summaryrefslogtreecommitdiff
path: root/board/qualcomm/qcs404-evb
AgeCommit message (Collapse)Author
2024-03-01board: qcs404-evb: drop board codeCaleb Connolly
This board is entirely supported by the generic arch code and DTS. The board code used to handle turning on the vbus regulator, however this is now handled via DT. With this, the board specific defconfig is also no longer needed, so drop it as well. Reviewed-by: Neil Armstrong <[email protected]> Reviewed-by: Sumit Garg <[email protected]> Tested-by: Sumit Garg <[email protected]> #qcs404 Signed-off-by: Caleb Connolly <[email protected]>
2024-03-01mach-snapdragon: generalise board supportCaleb Connolly
Historically, Qualcomm boards have relied on heavy hardcoding in U-Boot, in many cases to the specific SoC but also to the board itself (e.g. memory map). This has been largely resolved by modernising the Qualcomm drivers in U-Boot, however the board code still largely follows this model. This patch removes the board specific memory maps and duplicated board init code, replacing it with generic init code. The memory map is now built at runtime based on data read from DT, this allows for the memory map to be provided without having to recompile U-Boot. Support is also added for booting with appended DTBs, so that the first-stage bootloader can populate the memory map for us. The sdm845 specific init code is dropped entirely, it set an environment variable depending on if a button was pressed, but this variable wasn't used in U-Boot, and could be written to use the button command instead. The KASLR detection is also dropped as with appended dtb, the kaslr seed can be read directly from the DTB passed to U-Boot. A new qcom_defconfig is added, with the aim of providing a generic U-Boot configuration that will work on as many Qualcomm boards as possible. It replaces the defconfig files for the Dragonboard 845c, Galaxy S9, and QCS404 EVB. For now the db410c and 820c are excluded as they still have some board code left. Similarly, the config headers for db845c, starqltechn, and qcs404-evb are replaced by a single qcom header. The previously db410c-specific board_usb_init() function is made to be generic and is added to mach-snapdragon. While we lack proper modelling for USB configuration, using a well-known named pinctrl state is a reasonably generic middleground, and works using upstream DT. This function will do nothing unless the USB node has a pinctrl state named "device", in which case it will be set when entering USB peripheral mode. Reviewed-by: Neil Armstrong <[email protected]> Reviewed-by: Sumit Garg <[email protected]> Tested-by: Sumit Garg <[email protected]> #qcs404 Signed-off-by: Caleb Connolly <[email protected]>
2022-08-26board: qcs404-evb: Enable USB3 specific PMIC GPIOSumit Garg
For USB3 host controller to detect devices on the bus it is required to enable a PMIC GPIO: usb_vbus_boost_pin. So enable that during board specific initialization. And since this PMIC GPIO parsing is quite u-boot specific, so add a DT override to qcs404-evb-uboot.dtsi to represent usb_vbus_boost_pin. Signed-off-by: Sumit Garg <[email protected]>
2022-07-25board: qualcomm: Add support for QCS404 EVBSumit Garg
Add support for Qualcomm QCS404 SoC based evaluation board. Features: - Qualcomm Snapdragon QCS404 SoC - 1GiB RAM - 8GiB eMMC, uSD slot U-boot is chain loaded by ABL in 64-bit mode as part of boot.img. For detailed build and boot instructions, refer to doc/board/qualcomm/qcs404.rst. Signed-off-by: Sumit Garg <[email protected]>