| Age | Commit message (Collapse) | Author |
|---|
|
board early initialize fec ethernet controller pinmux
only when FEC is enabled
Signed-off-by: Parthiban Nallathambi <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
boot order was added to handle both SD and eMMC. But commit
14d319b1 introduced to handle both eMMC and SD globally.
Signed-off-by: Parthiban Nallathambi <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Booting from NAND needs nandbcb and nand boot device selection
Signed-off-by: Parthiban Nallathambi <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
This code uses HW difference on the USB_RESET pin (added PULL UP resistor
on the L333 rev) to distinguish between two BK4 HW revisions.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: Simon Goldschmidt <[email protected]>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Move env_set() over to the new header file.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
The rk3288_detect_reset_reason() is per-SoC operation, move
it to rk3288.c, and extend the rk_board_late_init() with
rk3288_board_late_init() to make all the board works fine
as before.
Signed-off-by: Kever Yang <[email protected]>
|
|
phycore_init() is use for phycore board only, it should be move back
to phycore-rk3288.c
Signed-off-by: Kever Yang <[email protected]>
|
|
Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec
phyBOARD-Wega AM335x.
CPU : AM335X-GP rev 2.1
Model: Phytec AM335x phyBOARD-WEGA
DRAM: 256 MiB
NAND: 256 MiB
MMC: OMAP SD/MMC: 0
eth0: ethernet@4a100000
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART
- USB (host)
Device trees were taken from Linux mainline:
commit 37624b58542f ("Linux 5.1-rc7")
Signed-off-by: Niel Fourie <[email protected]>
Signed-off-by: Parthiban Nallathambi <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Tested-by: Marek Vasut <[email protected]>
|
|
Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <[email protected]>
Tested-by: Steffen Dirkwinkel <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Reviewed-by: Martyn Welch <[email protected]>
Acked-by: Jason Liu <[email protected]>
|
|
Extend PHYTEC phyBOARD-i.MX6UL for phyCORE-i.MX6UL SoM (PCL063)
with eMMC on SoM.
CPU: Freescale i.MX6ULL rev1.0 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 38C
Reset cause: POR
Model: Phytec phyBOARD-i.MX6ULL-Segin SBC
Board: PHYTEC phyCORE-i.MX6ULL
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial@02020000
Out: serial@02020000
Err: serial@02020000
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- eMMC
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Parthiban Nallathambi <[email protected]>
|
|
u-boot,dm-spl property is specific to U-Boot, so created one
for i.MX6ULL platforms.
Signed-off-by: Parthiban Nallathambi <[email protected]>
|
|
BK4 requires setup of 50MHz reference clock for its KSZ8081 PHY devices.
Signed-off-by: Lukasz Majewski <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This commit introduces the board specific function to read fused mac
address.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
As one has moved to DM based LEDs, this code is required to setup the
default state.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
This code allows reusing the default u-boot as in the late board init, the
default envs are restored and proper recovery scripts executed.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
This commit cleans up the pcm052.c file to remove dead code after moving to
DTS and DM.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
This commit provides distinction between PCM052 and BK4.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
The "m4go" provides exactly the same functionality as the IMX generic
"bootaux" command. Remove it to not duplicate the code.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
As the I2C2 clock is now enabled in the generic clock code, we can remove
this code from a board file.
Signed-off-by: Lukasz Majewski <[email protected]>
Tested-by: Marcel Ziswiler <[email protected]>
|
|
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit f411b5cca48f ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <[email protected]>
|
|
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time. As part of that, address a number of
missing MAINTAINERS entires. In the case of a missing file, I have put
the original submitter down. In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.
Signed-off-by: Tom Rini <[email protected]>
|
|
Read SoM information from EEPROM and set ethaddr in late init.
Signed-off-by: Wadim Egorov <[email protected]>
Acked-by: Philipp Tomsich <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
In case of 2 banks, the address space of the first CS must be defined
and not let to the higher value.
Add support for SOM with a single bank of RAM. It was tested with i.MX6Q
modules in the following configurations:
- 2 Banks, 4 GB
- 2 Banks, 1 GB
- 1 Bank, 1 GB
Signed-off-by: Stefano Babic <[email protected]>
|
|
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.
Signed-off-by: Breno Lima <[email protected]>
Acked-by: Stefano Babic <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig.
Signed-off-by: Tom Rini <[email protected]>
|
|
Rename this function for consistency with env_get().
Signed-off-by: Simon Glass <[email protected]>
|
|
Rename this function for consistency with env_set().
Signed-off-by: Simon Glass <[email protected]>
|
|
Add support for Phytec pfla02, equipped with NAND.
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 31C
Reset cause: POR
I2C: ready
DRAM: 1 GiB
NAND: 2048 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total
16 MiB
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Stefano Babic <[email protected]>
CC: Stefan Christ <[email protected]>
CC: Stefan Müller-Klieser <[email protected]>
CC: Christian Hemp <[email protected]>
|
|
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <[email protected]>
CC: Fabio Estevam <[email protected]>
CC: Akshay Bhat <[email protected]>
CC: Ken Lin <[email protected]>
CC: Marek Vasut <[email protected]>
CC: Heiko Schocher <[email protected]>
CC: "Sébastien Szymanski" <[email protected]>
CC: Christian Gmeiner <[email protected]>
CC: Stefan Roese <[email protected]>
CC: Patrick Bruenn <[email protected]>
CC: Troy Kisky <[email protected]>
CC: Nikita Kiryanov <[email protected]>
CC: Otavio Salvador <[email protected]>
CC: "Eric Bénard" <[email protected]>
CC: Jagan Teki <[email protected]>
CC: Ye Li <[email protected]>
CC: Peng Fan <[email protected]>
CC: Adrian Alonso <[email protected]>
CC: Alison Wang <[email protected]>
CC: Tim Harvey <[email protected]>
CC: Martin Donnelly <[email protected]>
CC: Marcin Niestroj <[email protected]>
CC: Lukasz Majewski <[email protected]>
CC: Adam Ford <[email protected]>
CC: "Albert ARIBAUD (3ADEV)" <[email protected]>
CC: Boris Brezillon <[email protected]>
CC: Soeren Moch <[email protected]>
CC: Richard Hu <[email protected]>
CC: Wig Cheng <[email protected]>
CC: Vanessa Maegima <[email protected]>
CC: Max Krummenacher <[email protected]>
CC: Stefan Agner <[email protected]>
CC: Markus Niebel <[email protected]>
CC: Breno Lima <[email protected]>
CC: Francesco Montefoschi <[email protected]>
CC: Jaehoon Chung <[email protected]>
CC: Scott Wood <[email protected]>
CC: Joe Hershberger <[email protected]>
CC: Anatolij Gustschin <[email protected]>
CC: Simon Glass <[email protected]>
CC: "Andrew F. Davis" <[email protected]>
CC: "Łukasz Majewski" <[email protected]>
CC: Patrice Chotard <[email protected]>
CC: Nobuhiro Iwamatsu <[email protected]>
CC: Hans de Goede <[email protected]>
CC: Masahiro Yamada <[email protected]>
CC: Stephen Warren <[email protected]>
CC: Andre Przywara <[email protected]>
CC: "Álvaro Fernández Rojas" <[email protected]>
CC: York Sun <[email protected]>
CC: Xiaoliang Yang <[email protected]>
CC: Chen-Yu Tsai <[email protected]>
CC: George McCollister <[email protected]>
CC: Sven Ebenfeld <[email protected]>
CC: Filip Brozovic <[email protected]>
CC: Petr Kulhavy <[email protected]>
CC: Eric Nelson <[email protected]>
CC: Bai Ping <[email protected]>
CC: Anson Huang <[email protected]>
CC: Sanchayan Maity <[email protected]>
CC: Lokesh Vutla <[email protected]>
CC: Patrick Delaunay <[email protected]>
CC: Gary Bisson <[email protected]>
CC: Alexander Graf <[email protected]>
CC: [email protected]
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Christian Gmeiner <[email protected]>
|
|
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Philipp Tomsich <[email protected]>
|
|
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <[email protected]>
|
|
The variable nfc_pads is only referenced when CONFIG_CMD_NAND is set,
add a gaurd. The variable gpio_pads is never referenced, drop it. The
variable usdhc4_pads are only referenced when we do not have
CONFIG_CMD_NAND set and we are not doing an SPL build, modify the
existing guard.
Cc: Stefano Babic <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
|
|
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <[email protected]>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <[email protected]>
|
|
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137be ("ARM:
mx6: move to a standard arch/board approach").
Signed-off-by: Stefan Agner <[email protected]>
|
|
The sequence erroneously launched the DDR controller
initialization before the pad muxing was done, causing
DRAM size computation to hang.
Configuring the pads first then launching DDR controller
initialization prevents the DRAM hanging.
Signed-off-by: Albert ARIBAUD (3ADEV) <[email protected]>
|
|
Fixed typo for doc/README.imximage on respective imximage.cfg files.
Cc: Tom Rini <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Fabio Estevam <[email protected]>
Acked-by: Peng Fan <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Signed-off-by: Albert ARIBAUD (3ADEV) <[email protected]>
|
|
PCM052 SoMs may be equipped with various sizes of DDR.
Keep default of 256MB; new PCM052-based targets will
specify their actual DDR size.
Linux command line is auto-adjusted to DDR size.
Signed-off-by: Albert ARIBAUD (3ADEV) <[email protected]>
|
|
Add the 'm4go' command to pcm052-based targets.
It loads scatter file images.
Signed-off-by: Albert ARIBAUD (3ADEV) <[email protected]>
|
|
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <[email protected]>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <[email protected]>
|
