| Age | Commit message (Collapse) | Author |
|---|
|
Since most boards now use the same generic device config header, move its
setup to SoC Kconfig instead of setting SYS_CONFIG_NAME in each board's
Kconfig.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Most device headers contain SoC specific part and common Tegra post part.
Add a generic header which can be used by any Tegra device of one of the
supported SoC generations (T20, T30, T114, T124 or T210) without need in
device specific configuration.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Convert CFG_TEGRA_BOARD_STRING into Kconfig option and move it into device
board Kconfig.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
This file is being removed so drop remaining references to it.
Signed-off-by: Simon Glass <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.
Insert the Tegra SoC select menu between the arch select and the
board select.
Architecture select
|-- Tegra Platform (Tegra)
|- Tegra SoC select (Tegra20 / 30 / 114 / 124)
|- Board select
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:
config TEGRA
bool
select SPL
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Cc: Tom Warren <[email protected]>
|
|
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <[email protected]>
Suggested-by: Tom Rini <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
This renames all the Tegra20 pinmux pins and functions so they have a
prefix which matches the type name.
The entries in tegra20_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Albert ARIBAUD <[email protected]>
Cc: Andreas Bießmann <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Prafulla Wadaskar <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Vipin Kumar <[email protected]>
Cc: Tom Warren <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc.
Tested on Seaboard, fully functional.
Tamonten boards (medcom-wide, plutux, and tec) use a different/new
dtsi file w/common settings.
Signed-off-by: Tom Warren <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
Reviewed-by: Stephen Warren <[email protected]>
|
|
Harmony contains an SD slot with all 8 bits routed. This allows plugging
in an eMMC-chip-in-SD-form-factor.
Seaboard/Springbank/Ventana/AC100 all have an eMMC chip with all 8 bits
hooked up.
Now that the U-Boot eMMC code fully supports 8-bit operation, initialize
those ports as 8-bit instead of 4-bit to improve performance.
Whistler was already registering its ports as 8-bit.
TrimSlice doesn't have any 8-bit ports.
I don't have any Avionic Design boards nor the Colibri board to test with.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
The ULPI port is routed onto pins on the mini PCI Express connector. A
standard breakout board may be used to access the port.
* Add required DT entries to configure the ULPI port.
* Setup up the ULPI pinmux in the board code.
* Enable multiple USB controller and ULPI support in the board config.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Rename board provided gpio_config_uart() to
gpio_early_init_uart() as it does the same thing as the equally
called function provided by the uart-switch code. This allows
to simply call this function in early board init whether or not
we are building with CONFIG_UART_SWITCH defined.
Also provide a weak symbol for this function, to avoid the
need to provide this function for boards that don't need any
fixup.
This patch supersedes the earlier posted
"tegra: convert gpio_config_uart to weak symbol".
Build tested with MAKEALL -s tegra20
Signed-off-by: Lucas Stach <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <[email protected]>
|
|
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.
Upcoming Tegra30 port will use common code/defines/names where possible.
Signed-off-by: Tom Warren <[email protected]>
Acked-by: Stephen Warren <[email protected]>
|
|
None of harmony, seaboard, ventana, whistler directly build files from
../common/, so there's no need to mkdir the obj directory for such files.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.
Signed-off-by: Allen Martin <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Tested-by: Thierry Reding <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <[email protected]>
|
|
Use the new funcmux_select() feature to set up the MMC pin mux.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Seaboard changes have removed the need for common/board.o in the
Makefile. Propagate this change to the other Tegra2 builds.
Signed-off-by: Tom Warren <[email protected]>
|
|
tegra2_mmc_init() is implemented by the Tegra2 MMC driver. Since most of
the Tegra2-based boards will need to call it, this commit exports it in
the new public asm/arch/mmc.h header file to prevent each board from
providing its own prototype.
Signed-off-by: Thierry Reding <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Tested-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
modify that function to perform all required GPIO initialization. This
removes the need for board files to perform these operations.
Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
GPIOs to use.
Update affected call-sites in seaboard.c and harmony.c. Note that this
change should make all SD ports work on Harmony, since the required GPIO
setup is now being performed.
v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
Remove prototype of gpio_config_mmc() from board.h
Signed-off-by: Stephen Warren <[email protected]>
Cc: Andy Fleming <[email protected]>
Tested-by: Simon Glass <[email protected]>
Acked-by: Simon Glass <[email protected]>
Acked-by: Andy Fleming <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
For Seaboard, this is mostly a cut/paste of board_mmc_init() and
pin_mux_mmc() into seaboard.c; pin_mux_mmc() was modified to add some
missing pinmux_tristate_disable calls for the GPIOs.
For Harmony, those functions were modified to configure SDMMC2 (index 2)
instead of SDMMC3 (index 1), since that's what is present on the board.
However, harmony.c is still missing the required GPIO setup, so neither
port is likely to function correctly yet. This will be fixed in the next
change.
v4: Include board.h to prototype tegra2_mmc_init().
Signed-off-by: Stephen Warren <[email protected]>
Tested-by: Simon Glass <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This adds the required GPIO and pinmux configuration to make eMMC / SD work
on Seaboard.
Signed-off-by: Simon Glass <[email protected]>
Tested-by: Tom Warren <[email protected]>
|
|
Seems people fixed their files to use libfoo.o, but didn't actually
update the creation targets to use $(cmd_link_o_target). Update the
rest of the Makefile's found with grep.
Signed-off-by: Mike Frysinger <[email protected]>
Tested-by: Simon Glass <[email protected]>
|
|
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <[email protected]>
|
|
The out-of-tree build fails because the Makefiles in question depend on
source files of another directory but do not explicitly mkdir that
directory.
As a matter of fact, other Makefiles under board/*/ directory that refer
to source files under another directory explicitly call mkdir.
This patch adds explicit mkdir's to the Makefiles in question, and
verifies that out-of-tree build is working.
Signed-off-by: Che-Liang Chiou <[email protected]>
Cc: Albert Aribaud <[email protected]>
|
|
Signed-off-by: Tom Warren <[email protected]>
|
|
Signed-off-by: Tom Warren <[email protected]>
|
