| Age | Commit message (Collapse) | Author |
|---|
|
Clearfog GTR has an assembly option for a SATA connector, CON18.
It shares the serdes with mini-pcie connector CON3.
Add new kconfig option to select betweenata and pci, defaulting to pci
as it was previously configured in board-file.
Clearfog GTR connects eth2 / serdes 1 to a 2.5Gbps capable ethernet
switch port. Linux already configures a fixed-link at speed 2500 from
device-tree.
Upgrade serdes 1 rate to 3.125Gbps to support a 2.5Gbps network link on
Clearfog GTR.
Signed-off-by: Josua Mayer <[email protected]>
|
|
Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
SATA and UART ClearFog imaages are not buildable as ENV_SECT_SIZE is not defined
set values for both possible targets
Signed-off-by: Dennis Gilmore <[email protected]>
|
|
Migrate the values for ENV_SIZE and ENV_OFFSET into board specific
Kconfig defaults so they're more accessible for configuration.
Signed-off-by: Joel Johnson <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add reasonable default SPI offsets and ENV size when configured to
boot from SPI flash.
Signed-off-by: Joel Johnson <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The mPCIe slots on ClearFog Pro and ClearFog Base may be alternately
configured for SATA usage.
Signed-off-by: Joel Johnson <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
While newer Linux kernels provide autoconfiguration of SFP, provide
an option for setting in U-Boot Kconfig for use prior to booting.
Signed-off-by: Joel Johnson <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add a unique entry for ClearFog Base variant, reflected in the board
name and adjusted SerDes topology.
Signed-off-by: Joel Johnson <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
