protected]>
Reviewed-by: Daniel Schwierzeck <[email protected]>
|
|
Add board support, configuration and DTS for Servalt SoC
family. Currently there is one board in this family.
Reviewed-by: Daniel Schwierzeck <[email protected]>
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
On some ocelots platform a workaround is needed in order to be able to
reset the switch without resetting the DDR.
Signed-off-by: Gregory CLEMENT <[email protected]>
|
|
Add board support and configuration for Jaguar2 SOC family.
The detection of the board type in this family is based on the phy ids.
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'ocelot' pcb123 and pcb120.
Signed-off-by: Lars Povlsen <[email protected]>
|
|
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'luton' SoC.
Signed-off-by: Lars Povlsen <[email protected]>
|
|
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.
Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.
Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.
Signed-off-by: Lars Povlsen <[email protected]>
|
|
Adding the support for the Luton boards PCB91 which share common code with
the Ocelots boards, including board code, device tree and configuration.
Signed-off-by: Gregory CLEMENT <[email protected]>
|
|
Adding the support for 2 boards sharing common code for Ocelot chip:
PCB120 and PCB123
Signed-off-by: Gregory CLEMENT <[email protected]>
|
