| Age | Commit message (Collapse) | Author |
|---|
|
Convert the board to use DM_PMIC instead of the legacy SPL I2C/PMIC
handling.
Changes include:
- Enable DM_PMIC, DM_PMIC_PCA9450, and SPL_DM_PMIC_PCA9450 in defconfig.
- Drop legacy SPL I2C and PMIC options.
- Remove manual I2C1 pad setup and legacy power_pca9450_init() usage.
- Use DM-based pmic_get() with the DT node "pmic@25".
- Update PMIC register programming to use struct udevice API.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Yannic Moog <[email protected]>
Tested-by: Yannic Moog <[email protected]>
Reviewed-by: Teresa Remmet <[email protected]>
|
|
Convert the board to use DM_PMIC instead of the legacy SPL I2C/PMIC
handling.
Changes include:
- Enable DM_PMIC, DM_PMIC_PCA9450, and SPL_DM_PMIC_PCA9450 in defconfig.
- Drop legacy SPL I2C and PMIC options.
- Remove manual I2C1 pad setup and legacy power_pca9450_init() usage.
- Use DM-based pmic_get() with the DT node "pmic@25".
- Update PMIC register programming to use struct udevice API.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Yannic Moog <[email protected]>
Tested-by: Yannic Moog <[email protected]>
Reviewed-by: Teresa Remmet <[email protected]>
|
|
As the PHYTEC phyCORE-i.MX91 [1] is just another variant of the existing
PHYTEC phyCORE-i.MX93 SoM but with i.MX91 SoC populated instead, add it
to the existing board-code "phycore_imx93", and rename that board to
"phycore_imx91_93" to reflect the dual SoCs support. While at it, also
rename and change common files accordingly. This way i.MX91 and i.MX93
SoC variants of the phyCORE SoM share most of the code and documentation
without duplication, while maintaining own device-tree and defconfigs
for each CPU variant.
Supported features:
- 1GB LPDDR4 RAM
- Debug UART
- EEPROM
- eMMC
- Ethernet
- SD-card
- USB
Product page SoM:
[1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-91-93/
Signed-off-by: Primoz Fiser <[email protected]>
|
|
Sparsh Kumar <[email protected]> says:
This series updates the Resource Management (RM) configuration files
for AM62 family devices to align with the TIFS v11.02.09 firmware.
Background
----------
With the latest TIFS firmware (v11.02.09), an additional virtual
interrupt and event is reserved for MCU cores to DM usage on am62x,
am62ax, and am62px devices. This series brings the rm-cfg and
tifs-rm-cfg files in sync with these firmware changes across both
TI reference boards and vendor boards.
These changes are backward compatible with older TIFS firmware versions.
Additionally, the am62x platform was originally introduced without a
tifs-rm-cfg.yaml file, unlike other platforms in the AM62 family.
This series addresses that gap and enables tifs-rm-cfg in binman for
am625-sk and am62p-sk platforms.
Changes
-------
TI reference boards (patches 1-4):
- Update rm-cfg.yaml for am62x, am62ax, am62px
- Sync am62px tifs-rm-cfg.yaml with TIFS firmware template
- Add missing tifs-rm-cfg.yaml for am62x
- Enable tifs-rm-cfg in binman for am625-sk and am62p-sk
Vendor boards (patches 5-9):
- beagleplay (am62x-based)
- phytec phycore_am62x
- toradex verdin-am62
- phytec phycore_am62ax
- toradex verdin-am62p
with the required interrupt reservation. The tifs-rm-cfg.yaml files
cannot be updated without access to the corresponding SysConfig files,
as both rm-cfg.yaml and tifs-rm-cfg.yaml must remain in sync.
Link: https://lore.kernel.org/r/[email protected]
|
|
reservation
With the latest v11.02.09 TIFS firmware, an additional
virtual interrupt and event is reserved for MCU cores
to DM usage on am62ax devices.
Update the rm-cfg to reflect this new reservation.
Signed-off-by: Sparsh Kumar <[email protected]>
|
|
With the latest v11.02.09 TIFS firmware, an additional
virtual interrupt and event is reserved for MCU cores
to DM usage on am62x devices.
Update the rm-cfg to reflect this new reservation.
Signed-off-by: Sparsh Kumar <[email protected]>
|
|
In case board is booted from USB, enter fastboot by default to enable
the UUU flashing. In case of abort continue with the regular bootstd
scan. User also has possibility to override the default bootcmd from
the environment. Last but not least, this syncs behavior with other
PHYTEC boards from the i.MX family.
Signed-off-by: Primoz Fiser <[email protected]>
Reviewed-by: Benjamin Hahn <[email protected]>
|
|
As explained in commit 03d2d5fc003f ("board: sifive: unmatched: set
fdtfile with unquoted variable.") using the syntax of
'fdtfile=CONFIG_DEFAULT_FDT_FILE' in the plain text environment files
will lead to extraneous and problematic "s in the output. This is fixed
by using fdtfile=DEFAULT_FDT_FILE which was introduced recently.
Acked-by: Peng Fan <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove DECLARE_GLOBAL_DATA_PTR from files where gd is not used, and
drop the unnecessary inclusion of asm/global_data.h.
Headers should be included directly by the files that need them,
rather than indirectly via global_data.h.
Reviewed-by: Patrice Chotard <[email protected]> #STMicroelectronics boards and STM32MP1 ram test driver
Tested-by: Anshul Dalal <[email protected]> #TI boards
Acked-by: Yao Zi <[email protected]> #TH1520
Signed-off-by: Peng Fan <[email protected]>
|
|
device for non SPLs"
This series from Dominik Haller <[email protected]> provides a way for
TI K3 platforms to determine their boot device outside of SPL and then
adds support for the PHYTEC phyCORE-AM68x/TDA4x SoM.
Link: https://lore.kernel.org/r/[email protected]
|
|
Add documentation for the PHYTEC phyCORE-AM68x/TDA4x (J721S2 family) SoM.
Signed-off-by: Dominik Haller <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
|
|
Add support for the PHYTEC phyCORE-AM68x/TDA4x (J721S2 family) SoM.
Supported features:
- 4GB LPDDR4 RAM
- eMMC
- SD-Card
- Ethernet
- OSPI
- AVS
- debug UART
Signed-off-by: Dominik Haller <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
|
|
PHYTEC maintains an actively monitored mailing list for upstream
activities: [email protected]. Add it to the MAINTAINERS
entries for PHYTEC boards we actively develop and contribute to.
Signed-off-by: Wadim Egorov <[email protected]>
Acked-by: Teresa Remmet <[email protected]>
|
|
This series from Daniel Schultz <[email protected]> lays the
groundwork for the phyFLEX SOMs from phytec.
Link: https://lore.kernel.org/r/[email protected]
|
|
phyFLEX are SoMs based on the FPSC standard.
Add additional "SOM types" for the phyFLEX modules base on the
FPSC Gamma specification. These modules come in four different
variants; prototypes (PT), standard product (SP), KSP (KP) and
KSM (KM).
Signed-off-by: Daniel Schultz <[email protected]>
Reviewed-by: Teresa Remmet <[email protected]>
Tested-by: Dominik Haller <[email protected]>
|
|
Assign the return value of snprintf (total length) to a variable to
properly check if the string has the correct length.
Currently, this variable is always zero and the length check after
snprintf will always fail.
Signed-off-by: Daniel Schultz <[email protected]>
|
|
Add variable 'emmc_dev' and 'sd_dev' required for NXP uuu flash scripts.
Signed-off-by: Primoz Fiser <[email protected]>
|
|
Set boot_targets environment variable dynamically, so that when booting
from SD-card, boot binaries are also preferably fetched from the SD-card
by default. If the user decides to set their own boot_targets, we should
not overwrite them.
Signed-off-by: Primoz Fiser <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
|
|
Enable standard boot for the phyCORE-i.MX93 board and use it as a new
default. Add required standard boot variables to the environment, while
removing old boot scripts and now unnecessary environment variables.
Adjust variables according to the requirements of PHYTEC ampliphy-boot
distro-boot. Last but not least, order environment vars by alphabet and
run 'make savedefconfig' to resync defconfig.
Signed-off-by: Primoz Fiser <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
|
|
Sort all .env files alphabetically like it is already done for
phycore_imx8mp.
Signed-off-by: Benjamin Hahn <[email protected]>
|
|
fdtoverlay_addr_r is the correct variable name according to standardboot
documentation and already used for phycore_imx8mp.
Signed-off-by: Benjamin Hahn <[email protected]>
|
|
We want to change the bootdevice dynamically, so that when booting
U-Boot from sdcard, kernel is also preferably booted from sdcard by
default. If the user decides to set their own bootorder, this should not
be overwritten. This was already implemented for imx8mp-libra-fpsc
board, but as we set the default value for boot_targets in devicetree
now, the env_get_default will return NULL. Also env_get might return
NULL when boot_targets is not set. A string compare with NULL is unsafe
and should be avoided. To fix this we only change the env value if the
variable was not set before (NULL), as this is the new default value.
In any other case the user has changed the value so it will not be
overwritten.
Also let standardboot set bootcmd automatically. For this
CONFIG_USE_BOOTCOMMAND needs to be activated.
Signed-off-by: Benjamin Hahn <[email protected]>
|
|
Standardboot allows setting bootdevices and bootmeths in devicetree.
This is already implemented for imx8mp-libra board.
Signed-off-by: Benjamin Hahn <[email protected]>
|
|
Add emmc_dev and sd_dev env variables with comment that they are needed
for builtin uuu flash scripts. This is already done for imx8mp-libra
board.
Signed-off-by: Benjamin Hahn <[email protected]>
|
|
Netboot script is named net_boot_fit.scr.uimg with ampliphy-boot.
fit_fdtconf is not longer needed. The default config is automatically
fetched from the fitImage. mmcroot is also not longer used, the
bootscript has a builtin default. bootenv_addr_r is no longer used, as
the bootenv is loaded into loadaddr.
Signed-off-by: Benjamin Hahn <[email protected]>
|
|
The current spl_board_fixups API allows for modification of spl_image
before the SPL jumps to it. This can be used to modify the DT for the
next boot stage, however the current API only allows either the machine
arch or the board to use it.
This limits the utility of the API as there might be certain fixups that
should be applied to all boards sharing the same machine architecture
with others being board specific.
For TI's K3 specifically, this prevents us from performing architecture
level fixups since a lot of TI boards are already making use of the
spl_board_fixups API.
Therefore this patch splits the API into two to allow both board and the
architecture specific fixups. The order is kept as arch then board to
give board specific fixups the precedence.
Reviewed-by: Dhruva Gole <[email protected]>
Signed-off-by: Anshul Dalal <[email protected]>
Tested-by: Wadim Egorov <[email protected]>
|
|
Add rauc to bootmeths variable if BOOTMETH_RAUC is enabled. This is
setting a proper default for RAUC enabled systems.
Signed-off-by: Martin Schwan <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-socfpga into next
SoCFPGA updates for v2025.10:
CI: https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/27762
This pull request brings a set of updates across SoCFPGA platforms
covering Agilex5, Agilex7, N5X, and Stratix10. The changes include:
* Agilex5 enhancements:
- USB3.1 enablement and DWC3 host driver support
- System Manager register configuration for USB3
- Watchdog timeout increase and SDMMC clock API integration
- dcache handling improvements in SMC mailbox path
- Enable SPL_SYS_DCACHE_OFF in defconfig
* Clock driver improvements:
- Introduce dt-bindings header for Agilex clocks
- Add enable/disable API and EMAC clock selection fixes
- Replace manual shifts with FIELD_GET usage
* DDR updates:
- IOSSM mailbox compatibility check
- Correct DDR calibration status handling
* Device tree changes:
- Agilex5: disable cache allocation for reads
- Stratix10: add NAND IP node
- Enable driver model watchdog
- Enable USB3.1 node for Agilex5
* Config cleanups:
- Simplify Agilex7 VAB defconfig
- Remove obsolete SYS_BOOTM_LEN from N5X VAB config
- Enable CRC32 support for SoCFPGA
- Increase USB hub debounce timeout
Overall this set improves reliability of DDR and cache flows,
adds missing USB and MMC features for Agilex5, and refines clock
and configuration handling across platforms.
This patch set has been tested on Agilex 5 devkit, and Agilex devkit.
|
|
The error message in phytec_get_product_name() was missing a newline,
causing log output to be concatenated with subsequent messages. Add
the newline to improve readability.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
After switching our boards to standard boot, we observed that the
kernel hangs when booting with the "script" boot method over the
network.
The original scriptaddr value was copied from ti_common.env and
remained unused for some time. On phycore-am62x and phycore-am62ax,
however, this address conflicts with the current location where
ATF is loaded (CONFIG_K3_ATF_LOAD_ADDR).
Move scriptaddr to 0x89100000, directly after fdtoverlay_addr_r.
The phycore-am64x is not affected by this issue, but we update it
as well to keep all phycore-am6xx boards consistent.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Anshul Dalal <[email protected]>
|
|
Prepare v2025.10-rc5
|
|
OP-TEE configs are enabled by default, change the doc to no longer
declare OP-TEE as optional. Also remove CFG_TEE_BENCHMARK as it is no
longer present in optee_os.
Further, phycore-imx8mm and imx8mm-phygate-tauri-l use different build
instructions, so dissolve the common file for building OP-TEE.
Reviewed-by: Teresa Remmet <[email protected]>
Signed-off-by: Yannic Moog <[email protected]>
|
|
Fix support for i.MX93 voltage modes on phyCORE-i.MX93 SoM boards.
First of all, Kconfig option CONFIG_IMX9_LOW_DRIVE_MODE is gone since
commit c9efcad23741 ("imx93_evk: Remove CONFIG_IMX9_LOW_DRIVE_MODE and
ld defconfig") and was replaced by runtime detection mechanism. Thus
lets use is_voltage_mode() instead of Kconfig to detect CPU type and
select proper voltage mode.
Secondly, 1400MHz ND mode (Nominal Drive) requiring 0.85V BUCK voltage
was not supported with current power_init_board() PMIC settings. Add
check also for this CPU type and set BUCK voltage accordingly.
Last but not least, add printf() printouts about PMIC voltage mode to
the console. This makes it more apparent and verbose about voltage mode
in use. Also our internal tests depend on this printout to catch issues
with i.MX93 CPU types and set PMIC voltage modes.
Signed-off-by: Primoz Fiser <[email protected]>
|
|
Add new imx8mp-libra-fpsc board.
Bootph tags as well as USB device tree nodes are in u-boot.dtsi for now
and will be removed when upstreamed.
The Libra i.MX 8M Plus FPSC is a single board computer. It uses an i.MX
8M Plus FPSC [1] System on Module which utilizes the FPSC standard [2].
[1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-8m-plus-fpsc
[2] https://www.phytec.eu/en/produkte/system-on-modules/fpsc
Signed-off-by: Benjamin Hahn <[email protected]>
Reviewed-by: Teresa Remmet <[email protected]>
Tested-by: Teresa Remmet <[email protected]>
Signed-off-by: Yannic Moog <[email protected]>
|
|
Switch to use CONFIG_PHYTEC_EEPROM_BUS instead of the hard coded value
of 2 for the EEPROM I2C bus for both SPL and U-Boot proper. Possible
since commit 88a1816a9b4e ("board: phytec: common: Add PHYTEC_EEPROM_BUS
to Kconfig").
Signed-off-by: Primoz Fiser <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
|
|
Wadim Egorov <[email protected]> says:
Update Kconfig options for phyCORE-AM62Ax to align with other boards and
prepare common board code for the upcoming phyCORE-AM62L which has the
SoM EEPROM connected on a different bus.
Link: https://lore.kernel.org/r/[email protected]
|
|
Drop SUPPORT_EXTENSION_SCAN and enable PHYTEC_SOM_DETECTION_BLOCKS
to align with other PHYTEC platforms. These options were missed when
phyCORE-AM62Ax support was added.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Use CONFIG_PHYTEC_EEPROM_BUS instead of the hard coded value for the i2c bus.
Signed-off-by: Dominik Haller <[email protected]>
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Add the option to choose a different bus number than 0 for the i2c eeprom
based som detection.
Signed-off-by: Dominik Haller <[email protected]>
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Prepare v2025.10-rc3
|
|
Add rauc to bootmeths variable if BOOTMETH_RAUC is enabled.
This is setting a proper default for RAUC enabled systems.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Martin Schwan <[email protected]>
|
|
Fix PHYTEC EEPROM bus mismatch between SPL and U-Boot proper by enabling
CONFIG_SPL_DM_SEQ_ALIAS=y on phyCORE-i.MX93 boards. This way, both the
SPL and U-Boot proper will respect the device-tree aliases for I2C devs
and use the same I2C bus number for phytec_eeprom_data_setup() function
calls. This makes code less confusing and more robust.
Fixes an issue apparent since commit 79f3e77133bd ("Subtree merge tag
'v6.16-dts' of dts repo [1] into dts/upstream") where SPL would spew the
following error:
phytec_eeprom_read: i2c EEPROM not found: -110.
phytec_eeprom_data_setup: EEPROM data init failed
While later in U-Boot proper, EEPROM would be successfully read out.
This happens because Linux device-tree for phyBOARD-Segin-i.MX93 since
aforementioned commit enables I2C bus 2 (lpi2c2 is used for audio codec
and RTC) which breaks SPL I2C bus number ordering and I2C EEPROM bus is
shifted by +1. Now, lets prevent this from happening again by utilizing
device-tree aliases also in the SPL.
Signed-off-by: Primoz Fiser <[email protected]>
|
|
Making the setup_mac_from_eeprom optional for boards without
CONFIG_PHYTEC_SOM_DETECTION_BLOCKS.
Signed-off-by: John Ma <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
|
|
watchdogs in U-Boot"
This series from Wadim Egorov <[email protected]> cleans up how
watchdogs are handled on some phytec TI K3 platforms.
Link: https://lore.kernel.org/r/[email protected]
|
|
Allows run-time control over watchdog auto-start and the timeout via
setting the environment variable watchdog_timeout_ms. A value of zero
means "do not start". Use CONFIG_WATCHDOG_TIMEOUT_MSECS as initial value.
Users can enable the watchdog to monitor the boot process until userspace
or OS takes over to serve the watchdog.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Allows run-time control over watchdog auto-start and the timeout via
setting the environment variable watchdog_timeout_ms. A value of zero
means "do not start". Use CONFIG_WATCHDOG_TIMEOUT_MSECS as initial value.
Users can enable the watchdog to monitor the boot process until userspace
or OS takes over to serve the watchdog.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Allows run-time control over watchdog auto-start and the timeout via
setting the environment variable watchdog_timeout_ms. A value of zero
means "do not start". Use CONFIG_WATCHDOG_TIMEOUT_MSECS as initial value.
Users can enable the watchdog to monitor the boot process until userspace
or OS takes over to serve the watchdog.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
For phyCORE-i.MX93 SoMs with i.MX93 parts running in VOLT_LOW_DRIVE mode
(SoCs with speed grade fuse set to 900 MHz) reduce usdhc clocks from 400
MHz to 266 MHz. Do this in board code since global imx9 board_fix_fdt()
is not used in case of phycore-imx93 board since commit d3b9b7996889
("board: phytec: imx93: Add eeprom-based hardware introspection").
While at it, add a note to ft_board_setup() function to inform that
fixup for Linux device-tree is taken care by ft_system_setup() in imx9
global arch/arm/mach-imx/imx9/soc.c implementation.
Signed-off-by: Primoz Fiser <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27149
- Add support for the NXP imx93 frdm board.
- imx93_evk and phycore-imx93 cleanups.
- Convert imx6dl-sielaff to OF_UPSTREAM and fix serial download mode boot.
- Fix crash in imx power-domain.
- Migrate Phytec imx8mm boards to standard boot.
- Fix smatch warnings.
|
|
Commit 86acdce2ba88 ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <[email protected]>
Tested-by: Adam Ford <[email protected]> #imx8mm_beacon
Tested-by: Bryan Brattlof <[email protected]>
Acked-by: Peng Fan <[email protected]> #NXP boards
|
