| Age | Commit message (Collapse) | Author |
|---|
|
It is not functionally possible to use the code enabled by
PARTITION_TYPE_GUID without having EFI_PARTITION be enabled as well. Not
all users of the former had ensured that the latter was enabled however,
so audit all current users and then as appropriate select or imply
EFI_PARTITION as needed.
Signed-off-by: Tom Rini <[email protected]>
|
|
The symbol CONFIG_IP_DYN does not exist, but multiple contributors
copied an imply statement.
Remove the imply IP_DYN statements.
Fixes: 3fda0262c33f ("riscv: Add SiFive FU540 board support")
Fixes: 64413e1b7caf ("riscv: Add Microchip MPFS Icicle Kit support")
Fixes: 70415e1e528d ("board: sifive: add HiFive Unmatched board support")
Fixes: 6f902b85b6ee ("board: starfive: Add Kconfig for StarFive VisionFive v2 Board")
Signed-off-by: Heinrich Schuchardt <[email protected]>
Acked-by: Conor Dooley <[email protected]>
|
|
CONFIG_OF_BOARD isn't enabled on SiFive Unleashed and Unmatched, thus
board_fdt_blob_setup is actually dead code on these platforms. Let's
remove it.
Signed-off-by: Yao Zi <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
GPIO reset and power-off functionality depends on device tree data, which
is often absent in SPL or TPL. To address this, incorporate PHASE_ into the
config option and add Kconfig option or each phase.
Adjust SYSRESET_GPIO and POWEROFF_GPIO uses to address possible
regressions.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
This returns a devicetree and updates a parameter with an error code.
Swap it, since this fits better with the way U-Boot normally works. It
also (more easily) allows leaving the existing pointer unchanged.
No yaks were harmed in this change, but there is a very small code-size
reduction.
For sifive, the OF_BOARD option must be set for the function to be
called, so there is no point in checking it again. Also OF_SEPARATE is
defined always.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
[trini: Update total_compute]
Signed-off-by: Tom Rini <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
Rename spl_soc_init() to spl_dram_init() because the generic function
name does not reflect what the function actually does. Also
spl_dram_init() is commonly used for dram initialization and should be
called from board_init_f().
Signed-off-by: Lukas Funke <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Now all linker symbols are declared as type char[]. Though we can
reference the address via both the array name 'var' and its address
'&var'. It's better to unify them to avoid confusing developers.
This patch converts all '&var' linker symbol refrences to the most
commonly used format 'var'.
Signed-off-by: Shiji Yang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_SIFIVE_OTP defined in Kconfig
Signed-off-by: Simon Glass <[email protected]>
|
|
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <[email protected]>
|
|
When using QEMU to have a quick test of booting U-Boot S-mode payload
directly without the needs of preparing the SPI flash or SD card images
for SiFive Unleashed board, as per the instructions [1], it currently
does not boot any more.
This was caused by the OF_PRIOR_STAGE removal, as gd->fdt_blob no longer
points to a valid DTB. OF_BOARD is supposed to replace OF_PRIOR_STAGE,
hence we need to add the OF_BOARD logic in board_fdt_blob_setup().
[1] https://qemu.readthedocs.io/en/latest/system/riscv/sifive_u.html#running-u-boot
Fixes: 2e8d2f88439d ("riscv: Remove OF_PRIOR_STAGE from RISC-V boards")
Fixes: d6f8ab30a2af ("treewide: Remove OF_PRIOR_STAGE")
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
OF_HOSTFILE is used on sandbox configs only. Although it's pretty
unique and not causing any confusions, we are better of having simpler
config options for the DTB.
So let's replace that with the existing OF_BOARD. U-Boot would then
have only three config options for the DTB origin.
- OF_SEPARATE, build separately from U-Boot
- OF_BOARD, board specific way of providing the DTB
- OF_EMBED embedded in the u-boot binary(should not be used in production
Signed-off-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The following warning is seen in unleashed.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast with uintptr_t.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Commit 47d73ba4f4a4 ("board: sifive: overwrite board_fdt_blob_setup in u-boot proper")
added a board-specific implementation of board_fdt_blob_setup() which
takes a pointer as the return value, but it does not return anything
if CONFIG_OF_SEPARATE is not enabled. This will cause a build warning
seen when testing booting S-mode U-Boot directly from QEMU, per the
instructions in [1]:
board/sifive/unleashed/unleashed.c: In function ‘board_fdt_blob_setup’:
board/sifive/unleashed/unleashed.c:125:1: warning: control reaches end of non-void function [-Wreturn-type]
Return &_end as the default case.
[1] https://qemu.readthedocs.io/en/latest/system/riscv/sifive_u.html#running-u-boot
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
Prepare v2021.10-rc4
Signed-off-by: Tom Rini <[email protected]>
# gpg: Signature made Tue 14 Sep 2021 06:58:32 PM EDT
# gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <[email protected]>" [ultimate]
# Conflicts:
# board/Arcturus/ucp1020/spl.c
# cmd/mvebu/Kconfig
# common/Kconfig.boot
# common/image-fit.c
# configs/UCP1020_defconfig
# configs/sifive_unmatched_defconfig
# drivers/pci/Kconfig
# include/configs/UCP1020.h
# include/configs/sifive-unmatched.h
# lib/Makefile
# scripts/config_whitelist.txt
|
|
This adds genimage [1] config files for generating SD card and spi-nor
images, which can be programmed to an SD card or SPI flash and boot
from there.
The same images will be used for U-Boot CI testing for this board.
[1] https://github.com/pengutronix/genimage
Signed-off-by: Bin Meng <[email protected]>
|
|
Invokes the common cache_init function to initialize ccache.
Signed-off-by: Zong Li <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
Add board_fdt_blob_setup to return the device tree location which is
passed by prior stage in u-boot proper. The generic board_fdt_blob_setup
always returns _end, it mignt be ok because u-boot SPL would currently
put the dtb there, but it would be broken if we put the dtb to another
place and assigned the location into a1 register for u-boot proper. Use
the location passed by prior stage would make more sence, because we
actually pass the location to u-boot proper and want to use that one,
rather than the dtb which in _end.
We can't use CONFIG_OF_PRIOR_STAGE because it doens't distinguish the
implementation of u-boot SPL and u-boot proper, so u-boot SPL need to
reply on the prior stage to pass device tree location as well, but we
don't pass the DT from boot rom now. In addition, when
CONFIG_OF_PRIOR_STAGE is enabled, the u-boot-spl.bin and u-boot.itb won't
include the device tree.
Signed-off-by: Zong Li <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
As (3581811dc26f "riscv: sifive/fu540: Move SPL related functions to spl.c"),
we put the SPL stuff in spl.c, we don't need to compile unleashed.c and
unmatched.c in SPL build.
Signed-off-by: Zong Li <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
At present SiFive Unleashed board uses the Makefile to create the FIT,
using USE_SPL_FIT_GENERATOR, which is deprecated as per the Makefile
warning. Update to use binman instead.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
